Freedom Oslo Desk 1600 Assembly Instruction
OSLO
DESK 160cm
(O-DSK16)
Before you begin to assemble your new piece of furniture please check to ensure all parts and fittings have been supplied. Follow all
instructions closely as deviation from them may void warranty and present possible safety risk. It is recommended that assembly is done on a
soft surface, like carpet, to avoid damage. CARE INSTRUCTIONS: Periodically re-tighten all fasteners. TOOLS REQUIRED: Allen key (provided),
screwdriver. Some packs may come with timber of a different colour to the model purchased. These pieces are for packing purposes only.
If you experience any problems with your new purchase please phone our Customer Service staff on (FREE CALL PHONE / FAX) 1800 029 715
Please keep last page of the instruction for warranty information.
CLEANING AND MAINTENANCE: Do not use solvent or alcohol based cleaners on this unit. To clean unit, we recommend using a
warm damp cloth to wipe over surfaces.
PARTS CHECKLIST
CODE PART QTY SIZE
A TOP 1 1495 x 703
F
A
B
B RIGHT SIDE 1 727 x 710
C UPRIGHT 1 366 x 445
D RAIL 1 425 x 96
E LEFT SIDE 1 727 x 710
F COURTESY PANEL 1 1495 x 368
C
G DRAWER FRONT 2 168.5 x 419
E
FITTINGS CHECKLIST
CODE DESCRIPTION FITTING QTY CODE DESCRIPTION FITTING QTY
50-001 WOODEN DOWEL 15 50-140 CAM COVER 1
D
H
I
K
J
G
2 PERSON RECOMMENDED
ASSEMBLY
H RIGHT DRAWER SIDE 2 336 x 120
I DRAWER BACK 2 375 x 120
J LEFT DRAWER SIDE 2 336 x 120
K DRAWER BASE 2 328 x 387
50-009 ALLEN KEY 1 50-167 SCREW M4 x 22mm 4
50-010 EURO SCREW 8 50-301 DWR BASE SUPPORT 2
50-011 SCREW CSK 6g x 1/2" 8 50-450 LAG BOLT 2
50-015 MINIFIX CAM 10 51-005 350mm RUNNER SET 2
50-016 METAL DOWEL 14 51-183 NAIL ON GLIDE 2
50-043 HI-LO SREW 8 51-225 80mm FOOT 2
50-152 WEDGE (SNAP OFF) 2 51-500 WAVE HANDLE 2
50-136 MICROFIX CAM 4 80-001 GLUE BOTTLE 1
CODE: O-DSK16 MADE IN AUSTRALIA BY KD CONCEPTS
PAGE 1 OF 5
STEP 1: PREPARE FEET FITTINGS
50-490
x 2
51-225
x 2
x 2
STEP 2: PREPARE RIGHT SIDE
STEP 2: PREPARE RIGHT SIDE
50-016
x 3
50-183
x 1
FOOT FROM
STEP 1
B
STEP 3A: PREPARE LEFT SIDE (RUNNERS)
50-010
x 4
E
50-005
POSITION OF SCREWS AND HOLES FOR RUNNER FIXING
LEFT RUNNER SHOWN
STEP 4: PREPARE PARTITION
50-001
x 3
50-010
x 4
APPLY SMALL AMOUNT
OF GLUE TO DOWELS
50-015
x 2
50-016
x 2
STEP 3B: PREPARE LEFT SIDE (HARDWARE)
50-016
x 4
50-183
x 1
E
FOOT FROM
STEP 1
STEP 5: PREPARE RAIL
50-015
x 2
APPLY SMALL AMOUNT
OF GLUE TO DOWELS
50-001
x 2
ARROW OF CAM
MUST POINT TO
EDGE
C
50-005
CODE: O-DSK16 MADE IN AUSTRALIA BY KD CONCEPTS
D
PAGE 2 OF 5
Loading...