Frico Thermocassette HP3N, Thermocassette HP6N Original Instructions Manual

Thermocassette HP

.... 9 ... 17.... 13 .... 15

.... 11

GB

FR NO DE SE

... 19

FI

... 21

RU

Original instructions

Thermocassette HP

2

GB

FR

EU-kommissionens Ecodesignförordning (EU) 2015/1188 för rumsvärmare skiljer på
användningsområden för olika installationer.

Förordningen gäller då installationen är avsedd att skapa värmekomfort för människor som
vistas i lokalen. Förordningen gäller inte för installationer som är avsedda för värmebehov
av mer teknisk art såsom grundvärme i maskinrum, värmebehov i produktionsprocesser,
frostskydd, etc. Förordningen gäller heller inte installationer i fordon, offshore eller utomhus.

Många av Fricos produkter kan användas både som rumsvärmare (definierade enligt
(EU) 2015/1188) och som värmare för tekniska behov. Vid installationstillfället är det upp
till ansvarig installatör att bedöma om Ecodesignförordningen är applicerbar eller inte.
Regleringslösningar för installationer som inte omfattas av Ecodesignförordningen redovisas i
separat tabell.

SE

NO

Ecodesign Regulation (EU) 2015/1188 concerning local space heaters does not apply to all
application areas.

The Regulation applies when an installation is intended to provide thermal comfort for people
in the premises. The Regulation does not apply to heating installations of a more technical
nature e.g. in engineering/utility rooms, in production processes, frost protection, etc. The
Regulation also does not apply to installations in vehicles, offshore or outdoors.

Many of Frico's products can be used as both local space heaters (as defined in (EU) 2015/1188)
and for technical heating purposes. It is up to the installer responsible for the installation
to assess whether the Ecodesign Regulation is applicable or not. Control solutions for
installations not covered by the Ecodesign Regulation are listed in a separate table.

Økodesigndirektivet (EU) 2015/1188 som gjelder varmeovner, gjelder ikke alle bruksområder.

Direktivet gjelder når en installasjon har som formål å skape en komfortabel temperatur for
personene på stedet. Direktivet gjelder ikke til oppvarmingsinstallasjoner av det mer tekniske
slaget, som i produktutviklingsrom, bruksområder, i produksjonsprosesser, frostbeskyttelse etc.
Direktivet gjelder heller ikke installasjoner som befinner seg i kjøretøy, offshore eller utendørs.

Mange av Fricos produkter kan brukes både som varmeovner (som definert i 2015/1188) og til
formål innen teknisk oppvarming. Det er opp til installatøren som er ansvarlig for installasjonen
å vurdere hvorvidt Økodesigndirektivet er gjeldende eller ikke. Reguleringsløsninger for
installasjoner som ikke dekkes av Økodesigndirektivet står oppført i en separat tabell

La réglementation relative à l'écoconception (UE) 2015/1188 concernant les dispositifs de
chauffage décentralisés ne s'applique pas à tous les cas.

Elle s'applique lorsqu'une installation est destinée à assurer un confort thermique à des
personnes dans les locaux. Elle ne s'applique pas au chauffage d'installations d'une nature
plus technique (salles des machines/de service, processus de production, protection contre le
gel, etc.). Elle ne s'applique pas non plus aux installations qui se trouvent à bord de véhicules,
offshore ou en extérieur.

De nombreux produits Frico peuvent être utilisés comme des dispositifs de chauffage
décentralisés (tel que défini dans la réglementation (UE) 2015/1188) et à des fins de chauffage
technique. Il appartient à l'installateur de déterminer si la réglementation relative à
l'écoconception s'applique ou non. Les solutions de contrôle pour les installations qui ne sont
pas couvertes par la réglementation relative à l'écoconception sont présentées dans un tableau
distinct.

Thermocassette HP

3

FI

DE

RU

Die Ökodesign-Verordnung (EU) 2015/1188 über Einzelraumheizgeräte trifft nicht auf alle
Anwendungsgebiete zu.

Die Verordnung findet Anwendung, wenn eine Installation dazu bestimmt ist, innerhalb
eines Raumes ein für den Menschen angenehmes Temperaturniveau zu erreichen. Die
Verordnung findet keine Anwendung auf Heizungsinstallationen technischer Natur, z. B. in
Technik-/Wirtschaftsräumen, bei Produktionsprozessen, für Frostschutz usw. Die Verordnung
findet ebenfalls keine Anwendung bei Installationen in Fahrzeugen, Offshoreanlagen und
Außenbereichen.

Viele Frico-Produkte können sowohl als Einzelraumheizgerät (gemäß Definition nach (EU)
2015/1188) als auch für technische Heizprozesse eingesetzt werden. Der Monteur, der für die

Installation verantwortlich ist, muss beurteilen, ob die Ökodesign-Verordnung anwendbar ist
oder nicht. Steuerungslösungen für Installationen, die nicht unter die Ökodesign-Verordnung

fallen, sind in einer separaten Tabelle aufgelistet.

Paikallisia tilalämmittimiä käsittelevä Ecodesign-asetus (EU) 2015/1188 ei kata kaikkia käyttökohteita.

Asetus on voimassa ainoastaan silloin, kun lämmittimellä halutaan parantaa tiloissa olevien
ihmisten lämpömukavuutta. Asetus ei koske teknisempiä lämmitysjärjestelmiä esim.
konehuoneissa/kodinhoitohuoneissa, tuotantoprosesseissa, pakkassuojausta, jne. Asetus ei
myöskään koske ajoneuvoissa, laivoissa ja ulkona käytettäviä järjestelmiä.

Useita Frico-tuotteita voidaan käyttää sekä paikallisina tilalämmittiminä (asetuksen (EU) 2015/1188
mukaan) että teknisempiin lämmitystarkoituksiin. Asentajan on määritettävä sovelletaanko
asennukseen Ecodesign-asetusta vai ei. Ohjausratkaisut asennuksiin, joita Ecodesign-asetus ei
käsittele, on lueteltu erillisessä taulukossa

Положения требований Экодизайн (EU) 2015/1188 по приборам локального обогрева не
охватывают все возможные области их применения.

Требования Экодизайн применяются, когда установка предназначена для обеспечения теплового
комфорта людей в помещениях. Эти Требования не распространяются на установки и системы
обогрева более сложного технического характера, например, при обогреве технических,
служебных и производственных помещений, при организации защиты от замерзания и т. д.
Также требования Экодизайн не применяются в случае установки оборудования в транспортных
средствах, сооружениях на море и на открытых площадках.

Многие виды оборудования Frico могут применяться как в качестве приборов локального
обогрева (как определено нормативами (EU) 2015/1188) так и в качестве составных частей
обогревательных систем общественных и производственных зданий. Ответственность за

определение необходимости применения или не применения требований Экодизайн несет
организация, осуществляющая монтаж данного оборудования. Приборы управления для

установок оборудования, не подпадающих под положения требований Экодизайн, перечислены в
отдельной таблице.

Thermocassette HP

4

HP6N

HP3N

[mm]

A 80
B 50
C 500
D 1800

Fig. 1

Minimum mounting distance

Flammable material

1,8 m

1,8 m

Thermocassette HP

5

Mounting

Fig. 2

A

B

C

D

E

Fig. 1

Thermocassette HP

6

Technical specifications

Type Output (1)

[W]

Voltage (2)

[V]

Amperage (3)

[A]

Max. surface
temperature (4)
[°C]

Weight (5)

[kg]

HP3N 300 230V~ 1,3 100 5,8
HP6N 600 230V~ 2,6 100 10,7

Protection class: IP55
CE compliant.
Complies with the requirements for flammable areas according to SEMKO 111FF.

(1)
SE: Effekt
GB: Output
NO: Effekt
FR: Puissance
DE: Heizleistung
RU: Мощность
FI: Lämmitysteho

(2)
SE: Spänning
GB: Voltage
NO: Spenning
FR: Tension
DE: Spannung
RU: Напряжение
FI: Jännite

(3)
SE: Ström
GB: Amperage
NO: Strøm
FR: Intensité
DE: Stromstärke
RU: Ток
FI: Virta

(4)
SE: Maximal yttemperatur
GB: Max. surface temperature
NO: Maksimal overflatetemp.
FR: Température de surface
DE: Max. Oberflächentemperatur
RU: Max. температура поверхности
FI: Suurin pintalämpötila

(5)
SE: Vikt
GB: Weight
NO: Vekt
FR: Poids
DE: Gewicht
RU: Вес
FI: Paino

SE: Uppfyller kraven för brandfarliga rum enligt SEMKO 111FF.
GB: Complies with requirements of flammable areas according to SEMKO 111FF.
NO: Oppfyller kravene til antennelige områder i henhold til SEMKO 111FF.
FR: Conforme aux normes sur les zones inflammables d'après SEMKO 111FF.
DE: Erfüllt die Anforderungen an brennbare Bereiche gemäß SEMKO 111FF.
FI: Täyttää palovaarillisille tiloille asetetut vaatimukset SEMKO111FF mukaisesti.

RU: Отвечает требованиям по пожарной безопасности в соответствии со стандартм SEMKO 111FF.

Thermocassette HP

7

Type HxWxD

[mm]

TAP16R

87x87x53

TEP44

87x87x55

RTX54

82x88x25

SKG30 115x85x40

TAP16R TEP44 RTX54

SKG30

Accessories

Controls

Controls for installations not covered by the Ecodesign Regulation (EU) 2015/1188

SE: Regleringar för installationer som inte omfattas av Ecodesign, förordning (EU) 2015/1188
NO: Reguleringsløsninger for installasjoner som ikke dekkes av Økodesigndirektivet (EU) 2015/1188
FR: Régulations pour les installations non couvertes par la réglementation relative à l’écoconception
(UE) 2015/1188
DE: Steuerungen für Installationen, die nicht unter die Ökodesign-Verordnung (EU) 2015/1188 fallen
FI: Ohjausratkaisut asennuksiin, joita Ecodesign-asetus (EU) 2015/1188 ei käsittele

RU: Приборы управления для установок оборудования, не подпадающих под нормы требований Экодизайн
(EU) 2015/1188

Type

74701 Wire mounting kit

Type HxWxD

[mm]

KRT1900 165x57x60
KRTV19 165x57x60

KRT1900 KRTV19

Thermocassette HP

8

L

N

HP

L

N

HP

L

N

HP

P

230V~

N

Thermostat

L

N

HP

230V~

TAP16R

TAP16R

SKG30

HP HP

Brown

Blue

Brown

Blue

LN

LN

T2 T1

LOAD

LOAD

LOAD

LOAD

SENSOR

SENSOR

SENSOR

SENSOR

230V~

230V~

Wiring diagram

Controls for installations not covered by the Ecodesign Regulation (EU) 2015/1188

Thermocassette HP

8

GB

Application area

The heating panel is intended for the heating
of rooms requiring free walls. The panel
can be used for complete heating, or as an
additional heater (e.g. over a reception desk
or other work place).

There are two ratings: 300 W and 600 W.

The heating panel provides mainly radiation
heating. This implies that to obtain the
same experienced temperature it is possible
to reduce the air temperature in the room,
which saves energy.

Because of the low surface temperature,
max 100°C, the heating panel is suitable
for rooms with relatively low ceiling height.
Thanks to the location, the panel is protected
from any physical contact or damage. There
is no risk of being burned.

Mounting

Integrated in ceiling (put in exposed grid)
See fig. 1

1. Lateral distance to wall shall be at least
50 mm.

2. The heater(s) should only be wired by a

competent electrician, and in accordance
with existing national regulations.

3. Place the cassette in the required ceiling

square. Minimum design height ”H” for
dismounting, T-profile 32x15: 150 mm,

T-profile 38x24: 200 mm. NOTE! Avoid

fixing vertical bars in the T-profile where a
heating panel is to be installed. The panel
fills out the whole square.

4. Connect the panel.

5. The second last page in this mounting

instruction is to be filled out and fixed
adjacent to the distribution board and it
has to contain (drawing) the locations of
the heating units.

Bracket mounting
See fig. 2

1. Mounting height above floor shall be at
least 1,8 m, and lateral distance to wall at
least 50 mm. When mounting in gypsum
board, make sure that the mounting
brackets are anchored in the beam behind.
During long-term high temperatures the
strength of the board is reduced.

2. The heater(s) should only be wired by a
competent electrician, and in accordance
with existing national regulations.

3. Measure, drill and screw the two loose
brackets to the ceiling. Do not tighten the
screws yet. It is important that the holes
come at right angles, cross measure. (fig.
2A)

4. Hook the panel brackets to the ones on the
ceiling (only the side nearest to the cable
gland). Allow panel to hang vertical. (fig.
2B)

5. Connect the panel.

6. Swing up the panel, and adjust the lateral
position of the ceiling mounted brackets.
(fig. 2C)

7. Swing down the panel and tighten the
screws in the ceiling. (fig. 2D)

8. Swing up the panel again and hook the
panel bracket ends in the ceiling brackets.
NOTE! Make sure that the brackets do not
become unhooked at the other end.

9. Secure the panel with a screw (enclosed
on delivery) at each hanging point. (fig.
2E)

10.The second last page in this mounting
instruction is to be filled out and fixed
adjacent to the distribution board and it
has to contain (drawing) the locations of
the heating units.

Replacement of cable

1. Because of limitations in the IP55 category
the cable cannot be changed.

2. If the cable is damaged the unit has to be
scrapped.

Installation and operating instructions

General Instructions

Read these instructions carefully before
installation and use. Keep this manual for
future reference.

The product may only be used as set out in
the assembly and operating instructions. The
guarantee is only valid if the product is used
in the manner intended and in accordance
with the instructions.

Thermocassette HP

9

GB

Control

When using this product as a local space
heater according to Ecodesign Regulation
(EU) 2015/1188, it must be supplemented
with one of the following approved controls.

• TAP16R, electronic thermostat that
includes:

- Electronic room temperature control plus
week timer

- Room temperature control with open
window detection

- Adaptive start control

• TAP16R and SKG30, black bulb sensor that
include:

- Electronic room temperature control plus
week timer

- Room temperature control with open
window detection

- Adaptive start control

- Black bulb sensor

The product can be controlled in a different
way, e.g. by an overall control system (BMS),
but in that case the responsibility lies with
the installer to ensure that the control system
is programmed to make the installation meet
the requirements of Ecodesign Regulation
(EU) 2015/1188.

Packaging

Packaging materials are chosen with
consideration to environment and are
therefore recyclable.

Handling of product at end of working life

This product may contain substances
necessary for functionality of product but
potentially dangerous for the environment.
The product should not be disposed
mixed with general household waste but
delivered to a designated collection point for
environmental recycling. Please contact local
authority for further details of your nearest
designated collection point. Recycling of used
products saves earth's resources and reduces
global footprint.

Safety

• For all installations of electrically heated
products should a residual current circuit
breaker 300 mA for fire protection be used.

• The unit may have hot surfaces during
operation and when cooling down!

• The unit must not be fully or partially
covered with clothing, or similar materials,
as overheating can result in a fire risk! (E)

• This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved. Children
shall not play with the appliance. Cleaning
and user maintenance shall not be made by
children without supervision.

Place this drawing adjacent to the distribution board

OBS!
– do not restrict the thermal emission of the heated ceiling
– do not affix materials other than those recommended
– do not insert nails or screws

HP3N, 300W, 220-240V
HP6N, 600W, 220-240V

Drawing of the installation

Item no: 204773, 2017-11-28 HH/CH

Main offi ce

Frico AB Tel: [phone]
Box 102
SE-433 22 Partille [e-mail]
Sweden www.frico.se

For latest updated information and information
about your local contact: www.frico.se