Quick Start Guide
TWR-K70F120M
High-Performance MCUs with Graphics
LCD, Connectivity and Security
TOWER SYSTEM
Quick Start Guide
Get to Know the TWR-K70F120M
Primary
Connector
Infra-Red
General Purpose
Tower Plug-In
(TWRPI) Socket
SW3 (Reset)
Power/OSJTAG
Mini-B USB
Connector
Secondary
Connector
2
Figure 1: Front side of TWR-K70F120M module (TWRPI devices not shown).
SW1
SW2
Touch TWRPI
Socket
LED/Touch
Buttons
E1–E4
MK70FN1M0VMJ12
Microcontroller
MMA8451
Accelerometer
1 Gb 16-bit wide
LPDDR2 Memory
Potentiometer
TOWER SYSTEM
SD Card
Socket
VBAT (RTC)
Battery
Holder
MC9S08JM60
OSJTAG Circuit
2 Gb NAND
Flash
Figure 2: Back side of TWR-K70F120M module.
TWR-K70F120M
Freescale Tower System
The TWR-K70F120M module is part of the Freescale Tower System, a modular
development platform that enables rapid prototyping and tool re-use through
reconfigurable hardware. The TWR-K70F120M can be used with a broad
selection of Tower System peripheral modules, including the new TWR-LCD-RGB
which accepts RGB data from the K70 MCU graphics LCD controller.
3
Quick Start Guide
TWR-K70F120M Features
• MK70FN1M0VMJ12 MCU (120 MHz, 1 MB flash, graphics
LCD, Ethernet, USB OTG, tamper detection, encryption, NAND
flash and DDR controller, 256 MBGA)
• Interfaces to the new TWR-LCD-RGB Tower peripheral module
(accepts RGB data directly from the K70 MCU LCD controller)
• MC9S08JM60 open source JTAG (OSJTAG) circuit
• Micron MT47H64M16HR-25 1 Gb 16-bit wide LPDDR2 memory
• Micron MT29F2G16ABAEAWP 2 Gb NAND flash
• Four user-controlled status LEDs
• Four capacitive touch pads and two mechanical push buttons
• General-purpose TWRPI socket (Tower plug-in module)
• TWRPI-TOUCH-STR socket (touch-sensing Tower
plug-in module)
4
TOWER SYSTEM
Step-by-Step Installation Instructions
Install the
1
Software and Tools
Install the P&E Micro Kinetis Tower
toolkit. The toolkit includes the
OSJTAG and USB to serial drivers.
These can be found on the DVD
under Software.
Configure the
2
Hardware
Install the included battery into the
VBAT (RTC) battery holder. Then,
connect one end of the USB cable
to the PC and the other end to the
Power/OSJTAG mini-B connector
on the TWR-K70F120M module.
Allow the PC to automatically
configure the USB drivers if needed.
Tilt the
3
Board
Tilt the board side to side to see
the LEDs on E1–E4 light up as it is
tilted. While the board is held flat,
touch the pads on E1–E4 to
toggle the LEDs.
Play the
4
Memory Game
Press SW2 to play a memory recall
game using the touch pads E1–E4.
A sequence will light up, then press
the touch pads in the order flashed.
If an incorrect sequence is touched
or too much time has elapsed, all
the lights will blink rapidly and the
game will reset.
Press SW1 to return to the
accelerometer demo.
5
Quick Start Guide
Download the TWR-
5
K70F120M User Manual
and Demonstration Labs
Download the TWR-K70120M user
manual and demonstration labs at
freescale.com/TWR-K70F120M.
Download the Freescale
6
CodeWarrior IDE and
MQX™ RTOS
Download the Freescale
CodeWarrior IDE and MQX RTOS by
clicking on the relevant links on the
Software tab of the Tower Kit DVD.
TWR-K70F120M Jumper Options
The following is a list of all jumper options. The default installed jumper settings are
shown in white text within the red boxes.
Jumper Option Setting Description
J8 MCU Power Connection ON Connect on-board 3.3-volt supply to MCU
OFF Isolate MCU from power
J20 MCU VDD_INT Power
Connection
J17 VBAT Power Selection 1-2 Connect VBAT to on-board 3.3-volt supply
6
ON Connect VDD and VDD_INT rails together
OFF Isolate MCU VDD_INT from power
2-3 Connect VBAT to the higher voltage between
(connect an ammeter to measure current)
(connect an ammeter to measure current)
on-board 3.3-volt supply or coin-cell supply
TOWER SYSTEM
TWR-K70F120M Jumper Options (continued)
Jumper Option Setting Description
J18 Clock Input Source
Selection
J10 OSJTAG Bootloader
Selection
J19 50 MHz clock disable ON ON = on-board 50 MHz oscillator enabled
J12 JTAG Board Power
Connection
J2 IR Transmitter
Connection
J16 IR Receiver Connection ON Connect DAC1_OUT/CMP2_IN3 to IR receiver
J1 VREGIN Power
Connection
1-2 Connect main EXTAL to on-board 50 MHz clock
2-3 Connect EXTAL to the CLKIN0 signal on the elevator
connector
ON OSJTAG bootloader mode
(OSJTAG firmware reprogramming)
OFF Debugger mode
OFF OFF = on-board 50 MHz oscillator disabled
ON Connect on-board 5-volt supply to JTAG port
(supports powering board from JTAG pod
supporting 5-volt supply output)
OFF Disconnect on-board 5-volt supply to JTAG port
ON Connect PTD7/CMT_IRO to IR transmitter (D1)
OFF Disconnect PTD7/CMT_IRO from IR transmitter (D1)
OFF Disconnect DAC1_OUT/CMP2_IN3 from IR receiver
ON Connect USB0_VBUS from elevator to VREGIN
OFF Disconnect USB0_VBUS from elevator to VREGIN
7
Quick Start GuideQuick Start Guide
Visit freescale.com/TWR-K70F120M,
freescale.com/K70 or freescale.com/Kinetis
for information on the TWR-K70F120M module,
including:
• TWR-K70F120M user guide
• TWR-K70F120M schematics
• Tower System fact sheet
For more information, visit freescale.com/Tower
Join the online Tower community at towergeeks.org
Freescale, the Freescale logo and CodeWarrior are trademarks of
Freescale semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product
or service names are the property of their respective owners.
© 2011 Freescale Semiconductor, Inc.
Doc Number: TWRK70F120MQSG REV 0
Agile Number: 926-78651 REV A
Loading...