Franke FTU 3807 I XS 77H Tube Island, Tube Island Handbook

HANDBOOK HOOD FTU 3807 I XS 77H 9925289 110.0018.185

UPDATED JANUARY 2010

4 SPEED + INTENSIVE

ELECTRONIC PUSH- BUTTONS 4 SPEED + INTENSIVE+ DELAY TIMER+ TO SET UP THE MOTOR
TO A SUCTION SPEED AT 100 M3/H LASTING 10 MINUTES EVERY HOUR+ TURNS LIGHT ON AND
OFF AT REDUCED INTENSITY.

M3/H800 -
DBA 67 -
W 370 -
2 HALOGEN LAMPS X 20 W = TOTAL POWER 40 W

Key Function Display
A Switches the extractor motor on and off at the

latest selected speed

Indicates the selected speed.

B Decreases the suction speed.
C Increases the suction speed.
D By pressing this key it is possible to activate the

intensive speed from any previously selected
speed. The intensive speed can be activated even
when the motor is OFF. This speed has been
timed at 10 minutes. After that time the system
activates automatically the latest selected speed.
This function is suitable for cooking conditions
when vapours and smells are of the utmost
emission.

HI appears. The spot down on the right side flashes
once a second.

E By pressing this key it is possible to set up the

motor to a suction speed at 100 m3/h lasting 10
minutes every hour. After this the motor switches
off automatically. When the filter saturation is
going on it is possible to reset the alarm by
pressing this key for about 3 seconds. The
indication is visible only when the motor is off.

Indicates the 24-function. The spot down on the right
side flashes and the motor is on.
Once the process is finished the previous indication
disappears:
FF Indicates that the metal grease filters
saturation alarm has been triggered, and the filters
need to be washed. The alarm is triggered after 100
working hours.
EF Indicates that the charcoal filter saturation
alarm has been triggered, and the filter has to be
replaced; the metal grease filters must also be
washed. The charcoal filter is triggered after 200
working hours.

F By pressing this key it is possible to set the

delayed shutdown of the appliance to 30 minutes.
This function is suitable for a complete elimination
of the residual smells. It can be activated at any
position, and it is deactivated by pressing the key
again or by switching off the motor.

Indicates alternately the selected speed of the hood
and the time left before the hood shutdown. The
spot down on the right side flashes.

G Turns light on and off.
H Turns light on and off at reduced intensity.

Metal grease filters

Filters can be washed in the dish machine. They need to be washed when FF-sign appears on the display or in any
case every 2 months, or even more frequently in case of particularly intensive use of the hood. Alarm reset

• Switch off the hood and the lights. If the 24h-function has been activated this has to be deactivated.

• Press the E-key till the display is unlit. Cleaning the filters

• Pull the comfort panels to open them.

• Remove the filters one by one pushing them towards the back side of the hood unit and simultaneously pulling
downwards.

• Any kind of bending of the filters has to be avoided when washing them. Before fitting them again into the hood make
sure that they are completely dry. (The colour of the filter sur-face may change throughout the time but this has no
influence to the filter efficiency).

• When fitting the filters into the hood pay attention that they are mounted in correct position the handle facing
outwards.

Charcoal filter (recycling version)

This filter cannot be washed or regenerated. It must be replaced when the EF appears on the display or at least once
every 4 months. Activation of the alarm signal

• In the recycling version hoods the filter saturation alarm must be activated during the installation or later.

• Switch off the hood and the lights.

• Disconnect the hood from the mains supply.

• When restoring the connection press and hold B-key.

• When releasing the key two rotating rectangles appear on the display.

• Within 3 seconds press the B-key until a flashing confirmation appears on the dispaly:

• 2 flashes with EF - charcoal filter saturation alarm ACTIVATED

• 1 flash with EF - charcoal filter saturation alarm DEACTIVATED.

REPLACING THE CHARCOAL FILTER Reset of the alarm signal

• Switch off the hood and the lighting. If the 24h-function has been activated this has to be deactivated.

• Press the E-key until the display is unlit. Replacing of the filter

• Open the comfort panels pulling them downwards.

• Remove the metal grease filters.

• Remove the saturated charcoal filter by releasing the fixing hooks

• Fit the new filter and fasten it in its correct position.