Freeman PFN1564 User Manual

SAVE THIS MANUAL FOR FUTURE REFERENCE

MODEL: PFN1564

WARNING:

Failure to follow warnings could result in DEATH OR SERIOUS INJURY.

IMF100604AV 06/12

HTTP://WWW.FREEMANTOOLS.COM
1-888-669-5672
PRIME GLOBAL PRODUCTS, INC.

02

The warnings and precautions discussed in the manual cannot cover all possible conditions and
situations that may occur. It must be understood by the user that common sense and caution are
factors which cannot be built into this product, but must be supplied by the user.

WARNING:

SAVE THIS MANUAL

Keep this manual for the safety warnings,
precautions, operations, inspections and
maintenance.Keep this manual and the
receipt in a safe and dry place for future
reference.

SYMBOLS

In this manual, on the labels, packages and all other information provided with this tool. The following
signal words and meanings are intended to explain the levels of risk associated with this tool.

To avoid serious personal injury, do not
attempt to use this product until you read

thoroughly and understand it
completely. Save this manual and review
frequently for continuing safe operation
and instructing others who may use this
tool.

the manual

WARNING:

!

SYMBOLS SIGNAL MEANING

!
!

WARNING:

CAUTION:

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.

Indicates a potentially hazardous situation, which, if not avoided,
may result in minor or moderate injury.

(Without symbol) Indicates a situation that may result in
property damage.

●

●

GENERAL SAFETY RULES

WORK AREA

Keep the work area clean and well lighted.

Keep bystanders, children, and others away
while operating the tool.

Cluttered benches and dark areas increase the
risks of accidents.

Distractions could

result in improper use and cause injury.

Do not operate the tool in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust.

Avoid unintentional misfires.

The tool
creates a spark which may ignite flammable
liquids, gases or dust.

Always use
caution to avoid accidentally firing. Do not point
towards yourself or anyone whether it contains
fasteners or not.

●

●

●

●

INSTRUCTIONS PERTAINING TO A RISK OF
FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS

CALIFORNIA PROPOSITION 65

WARNING:

!

When using tools, basic precautions
should always be followed, including the
following:

WARNING:

!

This product or its power cord may
contain chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.

HTTP://WWWFREEMANTOOLSCOM 1-888-669-5672..

MODEL: PFN1564 MODEL: PFN1564

HTTP://WWWFREEMANTOOLSCOM 1-888-669-5672..

P2
P5
P5

P6
P6
P6
P6
P7
P7
P7
P7
P8
P8
P9
P10
P10
P11

GENERAL SAFETY RULES
UNPACKING
FEATURES
OPERATION

MAINTENANCE
RECOMMENDED HOOKUP
TROUBLESHOOTING
WEARING PARTS
WARRANTIES

USING BELT HOOK
ADJUSTING THE EXHAUST
LOADING FASTENERS
UNLOADING FASTENERS
CLEARING JAMS
NO-MARRING PAD
SETTING THE AIR PRESSURE
DEPTH ADJUSTMENT
FIRING THE TOOL

01

PERSONAL SAFETY

Do not nail on top of another nail.

Remove finger from the trigger when not
driving fasteners.

This is
able to cause the nail to be deflected and hit
someone, or cause the tool to react and result in
a risk of injury to persons.

Never carry the tool with
finger on trigger, the tool is able to fire a
fastener.

Always wear eye protection.

Always wear hearing protection when
using the tool.

Use safety equipment.

Dress properly. Do not wear loose clothing
or jewelry.

Stay alert, watch what you are doing and
use common sense when operating a
power tool.

Avoid unintentional firing. Keep fingers
away from trigger when not driving
fasteners, especially when connecting the
tool to the air supply.
Keep proper footing and balance at all times.

Operator and
others in the work area should always wear
ANSI-approved safety goggles with side
shields. Eye protection is used to guard against
flying fasteners and debris, which may cause
severe eye injury. You can use the goggles
packed with the tool.

Prolonged exposure to high

intensity noise may cause hearing loss.

A dust mask, non-skid
safety shoes and a hard hat must be used for
the applicable conditions. Wear a full face shield
if you are producing metal filings or wood chips.

Contain long hair. Keep your hair,
clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be
caught in moving parts.

Do not use tool while tired or under
the influence of drugs, alcohol, or medication. A
moment of inattention while operating the tool
may cause serious injury.

Proper footing and balance enables better
control of the tool in unexpected situations.

0403

HTTP://WWWFREEMANTOOLSCOM 1-888-669-5672..

MODEL: PFN1564 MODEL: PFN1564

HTTP://WWWFREEMANTOOLSCOM 1-888-669-5672..

Know this tool. Read manual carefully, learn
its applications and limitations, as well as the
specific potential hazards related to this tool.

Use only fasteners that are recommended
for your models.

Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tool's
operation.

Maintain tools with care.

Store tools out of the reach of children and
other untrained people.

Check operation of the tool before use.

Do not use tool if trigger does not actuate
properly.

Do not force tool.

Use clamps or another practical way to

Do not use the wrong

fasteners or load the fasteners incorrectly.

If damaged, have the tool serviced
before using. Many accidents are caused by
poorly maintained tools.

Keep tool clean. A
properly maintained tool, reduces the risk of
binding and is easier to control.

Tools are dangerous

in the hands of untrained users.

Do
not use the tool if the workpiece contact
mechanism is not working correctly as
accidental driving of a fastener may occur.

Any tool that cannot be controlled
with the trigger is dangerous and must be
repaired.

Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it is designed.

TOOL SERVICE

Use only accessories that are identified by
the manufacturer for the specific tool model.
Use of unauthorized parts or failure to
follow maintenance instructions may create
a risk of injury.
Use only the lubricants supplied with the
tool or specified by the manufacturer.
Tool service must be performed only by
qualified repair personnel.

OPERATION

Do not drive fasteners near edge of material.

The workpiece may split causing the fastener or
ricochet, injuring you or people around.

Do not carry the tool from place to place
holding the trigger. Accidental discharge
could result.

During normal use the tool will recoil
immediately after driving a fastener.

Do not drive fasteners on top of other
fasteners or with the tool at an overly steep
angle as this may cause deflection of
fasteners which could cause injury.

Choice of triggering method is

important. Check manual for triggering options.

This is
a normal function of the tool. Do not attempt to
prevent the recoil by holding the tool against the
work. Restriction to the recoil can result in a
second fastener being driven from the tool. Grip
the handle firmly and let the tool do the work.
Failure to heed this warning can result in serious
personal injury.

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

Secure and support the workpiece to a
stable platform. Holding a tool by hand or

against the body is unstable and may lead to
loss of control.

Keep the tool and its handle dry, clean and
free from oil and grease.

Do not use the tool as a hammer.
Never use this tool in a manner that could
cause a fastener to be directed toward
anything other than the workpiece.
Never use gasoline or other flammable
liquids to clean the tool.

Do not remove, tamper with, or otherwise
cause the trigger lock or trigger to become
inoperable.

Do not touch the trigger unless driving
fasteners.

Always fit tool with a fitting or hose
coupling on or near the tool in such a
manner that all compressed air in the tool is
discharged at the time the fitting or hose
coupling is disconnected.

Never place hands or any other body parts
in the fastener discharge area of the tool.

Never carry the tool by the air hose or pull
the hose to move the tool or a compressor.

Always assume the tool contains fasteners.

Always keep others at a safe distance from
the work area in case of accidental
discharge of fasteners.

Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products, or any
strong solvents to clean your tool.

Never use the tool in
the presence of flammable liquids or gases.
Vapors could ignite by a spark and cause an
explosion which will result in death or serious
personal injury.

Do not operate any tool which has
been modified in a like fashion. Death or
serious personal injury could result.

Never attach air line to tool or carry
tool while touching the trigger. The tool could
eject a fastener which will result in death or
serious personal injury. Also actuate the trigger
lock to the safe position when not in use.

Do not use a check
valve or any other fitting which allows air to
remain in the tool. Death or serious personal
injury could occur.

The tool might eject a fastener and could result
in death or serious personal injury.

Keep hoses away from heat, oil and sharp
edges. Replace any hose that is damaged,
weak or worn. Personal injury or tool damage
could occur.

Respect the tool as a working implement; no
horseplay.

Do not point the tool

toward yourself or anyone whether it contains

●

●

●

●

●

fasteners or not. Accidental triggering of the tool
could result in death or serious personal injury.

Do not drop or throw the tool.

Avoid using the tool when the magazine is
empty.

Clean and check all air supply hoses and
fittings before connecting the tool to an air
supply.

Do not use th

Dropping or
throwing the tool can result in damage that will
make the tool unusable or unsafe. If the tool has
been dropped or thrown, examine the tool
closely for bent, cracked or broken parts and air
leaks. STOP and repair before using, or serious
injury could occur.

Accelerated wear on the tool may

occur.

Replace any damaged or worn hoses
or fittings. Tool performance or durability may
be reduced.

e tool if it leaks air or does not
function properly.
Do not operate the tool if it does not contain
a legible warning label.
Always carry the tool by the handle. Never
carry the tool by the air hose.

●

●

Do not actuate the tool unless you intend to
drive a fastener into the workpiece.
Always handle the tool with care:

◆Respect the tool as a working implement.

◆Never pull the trigger unless nose is directed

toward the work.

◆Never engage in horseplay.

◆Keep others a safe distance from the tool

while tool is in operation as accidental
actuation may occur, possibly causing injury.

●

●

AIR SUPPLY AND CONNECTIONS

The connector on the tool must not hold
pressure when air supply is disconnected.

Do not use any type of reactive gases,
including, but not limited to, oxygen and
combustible gases, as a power source.

Use only a pressure-regulated compressed
air source to limit the air pressure supplied
to the tool.

If
an incorrect fitting is used, the tool can remain
charged with air after disconnecting and thus
will be able to drive a fastener even after the air
line is disconnected, possibly causing injury.

Use
filtered, lubricated, regulated compressed air
only. Use of a reactive gas instead of
compressed air may cause the tool to explode
which will cause death or serious personal
injury.

The regulated pressure must not
exceed 100 psi. If the regulator fails, the
pressure delivered to the tool must not exceed
200 psi. The tool could explode which will cause
death or serious personal injury.

Always disconnect air source:

●

●

●

●

LOADING TOOL

Do not load the tool with fasteners when
any one of the operating controls is
activated.
Never place a hand or any part of body in
fastener discharge area of tool.
Never point tool at anyone.
Do not pull the trigger or depress the
workpiece contact as accidental actuation
may occur, possibly causing injury.

●

●

●

●

●

●

TOOL USE AND CARE

●

●

●

●

●

●

●

●

●

Do not use on a ladder or unstable supports.

Make sure the hose is free of obstructions
or snags.

Do not overreach. Keep proper footing and
balance at all times. Proper footing and
balance enables better control of the tool in
unexpected situations.
Do not attach the hose or tool to your body.
Attach the hose to the structure to reduce
the risk of loss of balance if the hose shifts.
Always assume that the tool contains
fasteners. Do not point the tool toward
yourself or anyone whether it contains
fasteners or not.
Wash hands after handling. This product or
its power cord may contain chemicals
known to the State of California to cause
cancer and birth defects or other
reproductive harm.

Stable footing on a solid surface enables better
control of the tool in unexpected situations.

Entangled or snarled hoses can
cause loss of balance or footing and may
become damaged, resulting in possible injury.

Before unloading or making adjustments.
When maintaining the tool.
When clearing a jam.
When touching the safety yoke.
When tool is not in use.
When moving to a different work area.

Such precautionary measures reduce the risk of
injury to persons.

0605

The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.

WARNING:

!

UNPACKING

This tool has been shipped completely
assembled.
Carefully remove the tool and any
accessories from the box.
Inspect the tool carefully to make sure no
breakage or damage occurred during
shipping.
Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
If any parts are damaged or missing, please
call 1-888-669-5672.

●

●

●

●

●

If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.

WARNING:

!

Do not attempt to modify this tool or
create accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result
in hazardous condition leading to
possible serious personal injury.

WARNING:

!

Compatible with all brands of 15 gauge 34°
2-1/2" angle finish nails.

FEATURES

SPECIFICATIONS

REQUIRES:

AIR INLET:
MAGAZINE CAPACITY:

WEIGHT:
MAXIMUM PRESSURE:
PRESSURE RANGE:

9.39 SCFM with 100

fasteners per minute @ 90 psi

1/4 inch NPT

100 fasteners, 15 gauge

4.75 lbs
110 psi

70 psi 110 psi–

PIN SIZE RANGE: 1-1/4" to 2-1/2"

FEATURES

360 ADJUSTABLE EXHAUST

Allows user to direct air away from face.

OIL-FREE DESIGN
ONE PIECE DRIVER BLADE
ANODIZED ALUMINUM CYLINDER AND

MAGAZINE
COMFORT-GRIP HANDLE
ERGONOMICALLY ENGINEERED BODY

AIR FILTER

DUAL-MODE TRIGGER
ADJUSTABLE DEPTH

QUICK-JAM RELEASE

NON-MARRING SAFETY CONTACT

For less maintenance.
For increased durability.

For long lasting durability.
For increased comfort and control.
Rugged and Comfortable resulting in a light-

weight tool great for extended use.
Keeps interior components debris free,

extending tool life.
Easily allows for Single or Sequential Firing.
Depth is easily adjustable for various

applications.
Allows for easy access clearing in the event of

a jam.
Eliminates damage to working surfaces.

OPERATION

USING BELT HOOK

The tool is packed with a separate hook system.
Assemble the hook on the tool before using the
hook. The hook should be positioned on right side.

Loosen and remove the hook screw and nut(A).
Save the screw and nut for future use.
Position the hook on right position. Using the
longer screw packed with hook, fasten hook to
tool.

Hook nut(A)

1.

2.

ADJUSTING THE EXHAUST

The adjustable exhaust on the cap of the tool allows
users to direct the exhaust according to operator
preference. To adjust the direction, turn the exhaust
cap in the desired direction.

Connect the tool to the air source.
Pull pusher(B) back until the fasteners follower
falls behind the fasteners. Insert strip of
fasteners into rear of magazine(C). Be sure the
fasteners are pointed downward .
Pull pusher to let it go back to move the
fasteners up to the driving mechanism. The
pusher will stop when it rests against the end of
the fastener.

⒈
⒉

⒊

LOADING FASTENERS

Pusher(B)

Rear of magazine(C)

The tool may fire when it first connected
to the air source. Always connect the tool
to the air source before loading fasteners
to prevent injury from unintended cycling.
Always make sure the tool's magazine is
empty at the beginning of each work
session, before connecting to an air
source.

WARNING:

!

Never load fasteners with the workpiece
contact or trigger activated. Doing so
could result in possible serious personal
injury.

WARNING:

!

Keep the tool pointed away from yourself
and others when loading fasteners.
Failure to do so could result in possible
serious personal injury.

WARNING:

!

UNLOADING FASTENERS

Unloading is the reverse of loading, except always
disconnect the air source before unloading.

HTTP://WWWFREEMANTOOLSCOM 1-888-669-5672..

MODEL: PFN1564 MODEL: PFN1564

HTTP://WWWFREEMANTOOLSCOM 1-888-669-5672..

Use only those fasteners recommended
for use with this tool. Fasteners not
identified for use with this tool by the tool
manufacturer are able to result in a risk of
injury to persons or tool damage when
used in this tool.

WARNING:

!

32mm
38mm
45mm

50mm
57mm
64mm

1-1/4”
1-1/2”

1-3/4”

2”
2-1/4”
2-1/2”

0807

Always unload all fasteners before removing
tool from service.

WARNING:

!

Always disconnect the air source before
unloading.

WARNING:

!

CLEARING JAMS

Disconnect the tool from air source.
Remove fasteners from the tool. Failure to do
so will cause the fasteners to eject from the front
of the tool.
Pull and open the jam release(D).
Using caution not to bend or damage the driver
blade, using pliers or a screwdriver if required to
clear the jammed fastener.
Close the jam release(D).
Reconnect the tool to the air source.
Reload the tool with fasteners.

Occasionally, a fastener may become jammed in
the firing mechanism of the tool, making the tool
inoperable. To remove a jammed fastener, follow
the steps below:

1.

2.

⒊
⒋

⒌
⒍
⒎

Jam release(D)

Make sure there is no fastener in
magazine before clearing a jam.

WARNING:

!

Disconnect the tool from the air source
whenever clearing a jam. After
disconnecting the tool from the air
compressor, there should still be enough
air pressure to fire the tool. After the air
hose is disconnected, always fire the tool
into scrap wood repeatedly to make sure
all of the compressed air is expended.

WARNING:

!

SETTING THE AIR PRESSURE

The amount of air pressure required depends on
the size of the fasteners and the workpiece material.
Begin testing the depth of drive by driving a test nail
into the same type of workpiece material used for
the actual job.
Drive a test fastener with the air pressure set at 90­95psi. Raise or lower the air pressure to find the
lowest setting that will perform the job with
consistent results.
It may be possible to achieve the desired depth with
air pressure adjustments alone.

NO-MARRING PAD

The no-marring pad attached the nose of the tool
helps prevent marring and denting when working
with softer woods.

Disconnect the tool from the air source
before removing or replacing the no­marring pad or replacing the no-marring
pad. Failure to do so could result in serious
personal injury.

WARNING:

!

DEPTH ADJUSTMENT

The driving depth of the fasteners are adjustable.
To adjust the depth, use the drive depth adjustment
wheel(E) on the tool.

Disconnect the tool from the air source.
Turn the depth wheel left or right to change the
driving depth.
Reconnect the tool to the air source.
Drive a test nail after each adjustment until the
desired depth is set.

1.

2.

⒊
⒋

Adjustment wheel(E)

FIRING THE TOOL
(USING THE SELECTABLE TRIGGER)

The tool is with a selectable trigger set in the single
sequential actuation mode. The selectable trigger
can also be set for contact actuation mode.

Single sequential actuation provides the most
accurate fastener placement.

SINGLE SEQUENTIAL ACTUATION MODE

It is advisable to test the depth on a scrap
workpiece to determine the required
depth for the application.
To determine depth of drive, first adjust
the air pressure and drive a test fastener.
Never exceed 120 psi.

CAUTION:

Disconnect the tool from the air source.
Rotate the selector to one single nail position(F).
Reconnect the tool to the air source.
Grip the tool firmly to maintain control. Position
the nose of the tool onto the work surface.
Push the tool against the work surface to
depress the workpiece contact.
Squeeze the trigger to drive a fastener.

1.

2.

⒊
⒋

⒌

⒍

Disconnect the tool from the air source.
Rotate the selector to two nails position(G).
Reconnect the tool to the air source.
Grip the tool firmly to maintain control. Position
the nose of the tool onto the work surface.
Squeeze and hold the trigger, push the tool
against the work surface to depress the
workpiece contact and drive a fastener.

Contact actuation allows for very fast, repetitive
fastener placement.

1.

2.

⒊
⒋

⒌

CONTACT ACTUATION MODE

Two nails position(G)

Single nail position(F)

In the contact actuation mode, the tool may also be
operated by depressing the workpiece contact
against the surface and squeezing the trigger.

During normal use the tool will recoil
immediately after driving a fastener. This
is a normal function of the tool. Do not
attempt to prevent the recoil by holding
the tool against the work. Restriction to
the recoil can result in a second fastener
being driven from the tool. Grip the
handle firmly and let the tool do the work.
Failure to heed this warning can result in
serious personal injury.

WARNING:

!

MAINTENANCE

Any time inspection, maintenance, and
cleaning are done:

◆Disconnect the tool from the air source.
Empty the magazine completely.◆

WARNING:

!

Each tool is packed with an anti-dust cap on the air
connector.
Keep the anti-dust cap cover the air connector
when the tool is not in use.

The tool is uniquely designed not to need daily
lubrication. But lubrication is required for best
performance after long periods use. Oil for
pneumatic fastening tools is added through the air
line connection and will lubricate internal parts. Do
not use detergent oil or additives as these lubricants
will cause accelerated wear to the seals and
bumpers in the tool, resulting in poor tool
performance and frequent tool maintenance.

LUBRICATION

ANTI-DUST CAP

HTTP://WWWFREEMANTOOLSCOM 1-888-669-5672..

MODEL: PFN1564 MODEL: PFN1564

HTTP://WWWFREEMANTOOLSCOM 1-888-669-5672..

1009

Lubricate tool only with specified
lubricants.

CAUTION:

Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from
various types of commercial solvents and maybe
damaged by their use. Use clean cloths to remove
dirt, dust , oil, grease, etc.

CLEANING

Do not at any time let brake fluids,
gasoline, petroleum-based products,
penetration oils, ect. come in contact
with plastic parts. Chemicals can damage,
weaken or destroy plastic which may
result in serious personal injury.

WARNING:

!

Do not store tools in a cold weather
environment to prevent frost or ice
formation on the tool's operating valves
and mechanisms that could cause tool
failure.

CAUTION:

COLD WEATHER OPERATION

For cold weather operation, near and below
freezing, the moisture in the air line may freeze and
prevent tool operation. We recommend the use of
air tool lubricant or permanent antifreeze (ethylene
glycol) as a cold weather lubricant.

RECOMMENDED HOOKUP

The air compressor must be able to
maintain a minimum of 60 psi when the
tool is being used. An inadequate air
supply can cause a loss of power and
inconsistent driving.

CAUTION:

Do not connect with an air compressor
which can potentially exceed 200 psi. As
tool may burst, possibly causing injury.

WARNING:

!

The air compressor must be able to maintain a
minimum of 70 psi when the tool is being used.
An inadequate air supply can cause a loss of
power and inconsistent driving.
An oiler can be used to provide oil circulation
through the tool. A filter can be used to remove
liquid and solid impurities which can rust or gum
up internal parts of the tool.
Always use air supply hoses with a minimum
working pressure rating equal to or greater than
the pressure from the power source if a
regulator fails, or 150 psi, whichever is greater.
Use 3/8" air hose for runs up to 50'. Use 1/2" air
hoses for 50' run or longer. For better
performance, install a 3/8" quick plug (1/4" NPT
thread) with an inside diameter of .315" (8mm)
on the tool and 3/8" quick coupler on the air
hose.
Use a pressure regulator on the compressor,
with an operating pressure of 0-125 psi. A
pressure regulator is required to control the
operating pressure of the tool between 70 and
110 psi.

TROUBLESHOOTING

Stop using tool immediately if any of the following problems occur. Serious personal injury
could result. Any repairs or replacements must be done by a qualified service person or an
authorized service center.

WARNING:

!

Air leaking at trigger
valve area.

O-rings in trigger valve housing are
damaged

Replace o-rings. Check operation
of Work Contact Element(WCE)

Air leaking between
housing And nose.

Loose screws in housing

1.Damaged O-rings

2.Damaged to bumper

Tighten screws

1.Replace o-rings

2.Replace bumper

Air leaking between
housing and Cap.

1.Loose screws

2.Damaged gasket

1.Tighten screws

2.Replace gasket

1.Replace bumper

2.Clean drive channel

3.Clean magazine

4.Replace spring

5.Check fitting, hose, or compressor

6.Replace and lubricate o-rings

7.Replace o-rings

8.Tighten screws and fittings

9.Replace gasket

1.Worn bumper

2.Dirt in nose piece

3.Dirt or damage prevent fasteners or
pusher from moving freely in magazine

4.Damaged pusher spring

5.Inadequate air flow to tool

6.Worn O-ring on piston or lack
of lubrication

7.Damaged O-ring on trigger valve

8.Air leaks

9.Cap seal leaking

Tool skips driving
fastener

PROBLEMS POSSIBLE CAUSE(S) CORRECTIVE ACTION

1.Lubricate nailer

2.Replace spring

3.Replace damaged internal parts

1.Tool not lubricated sufficiently

2.Broken spring in cylinder cap

3.Exhaust port in cap is blocked

Tool runs slow or has
loss of power

1.Replace guide

2.Use only recommended fasteners

3.Replace with undamaged fasteners

4.Tighten screws

5.Replace driver

1.Guide on driver is worn

2.Fasteners are not correct size

3.Fasteners are bent

4.Magazine or nose screws are loose

5.Driver is damaged

Fasteners are jammed
in tool

Use only Freeman Authorized Repair Parts. For questions please call 1-888-669-5672 or visit
our website at http://www.freemantools.com

WARNING:

!

WEARING PARTS

Repair parts can be ordered from our website: http://www.freemantools.com

1.

2.

3.

4.

HTTP://WWWFREEMANTOOLSCOM 1-888-669-5672..

MODEL: PFN1564 MODEL: PFN1564

HTTP://WWWFREEMANTOOLSCOM 1-888-669-5672..

FREEMAN

Professional 7-Year Limited Warranty

Professional 90 Day Limited Warranty

This warranty of Freeman Nail Guns extends exclusively to the original purchaser of the Freeman Nailing Gun seven(7)
years from the original purchase date. PGP Inc. expressly warrantsthattheFreemanNailGunisfreefromdefectin
materialsandworkmanshipsubjecttotheexceptionsandlimitationscontainedherein

This warranty of PGP Inc.s driver blades, bumpers, o-rings, pistons, piston rings,andgasketstheFreeman Wearing
PartscollectivelywiththeFreemanNailingGunstheFreeman Productextendsexclusivelytotheoriginalpurchaserof
theFreemanWearingPartsninetydaysfromtheoriginalpurchasedateduetoadefectinmaterial and workmanship.

PGP Inc. shall repair or replace, at its option, a Freeman Product that has a defect in materials or workmanship. The
original purchaser must return the complete Freeman Product, postage prepaid and insured, with proof of purchase to
PGP Inc. or any of its authorized service centers. Other than the postage and insurance requirement, no charge will be
made for repairs covered by this warranty.

These warranties do not apply to defects in materials or workmanship or damages resulting from repairs or alterations
which have been made or attempted by others or the unauthorized use of nonconforming parts. They further do not apply if
the damage is due to normal wear and tear, abuse, improper maintenance, neglect or accident or caused by use of the
Freeman Product after partial failure or use with improper accessories.

The Freeman Product is intended for use by individuals and not for use on an assembly line, production line, or any
commercial application. These warranties do not extend to such commercial use as it constitutes abuse of the Freeman
Product.

These warranties are the sole and exclusive warranties, express or implied for the Freeman Product. No employee, agent,
dealer or other person is authorized to alter, modify, expand or reduce the terms of these warranties or to make any other
warranty on behalf of PGP Inc. These express limited warrantiescontainstheentireagreementregardingexpressand
impliedwarrantiesrelatedtotheFreeman Product. No writing or languages in the purchase order or any other document
shall be construed as an addition or alteration of PGP Inc.s warranties of the Freeman Product.

All matters related to the sale and/or use of the Freeman Product that is the subject of these limited warranties, along with
the construction and enforcement of the terms of these limited warranties themselves, shall be subject to the laws of the
state of Georgia. Any dispute arising out of the sale and/or use of the Freeman Product that is the subject of these limited
warranties shall be brought in Cherokee County, Georgia. Purchase and/or use of the Freeman Product, makes you
subject to the benefits and limitations of these limited warranties. Accordingly, any writ, judgment or other enforcement,
obtained from a jurisdiction, county, parish, state or federal court or other country, other than from the forum identified
above, shall be void and unenforceable against PGP Inc.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.

If any term or limitation contained in this limited warranty is deemed unenforceable by law, then that term shall be severed
from the remaining portions of the limited warranties which shall remain enforceable.

.

' ( "

" "")

(90)

,

'

NO WARRANTY, ORAL OR WRITTEN, EXPRESSED OR IMPLIED, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS FREEMAN PRODUCT. PGP INC. DISCLAIMS ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR
PURPOSE, AND ALL OTHER WARRANTIES. IN NO EVENT SHALL PGP INC. BE LIABLE FOR ANY
INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS,
ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF
ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED
TO, ANY CLAIMS FOR LOSS OF PROFITS.

THESE WARRANTIES ARE SUBJECT TO CHANGE WITHOUT NOTICE.

PGP INC. PRODUCT WARRANTIES

11

HTTP://WWWFREEMANTOOLSCOM 1-888-669-5672..

MODEL: PFN1564

MODELO: PFN1564

GUARDA ESTE MANUAL PARA CONSULTARLO EN EL FUTURO.

ADVERTENCIA:

No seguir las advertencias correctamente puede causar
LA MUERTE O LESIONES GRAVES.