FREI MAX 691 ACSE Datasheet

General Description

The MAX691A/MAX693A/MAX800L/MAX800M micro­processor (µP) supervisory circuits are pin-compatible
upgrades to the MAX691, MAX693, and MAX695. They
improve performance with 30µA supply current, 200ms
typ reset active delay on power-up, and 6ns chip­enable propagation delay. Features include write pro­tection of CMOS RAM or EEPROM, separate watchdog
outputs, backup-battery switchover, and a RESET out-
put that is valid with V

CC

down to 1V. The MAX691A/
MAX800L have a 4.65V typical reset-threshold voltage,
and the MAX693A/MAX800Ms’ reset threshold is 4.4V
typical. The MAX800L/MAX800M guarantee power-fail
accuracies to ±2%.

________________________Applications

Computers

Controllers

Intelligent Instruments

Automotive Systems

Critical µP Power Monitoring

____________________________Features

o 200ms Power-OK/Reset Timeout Period

o 1µA Standby Current, 30µA Operating Current

o On-Board Gating of Chip-Enable Signals,

10ns max Delay

o MaxCap

®

or SuperCap Compatible

o Guaranteed

RREESSEETT

Assertion to V

CC

= +1V

o Voltage Monitor for Power-Fail or Low-Battery

Warning

o Power-Fail Accuracy Guaranteed to ±2%

(MAX800L/M)

o Available in 16-Pin Narrow SO, Plastic

DIP, and TSSOP Packages

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

________________________________________________________________

Maxim Integrated Products

1

Pin Configuration

MAX691A
MAX693A
MAX800L

MAX800M

V

OUT

VCCBATT ON

CE OUT

CE IN

WDI

PFO

RESET

VBATT

PFI

GND

OSC IN

OSC SEL

1

9

4

7

8

ADDRESS

DECODE

AUDIBLE

ALARM

5V

REGULATOR

+8V

0.1μF

CMOS RAM

2

12

11

10

15

13

5

3

A0-A15

I/O

NMI

RESET

μP

LOW LINE WDO

SYSTEM STATUS INDICATORS

NO

CONNECTION

0.47F*

1N4148

*MaxCap

614

Typical Operating Circuit

19-0094; Rev 11; 8/08

MaxCap is a registered trademark of Kanthal Globar, Inc.

Ordering Information continued on last page.

*

Dice are specified at TA= +25°C, DC parameters only.

Devices in PDIP, SO, and TSSOP packages are available in both
leaded and lead-free packaging. Specify lead free by adding
the + symbol at the end of the part number when ordering.
Lead free not available for CERDIP package.

For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.

Ordering Information

PART TEMP RANGE

MAX691ACUE -0°C to +70°C 16 TSSOP

MAX691ACSE -0°C to +70°C 16 Narrow SO

MAX691ACWE -0°C to +70°C 16 Wide SO

MAX691ACPE -0°C to +70°C 16 Plastic DIP

MAX691AC/D -0°C to +70°C Dice*

MAX691AEUE -0°C to +70°C 16 TSSOP

MAX691AESE -40°C to +85°C 16 Narrow SO

MAX691AEWE -40°C to +85°C 16 Wide SO

MAX691AEPE -40°C to +85°C 16 Plastic DIP

PIN ­PA C K A G E

TOP VIEW

VBATT

V

OUT

V

GND

BATT ON

LOW LINE

OSC IN

OSC SEL

1

2

CC

3

4

5

6

7

8

DIP/SO/TSSOP

RESET

16

RESET

15

WDO

14

MAX691A
MAX693A
MAX800L
MAX800M

CE IN

13

CE OUT

12

WDI

11

PFO

10

PFI

9

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

2 _______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL CHARACTERISTICS

(MAX691A, MAX800L: VCC= +4.75V to +5.5V; MAX693A, MAX800M: VCC= +4.5V to +5.5V; VBATT = 2.8V, TA= T

MIN

to T

MAX

,

unless otherwise noted.)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.

Terminal Voltage (with respect to GND)

V

CC

.......................................................................-0.3V to +6V

VBATT...................................................................-0.3V to +6V

All Other Inputs .....................................-0.3V to (V

OUT

+ 0.3V)

Input Current

V

CC

Peak...........................................................................1.0A

V

CC

Continuous.............................................................250mA

VBATT Peak ..................................................................250mA

VBATT Continuous ..........................................................25mA

GND, BATT ON .............................................................100mA

All Other Outputs ............................................................25mA

Continuous Power Dissipation (T

A

= +70°C)

TSSOP (derate 6.70mW/°C above +70°C) ..................533mW

Narrow SO (derate 8.70mW/°C above +70°C) ...........696mW

Wide SO (derate 9.52mW/°C above +70°C)...............762mW

Plastic DIP (derate 10.53mW/°C above +70°C) ..........842mW

CERDIP (derate 10.00mW/°C above +70°C)..............800mW

Operating Temperature Ranges

MAX69_AC_ _/MAX800_C_ _ .............................0°C to +70°C

MAX69_AE_ _/MAX800_E_ _ ...........................-40°C to +85°C

MAX69_AMJE ................................................-55°C to +125°C

Storage Temperature Range .............................-65°C to +160°C

Lead Temperature (soldering, 10s) .................................+300°C

VBATT - 0.15

MAX69_AC, MAX800_C 0.8 1.2

VBATT = 4.5V, I

OUT

= 20mA

µA

-1.0 0.02

VBATT + 0.2V ≤ V

CC

VBATT Standby Current
(Note 3)

-0.1 0.02

µA

5

VCC< VBATT - 1.2V,
VBATT = 2.8V

Supply Current in
Battery-Backup Mode
(excludes I

OUT

) (Note 2)

VBATT = 2.8V, I

OUT

= 10mA

V0 5.5

CONDITIONS

Operating Voltage Range,
V

CC

, VBATT (Note 1)

VBATT = 4.5V

0.04 1

µA30 100

Supply Current in
Normal Operating Mode
(excludes I

OUT

)

V

V

OUT

in Battery-Backup

Mode

VBATT - 0.25

VBATT = 2.8V

Ω

30

VBATT - 0.3

VBATT-to-V

OUT

On-Resistance

UNITSMIN TYP MAXPARAMETER

25

TA= +25°C

VCC> VBATT - 1V

TA= T

MIN

+ T

MIN

VBATT = 2.0V, I

OUT

= 5mA

TA= +25°C

TA= T

MIN

+ T

MIN

15

VBATT = 2.0V

VCC= 4.5V

I

OUT

= 250mA

VCC- 0.02 VCC- 0.05I

OUT

= 25mA

MAX69_AC/AE,
MAX800_C/E

I

OUT

= 210mA

VCC- 0.2 VCC- 0.35

VCC- 0.2 VCC- 0.3

V

VCC- 0.40

VCC- 0.17 VCC- 0.3V

V

OUT

Output

MAX69_AE,
MAX800_C/E

MAX69_AC

MAX69_A/M

MAX69_AE, MAX800_E 0.8 1.4

MAX69_A/M 0.8 1.6

ΩVCC= 4.5VVCC-to-V

OUT

On-Resistance

V

VBATT - 0.3

Power-up

Battery Switchover
Threshold

VBATT + 0.3

Power-down

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

_______________________________________________________________________________________ 3

MAX691A, MAX800L

mA720

–
RESET Output Short-Circuit

Current

V

3.5

RESET Output Voltage

0.1 0.4

0.004 0.3

ns100

Minimum Watchdog Input
Pulse Width

Clock

Cycles

1024

Watchdog Timeout Period,
External Clock (Note 4)

4096

ms70 100 140

Watchdog Timeout Period,
Internal Oscillator

1.0 1.6 2.25

Clock

Cycles

2048

Reset Active Timeout Period,
External Clock (Note 4)

ms140 200 280

Reset Active Timeout Period,
Internal Oscillator

ns800

LOW LINE-to-RESET Delay

µs80VCCto RESET Delay

MAX693A, MAX800M

CONDITIONS

mV15Reset Threshold Hysteresis

V

4.30 4.45

Reset Threshold Voltage

4.55 4.70

4.25 4.40 4.50

4.50 4.65 4.75

UNITSMIN TYP MAXPARAMETER

Output source current

I

SOURCE

= 1.6mA, VCC= 5V

I

SINK

= 3.2mA, VCC= 4.25V

I

SINK

= 50µA, VCC= 1V, VBATT = 0V, VCCfalling

VIL= 0.8V, VIH= 0.75 x V

CC

Short period

Long period

Short period

Long period

MAX800M, TA= +25°C, VCCfalling

Power-up

Power-up

MAX800L, TA= +25°C, VCCfalling

Power-down

ELECTRICAL CHARACTERISTICS (continued)

(MAX691A, MAX800L: VCC= +4.75V to +5.5V; MAX693A, MAX800M: VCC= +4.5V to +5.5V; VBATT = 2.8V, TA= T

MIN

to T

MAX

,

unless otherwise noted.)

RESET Output Voltage Low
(Note 5)

I

SINK

= 3.2mA 0.1 0.4 V

I

SINK

= 3.2mA, VCC= 4.25V 0.4

LOW LINE Output Voltage

I

SOURCE

= 1µA, VCC= 5V 3.5

V

LOW LINE Output
Short-Circuit Current

Output source current 1 15 100 µA

I

SINK

= 3.2mA 0.4

WDO Output Voltage

I

SOURCE

= 500µA, VCC= 5V 3.5

V

WDO Output
Short-Circuit Current

Output source current 310mA

V

IH

0.75 x V

CC

WDI Threshold Voltage
(Note 6)

V

IL

0.8

V

WDI = 0V -50 -10

WDI Input Current

WDI = V

OUT

20 50

µA

sec

mV60

Battery Switchover
Hysteresis

I

SINK

= 25mA

V

0.7 1.5

BATT ON Output
Low Voltage

I

SINK

= 3.2mA 0.1 0.4

Source current µA1 15 100

BATT ON Output
Short-Circuit Current

Sink current mA60

RESET AND WATCHDOG TIMER

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

4 _______________________________________________________________________________________

MAX69_AC/AE/AM, VCC= 5V

µA0.10 ±5OSC IN Leakage Current

µs12

RESET-to-CE OUT Delay

2.7

CE OUT Output-Voltage High
(Reset Active)

3.5

ns610

CE IN-to-CE OUT Propagation
Delay (Note 8)

mA0.1 0.75 2.0

CE OUT Short-Circuit Current
(Reset Active)

Ω75 150

CE IN-to-CE OUT Resistance
(Note 7)

µA±0.005 ±1

CE IN Leakage Current

60

PFI-to-PFO Delay µs

25

µA1 15 100

PFO Output Short-Circuit
Current

MAX800_C/E, VCC= 5V

CONDITIONS

3.5

PFO Output Voltage

V

0.4

nA±0.01 ±25PFI Leakage Current

1.225 1.25 1.275

PFI Input Threshold V

1.2 1.25 1.3

UNITSMIN TYP MAXPARAMETER

OSC SEL = 0V

Power-down

VCC= 0V, VBATT = 2.8V, I

OUT

= 1µA

VCC= 5V, I

OUT

= -100µA

50Ω source impedance driver, C

LOAD

= 50pF

Disable mode, –CE OUT = 0V

Enable mode

Disable mode

I

SOURCE

= 1µA, VCC= 5V

I

SINK

= 3.2mA

VIN= 20mV, VOD= 15mV

VIN= -20mV, VOD= 15mV

Output source current

Note 1: Either VCCor VBATT can go to 0V, if the other is greater than 2.0V.
Note 2: The supply current drawn by the MAX691A/MAX800L/MAX800M from the battery excluding I

OUT

typically goes to 10µA

when (VBATT - 1V) < V

CC

< VBATT. In most applications, this is a brief period as VCCfalls through this region.

Note 3: “+” = battery-discharging current, “--” = battery-charging current.
Note 4: Although presented as typical values, the number of clock cycles for the reset and watchdog timeout periods are fixed and

do not vary with process or temperature.

Note 5: RESET is an open-drain output and sinks current only.
Note 6: WDI is internally connected to a voltage divider between V

OUT

and GND. If unconnected, WDI is driven to 1.6V (typ),

disabling the watchdog function.

Note 7: The chip-enable resistance is tested with V

CC

= +4.75V for the MAX691A/MAX800L and VCC= +4.5V for the

MAX693A/MAX800M. CE IN = CE OUT = VCC/2.

Note 8: The chip-enable propagation delay is measured from the 50% point at CE IN to the 50% point at CE OUT.

ELECTRICAL CHARACTERISTICS (continued)

(MAX691A, MAX800L: VCC= +4.75V to +5.5V; MAX693A, MAX800M: VCC= +4.5V to +5.5V; VBATT = 2.8V, TA= T

MIN

to T

MAX

,

unless otherwise noted.)

kHz50OSC IN Frequency Range

µA10 100OSC SEL Input Pullup Current

µA10 100OSC IN Input Pullup Current

OSC SEL = 0V

OSC SEL = 0V

OSC SEL = V

OUT

or floating, OSC IN = 0V

V

V

OUT

- 0.3 V

OUT

- 0.6V

IH

3.65 2.00

OSC IN External Oscillator
Threshold Voltage

V

IL

kHz100

OSC IN Frequency with
External Capacitor

OSC SEL = 0V, COSC = 47pF

V

POWER-FAIL COMPARATOR

CHIP-ENABLE GATING

INTERNAL OSCILLATOR

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

_______________________________________________________________________________________

5

RESET

DELAY

(ms)

__________________________________________Typical Operating Characteristics

(TA = +25°C, unless otherwise noted.)

VCC SUPPLY CURRENT

vs. TEMPERATURE

(NORMAL OPERATING MODE)

36

VCC = 5V
VBATT = 2.8V
PFI, CE IN = 0V

34

32

30

SUPPLY CURRENT (μA)

CC

V

28

26

-60 120 150

-30 0 90

VBATT to V

20

VBATT = 2.0V

15

30

60

TEMPERATURE (°C)

ON-RESISTANCE

OUT

vs. TEMPERATURE

MAX691A TOC-01

BATTERY SUPPLY CURRENT (μA)

MAX691A TOC-04

BATTERY SUPPLY CURRENT

vs. TEMPERATURE

(BATTERY-BACKUP MODE)

2

VCC = 5V
VBATT = 2.8V
NO LOAD

1.5

1

0.5

0

-30 0 90

-60 120 150
TEMPERATURE (°C)

V

to V

CC

1.2

1.1

1.0

VCC = 5V,
VBATT = 0V

vs. TEMPERATURE

60

30

ON-RESISTANCE

OUT

MAX691A TOC-02

MAX691A TOC-05

CHIP-ENABLE ON-RESISTANCE

vs. TEMPERATURE

120

= 4.75V

V

CC

VBATT = 2.8V

= VCC/2

V

CE IN

100

80

CE ON-RESISTANCE (Ω)

60

40

-30 0 90

-60 120 150 180

60

30

TEMPERATURE (°C)

PFI THRESHOLD

vs. TEMPERATURE

1.50

1.25

1.00

MAX691A TOC-03

MAX691A TOC-06

VBATT = 2.8V

ON-RESISTANCE (Ω)

OUT

10

VBATT = 4.5V

VBATT-to-V

5

-60 120 150

-30 0 90
TEMPERATURE (°C)

60

30

RESET THRESHOLD
vs. TEMPERATURE

4.75
VBATT = 2.8V

4.70

4.65

MAX691A

4.60

MAX800L

4.55

4.50

4.45

RESET THRESHOLD (V)

4.40

MAX693A

4.35

MAX800M

4.30

-60 120 150

-30 0 90
TEMPERATURE (°C)

60

30

0.9

ON-RESISTANCE (Ω)

OUT

0.8

-to-V

CC

V

0.7

= 0V

V

CC

0.6

-60 120 150

-30 0 90

30

60

TEMPERATURE (°C)

RESET OUTPUT RESISTANCE

vs. TEMPERATURE

600

MAX691A TOC-07

500

VCC = 5V, VBATT = 2.8V
SOURCING CURRENT

400

300

200

RESET OUTPUT RESISTANCE (Ω)

100

VCC = 0V, VBATT = 2.8V
SINKING CURRENT

0

-30 0 90

-60 120 150
TEMPERATURE (°C)

60

30

PFI THRESHOLD (V)

MAX691A TOC-08

0.75

0.50

30

VCC = +5V,
VBATT = 0V
NO LOAD ON PFO

60

0.25

0

-60 120 150

-30 0 90
TEMPERATURE (°C)

RESET DELAY

vs. TEMPERATURE

230

= 0V TO 5V STEP

V

CC

VBATT = 2.8V

220

210

200

190

180

170

-60 120 150

-30 0 90

30

60

TEMPERATURE (°C)

MAX691A TOC-09

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

6 _______________________________________________________________________________________

____________________________Typical Operating Characteristics (continued)

(TA = +25°C, unless otherwise noted.)

20

0

0

BATTERY CURRENT

vs. INPUT SUPPLY VOLTAGE

16

MAX691A TOC-10

VCC (V)

I

BATT

(μA)

3

8

4

12 5

12

4

VBATT = 2.8V

I

OUT

= 0A

100

0.1

WATCHDOG AND RESET TIMEOUT PERIOD

vs. OSC IN TIMING CAPACITOR (COSC)

10

MAX691A TOC-11

COSC (pF)

WATCHDOG AND RESET TIMEOUT PERIOD (sec)

100

1

10 1000

VCC = 5V
VBATT = 2.8V

LONG WATCHDOG
TIMEOUT PERIOD

SHORT WATCHDOG
TIMEOUT PERIOD

RESET ACTIVE
TIMEOUT PERIOD

0 300

CHIP-ENABLE PROPAGATION DELAY

vs. CE OUT LOAD CAPACITANCE

MAX691A TOC-12

C

LOAD

(pF)

PROPAGATION DELAY (ns)

150

8

0

50 100 250

16

20

4

12

200

V

CC

= 5V
CE IN = 0V
TO 5V
DRIVER SOURCE

1000

1

1

V

CC

to V

OUT

vs. OUTPUT CURRENT

(NORMAL OPERATING MODE)

100

MAX691A TOC-13

I

OUT

(mA)

V

CC

to V

OUT

(mV)

100

10

10 1000

VCC = 4.5V
VBATT = 0V

SLOPE = 0.8

Ω

1000

1

VBATT to V

OUT

vs. OUTPUT CURRENT

(BATTERY-BACKUP MODE)

100

MAX691A TOC-14

I

OUT

(mA)

VBATT to V

OUT

(mV)

10

10

1100

VCC = 0V
VBATT = 4.5V

SLOPE = 8

Ω

LO

VCC to LOW LINE

AND CE OUT DELAY

MAX691A TOC-15

LOW LINE

5V

V

CC

RESET

THRESHOLD

LO

HI

HI

HI

LO

CE OUT

RESET

12μs

800ns

80μs

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

_______________________________________________________________________________________ 7

______________________________________________________________Pin Description

NAME FUNCTION

1 VBATT

Battery-Backup Input. Connect to external battery or capacitor and charging circuit. If backup battery is not
used, connect to GND.

2 V

OUT

Output Supply Voltage. When VCCis greater than VBATT and above the reset threshold, V

OUT

connects to

VCC. When VCCfalls below VBATT and is below the reset threshold, V

OUT

connects to VBATT. Connect a 0.1µF

capacitor from V

OUT

to GND. Connect V

OUT

to VCCif no backup battery is used.

PIN

3 V

CC Input Supply Voltage, 5V Input.

4 GND

Ground. 0V reference for all signals.

8 OSC SEL

Oscillator Select. When OSC SEL is unconnected or driven high, the internal oscillator sets the reset delay and
watchdog timeout period. When OSC SEL is low, the external oscillator input (OSC IN) is enabled (Table 1).
OSC SEL has a 10µA internal pull-up.

7 OSC IN

External Oscillator Input. When OSC SEL is unconnected or driven high, a 10µA pull-up connects from V

OUT

to
OSC IN, the internal oscillator sets the reset and watchdog timeout periods, and OSC IN selects between fast
and slow watchdog timeout periods. When OSC SEL is driven low, the reset and watchdog timeout periods may
be set either by a capacitor from OSC IN to ground or by an external clock at OSC IN (Figure 3).

6

LOW LINE

LOW LINE output goes low when VCCfalls below the reset threshold. It returns high as soon as VCCrises above

the reset threshold.

5 BATT ON

Battery-On Output. When V

OUT

switches to VBATT, BATT ON goes high. When V

OUT

switches to V

CC,

BATT ON

goes low. Connect the base of a PNP through a current-limiting resistor to BATT ON for V

OUT

current require-

ments greater than 250mA.

13

CE IN

Chip-Enable Input. The input to chip-enable gating circuit. If CE IN is not used, connect CE IN to GND or V

OUT.

12

CE OUT

Chip-Enable Output. CE OUT goes low only when CE IN is low and VCCis above the reset threshold. If CE IN is
low when reset is asserted, CE OUT will stay low for 15µs or until CE IN goes high, whichever occurs first.

11 WDI

Watchdog Input. WDI is a three-level input. If WDI remains either high or low for longer than the watchdog time­out period, WDO goes low and reset is asserted for the reset timeout period. WDO remains low until the next tran­sition at WDI. Leaving WDI unconnected disables the watchdog function. WDI connects to an internal voltage
divider between V

OUT

and GND, which sets it to mid-supply when left unconnected.

10

PFO

Power-Fail Output. This is the output of the power-fail comparator. PFO goes low when PFI is less than 1.25V.
This is an uncommitted comparator, and has no effect on any other internal circuitry.

9 PFI

Power-Fail Input. This is the noninverting input to the power-fail comparator. When PFI is less than 1.25V, PFO
goes low. When PFI is not used, connect PFI to GND or V

OUT

.

16 RESET

RESET is an active-high output. It is open drain, and the inverse of RESET.

15

RESET

RESET Output goes low whenever VCCfalls below the reset threshold. RESET will remain low typically for

200ms after V

CC

crosses the reset threshold on power-up.

14

WDO

Watchdog Output. If WDI remains high or low longer than the watchdog timeout period, WDO goes low and reset
is asserted for the reset timeout period. WDO returns high on the next transition at WDI. WDO remains high if
WDI is unconnected.

_______________Detailed Description

–R—E—S—E—T–

and RESET Outputs

The MAX691A/MAX693A/MAX800L/MAX800M’s RESET
and RESET outputs ensure that the µP (with reset
inputs asserted either high or low) powers up in a
known state, and prevents code-execution errors dur­ing power-down or brownout conditions.

The RESET output is active low, and typically sinks

3.2mA at 0.1V saturation voltage in its active state.
When deasserted, –RESET sources 1.6mA at typically
V

OUT

- 0.5V. RESET output is open drain, active high,

and typically sinks 3.2mA with a saturation voltage of

0.1V. When no backup battery is used, RESET output is

guaranteed to be valid down to V

CC

= 1V, and an

external 10kΩ pulldown resistor on RESET insures that
it will be valid with VCCdown to GND (Figure 1). As
VCCgoes below 1V, the gate drive to the RESET output
switch reduces accordingly, increasing the R

DS(ON)

and the saturation voltage. The 10kΩ pulldown resistor
insures the parallel combination of switch plus resistor
is around 10kΩ and the output saturation voltage is
below 0.4V while sinking 40µA. When using a 10kΩ
external pulldown resistor, the high state for
RESET output with VCC= 4.75V will be 4.5V typical.
For battery voltages ≥ 2V connected to VBATT, RESET
and RESET remain valid for V

CC

from 0V to 5.5V.

MAX691A/MAX693A/MAX800L/MAX800M

RESET and RESET are asserted when VCCfalls below
the reset threshold (4.65V for the MAX691A/MAX800L,

4.4V for the MAX693A/MAX800M) and remain asserted
for 200ms typ after V

CC

rises above the reset threshold
on power-up (Figure 5). The devices’ battery­switchover comparator does not affect reset assertion.
However, both reset outputs are asserted in battery­backup mode since VCCmust be below the reset
threshold to enter this mode.

Watchdog Function

The watchdog monitors µP activity via the Watchdog
Input (WDI). If the µP becomes inactive, RESET and
RESET are asserted. To use the watchdog function,
connect WDI to a bus line or µP I/O line. If WDI
remains high or low for longer than the watchdog time­out period (1.6s nominal), WDO, RESET, and RESET
are asserted (see

RESET and RESET Outputs

section,

and the

Watchdog Output

discussion on this page).

Watchdog Input

A change of state (high to low, low to high, or a mini­mum 100ns pulse) at the WDI during the watchdog
period resets the watchdog timer. The watchdog
default timeout is 1.6s.

To disable the watchdog function, leave WDI floating.
An internal resistor network (100kΩ equivalent imped­ance at WDI) biases WDI to approximately 1.6V.
Internal comparators detect this level and disable the
watchdog timer. When VCCis below the reset thresh­old, the watchdog function is disabled and WDI is dis­connected from its internal resistor network, thus
becoming high impedance.

Watchdog Output

The Watchdog Output (WDO) remains high if there is a
transition or pulse at WDI during the watchdog timeout
period. The watchdog function is disabled and –WDO is
a logic high when VCCis below the reset threshold, bat­tery-backup mode is enabled, or WDI is an open circuit.
In watchdog mode, if no transition occurs at WDI during
the watchdog timeout period, RESET and RESET are
asserted for the reset timeout period (200ms typical).
WDO goes low and remains low until the next transition
at WDI (Figure 2). If WDI is held high or low indefinitely,
RESET and RESET will generate 200ms pulses every

1.6s. WDO has a 2 x TTL output characteristic.

Selecting an Alternative

Watchdog and Reset Timeout Period

The OSC SEL and OSC IN inputs control the watchdog
and reset timeout periods. Floating OSC SEL and OSC
IN or tying them both to V

OUT

selects the nominal 1.6s
watchdog timeout period and 200ms reset timeout peri­od. Connecting OSC IN to GND and floating or connect­ing OSC SEL to V

OUT

selects the 100ms normal
watchdog timeout delay and 1.6s delay immediately
after reset. The reset timeout delay remains 200ms
(Figure 2). Select alternative timeout periods by con­necting OSC SEL to GND and connecting a capacitor
between OSC IN and GND, or by externally driving OSC
IN (Table 1 and Figure 3). OSC IN is internally connect­ed to a ±100nA (typ) current source that charges and
discharges the timing capacitor to create the oscillator
frequency, which sets the reset and watchdog timeout
periods (see

Connecting a Timing Capacitor at OSC IN

in the

Applications Information

section).

Microprocessor Supervisory Circuits

8 _______________________________________________________________________________________

Figure 1. Adding an external pulldown resistor ensures
–R—E—S—E—T–

is valid with V

CC

down to GND.

Figure 2. Watchdog Timeout Period and Reset Active Time

WDI

15

RESET

TO μP RESET

WDO

MAX691A
MAX693A

1kΩ

t

2

RESET t

t1 = RESET TIMEOUT PERIOD

= NORMAL WATCHDOG TIMEOUT PERIOD

t

2

= WATCHDOG TIMEOUT PERIOD IMMEDIATELY AFTER RESET

t

3

1

t

1

t

3

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

_______________________________________________________________________________________ 9

Chip-Enable Signal Gating

The MAX691A/MAX693A/MAX800L/MAX800M provide
internal gating of chip-enable (CE) signals to prevent
erroneous data from being written to CMOS RAM in the
event of a power failure. During normal operation, the
CE gate is enabled and passes all CE transitions. When
reset is asserted, this path becomes disabled, prevent­ing erroneous data from corrupting the CMOS RAM. All
these parts use a series transmission gate from –CE IN to
CE OUT (Figure 4).

The 10ns max CE propagation delay from CE IN to CE
OUT enables the parts to be used with most µPs.

Chip-Enable Input

The Chip-Enable Input (CE IN) is high impedance (dis­abled mode) while RESET and RESET are asserted.

During a power-down sequence where VCCfalls below
the reset threshold or a watchdog fault, –CE IN assumes
a high-impedance state when the voltage at CE IN
goes high or 15µs after reset is asserted, whichever
occurs first (Figure 5).

During a power-up sequence, CE IN remains high
impedance, regardless of CE IN activity, until reset is
deasserted following the reset timeout period.

In the high-impedance mode, the leakage currents into
this terminal are ±1µA max over temperature. In the
low-impedance mode, the impedance of –CE IN appears
as a 75Ω resistor in series with the load at CE OUT.

The propagation delay through the CE transmission
gate depends on both the source impedance of the
drive to –CE IN and the capacitive loading on the Chip­Enable Output (–CE OUT) (see Chip-Enable Propagation
Delay vs. CE OUT Load Capacitance in the

Typical

Operating Characteristics

). The CE propagation delay
is production tested from the 50% point of –CE IN to the
50% point of –CE OUT using a 50Ω driver and 50pF of
load capacitance (Figure 6). For minimum propagation
delay, minimize the capacitive load at CE OUT, and
use a low output-impedance driver.

Chip-Enable Output

In the enabled mode, the impedance of CE OUT is
equivalent to 75Ω in series with the source driving CE
IN. In the disabled mode, the 75Ω transmission gate is
off and CE OUT is actively pulled to V

OUT

. This source

turns off when the transmission gate is enabled.

–L—O—W——L—I—N—E–

Output

LOW LINE is the buffered output of the reset threshold
comparator. LOW LINE typically sinks 3.2mA at 0.1V.
For normal operation (VCCabove the LOW LINE thresh­old), LOW LINE is pulled to V

OUT

.

Power-Fail Comparator

The power-fail comparator is an uncommitted comparator
that has no effect on the other functions of the IC.
Common uses include low-battery indication (Figure 7),
and early power-fail warning (see

Typical Operating

Circuit

).

Power-Fail Input

Power-Fail Input (PFI) is the input to the power-fail com­parator. It has a guaranteed input leakage of ±25nA
max over temperature. The typical comparator delay is
25µs from VILto VOL(power failing), and 60µs from V

IH

to VOH(power being restored). If PFI is not used, con­nect it to ground.

Figure 3. Oscillator Circuits

Watchdog Timeout Period

OSC SEL OSC IN

Normal Immediately After Reset

Reset Timeout Period

Low External Clock Input 1024 clks 4096 clks 2048 clks

Low External Capacitor (600/47pF x C)ms (2.4/47pF x C)sec (1200/47pF x C)ms

Floating Low 100ms 1.6s 200ms

Floating Floating 1.6s 1.6s 200ms

Table 1. Reset Pulse Width and Watchdog Timeout Selections

EXTERNAL

OSCILLATOR

8

OSC SEL

7

OSC IN

MAX691A
MAX693A
MAX800L

MAX800M

50kHz

8

7

EXTERNAL

CLOCK

OSC SEL

OSC IN

INTERNAL OSCILLATOR

1.6s WATCHDOG

8

7

OSC SEL

OSC IN

N.C. N.C.

N.C.

INTERNAL OSCILLATOR

100ms WATCHDOG

8

OSC SEL

7

OSC IN

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

10 ______________________________________________________________________________________

Figure 4. MAX691A/MAX693A/MAX800L/MAX800M Block Diagram

Figure 5. Reset and Chip-Enable Timing

5

BATT ON

4.65V*

3

V

CC

1

VBATT

13

CE IN

MAX691A
MAX693A
MAX800L

7

OSC IN

WDI

PFI

8

11

9

OSC SEL

* 4.4V FOR THE MAX693A/MAX800M

MAX800M

1.25V

TIMEBASE FOR

RESET AND

WATCHDOG

WATCHDOG
TRANSITION

DETECTOR

4

GND

CHIP-ENABLE

OUTPUT

CONTROL

RESET

GENERATOR

WATCHDOG

TIMER

6

2

12

16

15

14

10

LOW LINE

V

OUT

CE OUT

RESET

RESET

WDO

PFO

5.0V

4.0V

5.0V

0V

5V

0V

5V

0V

5V

0V

LOGIC LEVELS SHOWN ARE FROM 0V TO 5V.

V

RESET

THRESHOLD

CE IN

CE OUT

RESET

RESET

CC

15μs

100μs

100μs

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

______________________________________________________________________________________ 11

Power-Fail Output

The Power-Fail Output (PFO) goes low when PFI goes
below 1.25V. It typically sinks 3.2mA with a saturation
voltage of 0.1V. With PFI above 1.25V, PFO is actively
pulled to V

OUT

.

Battery-Backup Mode

Two conditions are required to switch to battery-back­up mode: 1) VCCmust be below the reset threshold,
and 2) VCCmust be below VBATT. Table 2 lists the sta­tus of the inputs and outputs in battery-backup mode.

Battery-On Output

The Battery-On (BATT ON) output indicates the status
of the internal VCC/battery-switchover comparator,
which controls the internal VCCand VBATT switches.
For VCCgreater than VBATT (ignoring the small hys­teresis effect), BATT ON typically sinks 3.2mA at 0.1V
saturation voltage. In battery-backup mode, this termi­nal sources approximately 10µA from V

OUT

. Use BATT
ON to indicate battery-switchover status or to supply
base drive to an external pass transistor for higher-cur­rent applications (see

Typical Operating Circuit

).

Input Supply Voltage

The Input Supply Voltage (VCC) should be a regulated
5V. V

CC

connects to V

OUT

via a parallel diode and a
large PMOS switch. The switch carries the entire cur­rent load for currents less than 250mA. The parallel
diode carries any current in excess of 250mA. Both the
switch and the diode have impedances less than 1Ω
each. The maximum continuous current is 250mA, but
power-on transients may reach a maximum of 1A.

Figure 6. CE Propagation Delay Test Circuit Figure 7. Low-Battery Indicator

PIN NAME STATUS

1 VBATT Supply current is 1µA max.

2 V

OUT

V

OUT

is connected to VBATT through an

internal PMOS switch.

3 V

CC

Battery switchover comparator monitors
V

CC

for active switchover.

4 GND GND 0V, 0V reference for all signals.

5 BATT ON

Logic high. The open-circuit output is
equal to V

OUT

.

6

LOWLINE

Logic low*

7 OSC IN OSC IN is ignored.

8 OSC SEL OSC SEL is ignored.

9 PFI

The power-fail comparator remains
active in the battery-backup mode for
V

CC

≥ VBATT - 1.2V typ.

10

PFO

The power-fail comparator remains
active in the battery-backup mode for
VCC≥ VBATT - 1.2V typ. Below this volt­age, PFO is forced low.

11 WDI Watchdog is ignored.

12

CE OUT

Logic high. The open-circuit voltage is
equal to V

OUT

.

13

CE IN

High impedance

14

WDO

Logic high. The open-circuit voltage is
equal to V

OUT

.

15

RESET

Logic low*

16 RESET High impedance*

Table 2. Input and Output Status in Battery-Backup
Mode

* V

CC

must be below the reset threshold to enter battery-backup

mode.

+5V

V

CC

VBATT

2.8V

50Ω

OUTPUT

IMPEDANCE

CE IN

MAX691A
MAX693A
MAX800L

MAX800M

GND

CE OUT

C

2.0V to 5.5V

LOAD

VBATT

PFI

MAX691A
MAX693A
MAX800L
MAX800M

+5V

V

CC

PFO

GND

LOW BATT

MAX691A/MAX693A/MAX800L/MAX800M

Battery-Backup Input

The Battery-Backup Input (VBATT) is similar to the V

CC

input except the PMOS switch and parallel diode are
much smaller. Accordingly, the on-resistances of the
diode and the switch are each approximately 10Ω.
Continuous current should be limited to 25mA and
peak currents (only during power-up) limited to 250mA.
The reverse leakage of this input is less than 1µA over
temperature and supply voltage (Figure 8).

Output Supply Voltage

The Output Supply Voltage (V

OUT

) pin is internally con­nected to the substrate of the IC and supplies current
to the external system and internal circuitry. All open­circuit outputs will, for example, assume the V

OUT

volt­age in their high states rather than the VCCvoltage. At
the maximum source current of 250mA, V

OUT

will typi-

cally be 200mV below V

CC

. Decouple this terminal with

a 0.1µF capacitor.

__________Applications Information

The MAX691A/MAX693A/MAX800L/MAX800M are not
short-circuit protected. Shorting V

OUT

to ground, other
than power-up transients such as charging a decou­pling capacitor, destroys the device.

All open-circuit outputs swing between V

OUT

and GND

rather than VCCand GND.

If long leads connect to the chip inputs, insure that
these leads are free from ringing and other conditions
that would forward bias the chip’s protection diodes.

There are three distinct modes of operation:

1) Normal operating mode with all circuitry powered
up. Typical supply current from V

CC

is 35µA while

only leakage currents flow from the battery.

2) Battery-backup mode where V

CC

is typically within

0.7V below VBATT. All circuitry is powered up
and the supply current from the battery is typically
less than 60µA.

3) Battery-backup mode where V

CC

is less than
VBATT by at least 0.7V. VBATT supply current is
1µA max.

Using SuperCap or MaxCap with the

MAX691A/MAX693A/MAX800L/MAX800M

VBATT has the same operating voltage range as VCC,
and the battery switchover threshold voltages are typi­cally ±30mV centered at VBATT, allowing use of a
SuperCap and a simple charging circuit as a backup
source (Figure 9).

If VCCis above the reset threshold and VBATT is 0.5V
above VCC, current flows to V

OUT

and VCCfrom VBATT
until the voltage at VBATT is less than 0.5V above VCC.
For example, with a SuperCap connected to VBATT and
through a diode to VCC, if VCCquickly changes from 5.4V
to 4.9V, the capacitor discharges through V

OUT

and V

CC

until VBATT reaches 5.1V typ. Leakage current through
the SuperCap charging diode and the internal power
diode eventually discharges the SuperCap to VCC. Also, if
VCCand VBATT start from 0.1V above the reset threshold
and power is lost at VCC, the SuperCap on VBATT dis­charges through VCCuntil VBATT reaches the reset
threshold; then the battery-backup mode is initiated and
the current through VCCgoes to zero.

Microprocessor Supervisory Circuits

12 ______________________________________________________________________________________

Figure 8. VCCand VBATT to V

OUT

Switch Figure 9. SuperCap or MaxCap on VBATT

+5V

V

VBATT

V

MAX691A
MAX693A
MAX800L

MAX800M

CC

0.1μF

V

OUT

1N4148

0.47F*

* MaxCap

1

VBATT

CC

MAX691A
MAX693A
MAX800L

MAX800M

GND

3

2

V

OUT

4

Using Separate Power Supplies

for VBATT and V

CC

If using separate power supplies for VCCand VBATT,
VBATT must be less than 0.3V above VCCwhen VCCis
above the reset threshold. As described in the previ­ous section, if VBATT exceeds this limit and power is
lost at VCC, current flows continuously from VBATT to
VCCvia the VBATT-to-V

OUT

diode and the V

OUT

-to-V

CC

switch until the circuit is broken (Figure 8).

Alternate Chip-Enable Gating

Using memory devices with both CE and CE inputs
allows the CE loop to be bypassed. To do this, con­nect CE IN to ground, pull up CE OUT to V

OUT

, and
connect –CE OUT to the CE input of each memory
device (Figure 10). The CE input of each part then
connects directly to the chip-select logic, which does
not have to be gated.

Adding Hysteresis to the

Power-Fail Comparator

Hysteresis adds a noise margin to the power-fail com­parator and prevents repeated triggering of PFO when
VINis near the power-fail comparator trip point. Figure
11 shows how to add hysteresis to the power-fail com-

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

______________________________________________________________________________________ 13

Figure 10. Alternate CE Gating

Figure 12. Monitoring a Negative Voltage

Figure 11. Adding Hysteresis to the Power-Fail Comparator

Rp*

V

OUT

CE IN

CE OUT

MAX691A
MAX693A
MAX800L

MAX800M

GND

*MAXIMUM Rp VALUE DEPENDS ON
THE NUMBER OF RAMS.
MINIMUM Rp VALUE IS 1kΩ.

ACTIVE-HIGH

CE LINES

FROM LOGIC

V

IN

CE

RAM 1

CE

CE

RAM 2

CE

CE

RAM 3

CE

CE

RAM 4

CE

R1

C1*

R2

5V

PFO

0V

0V V

= 1.25

V

TRIP

R2

= 1.25/

V

H

R1 + R2 I I R3 R1 R3 R2

R3

TO μP

R1 + R2

R2 I I R3 VL - 1.25 + 5 - 1.25 = 1.25

PFI

PFO

+5V

V

CC

MAX691A
MAX693A
MAX800L

MAX800M

GND

V

V

TRIP

L

V

IN

*OPTIONAL

H

+5V

R1

PFI

MAX691A
MAX693A

R2

MAX800L

MAX800M

5V

PFO

0V

5 - 1.25 = 1.25 - V
R1 R2

NOTE: V

TRIP

V-

TRIP

IS NEGATIVE.

V

TRIP

V-

V

GND

CC

PFO

0V

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

14 ______________________________________________________________________________________

parator. Select the ratio of R1 and R2 such that PFI sees

1.25V when VINfalls to the desired trip point (V

TRIP

).
Resistor R3 adds hysteresis. It will typically be an order
of magnitude greater than R1 or R2. The current
through R1 and R2 should be at least 1µA to ensure that
the 25nA (max) PFI input current does not shift the trip
point. R3 should be larger than 10kΩ to prevent it from
loading down the PFO pin. Capacitor C1 adds noise
rejection.

Monitoring a Negative Voltage

The power-fail comparator can be used to monitor a
negative supply voltage using Figure 12’s circuit. When
the negative supply is valid, PFO is low. When the neg­ative supply voltage drops, PFO goes high. This cir­cuit’s accuracy is affected by the PFI threshold
tolerance, the VCCvoltage, and resistors R1 and R2.

Backup-Battery Replacement

The backup battery may be disconnected while VCCis
above the reset threshold. No precautions are neces­sary to avoid spurious reset pulses.

Negative-Going VCCTransients

While issuing resets to the µP during power-up, power­down, and brownout conditions, these supervisors are
relatively immune to short-duration, negative-going V

CC

transients (glitches). It is usually undesirable to reset
the µP when VCCexperiences only small glitches.

Figure 13 shows maximum transient duration vs. reset­comparator overdrive, for which reset pulses are not
generated. The graph was produced using negative­going VCCpulses, starting at 5V and ending below the
reset threshold by the magnitude indicated (reset com­parator overdrive). The graph shows the maximum
pulse width a negative-going VCCtransient may typical­ly have without causing a reset pulse to be issued. As
the amplitude of the transient increases (i.e., goes far­ther below the reset threshold), the maximum allowable
pulse width decreases. Typically, a VCCtransient that
goes 100mV below the reset threshold and lasts for
40µs or less will not cause a reset pulse to be issued.

A 100nF bypass capacitor mounted close to the V

CC

pin provides additional transient immunity.

Connecting a Timing Capacitor at OSC IN

When OSC SEL is connected to ground, OSC IN dis­connects from its internal 10µA (typ) pullup and is inter­nally connected to a ±100nA current source. When a
capacitor is connected from OSC IN to ground (to
select alternative reset and watchdog timeout periods),
the current source charges and discharges the timing
capacitor to create the oscillator that controls the reset
and watchdog timeout period. To prevent timing errors
or oscillator startup problems, minimize external current
leakage sources at this pin, and locate the capacitor as
close to OSC IN as possible. The sum of PC-board
leakage plus OSC capacitor leakage must be small
compared to ±100nA.

Figure 13. Maximum Transient Duration without Causing a
Reset Pulse vs. Reset Comparator Overdrive

100

VCC = 5V

= +25°C

T

A

80

0.1μF CAPACITOR
FROM V

OUT

TO GND

MAX791-16

60

40

20

MAXIMUM TRANSIENT DURATION (μs)

0

10 1000 10000

100

RESET COMPARATOR OVERDRIVE,

(Reset Threshold Voltage - V

CC

) (mV)

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

______________________________________________________________________________________ 15

Maximum VCCFall Time

The VCCfall time is limited by the propagation delay of
the battery switchover comparator and should not
exceed 0.03V/µs. A standard rule of thumb for filter
capacitance on most regulators is on the order of 100µF
per amp of current. When the power supply is shut off or
the main battery is disconnected, the associated initial
VCCfall rate is just the inverse or 1A/100µF = 0.01V/µs.
The VCCfall rate decreases with time as VCCfalls expo­nentially, which more than satisfies the maximum fall-time
requirement.

Watchdog Software Considerations

A way to help the watchdog timer keep a closer watch
on software execution involves setting and resetting the
watchdog input at different points in the program,
rather than “pulsing” the watchdog input high-low-high
or low-high-low. This technique avoids a “stuck” loop
where the watchdog timer continues to be reset within
the loop, keeping the watchdog from timing out. Figure
14 shows an example flow diagram where the I/O dri­ving the watchdog input is set high at the beginning of
the program, set low at the beginning of every subrou­tine or loop, then set high again when the program
returns to the beginning. If the program should “hang”
in any subroutine, the I/O is continually set low and the
watchdog timer is allowed to time out, causing a reset
or interrupt to be issued.

Figure 14. Watchdog Flow Diagram

START

SET

WDI

LOW

SUBROUTINE

OR PROGRAM LOOP

SET WDI

HIGH

RETURN

END

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

16 ______________________________________________________________________________________

Ordering Information (continued)

*

Dice are specified at TA= +25°C, DC parameters only.

**

Contact factory for availability and processing to MIL-STD-883B.

Devices in PDIP, SO and TSSOP packages are available in both
leaded and lead-free packaging. Specify lead free by adding
the + symbol at the end of the part number when ordering.
Lead free not available for CERDIP package.

___________________Chip Topography

SUBSTRATE CONNECTED TO V

OUT

Package Information

For the latest package outline information and land patterns, go
to www.maxim-ic.com/packages

.

PACKAGE TYPE PACKAGE CODE DOCUMENT NO.

16 TSSOP U16-1

21-0066

16 CERDIP J16-3

21-0045

16 Narrow SO S16-3

21-0041

16 Plastic DIP P16-1

21-0043

16 Wide SO W16-1

21-0042

PART TEMP RANGE

MAX691AEJE -40°C to +85°C 16 CERDIP

MAX691AMJE -55°C to +125°C 16 CERDIP**

MAX691AMSE/PR -55°C to +125°C 16 Wide SO**

MAX691AMSE/PR-T -55°C to +125°C 16 Wide SO**

MAX693ACUE -0°C to +70°C 16 TSSOP

MAX693ACSE -0°C to +70°C 16 Narrow SO

MAX693ACWE -0°C to +70°C 16 Wide SO

MAX693ACPE -0°C to +70°C 16 Plastic DIP

MAX693AC/D -0°C to +70°C Dice*

MAX693AEUE -40°C to +85°C 16 TSSOP

MAX693AESE -40°C to +85°C 16 Narrow SO

MAX693AEWE -40°C to +85°C 16 Wide SO

MAX693AEPE -40°C to +85°C 16 Plastic DIP

MAX693AEJE -40°C to +85°C 16 CERDIP

MAX693AMJE -55°C to +125°C 16 CERDIP

MAX800LCUE -0°C to +70°C 16 TSSOP

MAX800LCSE -0°C to +70°C 16 Narrow SO

MAX800LCPE -0°C to +70°C 16 Plastic DIP

MAX800LEUE -40°C to +85°C 16 TSSOP

MAX800LESE -40°C to +85°C 16 Narrow SO

MAX800LEPE -40°C to +85°C 16 Plastic DIP

MAX800MCUE -0°C to +70°C 16 TSSOP

MAX800MCSE -0°C to +70°C 16 Narrow SO

MAX800MCPE -0°C to +70°C 16 Plastic DIP

MAX800MEUE -40°C to +85°C 16 TSSOP

MAX800MESE -40°C to +85°C 16 Narrow SO

MAX800MEPE -40°C to +85°C 16 Plastic DIP

PIN ­PA C K A G E

V

CC

GND

BATT ON

LOW LINE

V

OSC IN

OUT

OSC SEL

VBATT RESET RESET

PFI PFO

0.07"

(1.778mm)

WDO

CE IN

CE OUT

WDI

0.11"

(2.794mm)

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________

17

© 2008 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.

MAX691A/MAX693A/MAX800L/MAX800M

Microprocessor Supervisory Circuits

Revision History

REVISION

NUMBER

0 09/92 Initial release —

1 12/92 Update Electrical Characteristics table. 2, 3, 4

2 5/93 Update Electrical Characteristics table, Tables 1 and 2. 2, 3, 4, 9, 11

3 12/93 Update Electrical Characteristics table. 2, 3, 4

4 3/94 Update Electrical Characteristics table. 2, 3, 4

5 8/94 Correction to Figure 4. 10

6 1/95 Update to new revision and correct errors. —

7 12/96 Update Electrical Characteristics table. 2, 3, 4

8 12/99

9 4/02 Corrected Ordering Information.1

10 11/05 Added lead-free information. 1, 16

11 8/08 Updated Ordering Information. 1, 16

REVISION

DATE

DESCRIPTION

Updated Ordering Information, Pin Configuration, Absolute Maximum
Ratings, and Package Information.

PAGES

CHANGED

1, 2, 16