FreeWave ZumLink Z9-C, ZumLink Z9-T, LUM0075AA User Manual

ZumLink Z9-C or Z9-T

Covers Model: Z9-C or Z9-T

User Manual

Part Number: LUM0075AA

Revision: May-2016

Safety Information

The products described in this manual could fail in a variety of modes due to misuse, age, or malfunction.
Systems with these products must be designed to prevent personal injury and property damage during product
operation and in the event of product failure.

Warning! Remove power before connecting or disconnecting the interface or RF cables.

Warranty Information

FreeWave Technologies, Inc. warrants the FreeWave® ZumLink Z9-C or Z9-T (Product) against defects in
materials and manufacturing for a period of two years from the date of shipment, depending on model number. In
the event of a Product failure due to materials or workmanship, FreeWave will, at its discretion, repair or replace
the Product. For evaluation of Warranty coverage, return the Product to FreeWave upon receiving a Return
Material Authorization(RMA).

In no event will FreeWave Technologies, Inc., its suppliers, or its licensors be liable for any damages arising from
the use of or inability to use this Product. This includes business interruption, loss of business information, or
other loss which may arise from the use of this Product. OEM customer’s warranty periods can vary.

Warranty Policy will not apply in the following circumstances:

1. If Product repair, adjustments, or parts replacements are required due to accident, neglect, or undue
physical, electrical, or electromagnetic stress.

2. If Product is used outside of FreeWave specifications as stated in the Product's data sheet.

3. If Product has been modified, repaired, or altered by Customer unless FreeWave specifically authorized
such alterations in each instance in writing. This includes the addition of conformal coating.

Special Rate Replacement Option

A special rate replacement option is offered to non-warranty returns or upgrades. The option to purchase the
replacement unit at this special rate is only valid for that RMA. The special replacement rate option expires if not
exercised within 30 days of final disposition of the RMA.

Copyright © 2016 by FreeWave Technologies, Inc.
All rights reserved.

Page 2 of 40 LUM0075AA Rev May-2016

This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by

FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from

FreeWave Technologies, Inc.

5395 Pearl Parkway, Suite 100

Boulder, CO 80301

303.381.9200

Toll Free: 1.866.923.6168

Fax: [phone]

www.freewave.com

FreeWave Technologies, Inc.

Export Notification

FreeWave Technologies, Inc. products may be subject to control by the Export Administration Regulations
(EAR) and/or the International Traffic in Arms Regulations (ITAR). Export, re-export, or transfer of these
products without required authorization from the U.S. Department of Commerce, Bureau of Industry and
Security, or the U.S. Department of State, Directorate of Defense Trade Controls, as applicable, is
prohibited. Any party exporting, re-exporting, or transferring FreeWave products is responsible for
obtaining all necessary U.S. government authorizations required to ensure compliance with these and other
applicable U.S. laws. Consult with your legal counsel for further guidance.

FCC Notifications

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This
device may not cause harmful interference and 2) this device must accept any interference received, including
interference that may cause undesired operation.

The content of this guide covers FreeWave Technologies, Inc. models sold under FCC ID: KNYPMT0101AB.

All models sold under the listed FCC ID(s) must be installed professionally and are only approved for use when
installed in devices produced by FreeWave Technologies or third party OEMs with the express written approval
of FreeWave Technologies, Inc. Changes or modifications should not be made to the device.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.

FCC NEMA Installation and Label

Where applicable, the models described in this guide must be installed in a NEMA enclosure. When any
FreeWave Technologies, Inc. module is placed inside an enclosure, a label must be placed on the outside of the
enclosure. The label must include the text: "Contains Transmitter Module with FCC ID: KNYPMT0101AB."

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 52 cm between the radiator and your body.

FCC Notification of Power Warning

The ZumLink Z9-C or Z9-T covered in this document has a maximum transmitted output power of +30dBm.

The antennas used MUST provide a separation distance of at least 52 cm from all persons and MUST NOT be
co-located or operate in conjunction with any other antenna or transmitter.

IC Notifications

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.

Ce dispositif est conforme aux normes permis-exemptes du Canada RSS d'industrie. L'opération est sujette aux
deux conditions suivantes : (1) ce dispositif peut ne pas causer l'interférence, et (2) ce dispositif doit accepter
n'importe quelle interférence, y compris l'interférence qui peut causer le fonctionnement peu désiré du dispositif.

GNU License Notification

Some of the software in the firmware is licensed under the GNU General Public License and other Open Source
and Free Software licenses. Contact FreeWave to obtain the corresponding source on CD.

Restricted Rights

Any product names mentioned in this manual may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged.

This manual is only for use by purchasers and other authorized users of FreeWave products.

Page 3 of 40 LUM0075AA Rev May-2016

This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by

FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from

FreeWave Technologies, Inc.

No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical,
or for any purpose without the express written permission of FreeWave Technologies, Inc. FreeWave reserves
the right to make changes to this manual without notice. FreeWave assumes no responsibility or liability for the
use of this manual or the infringement of any copyright or other proprietary right.

UL Power Source

Input power shall be derived from a certified, Class 2:

l single power source or

l an limited power source (LPS) in accordance with IEC/EN 60950-1.

l Input voltage for the ZumLink Z9-C or Z9-T is +3 to +5VDC (±10%).

ZumLink Z9-C or Z9-T Product Safety

Standards and Editions

l HazLoc Standards

l ANSI/ISA 12.12.01-2013

l Ordinary Location Standards

l UL 60950, 2nd Edition

l CAN/CSA-C22.2 No. 60950, 2nd Edition

l IEC 60950, 2nd Edition

l EN 60950, 2nd Edition

Schedule of Limitations

l Antenna connection is internal wiring only.

l The Ex Components shall only be used in an area of not more than pollution degree 2, as defined in

IEC/EN60664-1.

l The Ex Components shall be installed in an enclosure with tool removable door or cover that provides a

degree of protection not less than IP 54 in accordance with IEC/EN60679-15.

l Transient protection shall be provided that is set at a level not exceeding 140 % of the peak rated voltage

value at the supply terminals to the equipment.

l All connectors (J1 to J4) do not have mating connectors with the devices.

l The securement of these connectors must be evaluated during end-product investigation.

l Temperature test was conducted at a rated supply voltage and the maximum surface temperature of 61°C

was recorded at 60°C ambient temperature.

Page 4 of 40 LUM0075AA Rev May-2016

This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by

FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from

FreeWave Technologies, Inc.

ZumLink Z9-C or Z9-T: User Manual

Table of Contents

Preface 6

1. ZumLink Z9-C or Z9-T Included Equipment 8

2. ZumLink Z9-C or Z9-T CLI Configuration 9

3. Approved Antennas 14

3.1 900MHz Antennas 14

3.1.1 900MHz Omni-Directional Antennas 14

3.1.2 900MHz Directional Antennas 15

3.1.3 Alternative Antennas 15

4. ZumLink Z9-C or Z9-T Data Interface Connector 16

5. ZumLink Z9-C or Z9-T Settings and Descriptions 18

config 19

diagPortConfig 20

radioSettings 22

radioStatus 33

serialPortConfig 34

system 35

systemInfo 36

Appendix A: ZumLink Z9-C or Z9-T 900MHz Technical Specifications 37

LUM0075AA Rev May-2016 Page 5 of 40

This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by

FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from

FreeWave Technologies, Inc.

ZumLink Z9-C or Z9-T: User Manual

Preface

Contacting FreeWave Technical Support

For up-to-date troubleshooting information, check the Support page at www.freewave.com.

FreeWave provides technical support Monday through Friday, 8:00 AM to 5:00 PM Mountain
Time (GMT -7).

l Call toll-free at 1.866.923.6168.

l In Colorado, call 303.381.9200.

l Contact us through e-mail at [e-mail].

Printing this Document

This document is set to print double-sided with a front cover and a back cover. Viewing this
document online with a PDF viewer, may show pages intentionally left blank to accommodate the
double-sided printing.

Document Styles

This document uses these styles:

l FreeWave applications appear as: FreeWave.

l Parameter setting text appears as: [Page=radioSettings]

l File names appear as: configuration.cfg.

l File paths appear as: C:\Program Files (x86)\FreeWave Technologies.

l User-entered text appears as: xxxxxxxxx.

rd

l 3

-party names appear as: Notepad®.

LUM0075AA Rev May-2016 Page 6 of 40

This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by

FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from

FreeWave Technologies, Inc.

Preface

Caution: Indicates a situation that MAY cause damage to personnel, the radio, data, or
network.

Example: Provides example information of the related text.

FreeWave Recommends: Identifies FreeWave recommendation information.

Important!: Provides crucial information relevant to the text or procedure.

Note: Emphasis of specific information relevant to the text or procedure.

Provides time saving or informative suggestions about using the product.

Warning! Indicates a situation that WILL cause damage to personnel, the radio, data, or
network.

Documentation Feedback

Send comments or questions about this document's content to [e-mail]. In the
email, include the title of the document or the document's part number and revision letter (found in
the footer).

Page 7 of 40 LUM0075AA Rev May-2016

This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by

FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from

FreeWave Technologies, Inc.

ZumLink Z9-C or Z9-T: User Manual

1. ZumLink Z9-C or Z9-T Included Equipment

The ZumLink Z9-C or Z9-T package contains these items:

ZumLink Z9-C or Z9-T Included Equipment

Qty Description

1 ZumLink Z9-C or Z9-T device

Note: See Approved Antennas (on page 14) for detailed information.
Approved antennas can be purchased directly from FreeWave.

LUM0075AA Rev May-2016 Page 8 of 40

This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by

FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from

FreeWave Technologies, Inc.

ZumLink Z9-C or Z9-T: User Manual

2. ZumLink Z9-C or Z9-T CLI Configuration

Important!: A Serial Port on the computer is required for this procedure.

1. Using the Data Interface Connector (see ZumLink Z9-C or Z9-T Data Interface

Connector (on page 16) for location):

a. Apply power to the ZumLink.

b. Connect to the Serial Interface of the ZumLink.

l The Z9-C model has an RS232 interface and can be connected directly to an

RS232 device.

l FreeWave offers a cable (ASC2414DJ) from the radio to a DB9 connector that

includes a reset button and power input jack.

l The Z9-T model has a TTL interface and does NOT work directly with RS232.

l If connecting up to a device or circuit that is RS232, a circuit is required to adapt

between the two interfaces.

2. If the ZumLink is connected to a computer, open a terminal program (e.g., Tera Term).

Note: In this example procedure, Tera Term is used.

3. In Tera Term, on the File menu, select New Connection.

LUM0075AA Rev May-2016 Page 9 of 40

This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by

FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from

FreeWave Technologies, Inc.

2. ZumLink Z9-C or Z9-T CLI Configuration

Figure 1: File menu > New Connection

The Tera Term New Connection dialog box opens.

4. Click the Port list box arrow and select the COM port the ZumLink device is connected to.

5. Click OK to save the changes and close the dialog box.
The Tera Term window shows the connected COM port and Baud rate in the title bar of the
window.

6. In the Tera Term window, click the Setup menu and select Serial Port.

Page 10 of 40 LUM0075AA Rev May-2016

This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by

FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from

Figure 2: Select the ZumLink COM port

FreeWave Technologies, Inc.

Figure 3: Serial menu > Setup Port

The Tera Term: Serial Port Setup dialog box opens.

Note: The image shows the default ZumLink settings.

ZumLink Z9-C or Z9-T: User Manual

Figure 4: Tera Term: Serial Port Setup dialog box with default settings

7. Verify, and change if required, the Tera Term serial port settings (except the Port setting)
of the connected ZumLink so the settings are the same as the defaults shown in the image.

Example: If the Baud Rate is 9600, click the list box arrow and select 115200.

8. Click OK to save the changes and close the dialog box.

9. On the ZumLink, pull the Pin 2-Interrupt line Low to activate the FreeWave Shell and
disrupt data flow.

10. Return Pin 2-Interrupt to High.

LUM0075AA Rev May-2016 Page 11 of 40

This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by

FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from

FreeWave Technologies, Inc.

2. ZumLink Z9-C or Z9-T CLI Configuration

11. In Tera Term, press <Enter>.
The FreeWave Shell returns.

Figure 5: FreeWave Shell in Tera Term

12. At the > prompt, type pages and press <Enter>.
The available ZumLink information appears.

13. Type radiosettings and press <Enter>.
The ZumLink radioSettings appear.

Page 12 of 40 LUM0075AA Rev May-2016

This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by

FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from

Figure 6: Pages information

FreeWave Technologies, Inc.