Freescale Semiconductor TWR-S08UNIV Quick Start Guide

Quick Start Guide
Universal RS08/S08 MCU module
(TWR-S08UNIV)
TOWER SYSTEM Quick Start Guide for TWR-S08UNIV
TOWER SYSTEM
Get to Know the TWR-S08UNIV
Primary Connector
S08/RS08 Daughter Card Socket
Daughter Card MCU Power
MCU Power LED
Power /OSBDM Mini-B USB Connector
Secondary Connector
Touch Pad
TWRPI Socket
General
TWRPI Socket
Touch Sense
TWRPI
Beeper (bottom)
RGB LED
SW4
SW3
Potentiometer
User Interface
Jumpers
TWR-S08UNIV Freescale Tower System
The TWR-S08UNIV universal RS08/S08 board is part of the Freescale Tower System, a modular development platform that enables rapid prototyping and tool re-use through reconfigurable hardware. Take your design to the next level and begin constructing your Tower System today by visiting freescale.com/Tower for additional Tower System microcontroller modules and compatible peripherals.
Get to Know the TWR-S08DC
TOWER SYSTEM Quick Start Guide for TWR-S08UNIV
MC9S08AC60 3V/5V Switch
TWR-S08DC-AC60
MC9S08QG8
TWR-S08DC-QG8
MC9S08QE64
TWR-S08DC-QE64
MC9S08SH8
TWR-S08DC-SH8
MC9RS08KA8
TWR-RS08DC-KA8
MC9S08QD4
TWR-S08DC-QD4
TOWER SYSTEM
Step-by-Step Installation Instructions
In this Quick Start Guide, you will learn how to set up the TWR-S08UNIV and TWR-S08DC modules and run the default demonstration.
STEP
Install the Software
1
and Tools
Install the P&E Micro Tower Toolkit to install the OSBDM and USB-to-Serial drivers. These can be found on the DVD under “Software.”
STEP
Configure Hardware
2
a) Select one of the TWR-(R)S08DC daughter cards. Plug it into the TWR-S08UNIV board. Ensure that the white arrows are aligned.
TOWER SYSTEM Quick Start Guide for TWR-S08UNIV
b) Connect one end of the USB cable to the PC and the other end to the power/OSBDM mini-B connector on the TWR-S08UNIV module. Allow the PC to automatically configure the USB drivers if needed. Turn on the SW2 MCU power switch.
STEP
Play
3
Turn the dial on the potentiometer (R25) and the LED (D6) will flash faster or slower depending on the position of the dial.
TOWER SYSTEM
STEP
Explore Further
4
CodeCreator software found on the DVD under “Software.” The CodeCreator software is a quick and easy-to-use GUI that allows you to create an RS08/ S08 peripheral module example and complete a CodeWarrior project in under 10 seconds.
Install CodeWarrior IDE and
STEP
Learn More
5
Explore advanced options for several of the daughter cards. Daughter cards will support connections using the on-board OSBDM serial port. Easy access to peripherals signals such as I2C, SPI and UART is provided through the breakout headers and the Tower System primary connector. The Tower System plug-in sockets interface to off-the-shelf sensor boards, including capacitive touch, inertial and pressure. Learn more about the TWR-S08UNIV board and the TWR-S08DC daughter cards at freescale.com/TWR-S08UNIV.
TOWER SYSTEM Quick Start Guide for TWR-S08UNIV
TOWER SYSTEM
TOWER SYSTEM
To learn more about the TWR-S08UNIV and the TWR-S08DC daughter cards, visit freescale.com/TWR-S08UNIV. To become a member of the online Tower Geeks community, visit towergeeks.org.
Freescale, the Freescale logo and CodeWarrior are trad emarks or registered tradem arks of Freescale Semiconductor, Inc. Reg. U.S. Pat. & Tm. Off. All other product or service name s are the property of their respec tive owners. © 2 011 Freescale Semiconduc tor, Inc.
Doc Number: T WRUNIVQSG / REV 0 Agile Number: 926-78608 / REV A
Loading...