Franke LAX11015 Installation manual

DROP-IN (ABOVE MOUNT): STAINLESS STEEL

NOTE: Inspect sink for damage; do not install a damaged unit. File a claim against the shipping agent.

1. Place template on the counter and trace.

2. Cut along the outline.

3. Slide or snap clips into position. Turn claws of clips towards sink. (To clear countertop while lowering sink into cutout).

NOTE: Some clips may already be in place.

4. Faucet and strainer basket may be assembled at this time, if desired.

5. Lower sink into countertop cutout. Most Franke sinks are shipped with factory applied polyseal. These need no extra sealant.
If there is no factory installed sealant, please use additional sealant.

6. Turn clips out and tighten against the underside of the countertop.

DROP-IN SLIM FIX: STAINLESS STEEL

NOTE: Inspect sink for damage; do not install a damaged unit. File a claim against the shipping agent.

1. Place template on counter and trace.

2. Cut along the outline (NOTE: it is important to cut exactly to the trace line – the sink ledge that overhangs on the countertop
is low profile [see Inset A]).

3. Strainer basket may be assembled at this time if desired.

4. Place silicone on inner edge of cut-out and a thin application along cut line atop the counter.

5. Simply place the sink into the cut-out, making certain drain hole is to the back. Clips will automatically adhere to the counter
(see Inset B & C).

6. Remove excess silicone.

NOTE: none of these installations apply to Franke Fireclay Sinks.
Please visit our website for separate Fireclay sink installation instructions.

In the USA:
www.frankeconsumerproducts.com

In Canada:
www.frankecanada.com

FSSII0509

31219

0509

Installation Instructions for Your Franke Stainless Steel Sink

Find your sink model listed on the back page for corresponding method of installation.

Inset A Inset B Inset C

226494_Franke_31219_FSSii0509_Installation_V2.qxd:226494_31219_Franke_infoBil.qxd 6/1/09 9:44 AM Page 1

UNDERMOUNT: STAINLESS STEEL: SINGLE BOWL

This sink is specifically designed to be undermounted in a solid surface countertop only.
CAUTION: Sink edge may be sharp; handle with caution. Do not install a damaged sink. Inspect carefully.

1. The size should be exact as this sink uses coordinating accessories which fit precisely in the cut out.

2. Determine placement of the clip brackets as indicated on the template. Pre-drill holes according to method desired based on
countertop material. NOTE: You the fabricator may elect to epoxy in the screw or use a brass anchor.

3. Apply a bead of silicone evenly along edge on the underside of countertop.

4. Position and align sink over the opening. Press sink into silicone seal.

5. After re-checking alignment, tighten clip brackets against the sink edge.

6. Remove excess silicone.

HINT: After silicone cures, wipe inside edge with denatured alcohol. This will smooth out any rough areas.
NOTE: The template included (or dxf file downloaded from website) is only a guide. The actual sink and accessories should ALWAYS

be present to ensure a perfect cut. FRANKE is not responsible for an improperly cut countertop or improper installation.

UNDERMOUNT: STAINLESS STEEL: MULTIPLE BOWLS

This sink is specifically designed to be undermounted in a solid surface countertop only.
CAUTION: Sink edge may be sharp; handle with caution. Do not install a damaged sink. Inspect carefully.

1. The size should be exact as this sink uses coordinating accessories which fit precisely in the cut out.

2. Determine placement of the clip brackets as indicated on the template. Pre-drill holes according to method desired based on
countertop material. NOTE: You the fabricator may elect to epoxy in the screw or use a brass anchor.

3. Apply a bead of silicone evenly along edge on the underside of countertop.

4. Position and align sink over the opening. Press sink into silicone seal.

5. After re-checking alignment, tighten clip brackets against the sink edge.

6. Remove excess silicone

HINT: After silicone cures, wipe inside edge with denatured alcohol. This will smooth out any rough areas.
NOTE: The template included (or .dxf file downloaded from website) is only a guide. The actual sink and accessories should ALWAYS

be present to ensure a perfect cut. FRANKE is not responsible for an improperly cut countertop or improper installation.

Countertop cut is top of bevel. No recessed countertop. No countertop overhang.

Sink flush with countertop. No recessed countertop. No countertop overhang.

0509 FSSII0509

31219

226494_Franke_31219_FSSii0509_Installation_V2.qxd:226494_31219_Franke_infoBil.qxd 6/1/09 9:44 AM Page 2

UNDERMOUNT: STAINLESS STEEL: MULTIPLE BOWLS

This sink is specifically designed to be undermounted in a solid surface countertop only.
CAUTION: Sink edge may be sharp; handle with caution. Do not install a damaged sink. Inspect carefully.

1. The size should be exact as this sink uses coordinating accessories which fit precisely in the cut out.

2. Determine placement of the clip brackets as indicated on the template. Pre-drill holes according to method desired based on
countertop material. NOTE: You the fabricator, may elect to epoxy in the screw or use a brass anchor.

3. Apply a bead of silicone evenly along edge on the underside of countertop.

4. Position and align sink over the opening. Press sink into silicone seal.

5. After re-checking alignment, tighten clip brackets against the sink edge.

6. Remove excess silicone.

HINT: After silicone cures, wipe inside edge with denatured alcohol. This will smooth out any rough areas.
NOTE: The template included (or .dxf file downloaded from website) is only a guide. The actual sink and accessories should ALWAYS

be present to ensure a perfect cut. FRANKE is not responsible for an improperly cut countertop or improper installation.

SINKS THAT CAN EITHER BE INSET or UNDERMOUNTED

NOTE: The sink template has been designed for both inset and undermounting. The template is standard for inset mounting.

If undermounting method is needed, simply remove the outer ring at the perforated score.
CAUTION: Damage caused by improper handling or installation is not covered by the warranty. Do not install a damaged sink.

1. Cut out countertop per cutout.

A. INSET

2A. Apply silicone to underside of the rim.
3A. Lower the sink into the countertop cutout. (Waste hole should be positioned at the rear).
4A. Tighten the clip against the underside of the counter.

B. UNDERMOUNT

2B. Cut-out should be flush with the countertop.
3B. Determine placement of clip brackets as indicated by template. Pre-drill holes according to method desired based on

countertop material. NOTE: You the fabricator may elect to epoxy in the screw or use a brass anchor (not provided).

4B. Apply a bead of silicone evenly along wedge of underside of counter.
5B. Position and align sink over opening. Press sink into silicone seal.
6B. After re-checking alignment, tighten clip bracket against sink edge.
7B. Remove excess silicone.

NOTE: The template included (or .dxf file downloaded from website) is only a guide. The actual sink and accessories should ALWAYS

be present to ensure a perfect cut. FRANKE is not responsible for an improperly cut countertop or improper installation.

Countertop cut is top of bevel. No recessed countertop. No countertop overhang.

0509 FSSII0509

31219

226494_Franke_31219_FSSii0509_Installation_V2.qxd:226494_31219_Franke_infoBil.qxd 6/1/09 9:44 AM Page 3