Precision
Powder Scale
Precision
Powder Scale
Product #909672
Instructions #1028773
USER MANUAL
Please read all operating instructions carefully before use. This electronic
scale is a precision instrument. With normal care and proper treatment,
it will provide years of reliable service.
ATTENTION!
• Never load the scale with more than the maximum capacity.
Overloading can permanently damage unit.
• Handle with care. Gently apply all items to be weighed onto
tray top. Although this scale is designed to be quite durable,
try to avoid rough treatment as this may permanently
damage the internal sensor
• Avoid shaking, dropping or otherwise shocking the scale.
This is a precision instrument and must be handled with care.
TROUBLESHOOTING
e primary reasons for inaccuracy or malfunction are low batteries,
incorrect calibration, overload or operating on an unstable surface. Please
keep these in mind and maintain and operate your scale properly. e scale
is a precise instrument and must be handled with care and caution.
Display Elimination of errors
Nothing Battery-symbol, [lo] or [8888] Change the batteries.
[OUT2] Recalibrate the scale as shown above.
[O-LD] You are overloading the scale.
Remove the excessive load immediately!
[LLLLL] e delicate weighing load cells have been damaged by misusing
the scale (i.e. it was shocked, dropped or overload.) You can try
recalibrating the scale. If the load cell has not been damaged
it will work again aer recalibration.
[UNST] Use the scale in a more stable position
CONTENTS
A. Precision scale
B. 2 calibration weights
C. Powder pan
D. Podium
E. Clear cover
F. Storage case (NOT SHOWN)
G. 110V power supply
H. 220V adaptor
A.
B.
C.
D.
E.
G.
H.
e Platinum Series Powder Scale is a very precise measuring instrument.
We recommend using the scale on a at and sturdy table top in a clean
environment. e presence of dirt, dust, moisture, vibrations, air currents
or use in close proximity of other electronic devices can cause adverse
eects on the reliability and accuracy of the scale. It is also recommended to
avoid exposing the scale to extreme heat or cold, the scale works best when
operated at normal room temperature. For the best results we recommend
calibrating the scale every reloading session. (See Calibration Instructions
below) Aer powering on wait 30-60 seconds to allow internal components
the chance to stabilize before calibrating.
1. Press POWER button.
2. Wait 1 minute for internal components to stabilize.
3. Calibrate the unit if desired.
4. Wait until [0.000] is displayed.
5. Put the object (s) on the weighing platform.
6. Using the UNITS button, you can switch between weighing units.
OPERATION
1. Turn on the scale as described above.
2. Place the “tare item” on the platform.
3. Press ZERO button quickly and [0.000] is displayed.
4. Add the “net-weight-item”.
TARE WEIGHTING
1. Press POWER button to turn on the scale. (Wait 30-60 seconds)
2. Wait until “0.000” is displayed, press and hold CAL button for two seconds.
It will display and ash “CAL”.
3. en the LCD will ash 0.000 rst to set zero point, for which you don’t
need to put any weight on the platform. Aer two seconds, it will ash
the second weight 50.000, place the required weight onto the platform,
and then it will ash the third weight 100.00, place the required
weight onto the platform.
4. e display will show “PASS” and return to normal weighing mode.
Calibration is complete.
NOTE: Repeat this process if PASS is not displayed.
CALIBRATION
Capacity: ......... 1543.2gn/100g/3.527oz/500.00ct
Readability: ....... 0.1gn/0.01g/0.001oz/0.05ct
Units: ............ gn/g/oz/ct
Auto o time: ..... 180 seconds
Operation temp: ...10C-30C
SPECIFICATIONS
Power: ........... 4x ‘AAA’ Batteries (not included)
Or .............. AC to 5V adapter (included)
Dimensions: ...... 200 x 125 x 60mm
Weight: ........... 540g
Loading...