This drawing shows the locations of the warning
decals. If a decal is missing or illegible, call
the telephone number on the front cover of
this manual and request a free replacement
decal. Apply the decal in the location shown.
Note: The decals may not be shown at actual
size.
FREEMOTION is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and in-
tructions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
s
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or persons with
pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under age 12 and pets away
from the treadmill at all times.
other electrical devices, except for low-power
devices such as cell phone chargers, into the
surge suppressor or into an outlet on the
same circuit.
12. Use only a surge suppressor that meets all of
the specifications described on page 15. To
purchase a surge suppressor, see your local
FREEMOTION dealer, call the telephone number on the front cover of this manual, or see
your local electronics store.
13. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 26 if the treadmill is
not working properly.)
8. The treadmill should be used only by persons
weighing 350 lbs. (159 kg) or less.
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothes while
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
11. Plug the power cord into a surge suppressor
(not included), and plug the surge suppressor
into an appropriate outlet (see page 15). To
avoid overloading the circuit, do not plug
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 17).
17. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The heart rate monitor is not a medical device. Various factors, including the user's
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is intended only as an exercise aid in determining
heart rate trends in general.
3
0. Never leave the treadmill unattended while it
2
is running. Always remove the key, unplug
the power cord, and press the power switch
into the off position when the treadmill is not
in use. (See the drawing on page 5 for the location of the power switch.)
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 7, and HOW TO FOLD
AND MOVE THE TREADMILL on page 25.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
22. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
23. Never insert any object into any opening on
the treadmill.
SAVE THESE INSTRUCTIONS
4. Inspect and properly tighten all parts of the
2
treadmill regularly.
25.
DANGER: Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the mainte-
ance and adjustment procedures described in
n
this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
26. This treadmill is intended for home use only.
Do not use this treadmill in a commercial,
rental, or institutional setting.
27. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary
REEMOTION
F
an impressive selection of features designed to make
your workouts at home more enjoyable and effective.
And when you’re not exercising, the unique treadmill
an be folded up, requiring less than half the floor
c
space of other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Length: 6 ft. 8 in. (203 cm)
Width: 3 ft. (91 cm)
®
50 treadmill. The 750 treadmill offers
7
Handrail
Tray
ing this manual, please see the front cover of this man-
al. To help us assist you, please note the product
u
model number and serial number before contacting us.
The model number and the location of the serial number decal are shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Console
Heart Rate Monitor
Upright
Walking Belt
Foot Rail
Idler Roller
Adjustment Screws
Key/Clip
Power Switch
Power Cord
Platform Cushion
5
#8 x 3/4" Screw
(1)–12
3/8" Star
Washer (12)–4
3/8" Nut (11)–2
5/16" Star
Washer (10)–8
3/8" x 2 3/4" Screw (7)–4
3/8" x 1 3/4" Bolt (6)–1
3/8" x 2" Bolt (3)–1
#8 x 1/2" Ground
Screw (9)–1
3/8" x 1 1/4" Screw (8)–4
5/16" x 2" Screw (4)–4
5/16" x 1 1/2"
Screw (5)–4
PART IDENTIFICATION CHART
se the drawings below to identify small parts used for assembly. The number in parentheses below each draw-
U
ing is the key number of the part, from the PART LIST near the end of this manual. The number following the key
number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preat-
tached. Extra hardware may be included.
6
ASSEMBLY
• To hire a service technician to assemble this
product in your home, call 1-800-445-2480.
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you finish assembly.
• The underside of the walking belt is coated with
high-performance lubricant. After shipping, there
may be some lubricant on top of the walking belt
or on the shipping carton. This is normal. If there
is lubricant on top of the walking belt, wipe it off
with a soft cloth and a mild, non-abrasive cleaner.
1. Make sure that the power cord is unplugged.
Attach the Left Wheel Cap (96) to the left side of
the Base (97) with two #8 x 3/4" Screws (1).
Attach the Right Wheel Cap (not shown) to
the right side of the Base (97) in the same
way.
• To identify small parts, see page 6.
Assembly requires the following tools:
•
the included hex keys
one adjustable wrench
one Phillips screwdriver
To avoid damaging parts, do not use power tools
for assembly.
1
97
1
96
7
2. Pull the Upright Wire (84) and the Base Ground
Wire (94) through the indicated hole in the Base
(97).
Attach the Base Ground Wire (94) to the Base
97) with a #8 x 1/2" Ground Screw (9).
(
2
Hole
84
94
9
97
3. Identify the Left Upright (89), which is marked
“Left.” Have a second person hold the Left
Upright near the Base (97).
See the inset drawing. Tie the wire tie in the
Left Upright (89) securely around the end of the
Upright Wire (84). Then, pull the other end of the
wire tie until the Upright Wire is routed through
the Left Upright.
3
84
89
Wire
Tie
84
89
97
Wire
Tie
84
8
. Hold the Left Upright (89) against the Base
4
(97). Be careful not to pinch the wires. If necessary, position the Base Ground Wire (94) in
the hole in the side of the Left Upright. Insert
wo 3/8" x 2 3/4" Screws (7) and two 3/8" x
t
1 1/4" Screws (8) with two 3/8" Star Washers
(12) into the Left Upright. Note: It may be helpful to use the Hex Key (110) to insert the Screw
hat goes into the indicated hole.
t
4
Partially tighten the 3/8" x 2 3/4" Screws (7) and
the 3/8" x 1 1/4" Screws (8) until the heads of
the Screws touch the Left Upright (89); do notfully tighten the Screws yet. Note: It may be
helpful to use the Short Hex Key (63) on the
Screw shown.
Attach the Right Upright (not shown) in the
same way. Note: There are no wires on the
right side.
5. Identify the Left and Right Base Covers (92, 93).
Slide the Left Base Cover onto the Left Upright
(89). Slide the Right Base Cover onto the Right
Upright (90). Do not press the Base Covers
into place yet.
5
110
Hole
12
89
7
63
94
8
12
97
90
89
92
93
9
6. With the help of a second person, hold the console assembly near the Left Upright (89).
onnect the Upright Wire (84) to the console
C
wire. See the inset drawing. The connectors
hould slide together easily and snap into
s
place. If they do not, turn one connector and tryagain. IF YOU DO NOT CONNECT THE CONNECTORS PROPERLY, THE CONSOLE MAY
BECOME DAMAGED WHEN YOU TURN ON
THE POWER. Then, remove the wire tie from
the Upright Wire.
6
Console
Assembly
7. Insert the wires into the Left Upright (89) as you
set the console assembly on the Left and Right
Uprights (89, 90). Be careful not to pinch the
Upright Wire (84).
Attach the console assembly with four 5/16" x
1 1/2" Screws (5) and four 5/16" Star Washers
(10). Start all four Screws, and then tighten
each of them.
Console
Wire
84
7
Wire
Tie
84
Console
Wire
89
Console
Assembly
5
10
10
84
5
10
90
89
8. Identify the Left Handrail (87), which is marked
“Left.”
ttach the Left Handrail (87) to the console as-
A
sembly with two 5/16" x 2" Screws (4) and two
/16" Star Washers (10) as shown. Start both
5
Screws, and then tighten each of them.
8
Attach the Right Handrail (not shown) to the
console assembly as described above.
9. Attach a Tray Bracket (105) to the Right Upright
(90) using the two holes shown with two #8 x
3/4" Screws (1). Start both Screws, and then
tighten each of them.
Attach the other Tray Bracket (not shown) to
the Left Upright (not shown).
Attach the Tray (30) to the Tray Brackets (105)
with four #8 x 3/4" Screws (1) (only one side is
shown). Start all four Screws, and then
tighten each of them.
87
10
4
10
4
9
30
105
Console
Assembly
1
11
90
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.