HARP
5
42
16
"
INSTALLATION GUIDE
3"
FREENOTES HARMONY PARK
194 BODO DRIVE, UNIT F
DURANGO CO 81303
TEL: (970) 375-7825
FAX: (970) 247-0856
WWW.FREENOTESHARMONYPARK.COM
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
FREENOTES HARMONY PARK. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF FREENOTES HARMONY
PARK IS PROHIBITED.
68
7
"
16
Main Features:
C Major Pentatonic
•
Powder Coated Steel Frame
•
Anodized Aluminum Chimes
•
Stainless Steel Hardware
•
Contents:
SHEET 2 - In Ground and Surface Mount
•
Installation w/ Parts List
Weights:
Instrument Weight, 111lbs.
•
Boxed Instrument Weight, 147lbs.
•
Harp - Installation Guide
TITLE:
REVISION: A
SCALE: 1:16
DATE: 2/8/2018
HRP-INSTALL
DWG. NO.
SHEET 1 OF 2
Parts List:
ITEM NO.
1
2
3
Step 1:
3/8"-16 Wedge Expansion Anchor, 3.75"lg. SS
Determine installation location. Verify concrete footing is a minimum of 36" long x 24" wide x 6" thick. If the concrete pad is at
PART DESCRIPTION
Harp Instrument Assembly
35/64" Hex Nut Cap
QTY.
1
6
6
an angle, steel washers are required to act as shims (Shims not provided). If there is not already an existing pad, approximately
(5) 80lb. bags will be needed. Allow concrete to cure per concrete manufacturers guidelines.
(
If a In-Ground appearance is desired recess the concrete pad 4" below finished grade)
Step 2:
With two people place the Instrument Assembly onto the concrete pad and mark the center of the holes on the surfacemount
plate. After you have made your marks, set aside the Instrument in order to drill for anchor holes. With a hammer or rotary drill,
drill through concrete at marked locations. Drill to a minimum depth of 4". A 3/8" masonry drill bit will be needed.
FREENOTES HARMONY PARK
194 BODO DRIVE, UNIT F
DURANGO CO 81303
TEL: (970) 375-7825
FAX: (970) 247-0856
WWW.FREENOTESHARMONYPARK.COM
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
FREENOTES HARMONY PARK. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF FREENOTES HARMONY
PARK IS PROHIBITED.
Step 3:
Place the Instrument back over the drilled out holes. Insert provided anchor
bolts into aligned holes. Position anchor nut so that it is flush with the top of
the bolt. Pound anchor bolts into the hole until the anchor washer is flush with
the steel base. Tighten anchor bolts until they are snug. Cover remaining bolt
sections with provided nut caps.
Step 4:
Verify the correct placement, levelness, and finished height of the instrument.
Also check for sufficient clearance around the instrument. A 36" perimeter
around the instrument is recommended for wheelchair accessibility.
Step 5:
If installing onto wet concrete, us the wet set anchor manufacturers
guidelines for installation procedures.
3
2
DETAIL A
SCALE 1 : 6
3/8" Drill Diameter
to a Depth of 4"
Concrete Pad
7"
36"
24"
1
HRP-INSTALL
7"
6"
In Ground and Surface Mount Installation
TITLE:
with Parts List
REVISION: A
SCALE: 1:16
DATE: 2/8/2018
SHEET 2 OF 2
DWG. NO.
Loading...