SWIRL
1
54
"
4
INSTALLATION GUIDE
7
FREENOTES HARMONY PARK
194 BODO DRIVE, UNIT F
DURANGO CO 81303
TEL: (970) 375-7825
FAX: (970) 247-0856
WWW.FREENOTESHARMONYPARK.COM
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
FREENOTES HARMONY PARK. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF FREENOTES HARMONY
PARK IS PROHIBITED.
5
"
8
80" Adult
71" Ages 7-11
63" Ages 5-7
59" Ages 3-5
Main Features:
(LH) C Major / (RH) A Minor Pentatonic
•
Recycled HDPE Frame
•
Anodized Aluminum Chimes & Resonators
•
Stainless Steel Hardware
•
Contents:
SHEET 2 - Parts List and Instrument to Post Installation
•
SHEET 3 - In Ground Installation
•
SHEET 4 - Surface Mount Installation
•
Weights:
Instrument Weight, 197lbs.
•
Boxed Instrument Weight, 215lbs.
•
Boxed Posts Weight, 65-87lbs.
•
Swirl - Installation Guide
TITLE:
REVISION: B
SCALE: 1:16
DATE: 2/9/2018
SHEET 1 OF 4
SWRL-INSTALL
DWG. NO.
Parts List:
ITEM NO.
1
2
3
4
5
6
7
8
9
10
11
PART DESCRIPTION
Swirl Instrument Assembly
Large SS Holster
In Ground Recycled Post, 96"lg.
In Ground Steel Post, 96"lg.
Surface Mount Steel Post, 60"lg.
#8 Flat Head Screw, .5"lg. SS, T15 tamp
#8 Button Head Screw, 1.25"lg. SS, T15 tamp
#10-24 Button Head Machine Screw, 1"lg. SS, T25 tamp
3/8"-16 Wedge Expansion Anchor, 3.75"lg. SS
35/64" Hex Nut Cap
Security Driver
In Ground -
Recycled Post/QTY.
1 1 1
2 2 2
2
-
- 12 12 12
12
-
- -
- -
1 1 1
In Ground -
Steel Post/QTY.
- -
2
- -
12 12
Surface Mount -
Steel Post/QTY.
-
2
8
8
FREENOTES HARMONY PARK
194 BODO DRIVE, UNIT F
DURANGO CO 81303
TEL: (970) 375-7825
FAX: (970) 247-0856
WWW.FREENOTESHARMONYPARK.COM
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
FREENOTES HARMONY PARK. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF FREENOTES HARMONY
PARK IS PROHIBITED.
Step 1:
Start by mounting the Holsters to the Instrument Back with the provided #8 Flat Head Screws and Driver. The Back comes
predrilled. Screw heads should be flush with the Holster surface when properly installed. Holster should also be flush along the
back. Drive Screws slowly to prevent stripping.
Step 2:
With two people, situate the Instrument with Holsters installed onto the Posts. Posts come predrilled and/or tapped. Fasten the
Instrument to the Posts with the provided #8 Button Head Screw for Recycled Posts or #10-24 Button Head Machine Screw for
Steel Posts. Drivers are provided.
1
DETAIL A
8
SCALE 1 : 4
9/10
2
SWRL-INSTALL
DETAIL B
SCALE 1 : 4
Parts List and Instrument to Post Installation
TITLE:
REVISION: B
SCALE: 1:16
DATE: 2/9/2018
SHEET 2 OF 4
DWG. NO.
Step 1:
Excavate two 10" diameter holes, 36" deep, and 32" on center at the installation location. Contractor can modify Post to
desired height.
Post Length = Frost Depth
(36" Recommended)
+ Finished Post Height
Finished Post Height Guideline: (
Step 2:
Step 3:
With two people, lower the Posts with the Instrument attached into the excavated holes.
Verify the correct placement, levelness, and finished height of the Instrument. Check for sufficient clearance around the
Ages 3-5, 39"
) (
Ages 5-7, 43"
) (
Ages 7-11, 51"
) (
Adult, 60"
)
Instrument, a 36" perimeter around the Instrument is recommended for wheelchair accessibility.
Step 4:
Last pour concrete around the posts. It is recommended to brace the Instrument to hold it rigid while the concrete cures.
Leave to set according to the concrete manufacturers guidelines. Approximately (6) 80lb. bags will be needed.
1
FREENOTES HARMONY PARK
194 BODO DRIVE, UNIT F
DURANGO CO 81303
TEL: (970) 375-7825
FAX: (970) 247-0856
WWW.FREENOTESHARMONYPARK.COM
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
FREENOTES HARMONY PARK. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF FREENOTES HARMONY
PARK IS PROHIBITED.
3/4
Ground Level
32" On
Center
Post Length
Finished Post Height
Frost Depth
In Ground Installation
TITLE:
REVISION: B
SCALE: 1:16
DATE: 2/9/2018
SHEET 3 OF 4
SWRL-INSTALL
DWG. NO.
Step 1:
Standard height for Surface Mount Posts are 60".
The height of Surface Mount Steel Posts can not be adjusted.
Step 2:
Determine installation location. Verify concrete footing is a minimum of 48" long x 30" wide x 6" thick. If the concrete pad is at
an angle, steel washers are required to act as shims (Shims not provided). If there is not already an existing pad, approximately
(9) 80lb. bags will be needed. Allow concrete to cure per concrete manufacturers guidelines.
Step 3:
With two people place the Instrument Assembly with Posts attached onto the concrete pad and mark the center of the holes
on the surface mount bases. After you have made your marks, set aside the Instrument in order to drill for anchor holes. With a
hammer or rotary drill, drill through concrete at marked locations. Drill to a minimum depth of 4". A 3/8" masonry drill bit will be
needed.
Step 4:
Place the Instrument back over the drilled out holes. Insert provided anchor bolts into aligned holes. Position anchor nut so that
it is flush with the top of the bolt. Pound anchor bolts into the hole until the anchor washer is flush with the surface mount bases.
Tighten anchor bolts until they are snug. Cover remaining bolt sections with provided nut caps.
Step 5:
Verify the correct placement, levelness, and finished height of the Instrument.
Check for sufficient clearance around the Instrument, a 36" perimeter
around the Instrument is recommended for wheelchair accessibility.
Step 6:
If installing onto wet concrete, us the wet set anchor manufacturers
guidelines for installation procedures.
FREENOTES HARMONY PARK
194 BODO DRIVE, UNIT F
DURANGO CO 81303
TEL: (970) 375-7825
FAX: (970) 247-0856
WWW.FREENOTESHARMONYPARK.COM
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
FREENOTES HARMONY PARK. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF FREENOTES HARMONY
PARK IS PROHIBITED.
1
10
9
DETAIL C
SCALE 1 : 6
3/8" Drill Diameter
to a Depth of 4"
Concrete Pad
48"
30"
5
SWRL-INSTALL
6"
Surface Mount Installation
TITLE:
REVISION: B
SCALE: 1:16
DATE: 2/9/2018
SHEET 4 OF 4
DWG. NO.
Loading...