Franke CHILLOUT FF4900, CHILLOUT FF4980 Installation Manual
INSTALLATION MANUAL
CHILLOUT
FF4900 - FF4980
LIMITED LIFETIME WARRANTY
Franke Kitchen Systems , LLC extends the following warranty to the original
purchaser of its faucets effective
January 1, 2003.
All faucets installed in a private residence will carry a limited lifetime warranty
on all mechanical parts to be free of manufacturing defects in material and
workmanship under normal usage. All chrome finishes carry a limited lifetime
warranty; all other finishes are warranted for five (5) years form the original date
of purchase.
Marine and Outdoor Installation: This faucets is NOT warranted for Marine and
Outdoor installations.
This warranty applies only to the original owner, providing the product has been
installed in accordance with our installation instructions, used as recommended
and in a normal residential application. In the event of a warranty claim, the
owner will be required to provide proof of purchase - save sales receipt. This
warranty covers all components which make the product operational. Franke, at
its option, may repair or replace the product or components necessary to restore
the product to good working condition. Franke reserves the right to inspect the
installation prior to the actual replacement of the product or component part.
This warranty does not cover misuse or abuse, accidental damages, scuffs or
scratches, improper installation, abnormal usage, negligence or damage caused
by improper maintenance or cleaning. Normal wear of parts is excluded from the
warranty.
Damage caused by impurities or acts beyond our control are not covered. Any
product or part which has been repaired or altered in any manner outside of
Franke's factory, unless previously authorized in writing by Franke, will void
warranty. Any replacement excludes transportation and any labor re-
installation costs. This warranty does not allow recovery of incidental or
consequential damages such as loss of use, delay, property damage or other
consequential damage, and Franke accepts no liability for such damages.
The Franke warranty is limited to the above conditions and to the warranty
period specified herein and is exclusive. Franke DISCLAIMS all other warranties,
expressed or implied, including IMPLIED WARRANTIES OF MERCHANTABILITY
AND/OR FITNESS FOR A PARTICULAR PURPOSE. This warranty gives you
specific legal rights that may vary from state to state.
Further information
For any further information about our products, about the installation of them or
about the guarantee, please dial the number of the customer service:
Franke Kitchen Systems
800 Aviation Parkway
Smyrna, TN 37167, USA
Phone: 800-626-5771
Email: ks-customerservice.us@franke.com
STANDARD MAINTENANCE AND
TROUBLESHOOTING
REPLACING THE CARTRIDGE
1. Shut off the water supply to the faucet.
2. Turn on the faucet briey to relieve any pressure inside the faucet.
3. Move the faucet handle to the “ OFF” position.
4. Remove indicator cap C from the lever handle.
5. Remove the screw B using an allen key.
6. Pull the lever handle A from the faucet body .
7. Unscrew the cap D.
8. Unscrew the cartridge lock nut E.
9. Lift ceramic disk cartridge F from the body and replace it with new cartridge.
Ensure the two lugs on bottom of the cartridge sit properly in the allocated holes
at the base of the body.
10. Re-assemble faucet in reverse order.
11. Test for leakage.
GENERAL MAINTENANCE
Clean aerator periodically for any buildup.
Do not use harsh detergents, solvents, chemical agents, metallic sponges, etc.
that could harm the surface and damage the finish.
Clean only with a soft sponge and soapy water.
K
J
H
G
DEF
B
A
MM
L
C
SPARE / REPLACEMENT LIST
A+B+C Handle assembly F4901
D Cap F4902
E Lock nut F4903
F Cartridge F31
G Aerator key F31
H Aerator F31
J Pull out spray assembly F31
K Pull out hose F31
L Mounting hardware kit F31
M Supply hose F4910
C031420000 REV.0 -25/06/2015
INSTALLATION INSTRUCTIONS
1. Remove all contents from the package and check for completeness.
2. Turn off water supply.
3. Remove faucet and hardware from its protective packaging. Faucet comes
assembled.
4. Cut a mounting hole 1” 3/8 diameter (35mm) in the desired position in counter
top or sink (if one isn’t available).
5. Connect the flexible supply hoses (8) to the short supply pipes in the faucet
body(1) HAND TIGHT ONLY.
6. Ensure rubber gasket (2) is in the base of faucet.
ATTENTION: The gasket should be sitting between the countertop and faucet
base.
DO NOT use putty or other sealant at this location.
NOTES:
Solid surface installation: The countertop mounting surface needs to be flat and
free of debris otherwise the faucet may not sit properly.
For tile installations, avoid installing faucet near or on top of grout lines.
This may cause a weak joint between the faucet and the counter and could cause
leaks.
7. Install the threaded bar (6) to the base of the faucet body.
8. Install the mounting hardware to the base of the faucet body in the following
order: plastic flange (3), rubber washer (4), fixing washer (5) as illustrated.
9. Tighten the fixing nut (7) on the body (1).
10. Connect the flexible supply hoses (8) to the water supply in the house.
11. Remove the aerator using a aerator key (9), turn on the water, and flush the
faucet for any debris. Ensure everything is functioning properly and check for
leaks, then reinstall the aerator.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
9
8
TECHNICAL DATA
Flow Rate 1.75 GPM at 45 PSI
Recommended Water Pressure 30-75 PSI
Max. Water Pressure 145 PSI
Recommended Hot Water Temp. 120°-140° F
Hole Size For Faucet 1” 3/8
Certifies this faucet complies with ASME A112.18.1 / CSA B125.1 &
NSF 61, NSF 372 and AB1953.
NOTE
Contact us immediately if you see inconsistencies:
Phone – 1-800-626-5771
Email – ks-customerservice.us@franke.com
Website – www.frankeksd.com
CONTENTS IN BOX
1 - Faucet assembly
2 - Rubber gasket
3 - Plastic flange
4 - Rubber washer
5 - Fixing washer
6 - Threaded bar
7 - Fixing nut
8 - Supply hoses
9 - Aerator key
Loading...