MY-HITE CORNER
ADJUSTABLE
TABLE
Model Number : FCNAHB
Please Read Instructions Before Use
ASSEMBLY INSTRUCTIONS
FRIANT & AS SOC.
4901 E.12 S TREET OAK LAND, CA 94601
T:510.535.5113 · FAX:51 0.535.5237
www.Friant.com/system s/my-hite
»» Introduction
Friant offers a comprehensive line of office furniture for every space
and requirement, now including My-Hite, a height adjustable table
that allows for standing or sitting while working.
»» User»Notes
1. As with all power-operated products, please follow instructions
and handle with care.
2. When moving My-Hite tables, please lift the tables, do not drag
them.
3. Check that the load on the table does not exceed limits (220lbs
straight, 330lbs corner).
4. Table should be level and aligned at all times.
Thank you for choosing Friant. We appreciate the
trust and confidence you have placed in us and are
committed to providing you the best possible product.
When»placing»table»in»final»location,»be»sure»t here»is»ample»
room»for»adjustment»around»ALL»sides,»and»at»the»highest»
(50”)»and»lowest»(24.5”)»points»the»table»can»reach.»Make»
sure»table»will»not»come»into»contact»with»any»fixed»objects»
(fixed»tops,»storage,»shelv ing,»etc.)»while»adjusting.
Important:
»» »»Tools»Needed»
WARNING:
FAILURE»TO»FOLLOW»THE»ASSEMBLY»INSTRUCTIONS»IN»THIS»
MANUAL»CAN»RESULT»IN»PRODUCT»DAMAGE,»OR»PERSONAL»INJURY.
1 2
1. Read instructions
carefully. Check that
no parts are missing.
Single Sid ed
Wrench
Socket Head
Wrench
Electric Drill
Friant & Ass ociates , LLC does n ot assum e any respo nsibilit y for prod uct tha t is altered i n any way.
2. Carefully identify each
component, especially
those that are similar.
The most com mon
mistake is mixing
up the order a nd
placement of parts.
Tools Needed
PART# NAME PIECES
A Side Bracket 3
B Column Leg & Pad 3
C Crossbeam 3
D Center Rails 2
E Control Panel 1
F Control Box 1
G Telescopic Cover Plate 1
H Connector Wires 1 + 3
I Feet 3
J Socket Button Head Bolt
M6*20mm
12
K Socket Button Head Bolt
M6*12mm
20
L Wire Manager 4
M Truss Head Screw
M5*20mm
34
Parts List
Installation Steps
Step»1: Place worksurface finished
side down on a blanket.
Step»3a: Insert pad into B crossbeam.
Step»3b: Insert C column leg
into B crossbeam.
Step»2: Insert A side bracket into
B crossbeam assembly.
Repeat on other sides.
A
SIDE»BRACKET
C
COLUMN»LEG»
and»PAD
WORKSURFACE
B
CROSSBEAM
Installation Steps
J
SOCKET»BUTTON»
HEAD»BOLT»
M6*20mm
I
FOOT
Step»6a: Attach I feet to B column leg
with J 4 socket button head
bolts, M6*20mm.
Step»6b: Tighten bolts securely.
Step»7: Repeat step 6 with other two legs.
Step»4: Use 4 socket button head
bolts, M6*12mm to secure
side bracket, column leg and
crossbeam together as shown
in detail.
Step»5: Remove pad and repeat steps 3 & 4 with other two legs.
Installation Steps
Step»8: Place all 3 leg assemblies on worksurface and insert D center
rails into C crossbeams as shown. Hole on center rails should be
centered between crossbeams. Center leg assemblies on the
worksurface. Make sure your overhang is even on all three sides.
A
B
IMPORTANT:
MAKE»SURE»COLUMN»LEGS»ARE»SITTING»PERFECTLY»FLAT»AGAINST»
THE»WORKSURFACE
D
CENTER
RAILS
Base is: A - 40”-68”
B - 36”-54”
Maximum recommended top: 54”x78”
Minimum recommended top: 36”x40”
Installation Steps
Step»10: Ensure the leg assembly is still
centered, both side-to-side and
front-to-back. Secure the leg
assembly to the worksurface
with M 12 truss head screws
M5*20mm.
Step»11: Secure the side bracket to
the worksurface with M 12
truss head screws M5*20mm.
Step»9: Secure D center rails to
C crossbeams with K 8 socket
button head bolt M6*12mm.
Step»12: Secure the E control panel
in the desired location
with M 2 truss head
screws M5*20mm.
M
TRUSS»HEAD»
SCREWS»
M5*20mm
E
CONTROL»
PANEL
Installation Steps
Schematic view of the My-Hite wiring:
Step»13: Insert the F control box
in-between crossbeams.
F
CONTROL»
BOX
H
CONNECTOR
WIRES
Step»14: Connect E control panel to F control box
with H connector wires. Use L wire manager
to secure H connector wires to underside of
worksurface.
Make»sure»the»length»of»the»plug-in»cord»is»appropriate»to»both»reach»
the»outlet,»AND»for»the»distance»the»table»will»travel»up»and»down.»
Range:»24.5”»at»lowest»to»50”»highest.
Step»15: Install the G telescopic cover
plates, leaving exit space for the
electrical power cords, and secure
to worksurface with M 8 truss head
screws M5*20mm
Insure the length of
exposed power cord
is sufficient.
Step»16: Turn table right side up, adjust the glides as necessary, and plug the
power cord into a 110v outlet.
Step»17: It is important to perform the
reset operation below before
you use your My-Hite table
for the first time.
FIRST TIME USE:
SET MINIMUM HEIGHT
RESET OPERATION
CLEAR MAXIMUM & MINIMUM HEIGHT
SET MAXIMUM HEIGHT
1. Press the arrow up (V) button to get to desired minimum height. »
Note:»the»arrow»up»button»must»be»the»last»button»pressed»to»set»the»minimum»height.»You»
cannot»press»the»arrow»down»button»when»trying»to»set»the»minimum»height.
2. Hold “S” button til screen display flashes. Immediately press “S” button twice
again.
3. Display will flash “000” and then show the set minimum height.
1. Lower the table to 24.5” by holding arrow down (V) button. Release button.
2. Press the arrow down (V) button again and hold til ASR shows on the display.
3. Release the button and the ASR will flash on the display
4. Hold the arrow down button again. Table will shift up and down slightly as it
resets to 24.5”.
V
1. Press the arrow up ( ) button to get to desired maximum height. »
Note:»the»arrow»up»button»must»be»the»last»button»pressed»to»set»the»maximum»height.»
You»cannot»press»the»arrow»down»button»when»trying»to»set»the»maximum»height.
2. Hold “S” button til screen display flashes. Immediately press “S” button twice
again.
3. Display will flash “999” and then show the set maximum height.
1. Table can be at ANY HEIGHT but NOT the minimum or maximum.
2. Hold “S” til display flashes. Release button.
3. Press “S” slowly, multiple times - until “555” shows on display.
Note: Display will show other codes, continue to press “S” until “555” shows.
4. Display will then show table height and can now move to any height between
24.5” and 50.1”.
NOTE:»If»you»cannot»lower»the»table»to»the»24.5”»height»to»perform»reset»
operation,»you»may»need»to»clear»out»the»maximum»and»minimum»height»
(See»instructions»below).»Once»completed,»please»return»to»the»Reset»
Operation»instructions.
TROUBLESHOOTING MY-HITE
Error»code Explanation Cause Solution
H01 Motor has
overheated
Overuse 1. Let motor rest of 10 minutes
2. Perform reset operation
if problem persists
3. contact Friant customer service
ASR or
RST (solid
or flashing)
System is
locked
Various Reasons 1. Remove plug from electrical outlet for 15
seconds, then plug unit back in
2. Perform reset operation
if problem persists
3. contact Friant customer service to
replace control panel
No display Control
Panel has
lost power
Disruption in
power supply to
base
1. Remove plug from electrical outlet for 15
seconds, then plug unit back in
2. Perform reset operation
if problem persists
3. contact Friant customer service to
replace control panel
E01,
E02, or
E03
Excessive
weight
distribution
Too much
weight (limit
exceeded)
or
Other problem
1. Check that weight on table does not
exceed limit
2. Perform reset operation
if problem persists
3. contact Friant customer service to
replace control panel
E0 7,
E08, or
E09
Signal
Interruption
Signal is
interrupted
between leg
and computer
1. Perform reset operation
if problem persists
2. contact Friant customer service
Follow assembly instructions closely
Do not overload the tables (220 lbs maximum straight, 330 lbs maximum
corner)
The input voltage should be within 108-132V
Use the glides to properly level the table before use
When moving the table, do not tilt the table on one leg or misalignment may
occur
Before first use, perform reset operation
If, after trouble shooting the problem persists, contact Customer Service for
further assistance.
GENERAL TIPS
Loading...