Franke TA7001 User Manual

Australian Approvals

• This mixer complies to Australian and New Zealand Standards AS/NZS 6400.

• The mixer has 4 Star water ef ficiency rating under the WELS Scheme with water

consumption of 7.5 liters per minute.

FRANKE ARTIS

15 YEAR WARRANTY

Fifteen (15) year warranty applies to replacement ceramic cartridge, ve (5) years parts and labour starting from date of purchase of

•
product. After ve (5) years, a further additional ten (10) years replacement ceramic cartridge warranty is applicable. This extended part-only
warranty is non-transferable and applies only to the original purchaser. The guarantee only applies if the mixer is installed with pressure
limiting valves.
Any faults caused by defective production will be replaced free-of-charge during the guarantee period.

•
Any such faults will be replaced, at the sole discretion of Franke, either by repairing faulty components or by replacing the whole product

•
with the same or an equivalent model where the balance of the warranty period from the original date of purchase will take eect. The
Company is not liable for damage caused by: a) improper or unsuitable use and/or maintenance - b) transport - c) knocks, tampering,
incorrect repairs and repairs made by unauthorised technicians - d) normal wear of components (non-return valve, membrane, etc.) and/or
the use of non-original spare parts - e) non-compliance with the technical instructions - f) freezing and/or impurities in the water pipes.
The guarantee only applies if a document proving the date of purchase is produced.

•
The guarantee covers all the countries where Franke products are sold, either directly or through an authorised distributor.

•
The guarantee does not cover product assembly or disassembly charges, visits and calls of specialised technicians, costs borne by the

•
customer due to the unavailability and/or non-use of the product.
Any imperfections in the nishes or in the natural materials used should not be considered as faults but a typical characteristic of these

•
crafted products.
In the case of various accessible visible components and products requiring only minor rectication under guarantee, Franke reserves the

•
right to supply these on a “parts only” basis to the customer. Such articles may include accessories, aerators, hand sprays, hoses, handles,
levers, xings, washers and dress ttings, etc.

IMPORTANT INFORMATION

Flush out pipe work prior to connecting your new mixer.

•
All mixers to be installed with isolating stop cocks.

•
Tap must be installed with pressure limiting valves.

•
Mixer should be installed by a qualied plumber.

•
This mixer is designed for domestic use only.

•
Failure to comply will void all warranty.

•

Franke has a service network in all metropolitan areas and most regional areas. Where the warranty claim has been made outside a radius of
50km from any store where the product can be purchased, the customer is responsible for the cost of delivery to the nearest service agent
or the travel cost for a technician to travel to a location outside the 50km radius, unless agreed otherwise with the company.

Should you ever need to make a warranty related enquiry about your Franke product, simply call [phone] to speak with our friendly
customer service consultants. We suggest you have the following information close at hand to make the process as easy as possible:

1. Model number of your tap

2. A copy of your original purchase receipt

3. Address details of where the tap is installed
Alternatively, you may email, fax or post a service request to the details provided below.

Any associated or ancillary costs to be incurred by you as a result of replacement or repair of Franke taps under this guarantee shall, in all
cases, be previously approved by PR Kitchen Systems Pty Ltd. Please note: The benets provided under this warranty are additional to other
rights and remedies available to the customer under the Australian Customer Law.

TA 7001 PULL-OUT

FRANKE USER INSTRUCTIONS AND
GUARANTEE FOR MIXERS

YOUR STATUTORY RIGHTS

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or a refund
for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

For further information on Franke kitchen
sinks, taps, waste management systems and
accessories visit our website or contact us for

your nearest retailer.

PR Kitchen Systems Pty Ltd

83 Bangholme Road, Dandenong South VIC 3175

Ph [phone]

Fax [phone]

www.franke.com.au

Instruction code: IISTRNP117/1PER#C08528 Rev 06/2012.

Franke care instructions.

1950319 Cromo
1950320 Satinato
1950321 Avena

• Periodically clean the aerator filter;

• Install filter valves under the sink and periodically clean the filters;

• DO NOT USE DETERGENTS, SOLVENTS, CHEMICAL AGENTS, ABRASIVE
SPONGES, WIRE WOOL OR ALCOHOL, ETC., which would irreparably damage
the surface of the product and ruin its appearance, sheen and matt finishes;

• CLEAN WITH SOAPY WATER AND DRY WITH A SOFT CLOTH;

• Dry the product after use if the water is very hard or aggressive, as it may
leave deposits which would damage the surface;

• Do not install the tap when the water pressure exceeds 500 kpa (in this case
pressure limiting valves are required);

• Rinse the water pipes before installing the tap.

1950322 Grafite
1950323 Sahara

Chrome Handle

1950396 Alluminio

1950319

1950480 Cromo
1950503 Satinato

Cartridge

1950521

1950521

Hose for Hand
shower 1950481

1950481

1950504 Avena
1950505 Grafite
1950506 Sahara

Hand Shower

1950507 Alluminio

142/133

Franke installation instructions.

Outer casing

1

Dress ring washer

2

Rubber seal

3

Under sink washer

4

Brass fixing nut

5

Flexible connector

6

Pull out hose

7

Washer

8

Weight connector

9

Counter weight

10

Locking screw

11

Hand shower

12

Technical Information

• Maximum hot temperature 80° (Recommended 65°)

• Maximum operating pressure 75 psi / 500 kpa

• Minimum operating pressure 7.25 psi / 50 kpa

• Ceramic cartridge

Flexible Hose
203/95 + 203/96

- Close the water.

- Place the washer 2 on the base of the sink 1.

- Introduce the body 1 into the sink hole.

- Introduce the washer 3 under the sink.

- Place the fixing plate 4 under the sink.

- Tighten the whole by screwing firmly the fixing nut 5 to the stem of the body 1, and keeping
the spout turned 70° to the left, corresponding to the stop.

- The tap must be placed in the central position respectively to 140° rotation.

- Connect the flexible 7 to the flexible 9 with washer 8.

- Place the load weight 10 on the flexible 9 with the screw 11.

- Connect the flexibles 6 (red hot water, blue cold water) to the water supply-pipes or to filter
taps (not included in the packaging).

- Do not install the flexibles in tightness and twisting conditions during the rotation, to permit
free rotation.

- Open the water.