French Fitness FF-X9LP ASSEMBLY MANUAL
FF-X9LP
Functional Multi Gym System w/Leg Press
ASSEMBLY MANUAL
FEATURES
2
•
•
•
•
with ease
•
bearings
•
TECH SPECS
• 190 lb Weight Stack
• Lat Pulldown: Feels like 280 lbs Due to pulley ratio
• Dimensions: 82"D x 91 "W x 83.9"H
WARRANTY
• Lifetime Parts and 1 Year Labor Warranty
NO
Name
QTY
NO
Name
QTY
1
Under Frame
43
Incline support Pollex Frame
2 Guide Road
44
M 12x75 outer hex bolt
3 Rubber Cushion
45
Pedal Board
4
Ф Washers
46
M 10x85 outer hex bolt
5
M10x20 outer hex bolt
47
Pulley 7
M8x50 outer hex bolt
48
Pulley Spacer
8 Flat washers
49
Steel wire rope
9
M8 Lock nuts
50
M 10x45 outer hex bolt
10
Lifting Rod
51
M 10x130 outer hex bolt
11
Top Plate
52
M 12x85 outer hex bolt
12
Cuts Iron Cooler Weight
54
Pulley weldment
13
Magnetic Pin
55
Transition Rope
14
Inclined Support beam
56
Link Chain
15
Adjustment boars
57
Butterfly arm Rope
16
Reset Poll Pin
58
M 10x15 outer hex bolt
17
Ф 12 Flat Washers
59
Backrest adjusting Board
18
M 12 Lock nuts
60
Cushion
19
M 12x70 hex bolts
61
Backrest tube Shaft
20
Upper beam
64
Foam tube
21
M 10x70 outer hex bolt
65
Foam Rod
23
M 10x60 hex bolts
66
Foam
24
Shield support frame
67
Inner end cup
25
M 10 lock nuts
68
Outer end cup
26
Decorative board
70
Shrauds
27
M 12x130 outer hex bolt
71
M 8x16 outer hex bolt
28
Seat supporting tube
72
Straight bar
29
Seat cushion adjustment tube
73
Lat bar
30
Kick rotation shaft
74
Hex reset poll pin
31
Foot hook bending tube
101
Poll strap
32
Pushing frame
103
Support board Left/Right
33
Front pushing arm
104
Low poll steel rope
34
Ф 16x137 Front connection shaft
105
Flat pedal chasis
35
Reset poll pin
106
Metallurgy sleeves
36
17x123 Pushing frame shaft
107
Seat cushion Board
38
Ф 10x30 Washers
108
Backrest adjusting tube
39
M 10x16 outer hex bolt
109
Ф 25x112 Shaft
40
M 12x20 outer hex bolt
110
Movable tube
41
Butterfly arm Left
120
M 10x35 outer hex bolt
42
Butterfly arm Right
121
10x30 Flat washers
122
Leg press board
3
Parts Diagram
4
41
30
103
43
1
35 7224
28
10
41 42
45
11
29
32
45
12
31
26
28
20
3436
10
43
48
65
70
101
54
14
56
105
109
73
60
72
107
64
2
106
33
59
66
Parts Diagram
5
75
27
46
52
4
17
58 71
67
50
19
39
68
40
21
120
9
23
44
51
18
13
47
49 55 57
Install ing S tep 1 Exploded View
6
2
4
3
1
4
5
7
Installation Instruction
1. Put Φ10 washer (4) over M10*20 outer hexagonal bolts (5), and fasten the guiding
rod assembly (2) to the underframe weldment (1).
2. Install the cushion (3) on the guiding rod assembly (2)
Note: The outer hexagonal bolts need to be tightened
Installing Step 2 Exploded View
8
2
11
10
11
13
12
Install ing Step 2 After Installation
9
Installation Instruction
1. Place 11 PCS cast iron counterweight lowerpiece (12) and cast iron counterweight top piece (11)
in sequence on the upper end of the guiding rod assembly (2).
2. Insert the lifting rod (10) and the cast iron counterweight lower piece (12)and the cast iron
counterweight top piece (11) together, and install the positioning bolts on the cast iron
counterweight top piece (11).
3. Insert the magnetic pin (13) on the cast iron counterweight lower piece (12) and
the lifting rod (10).
4. Fasten the counterweight limit block (6) to the guiding rod assembly with M8*50 outer
hexagonal bolts (7), at washers (8), and M8 lock nuts (9).
Note: The outer hexagonal bolts need to be tightened.
Installing Step 3 Exploded View
10
17
15
14
15
16
18
17
19
18
17
17
40
17
Installing Step 3 After Installation
11
Installation Instruction
1. Fasten the inclined support beam (14) to the chassis assembly with 12*70 outer
hexagonal bolts (19), 12 at washers (17), and M12 lock nuts (18).
2. Use 12*20 outer hexagonal bolts (40) and 12 at washers (17) to x the inclined
support beam adjustment board (15).
3. Fix the reset pull pin (16) on the inclined support beam adjustment board (15).
Note: The outer hexagonal bolts need to be tightened
Install ing Step 4 Exploded View
12
23
5
19
17
20
13
17
23
14
24
18
14
17
4
13
Installation Instruction
1. Fix the shield suppor tframe (24) and the upper beam (20) together with M10*60
outer hexagonal bolts (23), Φ10 washers (4) and M10 lock nuts (25)
2. Connect the upper beam (20) and the guiding rod (2) together, and fasten them
with M10*20 outer hexagonal bolts (5), Φ10 washers (4) M10 lock nuts (25).
3. Fasten the upper beam (20) to the inclined support beam (14) with M12*70 outer
hexagonal bolts (19), M2 washers (17), and M12 lock nuts (18)
Note: The outer hexagonal bolts need to be tightened
Installing S tep 5 Exploded View
14
18
17
17
15
26
16
26
17
17
27
Installing Step 5 After Installation
15
Installation Instruction
1. Use M12*130 outer hexagonal bolts (27), Φ12 washers (17) and M12 lock nuts(18)
to fasten the decorative board (26) to the upper beam and theinclined support
beam assembly.
Note: The hexagon bolt sneed to be tightened
Installing Step 6 Exploded View
16
29
17
30
72
20
5
4
18
19
19
31
4
5
18
28
17
Loading...