Freud SD200 Series, SD300 Series, SD500 Series, SD600 Series Setup And Configuration Manual
DADO SETS
56
Dado Chipper Set-Up Guide
Dado Chipper Set-Up & Configuration Guide
These charts explain how to set up your dado cutters to achieve your desired width of cut. Complete
set-up instructions, safety information and technical specifications are contained in the manual that
comes in the dado set.
Set-Up For SD600 Series Dial-A-Width Dado Sets - Cuts Dadoes From 7/32" to 29/32"
Cut Width 7⁄32" 1⁄4" 9⁄32" 5⁄16" 11⁄32" 3⁄8" 13⁄32" 7⁄16" 15⁄32" 1⁄2" 17⁄32" 9⁄16" 19⁄32" 5⁄8" 21⁄32" 11⁄16" 23⁄32" 3⁄4" 25⁄32" 13⁄16" 27⁄32" 7⁄8" 29⁄32"
Left Outside Blade
Right Outside Blade
3/32" Chipper – – – – – – – – – – – –
1/8" Chipper – – – – – –
1/8" Chipper – – – – – – – – – –
1/8" Chipper – – – – – – – – – – – – – –
1/8" Chipper – – – – – – – – – – – – – – – – – –
*Number of Clicks 1 9 16 25 8 16 15 22 8 16 15 22 8 16 15 22 8 16 15 22 8 15 22
Set-Up For SD300 Series Dado Sets - Cuts Dadoes From 1/4" to 7/8"
Cut Width 7⁄32" 1⁄4" 9⁄32" 5⁄16" 11⁄32" 3⁄8" 13⁄32" 7⁄16" 15⁄32" 1⁄2" 17⁄32" 9⁄16" 19⁄32" 5⁄8" 21⁄32" 11⁄16" 23⁄32" 3⁄4" 25⁄32" 13⁄16" 27⁄32" 7⁄8" 29⁄32"
Left Outside Blade N/A N/A
Right Outside Blade N/A N/A
1/16" Chipper N/A – – – – – – – – – – N/A
1/8" Chipper N/A – – – – N/A
1/8" Chipper N/A – – – – – – – – N/A
1/8" Chipper N/A – – – – – – – – – – – – N/A
1/8" Chipper N/A – – – – – – – – – – – – – – – –
N/A
0.020" (0.5mm) Shim N/A – – – – – – – – – – N/A
0.012" (0.3mm) Shim N/A – – – – – – – – – – N/A
0.008" (0.2mm) Shim N/A – – – – – – – – – – – – – – – – – – – – N/A
0.004" (0.1mm) Shim N/A – – – – – – – – – – – – – – – – – – – – N/A
For ultimate precision and cut quality, this unique stacked dado system allows for quick and easy adjustments without the use of
shims–giving flawless flat bottom cuts in hardwoods, softwoods, veneered plywoods and laminates. This chart is applicable for the
SD606 and the SD608 Dial-A-Width dado sets.
The SD500 Super Dado series are available in 6"(SD506), 8"(SD508), 10"(SD510) and 12"(SD512). This series gives flawless flat bottom
grooves with virtually splinter-free cuts in hardwoods, softwoods, veneered plywoods and laminates. This chart is applicable for the SD506,
SD508, SD510 and SD512 dado sets.
The SD300 series gives superb cuts in softwoods & hardwoods. Available in 6"(SD306) and 8"(SD308) sizes. Cuts; hardwoods, softwoods, chipboard, plywood, & laminates. This chart is applicable for the SD306 amd SD308 dado sets.
* The clicks are from zero on a “zeroed-out” dial. To learn how to zero-out the SD600 series dial refer to the manual that is included with the SD600 series dado sets.
Always check the Table Saw manual or consult the manufacturer for the maximum allowable dado width.
Set-Up For SD500 Series Dado Sets - Cuts Dadoes From 1/4" to 29/32"
Cut Width 7⁄32" 1⁄4" 9⁄32" 5⁄16" 11⁄32" 3⁄8" 13⁄32" 7⁄16" 15⁄32" 1⁄2" 17⁄32" 9⁄16" 19⁄32" 5⁄8" 21⁄32" 11⁄16" 23⁄32" 3⁄4" 25⁄32" 13⁄16" 27⁄32" 7⁄8" 29⁄32"
Left Outside Blade N/A
Right Outside Blade N/A
1/16" Chipper N/A – – – – – – – – – – – –
3/32" Chipper N/A – – – – – – – – – – –
1/8" Chipper N/A – – – – –
1/8" Chipper N/A – – – – – – – – –
1/8" Chipper N/A – – – – – – – – – – – – –
1/8" Chipper N/A – – – – – – – – – – – – – – – – –
0.020" (0.5mm) Shim N/A – – – – – – – – – – – – – – – – – – – –
0.012" (0.3mm) Shim N/A – – – – – – – – – – – – – – – – – – – –
0.008" (0.2mm) Shim N/A – – – – – – – – – – – – – – – – – – – – – –
0.004" (0.1mm) Shim N/A – – – – – – – – – – – – – – – – – – – – – –
Symbol Key
Outer Blades
Chipper
Chipper
Shim
Spacer
DADO SETS
57
Dado Parts & Shims
Dado Chipper Set-Up & Configuration Guide
Use Dado Sets components only with the dado set for which they are designed. Never use chippers without both
outside blades. SS100 will work with any stacked dado set on table saws or radial arm saws with a 5/8" arbor. SS200
will work with any stacked dado on table saws or radial arm saws with a 1" arbor.
Freud dado sets are built to last through many years of sharpening and use. However, accidents like dropping a chipper
do happen and Freud offers a full range of replacement parts. All outside blades and chippers are made to the same
exacting standards of quality as the original set. For wider cuts Freud’s Precision Shim Set and additional chippers are
available.
SS100 5/8" 3-5/32" 4 2 2 2
SS200 1" 3-5/32" 4 2 2 2
Precision Shim Sets
Outside Number of Each Thickness
Item Arbor Dia. .004 .008 .012 .020
SD600SP Spring hub assembly brearing & screws
SD600BB Ball bearing for hub assembly
SD600HUB Dial hub
SD600FLG Flange for blade assembly
SD600BTI Threaded insert for flange
SD600ISC1 Screws for threaded insert
SD600FSC Screws for flange
Replacement Parts For SD606 & SD608 Series
Oustside Blades
Item For Dia. Teeth Arbor Orientation
SD206OLH SD206 6" 10 5/8" Left Side
SD206ORH SD206 6" 10 5/8" Right Side
SD208OLH SD208 8" 12 5/8" Left Side
SD208ORH SD208 8" 12 5/8" Right Side
SDOS06LH SD306 6" 24 5/8" Left Side
SDOS06RH SD306 6" 24 5/8" Right Side
SDOS08LH SD308 8" 24 5/8" Left Side
SDOS08RH SD308 8" 24 5/8" Right Side
SDOS10LH SD310 10" 36 1" Left Side
SDOS10RH SD310 10" 36 1" Right Side
SDOS12LH SD312 12" 36 1" Left Side
SDOS12RH SD312 12" 36 1" Right Side
SD506OLH SD506 6" 24 5/8" Left Side
SD506ORH SD506 6" 24 5/8" Right Side
SD508OLH SD508 8" 24 5/8" Left Side
SD508ORH SD508 8" 24 5/8" Right Side
SD510OLH SD510 10" 32 1" Left Side
SD510ORH SD510 10" 32 1" Right Side
SD512OLH SD512 12" 36 1" Left Side
SD512ORH SD512 12" 36 1" Right Side
SD606OLH SD606 6" 24 5/8" Left Side
SD606ORH SD606 6" 24 5/8" Right Side
SD608OLH SD608 8" 24 5/8" Left Side
SD608ORH SD608 8" 24 5/8" Rigth Side
Chippers
Item For Dia. Teeth Arbor Thickness
SD206C16 SD206 6" 2 5/8" 1/16"
SD206C18 SD206 6" 2 5/8" 1/8"
SD208C16 SD208 8" 2 5/8" 1/16"
SD208C18 SD208 8" 2 5/8" 1/8"
SDIC0616 SD306 6" 2 5/8" 1/16"
SDIC0618 SD306 6" 2 5/8" 1/8"
SDIC0816 SD308 8" 2 5/8" 1/16"
SDIC0818 SD308 8" 2 5/8" 1/8"
SDIC1016 SD310 10" 2 1" 1/16"
SDIC1018 SD310 10" 2 1" 1/8"
SDIC1216 SD312 12" 2 1" 1/16"
SDIC1218 SD312 12" 2 1" 1/8"
SD506C16 SD506 6" 4 5/8" 1/16"
SD506C332 SD506 6" 4 5/8" 3/32"
SD506C18 SD506 6" 4 5/8" 1/8"
SD508C16 SD508 8" 4 5/8" 1/16"
SD508C332 SD508 8" 4 5/8" 3/32"
SD508C18 SD508 8" 4 5/8" 1/8"
SD510C16 SD510 10" 4 1" 1/16"
SD510C332 SD510 10" 4 1" 3/32"
SD510C18 SD510 10" 4 1" 1/8"
SD512C16 SD512 12" 4 1" 1/16"
SD512C332 SD512 12" 4 1" 3/32"
SD512C18 SD512 12" 4 1" 1/8"
SD606C18 SD606 6" 4 5/8" 1/8"
SD606C332 SD606 8" 4 5/8" 3/32"
SD608C18 SD608 8" 4 5/8" 1/8"
SD608C332 SD608 8" 4 5/8" 3/32"
(Continued)
The SD200 series gives great performance at a great price. Available in 6"(SD206) and 8"(SD208). Cuts; hardwoods, softwoods,
chipboard, plywood, & laminates. This chart is applicable for both the SD206, & SD208 dado sets.
Dado Replacement Parts & Shim Sets
Set-Up For SD200 Series Dado Sets - Cuts Dadoes From 1/4" to 7/8"
Cut Width 7⁄32" 1⁄4" 9⁄32" 5⁄16" 11⁄32" 3⁄8" 13⁄32" 7⁄16" 15⁄32" 1⁄2" 17⁄32" 9⁄16" 19⁄32" 5⁄8" 21⁄32" 11⁄16" 23⁄32" 3⁄4" 25⁄32" 13⁄16" 27⁄32" 7⁄8" 29⁄32"
Left Outside Blade N/A N/A
Right Outside Blade N/A N/A
1/8" Chipper N/A – – N/A
1/8" Chipper N/A – – – – – – – – N/A
1/8" Chipper N/A – – – – – – – – – – – – N/A
1/16" Spacer N/A – – – – – – – – N/A
0.020" (0.5mm) Shim N/A – – – – – – – – – – N/A
0.012" (0.3mm) Shim N/A – – – – – – – – – – N/A
0.008" (0.2mm) Shim N/A – – – – – – – – – – – – – – – – – – – – N/A
0.004" (0.1mm) Shim N/A – – – – – – – – – – – – – – – – – – – – N/A
Loading...