Page 1
Operating instructions
Floor sander PYTHON C 3,2kW/50Hz
with gentle lifting lever
Item no 048666
Art. Nr. 049275
Page 2
© 2007
Reproduction on whole or in part requires written permission from
Hermann Frank GmbH & Co. KG, 75038 Oberderdingen, Germany.
All rights reserved.
No liability for any damage arising from the use of this brochure.
Subject to alterations.
Hermann Frank GmbH & Co. KG
Östliche Bahnhofstraße 8
75038 Oberderdingen
Germany
Tel.: +49 (0)72 58/60 88-0
Fax: +49 (0)72 58/60 88-11
info@hermannfrank.de
www.hermannfrank.de
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Stand: Februar 2008
Page 3
3 02/2008
This brochure uses the symbol to mark important instructions for safety and preventing damage.
Please give special attention to the marked instructions.
They refer to a potentially dangerous situation. Failure to comply can result in fatal or severe injuries and
damage to property.
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 4
4 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Contents
1 Introduction.................................................................................................................................... 6
2 Scope of delivery........................................................................................................................... 7
3 Machine specifications PYTHON C ............................................................................................. 8
3.1 Important components..................................................................................................................... 8
3.2 Technical data ................................................................................................................................. 9
3.3 Safety and machine protection facilities .......................................................................................... 9
4 Proper use...................................................................................................................................... 9
5 Installing the guide tube .............................................................................................................. 10
6 Disassembling for transport ........................................................................................................ 11
6.1 Removing the guide tube ............................................................................................................... 11
6.2 Removing the motor ........................................................................................................................ 12
7 Operating the PYTHON C ............................................................................................................ 14
7.1 Protective clothing and equipment ................................................................................................ 14
7.2 Fitting the dust bag ....................................................................................................................... 15
7.3 Safety instructions regarding dust .................................................................................................. 16
7.4 Disposing of sanding dust ............................................................................................................. 17
7.5 Replacing the sanding belt ............................................................................................................ 18
7.6 Adjusting the sanding pressure ..................................................................................................... 19
7.7 Safety instructions for electric cable and connectors .................................................................... 20
7.8 Connecting the PYTHON C to the mains power ........................................................................... 20
7.9 Remarks about sanding parquet and plank floors ......................................................................... 22
7.10 Sanding with the PYTHON C ........................................................................................................ 25
8 Maintenance .................................................................................................................................. 30
8.1 Changing the sanding drum .......................................................................................................... 30
8.2 Adjusting the running wheels ......................................................................................................... 32
8.3 Adjusting the castor wheels ........................................................................................................... 34
8.4 Adjusting the tension roller ............................................................................................................. 35
8.5 Tightening the V-belts...................................................................................................................... 36
8.6 Guarantee........................................................................................................................................ 37
Page 5
9 Parts lists
......................................................................................................................................... 37
5 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 6
1 Introduction
Dear customer,
you have decided in favour of the FRANK parquet floor sander PYTHON C, the correct choice
with respect to quality and performance.
The PYTHON C is the result of a consistent implementation of many years of experience.
This machine combines an extraordinary high sanding performance and an excellent sanding
quality, together with an easy to operate, proven and reliable technology.
This operating instructions contain important informations for the use and safe operation of the
PYTHON C.
Caution!
Read these operating instructions carefully before assembling or operating the
PYTHON C. Ensure that all operators read these operating instructions prior to operate
the machine.
Adherence to the safety notes helps to protect against potential dangers for health and
personal safety and to prevent an improper utilisation of the machine.
Before starting to work, make yourself familiar with the operation of the machine. It's too
late if you do it while working!
Never allow anybody without sufficient skills and knowledge to operate the machine.
6 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 7
7 02/2008
2 Scope of delivery
1 guide tube
2 dust bag
3 cable with plug and coupling
4 lower part of the machine with motor
5 wing screws (2 pieces)
6 operating instructions
7 hexagon socket screw key 5 mm
8 hexagon socket screw key 6 mm
9 hexagon socket screw key 10 mm
10 running wheel adjusting tool
11 tool pouch
12 fork wrench 10 mm
13 fork wrench 13 mm
14 fork wrench 24 mm
15 double fork wrench 30/36 mm
16 hearing protectors
17 respirator
18 Multiclip
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 8
3 Machine specifications PYTHON C
3.1 Important components
1 pressure regulating screw 11 bumper wheel
2 castor wheels 12 belt guard
3 running wheels 13 motor
4 drum cover 14 switch box
5 V-belt tension screw 15 dust bag
6 tension lever 16 cable arm
7 knurled nut 17 left hand grip
8 clamping lever 18 main lifting lever
9 motor plug 19 right hand grip
10 carrying handle 20 gentle lifting lever
8 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Page 9
9 02/2008
3.2 Technical data
Single-phase AC motor. . . . . . . . . . . . . . . . . . . . . . 240 V, 60 Hz
Motor power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,2kW
Sanding drum speed . . . . . . . . . . . . . . . . . . . . . . . . . . 2100 rpm
Sanding width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 mm
Sanding belt dimensions . . . . . . . . . 250 mm x 750 mm, endless
Machine weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 kg
3.3 Safety and machine protection facilities
PYTHON C is equipped with an
- overcurrent cutout and an
- no-volt release
The overcurrent cutout protects the machine from damage and persons from endangering in the
case of short circuits.
The no-volt release prevents uncontrolled restart of the machine after power failure. The motor
will not restart automatically when the power returns, it will have to be switched on again.
4 Proper use
The parquet floor sander PYTHON C is suitable for dry sanding of parquet and plank
floors. No other use is allowed.
Caution!
Never use PYTHON for wet procedures (mortal risk from electric shock)!
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 10
5 Installing the guide tube
Note: The Python C is delivered with the guide tube (1) removed.
Caution!
Injury to the operator or other persons could occur or damage could occur if the machine
starts up unintentionally. Disconnect the machine from the power supply before working
on the machine!
Instructions:
1. Insert the guide tube (1) into the guide tube support (7). The curved section of the tube must
face toward the motor. Clamp the guide tube by means of the clamping lever (6) located on
the guide tube support.
2. Fit the connector (8) into the both screws of th pull rod
3. Move the main lifting lever (2) into the rear position to raise the sanding drum from the floor.
4. Tighten both wing nuts
10 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 11
11 02/2008
6 Disassembling for transport
For easy transportation the motor and the guide tube can be removed.
6.1 Removing the guide tube
Caution!
Injury to the operator or other persons could occur or damage could occur if the machine
starts up unintentionally. Disconnect the machine from the power supply before working
on the machine!
Instructions:
1. Fold down the cable arm (3).
2. Move the main lifting lever (2) to the front position in order to lower the sanding drum to the
floor. This removes the load from the control rod (5).
3. Loosen both of the wing screws a little (4). Push the handle down to detach the control rod
(5) from the connector (8).
4. Open the guide tube support (7) with the clamping lever (6) and pull the guide tube (1) out.
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 12
6.2 Removing the motor
Caution!
Injury to the operator or other persons could occur or damage could occur if the machine
starts up unintentionally. Disconnect the machine from the power supply before working
on the machine!
Instructions:
1. Make sure that the motor switch is in the off position and that the mains cable is
disconnected from the motor plug.
2. Unscrew the knurled nut from the belt guard and open the belt guard.
3. Loosen the lock nut (2) on the belt tension screw.
4. Turn the belt tension screw (1) counterclockwise. This will lower the motor and release the
tension on the belts.
5. Remove the belts.
12 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 13
6. Remove the knurled nut from the motor bracket.
7. Now you can remove the motor.
13 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 14
14 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
7 Operating the PYTHON C
7.1 Protective clothing and equipment
Caution! Wear hearing protectors!
The supplied hearing protectors must be worn when using the machine.
The following sound level values have been measured for the parquet floor sander
PYTHON C according to DIN 45 645:
Idle mode LEQ = 85 dB(A)
Working mode LEQ = 87 dB(A)
The noise produced when the machine is working depends on various factors. Local
conditions such as room size and quality of the floor affect noise development.
Caution! Wear a respirator!
When using the parquet floor sander PYTHON C and when disposing of the sanding
dust, always wear a respirator (see chapter 7.3 and 7.4). Wear the respirator which is
supplied with the accessories.
Caution! Wear safety goggles!
When using the parquet floor sander PYTHON C and when working on PYTHON C,
always wear safety goggles to protect your eyes.
Caution! Wear proper working clothing!
When using the parquet floor sander PYTHON C and when working on PYTHON C,
never wear loose clothing. This can get caught up in moving parts.
Page 15
7.2 Fitting the dust bag
Caution!
Only use original FRANK dust bags for the parquet floor sander COBRA.
Caution!
The dust bag must be firmly fitted to the dust pipe before sanding.
Instructions:
1. Pull the dust bag over the dust pipe to behind the pipe reinforcement.
2. Fasten the dust bag here using the Multiclip.
15 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 16
16 02/2008
7.3 Safety instructions regarding dust
Caution! Ultra-fine sanding dust!
Always wear a respirator when sanding parquet and plank floors (is included with the
accessories).
When the machine is used for its proper purpose, the sanding of wooden floors naturally
produces dust. The machine has an integrated dust collecting system which blows the dust into
the dust bag. The dust is collected in the dust bag. Even so, this cannot prevent fine and
ultra-fine dust being produced when using the machine.
Caution! Health risk!
Wood dust, particularly when treated with impregnating agents, solvents and coatings,
can cause allergic reactions (e.g. of the skin or respiratory system) after a sensitization
period. Beech and oak dust is classified as being carcinogenic (cancer of the nasal
mucous membranes). Dust from other kinds of wood is suspected of having a
carcinogenic effect.
Caution! Fire risk!
No smoking while sanding!
All ignition sources are prohibited in rooms where sanding work is being carried out!
Air the rooms thoroughly.
Together with an ignition source and the oxygen in the air, wood dust can cause fires and
explosions.
Caution! Fire risk!
Sanding over metal parts such as nails can produce sparks which are blown into the
dust bag together with the wood dust. Here the glowing metal chips can still cause a fire
even hours later.
Every time after the machine has stopped and at the end of working, the sanding dust
contained in the dust bag must always be disposed of immediately in a fire-proof,
non-flammable container. The container must be covered with a fire-proof,
non-flammable lid. Store the container only outdoors.
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 17
17 02/2008
7.4 Disposing of sanding dust
Caution! Fire risk!
Because of the fire risk, the sanding dust contained in the dust bag must always be
disposed of immediately every time after the machine has stopped and at the end of
working. The sanding dust must be disposed of immediately in a fire-proof,
non-flammable container. The container must be covered with a fire-proof,
non-flammable lid. Store the container only outdoors.
Caution!
At the latest when 1/3 full, the sanding dust contained in the dust bag must be disposed
of, because the dust collecting capacity is reduced when the bag is any fuller. The
sanding dust must be disposed of in a fire-proof, non-flammable container. The container
must be covered with a fire-proof, non-flammable lid. Store the container only outdoors.
Caution!
Always wear a respirator when disposing of the sanding dust (included with the
accessories).
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 18
18 02/2008
7.5 Replacing the sanding belt
Caution! Danger from machine starting up!
When replacing the sanding belt, there is a risk from the machine starting up
unintentionally. Always disconnect the parquet floor sander from the mains power before
working at the sanding belt.
Caution! Risk of cutting your hands!
The sanding grains of the sanding belt have sharp edges. Always wear safety gloves
when replacing the sanding belt.
Instructions for replacing the sanding belt:
1. Switch the machine off.
2. Disconnect the machine from the mains
power.
3. Open the sanding drum cover (1).
4. Move the tension lever (2) forward. The
sanding belt which was held under tension
is now released. Pull it out to the side.
5. Insert a new sanding belt.
6. Clamp the new sanding belt by moving the
tension lever (2) backward.
7. Close the sanding drum cover (1).
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 19
7.6 Adjusting the sanding pressure
Use the pressure regulating screw to adjust the required sanding pressure.
High sanding pressure:
Turn the pressure regulating screw inwards as far as it will go.
Low sanding pressure:
Turn the pressure regulating screw outwards to the lower marking (2) on the screw thread.
19 02/2008
1
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 20
20 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
7.7 Safety instructions for electric cable and connectors
Caution! Mortal risk from electric shock!
There is a mortal risk from electric shock if the machine is used when the electric cable
or connectors are damaged. If the electric cable and connectors are damaged, they must
be replaced by a qualified electrician.
Caution! Mortal risk from electric shock!
Running over the electric cable with the sander entails a mortal risk from electric shock!
Never point the machine towards the cable!
2
3
1
4
Page 21
7.8 Connecting the PYTHON C to the mains power
Instructions for connecting to mains power:
1. Make sure that the switch (1) is in the off position. The machine must be switched off before
connecting up to the mains power.
2. The main lifting lever for the sanding drum (2) must be moved backward so that the sanding
drum is raised from the floor.
3. Hang the swivelling cable arm (3) into the left or right cable arm bracket as required.
Wind the mains cable through the curl at the end of the cable arm (3) to keep the cable
away from the sanding zone.
4. Connect the coupling (4) of the mains cable to the motor plug, which must be
disconnected from mains power.
5. Connect the plug of the mains cable via a portable RCD (Residual Current Protective
Device) to an adequately fused and earthed 230 V mains socket.
Caution!
Never switch the motor on if the sanding belt is not tightened.
Caution!
Never switch the motor on if the sanding drum is not raised from the floor.
Caution!
Risk of injuries from the machine starting up unintentionally! Disconnect the machine from
the power supply when not in use, when changing the sanding belt and when carrying out
any other work to the machine.
21 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 22
22 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
7.9 Remarks about sanding parquet and plank floors
Caution!
Check the floor to see if any boards are loose. These must be fastened before
sanding.
Caution! Fire risk!
If there are nails in the floor, they must be countersunk so low every time before
sanding that there is no risk of hitting a nail while sanding.
Hitting a nail while sanding can produce sparks and can cause a fire. For
example a spark can create a fire in the dust bag.
Floors are sanded in sanding paths which are arranged overlappingly from left to right.
Page 23
Each sanding path corresponds to one forward and one backward movement. The backward
movement covers the same path as the precede forward movement.
23 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 24
24 02/2008
Because of the space needed for the person operating the machine and the machine itself, the
floor is not sanded over an area of approximately 1.5 m to the wall behind the sander.
Turn the machine 180° and sand the remaining area of the floor also in sanding paths which are
arranged overlappingly from left to right. Make sure that the two areas are blended together
without leaving any marks.
Note!
In most cases, the floor is sanded in several procedures. The whole floor area is sanded down
in every sanding procedure.
Informations about the proper abrasive grits, sanding pressures and sanding directions for the
several sanding procedures you will find in the brochure:
Sanding parquet and plank floors
with the FRANK parquet floor sander COBRA
and the FRANK edge sander GECKO S
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 25
25 02/2008
7.10 Sanding with COBRA
1. Before starting the machine, the main lifting lever for the sanding drum (1) must be in the
rear position. The sanding drum is clearly raised from the floor. The distance to the floor is
approx. 15 mm.
2. Before starting the machine, ensure that the sanding belt is tightened.
3. Bring the machine into the start position.
4. Set the switch to setting "I". Once the motor has started up, switch to setting "II". This
gradual start-up procedure avoids high start-up currents.
1
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 26
26 02/2008
5. Before you lower the sanding drum to approx. 5 mm above the floor, you must pull the
gentle lifting lever (2) up by bending the fingers of your right hand and hold in this position.
6. With your left hand, turn the left handle (3) to unlock the stop of the main lifting lever (1).
While doing so, hold the gentle lifting lever (2) up with your right hand,
7. While you hold the gentle lifting lever (2) up, push the main lifting lever (1) forward. This
lowers the sanding drum to approx. 5 mm over the floor. The gentle lifting lever (2) must
always be held up because otherwise the sanding drum will be lowered to the floor.
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
2
1
3
Page 27
27 02/2008
8. Now start on sanding the first path by slowly lowering the gentle lifting lever (2) while you are
moving the machine forward evenly, thus lowering the sanding drum to the floor.
Caution!
Move the machine at an even pace while sanding to avoid creating any dents in the floor.
2
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 28
28 02/2008
9. At the end of the forward movement, before the movement has finished, raise the sanding
drum from the floor again by pulling the gentle lifting lever (2).
10. Every forward movement is followed by a backward movement. The backward movement
covers the same path as the forward movement. For each forward movement, move the
machine about 10 cm to the right of the sanding path you have just finished.
Caution!
Never allow the machine to come to a standstill for even a short moment while sanding
because this would cause an indentation in the floor. This means that whenever
changing between a forward and a backward movement, the sanding drum must be
raised from the floor while the machine is still moving evenly, and only lowered when the
machine is moving evenly again.
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
2
Page 29
29 02/2008
11. Stopping or interrupting the sanding procedure:
To stop or interrupt the sanding procedure, you must hold the gentle lifting lever (2) up with
your right hand for as long as it takes for your left hand to move the main lifting lever (1) into
the rear position. Do not release the gentle lifting lever (2) until this has been completed.
Then switch the motor off and disconnect from the mains power.
Safeguard the machine to prevent it rolling away.
The sanding dust contained in the dust bag must be disposed of immediately in a
fire-proof, non-flammable container. The container must be covered with a fire-proof,
non-flammable lid. Store the container only outdoors.
1
2
3
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 30
30 02/2008
8 Maintenance
8.1 Changing the sanding drum
If the sanding drum is damaged or worn, it must be replaced.
Instructions:
1. Turn the machine off.
2. Disconnect the machine from the mains power.
3. Open the sanding drum cover (1).
4. Fold the tension lever (2) forward to relieve the tension on the sanding belt.
5. Remove the sanding belt (3) to the side.
6. Unscrew the retaining nut (4):
The retaining nut is glued to the threads of the sanding drum shaft to ensure that it will not
fall off while the COBRA is in operation. To unscrew the retaining nut, use the double fork
wrench that comes with the machine. Lower the sanding drum so it has contact with the floor
to prevent it from turning while you are unscrewing the retaining nut.
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 31
31 02/2008
7. Lay the machine on its left side.
8. Press against the sanding drum carefully with a flat iron bar.
9. Remove the sanding drum out of the machine.
10. Be careful no to loose the parallel key.
11. Slide a new sanding drum on to the sanding drum shaft. The parallel key must fit properly in
the slot on the sanding drum shaft.
12. Apply metal adhesive to the retaining nut and screw it back on the sanding drum shaft. Stand
the machine up and lower the sanding drum to the floor to ensure that the sanding drum
does not turn while you tighten the retaining nut in the next step. Tighten the retaining nut
securely with the enclosed double fork wrench.
13. Pull the main lifting lever back to lift the sanding drum off the floor.
14. Close the sanding drum cover.
15. Ensure that the machine cannot roll away.
Note!
After changing the sanding drum, the surface setting on the machine must be newly adjusted.
(See chapter 8.2)
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 32
32 02/2008
8.2 Adjusting the running wheels
If the machine only sands on one side, the surface setting must be adjusted. Following
replacement of the sanding drum or running wheels, the surface setting must always be newly
adjusted. To make a level, uniform setting, the sanding drum and the running wheels must rest
on the same plane. The right running wheel is adjustable. The left wheel does not adjust.
Instructions:
1. Turn the machine off.
2. Disconnect the machine from the mains power.
3. Lay the machine on its left side.
4. With the running wheel adjustment device determine the position of the left running wheel.
5. Loosen the cam fixation screw on the running wheel bracket next to the right running wheel.
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 33
33 02/2008
6. Adjust the right running wheel to the position of the left running wheel using the running
wheel adjustment device. To accomplish this, turn the axle of the right running wheel with the
hexagon socket screw key until the right running wheel slightly touches the tongue of the
running wheel adjustment device.
7. Tighten the cam fixation screw on the running wheel bracket next to the right running
wheel securely.
8.3 Adjusting the castor wheels
Instructions for adjusting the castor wheels:
1. Turn the machine off.
2. Disconnect the machine from the
mains power.
3. Loosen the lock nut (1).
4. Turn the castoring shaft with the
hexagon socket screw key until
both of the castor wheels
bear weight.
5. Tighten the lock nut.
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 34
8.4 Adjusting the tension roller
The tension roller keeps automatically the track of the sanding belt concentrically to the sanding
drum. If with time the sanding belt fails to run concentrically to the sanding drum, the tension
roller must be newly adjusted.
Caution! Danger of injury!
Adjustments of the sanding belt while the machine is running and the sanding drum cover
is open may only be performed by qualified personnel (in accordance with VBG 1,
§ 41 adjustment).
Caution!
Wear safety goggles and avoid loose clothing before making these adjustments.
Instructions:
Caution!
Before beginning with the following procedure, the main lifting lever must be pulled
backwards to remove the sanding drum from the floor.
1. Make sure that the motor is in the off position and the machine is disconnected from the
mains power.
2. Open the sanding drum cover.
3. Insert a sanding belt.
4. Shift the tension lever backwards to place tension on the sanding belt.
5. Loosen the retaining nut (1).
6. Connect the machine to the mains power (see chapter 7.7 and chapter 7.8).
7. Allow the machine to run in position "I".
8. By turning the adjusting nuts (2), you can move the tension roller to influence the path of the
sanding belt. Adjust the position of the sanding belt until it runs in the middle of the sanding drum.
9. Switch the machine off.
10. Disconnect the machine from the mains power.
11. Tighten the adjusting nuts (2).
12. Tighten the retaining nut (1) securely.
13. Close the sanding drum cover.
34 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 35
35 02/2008
8.5 Tightening the V-belts
If the V-belt tension has eased, adjustment must be made to achieve the proper tension.
Whining or screeching are indications of insufficient V-belt tension.
Instructions for tightening slack V-belts:
1. Switch the machine off.
2. Disconnect the machine from the mains power.
3. Unscrew the knurled nut on the belt guard and open the belt guard.
4. Loosen the lock nut (2) on the belt tension screw.
5. Turn the belt tension screw (1) clockwise until the V-belts are tight.
6. Tighten the lock nut (2).
7. Close the belt guard and screw the knurled nut back securely in place to secure the belt
guard.
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 36
36 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
8.6 Guarantee
The guarantee period for new Frank machines is one year from the time of delivery/transfer to the customer,
unless another period applies pursuant to mandatory legal regulations.
When making a claim under guarantee, the invoice and/or proof of purchase must be provided.
All repairs covered by the guarantee must be carried out by a Frank service shop recognised by us. Repairs
which are carried out by the customer and/or improperly automatically lead to a disentitlement from guarantee
claims. The same is true of improper operation and/or use.
Replacement of parts, accessories and other changes to Frank machines
Frank machines provide users with a high degree of safety and reliabiity. To maintain this, the condition of your
Frank machine may not be changed from that on the date it was delivered from the factory without observing
the following rules. These rules apply for the replacement of parts, the addition of accessories and other
technical changes.
r All work done on your Frank machine must be carried out exclusively by a specialist workshop which
has suitably trained and experienced staff and the working materials required. For this, we recommend
an authorised Frank service shop.
r In the event that parts are deliberately replaced, accessories are deliberately added or other technical
changes are deliberately carried out, the customer must always consult an authorised Frank service
shop or us, the manufacturer, before starting the work.
r We urgently recommend only using safety-checked original Frank spare parts and original Frank
accessories which have been cleared by us, the manufacturer. These spare parts and accessories can
be purchased from your authorised Frank service shop, which will also be pleased to assemble them
for you properly.
Original Frank spare parts and Frank accessories have been specially tested for their safety and
suitability for Frank machines.
We can not sufficiently judge the safety and suitability of spare parts and accessories which are
not original Frank parts, and are thus unable to vouch for them.
r To maintain operating reliability and avoid damage, in the case of technical changes – of whatever kind
– our technical guidelines are to be observed in every case. Please also contact us at any other
time if you have any questions about your Frank machine.
FRANK can not assume any liability for damages caused as a result of improper work and/or violation of the
above terms and conditions.
Page 37
37 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
9.
5.
4.
3.
7.
8.
2.
Spare Parts
Floor sander Python C 3,2kW/50Hz
Item no 048666
6. Carriage
4. Tension roller
2. Sanding drum bearing
7. Steering-wheel
10. Switch housing
8. Handle
5. Roller clamp
3. Ventilator
9. Motor
1. Housing
Page 38
38 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
3.02
12.00
1.00
14.15
9.01
10.00
6.01
6.00
12.01
8.07
8.07
11.01
11.00
62.00
7.03
7.00
7.01
62.01
4.00
66.00
1.02
1.01
7.02
98.00
98.01
9.00
9.01
8.06
8.07
9.00
9.01
73.00
73.02
73.03
73.01
73.04
6.02
6.01
8.03
4.00
4.01
1. Maschinengehäuse: COBRA 3,68kW/60Hz1. Housing: Python C 3,2kW/50Hz
Item no 048666
Page 39
39 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Pos Pcs Ref Description Bezeichnung Norm
1.00 1 043854 Machine chassis Maschinengehäuse
1.01 2 014731 Cylinder screw Zylinderkopfschraube DIN 912 - M6 x 25
1.02 1 048585 Handle Griff
3.02 1 016321 Serrated lock washer Fächerscheibe DIN 6798 - A 8,4
4.00 1 016327 Regulating screw Druck-Regulier-Schraube
4.01 1 043852 O-Ring red Markierungsring rot Ø 18 x 2,65
6.00 1 016328 Cover lock Deckelschloss
6.01 4 018323 Counter sunk screw Senkschraube DIN 963 - M4 x 8
6.02 1 016384 Lock notch Schloss Raste
7.00 1 016330 Stud bolt Stiftschraube DIN 835 - M8 x 85
7.01 1 014810 Hexagon nut Sechskantmutter DIN 934 - M8
7.02 1 016331 Knurled nut tall Rändelmutter DIN 466 - M8
7.03 1 018655 Knurled nut small Rändelmutter DIN 467 - M8
8.03 1 016176 Drum guard cover Walzenschutz
8.06 1 014729 Cylinder screw Zylinderkopfschraube DIN 912 - M6 x 16
8.07 3 014809 Hexagon nut Sechskantmutter DIN 934 - M6
9.00 2 016332 Cover hinges Scharnier
9.01 4 018666 Hexagon nut Sechskantmuttern, dünn ISO 4035 - M6
10.00 2 016334 Hood hinges Scharnierbolzen
11.00 1 016177 Bumper wheel Anlaufrad
11.01 1 018264 Cylinder screw Zylinderkopfschraube DIN 912 - M6 x 35
12.00 1 016336 Bumper wheel support Langloch-Winkeleisen
12.01 1 047212 Clamp lever adjustable Klemmhebel verstellbar GN300-45-M6x16
14.15 1 014736 Cylinder screw Zylinderkopfschraube DIN 912 - M8 x 30
62.00 1 043829 Main axle Fahrwerkachse
62.01 2 043891 Outer packing ring Sicherungsringe für Wellen DIN 471 - 16x1
66.00 1 016432 Cylinder screw Zylinderschraube DIN 912-M8x130
73.00 1 043899 Carry handle Tragebügel
73.01 1 043846 Handle covering Kunststoffbezug
73.02 1 016441 Cylinder screw Zylinderkopfschraube DIN 912 - M10 x 75
73.03 1 016442 Plastic closing Verschlussstopfen
73.04 1 019118 Plastic closing Vierkantstopfen
98.00 1 016456 Belt guard Riemenschutzhaube
98.01 1 016457 Cylinder screw Zylinderschraube DIN 912 - M6 x 85
1. Maschinengehäuse: COBRA 3,68kW/60Hz
1. Housing: Python C 3,2kW/50Hz
Item no 048666
Page 40
40 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
26.01
26.02
26.00
21.00
15.12
25.00
25.01
25.03
25.01
15.12
22.00
27.00
26.01
23.00
18.00
17.00
13.00
25.02
16.01
16.02
17.00
16.00
Pos Pcs Ref Description Bezeichnung Norm
13.00 1 043879 Drum COBRA Schleifwalze gummiert COBRA KING COBRA 10” (250mm)
15.12 2 014857 Lock ring Sicherungsringe für Bohrungen DIN 472 - 52x2
16.00 1 043880 Drum shaft COBRA Schleifwalzenwelle COBRA KING COBRA 10” (250mm)
16.01 1 016361 Parallel key Paßfeder DIN 6885 - A 6 x 6 x 30
16.02 1 016362 Parallel key Paßfeder DIN 6885 - A 6 x 6 x 20
17.00 2 014614 Hexagon nut Sechskantmuttern, dünn ISO 4035 - M24x1,5
18.00 1 018348 Ball bearings Rillenkugellager DIN 625 T1 - 6205 - 25 x 52 x 15
21.00 1 016183 Needle bearing Nadellager mit Führungflanschen DIN 617 SKF - SKF NA 49/32
22.00 1 016184 Spacer Distanzbuchse
23.00 1 016185 Drum pulley Walzen-Riemenscheibe
25.00 1 016364 Drum bearing flange Walzenlagerflansch
25.01 4 016365 Cylinder screw Zylinderkopfschraube DIN 6912 - M8 x 25
25.02 1 048046 Drum flange complete Walzenlagerflansch komplett PYTHON C
26.00 1 016366 Inner drum cover Lagerdeckel innen
26.01 6 016701 Counter sunk screw Senkschraube DIN 963 - M5 x 16
26.02 1 016188 Felt packing strip Filzdichtring
27.00 1 016368 Outer drum cover Lagerdeckel aussen
98.03 1 016458 V-belt guard Schutzblech
5. Schleifwalzenlager: COBRA 3,68kW/60Hz2. Sanding drum bearing: Python C 3,2kW/50Hz
Item no 048666
Page 41
36.01
36.00
35.00
34.00
28.00
15.14
35.00
15.14
31.00
33.00
15.06
36.02
74.03
74.04
60.05
74.06
74.03
74.02
74.01
74.00
74.02
74.05
74.0874.07
3. Ventilator: Python C 3,2kW/50Hz
Item no 048666
Pos Pcs Ref Description Bezeichnung Norm
15.06 3 014726 Cylinder screw Zylinderkopfschraube DIN 912 - M6 x 12
15.14 2 018091 Locking ring Sicherungsringe für Bohrungen DIN 472 - 35x1,5
28.00 1 016369 Fan flange Ventilatorflansch
31.00 1 016372 Spacer Distanzring 25x17x8
33.00 1 014597 Fan Shaft Ventilatorwelle
34.00 1 016374 Spacer Distanzbuchse
35.00 2 018359 Ball bearings Rillenkugellager DIN 625 T1 - 6003 - 17 x 35 x 10
36.00 1 043907 Fan Ventilatorrad
36.01 1 014830 Washer Scheibe DIN 125-1 - B 13
36.02 1 018663 Hexagon nut Sechskantmutter DIN 934 - M12
60.05 1 016424 Circlip Federring DIN 127 - A 12
74.00 1 016443 Tension ring Spannrollenring
74.01 1 018352 Ball bearings Rillenkugellager DIN 625 T1 - 6201 - 12 x 32 x 10
74.02 2 014854 Outer packing ring Sicherungsring DIN 472 - 32 x 1,2
74.03 2 016446 Spacer Distanzbuchse
74.04 1 016447 v-belt tens holder Spannrollenhalter
74.05 1 016448 Cylinder screw Zylinderkopfschraube DIN 6912 - M12 x 30
74.06 1 016449 Cylinder screw Zylinderkopfschraube DIN 6912 - M12 x 35
74.07 1 048691 Tensioner complete Spannrolle komplett
74.08 1 048033 Ventilatorflange complete Ventilatorflansch komplett PYTHON C
41 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 42
42 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
15.12
15.00
15.12
15.20
15.08
15.15 15.13
15.08
15.15
15.07
15.21
15.14
15.05
15.16
15.06
15.17
15.04
15.14
15.05
15.18
15.2 2\
U m lenkrolle\
kom p l.
15.19
15.09
15.10
15.11
Pos Pcs art. no Description Bezeichnung Werkstoff/Norm
15.00 1 043904 Tension roller shaft COBRA Umlenkrollen-Welle COBRA 10” (250 mm)
15.04 1 014622 External roller Aussenrolle
15.05 2 018351 Ball bearing Rillenkugellager DIN 625 15 x 35 x 11
15.06 1 014726 Cylinder screw Zylinderkopfschraube DIN 912 - M6 x 12
15.07 1 014625 Inner roll empty Innenrolle 014625
15.08 2 014704 Ball bearings Rillenkugellager DIN 625 25 x 47 x 12
15.09 1 016198 Swivel bearing Pendelkugellager DIN 630 - 2205 - 25 x 52 x 18
15.10 1 014628 Shaft sealing ring Wellendichtring DIN 3760 35 x 52 x 7 NBR
15.11 1 043848 Roller Laufrolle 10” (250 mm)
15.12 2 014857 Lock ring Sicherungsring DIN 472 - 52x2
15.13 1 016202 Adjustment ring Justierring
15.14 2 018091 Locking ring Sicherungsring DIN 472 - 35x1,5
15.15 2 014855 Locking ring Sicherungsring DIN 472 - 47x1,75
15.16 1 017724 Washer Scheibe DIN 9021 - 6,4
15.17 1 014634 Shaft sealing ring Wellendichtring DIN 3760 25 x 52 x 7
15.18 1 014852 Locking ring Sicherungsringe für Wellen DIN 471 - 25x1,2
15.19 1 016360 Compens. washer Stützscheibe DIN 988 - S25 x 35
15.20 1 043833 Lock washer Gewellte Federscheibe DIN 137 - B27
15.21 1 043894 Looking ring Sicherungsringe für Wellen DIN 471 - A60
15.22 1 048081 Tension roller complete Umlenkrolle komplett 10” (250 mm)
7. Umlenkrolle:
COBRA 3,68kW/60Hz
4. Tension roller:
Python C 3,2kW/50Hz
Item no 048666
Page 43
43 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
7.01
14.05
14.06
14.01
14.02
14.11
7.01
15.02
7.01
14.00
15.01
14.07
14.14
7.01
14.04
14.09
14.10
14.03
14.15
8. Walzenspanner: COBRA 3,68kW/60Hz
Pos Pcs Ref Description Bezeichnung Werkstoff/Norm
7.01 4 014810 Hexagon nut Sechskantmutter DIN 934 - M8
14.00 1 016338 Tension lever Spannwalzenhalter
14.01 1 016179 Pressure spring Druckfeder
14.02 1 016492 Pressure pad Druckstück
14.03 1 016340 Cylinder screw Zylinderkopfschraube DIN 6912 - M10
14.04 1 014811 Hexagon nut Sechskantmutter DIN 934 - M10
14.05 1 016342 Tension lever Spannhebel
14.06 1 016180 Handle grip Ballengriff
14.07 1 016343 Cylinder screw Zylinderkopfschraube DIN 6912 - M8 x 45
14.09 1 016345 Mounting bolt Haltebolzen
14.10 1 017116 Countersink screw Senkschraube DIN 963 - M8 x 30
14.11 1 016347 Eye screw Ringschraube DIN 444 - A - M8 x 80
14.14 1 043902 Washer Unterlegscheiben DIN 522 - 8,4 x 30
14.15 1 048500 Trnsion lever compl. Spannwalzenhalter komplett
15.01 1 016190 Adjusting plate Führungsplatte
15.02 1 014620 Hexagon nut Sechskantmutter DIN 934 - M16
5. Roller clamp: Python C 3,2kW/50Hz
Item no 048666
Page 44
44 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
60.01
26.01
58.03
15.05
15.05
60.00
58.02
58.00
65.01
3.07
7.01
3.02
67.00
3.07
68.01
3.07
68.00
8.07
14.01
63.00
61.00
60.05
60.01
57.04
66.01
65.00
7.01
14.15
6. Carriage: Python C 3,2kW/50Hz
Item no 048666
Pos Pcs Ref Description Bezeichnung Werkstoff/Norm
3.02 1 016321 Serrated lock washer Fächerscheibe DIN 6798 - A 8,4
3.07 3 014828 Washer Scheibe DIN 125-1 - B 8,4
7.01 2 014810 Hexagon nut Sechskantmutter DIN 934 - M8
8.07 1 014809 Hexagon nut Sechskantmutter DIN 934 - M6
14.01 1 016179 Pressure spring Druckfeder
14.15 1 014735 Cylinder screw Zylinderkopfschraube DIN 912 - M8 x 25
15.05 4 018351 ball bearing Rillenkugellager DIN 625 15 x 35 x 11
26.01 6 016701 Counter sunk screw Senkschraube DIN 963 - M5 x 16
57.04 2 018101 Outer packing ring Sicherungsringe für Wellen DIN 471 - 15x1
58.00 2 016415 Caster wheel felloe Lauf- u. Lenkradfelge
58.02 2 016171 Vulkollan-shoe Vulkolanbelag
58.03 2 016416 felloe cover Felgendeckel
59.06 1 037082 Running wheel complete Laufrad komplett
60.00 1 016422 Running wheel bushing Laufradbuchse
60.01 2 016554 Cylinder screw Zylinderkopfschraube DIN 6912 - M12 x 55
60.05 1 016424 Circlip Federring DIN 127 - A 12
61.00 1 016425 Excentric Exzenter
63.00 1 043828 Running wheel bracket Fahrwerkhebel
65.00 1 016175 Reg. Spring Zugfeder
65.01 1 016430 Cylinder screw Zylinderkopfschraube DIN 6912 - M8 x 35
66.01 1 014816 Hexagon nut Sechskantmutter DIN 985 - M8
67.00 1 043914 Control rod connector Zugstangen-Verbindung
68.00 1 016739 Cylinder screw Zylinderkopfschraube DIN 912 - M8 x 45
68.01 1 016437 Spacer Distanzbuchse 68.01 11x8x5
Page 45
3. Lenkrolle: COBRA
3.02
51.00
15.05
57.04
57.03
15.05
15.05
3.02
55.01
35.00
15.14
58.03
26.01
57.03
58.02
58.00
57.00
55.00
56.00
56.01
15.14
58.52
58.51
58.53
Pos Pcs Ref Description Bezeichnung Norm
3.02 2 016321 Serrated lock washer Fächerscheibe DIN 6798 - A 8,4
15.05 3 018351 Ball bearing Rillenkugellager DIN 625 T1 - 6202 - 15 x 35 x 11
15.14 2 018091 Locking ring Sicherungsringe für Bohrungen DIN 472 - 35x1,5
26.01 3 016701 Counter sunk screw Senkschraube DIN 963 - M5 x 16
35.00 1 018359 Ball bearings Rillenkugellager DIN 625 T1 - 6003 - 17 x 35 x 10
51.00 1 016406 Steering-wheel fork Lenkrollengabel
55.00 1 016410 Bushing axle Schwenkachse
55.01 1 014850 Outer packing ring Sicherungsringe für Wellen DIN 471 - 17x1
56.00 1 039981 Hexagon nut Sechskantmutter DIN 934 - M20
56.01 1 039982 Washer Scheibe DIN 125-1 - B 21
57.00 1 014601 Caster wheel axle Lenkrad-Achse
57.03 2 016413 Cylinder screw Zylinderkopfschraube DIN 6912 - M8 x 20
57.04 1 018101 Outer packing ring Sicherungsringe für Wellen DIN 471 - 15x1
58.00 1 016415 Caster wheel fell. Lauf- u. Lenkradfelge
58.02 1 016171 Vulkollan-shoe Vulkolanbelag
58.03 1 016416 Felloe cover Felgendeckel
58.51 1 047064 Steering-wheel fork compl. Lenkradgabel komplett
58.52 1 016380 Wheel compl. Rolle komplett
58.53 1 016380 Steering wheel compl. Lenkrolle komplett
7. Steering-wheel:
Python C 3,2kW/50Hz
Item no 048666
45 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Page 46
46 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
49.01
37.02
37.03
37.00
39.00
44.00
46.11
46.06
46.06
14.06
46.10
46.00
46.04
46.03
42.00
43.04
43.01
43.00
47.01
46.10
14.06
38.04
38.06
37.04
37.01
50.01
15.16
15.16
43.05
47.00
38.00
47.01
44.06
8.07
15.16
43.02
15.16
44.01
44.07
44.08
8.07
3.00
40.00
14.15
39.03
3.06
3.07
3.03
3.01
3.02
39.04
3.02
46.03
67.01
42.01
49.00
49.00
39.01
3.07
3.08
3.09
38.02
38.01
39.40
41.00
9. Stiel komplett: COBRA 3,68kW/60Hz
8. Handle: Python C 3,2kW/50Hz
Item no 048666
Page 47
9. Stiel komplett: COBRA 3,68kW/60Hz8. Handle: Python C 3,2kW/50Hz
Item no 048666
47 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Pos Pcs Ref Description Bezeichnung Norm
3.00 1 047307 Dust pipe support Staub-/Lenkrohrhalter
3.01 4 014735 Cylinder screw Zylinderkopfschraube DIN 912 - M8 x 25
3.02 5 016321 Serrated lock washer Fächerscheibe DIN 6798 - A 8,4
3.03 1 047213 Hexagon screw Sechskantschraube DIN 933 - M8 x 60
3.06 1 047121 Clamping lever Klemmhebel verstellbar M8
3.07 2 014828 Washer Scheibe DIN 125-1 - B 8,4
3.08 1 048625 Steering compl. Lenkung kompl. (595)
3.09 1 048702 Dust pipe support compl. Lenkerfuß kompl.
8.07 2 014809 Hexagon nut Sechskantmutter DIN 934 - M6
14.06 2 016180 Handle grip Ballengriff
14.15 1 014736 Cylinder screw Zylinderkopfschraube DIN 912 - M8 x 30
15.16 4 017724 Washer Scheibe DIN 9021 - 6,4
37.00 1 043815 Steering head Lenkerkopf
37.01 1 047208 Connecting piece Absaugstutzen
37.02 1 014817 Hexagon nut Sechskantmutter DIN 985 - M10
37.03 1 018216 Headless pin Gewindestift DIN 913 - M10 x 20
37.04 2 014808 Flat head screw Flachkopfschraube DIN 923 - M6 x 5
38.00 1 016615 Steering head cover Gehäuseabdeckung
38.01 2 017727 Counter sunk screw Senkschrauben mit Innensechskant DIN 7991 - M5x20
38.02 1 016312 Counter sunk screw Senkschrauben mit Innensechskant DIN 7991 - M5x16
38.04 1 016618 Ring nut Ringmuttern DIN 582 - M8
38.06 1 017651 Cylinder screw Zylinderkopfschraube DIN 912 - M8 x 16
39.00 1 016521 Pier for cable clip Kabelhalterstütze
39.01 2 043888 Counter sunk screw Senkschrauben mit Innensechskant DIN 7991 - M6x16
39.03 1 043827 Dressure spring Druckfeder
39.04 1 018737 Washer Scheibe DIN 9021 - 8,4
40.00 1 014548 Cable arm Kabelhalterarm
41.00 1 047308 Dust pipe Staubrohr
42.00 1 047303 Contr. rod Zugstange
43.00 1 016628 Drum lifting grip Abhebegriff
43.01 1 043831 Circlip Federring DIN 128 - A10
43.02 1 016629 Spacer Distanzbüchse
43.04 1 017678 Cylinder screw Zylinderkopfschraube DIN 912 - M6 x 30
43.05 1 043838 Shrinking hose Schrumpfschlauch
44.00 1 016632 Angle joint Winkelgelenk
44.01 1 016633 Cylinder screw Zylinderschraube DIN 912 - M6 x 150
44.03 1 016635 Ring bolt Ringschraube DIN 444 - A - M6 x 35
44.06 1 016638 Pressure spring Druckfeder
44.07 1 014827 Washer Scheibe DIN 125-1 - B 6,4
44.08 1 043882 Guard cover Schutzkappe
46.00 1 047304 Axle Welle f. Absenkung
46.03 2 016396 Spacer Distanzbüchse
46.04 1 047385 Rounded head screw Linsenflanschkopfschraube ISO 7380 - M8 x 20
46.05 1 036222 Adjusting washer Stützscheibe DIN 988 - S12 x 18
46.06 2 017676 Hexagon nut Sechskantmutter, dünn ISO 4035 - M8
46.10 2 047218 Bushing DU Buchse
46.11 1 047216 Ring bolt Ringschraube DIN 444 - A - M8 x 40
47.00 1 047301 Handlehold Griffrohr
47.01 2 047310 Grip covering Griffbezug
49.00 2 047214 Stud bolt Stiftschraube DIN 835 - M10 x 80
49.01 1 014788 Stud bolt Stiftschraube DIN 835 - M10 x 60
50.01 1 047220 Ball handle Kugelknopf
67.01 2 047796 Wing nut Flügelmutter
Page 48
48 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
97.01
92.00
75.01
83.01
95.00
80.01
84.00
83.00
80.00
97.03
97.02
97.00
90.01
90.00
94.01
90.02
95.00
85.00
85.01
85.02
80.00
92.01
75.08
75.06
75.05
75.07
75.14
75.16
75.15
82.00
75.17
75.13
98.06
98.05
98.04
94.00
98.02
75.00
76.00
9. Motor: Python C 3,2kW/50Hz
Item no 048666
Page 49
2. Motor komplett: COBRA 3,68kW/60Hz
2. Motor complete: COBRA 3,68kW/60Hz9. Motor: Python C 3,2kW/50Hz
Item no 048666
49 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Pos Pcs Ref Bezeichnung Description Werkstoff/Norm
75.00 1 048530 Motor Motor 3,2 kW/50Hz
75.01 1 Chassis Motor Motorgehäuse m. Stator 3,2 kW/50Hz
75.05 1 048059 Thread rod Gewindestange M 10x200
75.06 1 017667 Hexagon nut Sechskantmutter DIN 936 - M10
75.07 1 043834 Flat knurled nut Rändelmutter DIN 467 - M10
75.08 1 043897 Star grip Sterngriff M10
75.13 1 043858 Motor base Motorsockel
75.14 4 017060 Hexagon bolt Sechskantschraube DIN 933 - M8 x 30
75.15 4 018737 Washer Unterlegscheibe DIN 9021 - 8,4
75.16 4 016455 Circlip Federring DIN 127 - A 8
75.17 1 043857 Tube motor base Motorsockel Rohrstück
76.00 1 048656 Motor complete PYTHON Motor komplett PYTHON 3,2 kW/50Hz
80.00 8 043836 Winding screw Gewindefurchende Schraube DIN 7500 M6 x 30
80.01 2 043920 Cylinder screw Zylinderschraube mit Schlitz DIN 84 - M5 x 35
82.00 1 016603 Knurled nut Rändelmutter M16
83.00 1 043909 Front bearing cover Vorderes Lagerschild
83.01 1 043847 Bearing cover Lagerdeckel
84.00 1 014853 Outer packing ring Sicherungsringe für Wellen DIN 471 - 30x1,5
85.00 1 043840 Rear bearing cover hinteres Lagerschild
85.01 1 043913 Ring Wellenring
85.02 1 043824 Spacer Distanzscheibe
90.00 1 043906 Fan cover Ventilatorhaube
90.01 4 043887 Hexagon screw Sechskantschraube DIN 933 - M4 x 6
90.02 4 043830 Circlip Federring DIN 127 - A 4
92.00 1 Rotor with axle Rotor m. Welle 3,2 kW/50Hz
92.01 1 043862 Drum parallel key Paßfeder DIN 6885 - A 8 x 7 x 14
94.00 1 043860 Motor fan Motorventilator
94.01 1 043893 Outer packing ring Sicherungsringe für Wellen DIN 471 - 28x1,5
95.00 2 043845 Ball bearing Kugellager, einreihig 6206-2RS
97.00 1 043856 Motor pulley Motorriemenscheibe
97.01 1 018251 Cylinder screw Zylinderkopfschraube DIN 912 - M8 x 65
97.02 1 016612 Washer U-Scheibe DIN 440-9
97.03 1 043903 Washer U-Scheibe DIN 522-8,4 x 40x2
98.02 1 043884 v-belt guard Schutzblech
98.04 2 043917 Cylinder screw Zylinderkopfschraube DIN 7984 - M8 x 55
98.05 2 017631 Counter sunk screw Senkschraube DIN 7997 - M8 x 50
98.06 1 043821 Spacer Distanzring
100.00 1 043910 drum V-belt Walzen Keilriemen XPZ 962
101.00 1 014596 fan V-belt Ventilator Keilriemen X10x732
Page 50
50 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
10. Switch housing:
Python C 3,2kW/50Hz
Item no 048666
77.10
77.00
76.04
77.01
76.01
77.05
77.08
77.06
77.09
77.08
76.05
77.04
77.11
76.03
76.03
77.20
Pos Pcs Ref Description Bezeichnung Werkstoff/Norm
76.01 4 049052 Thread-rolling screw Gewindefurchende Schraube DIN 7500- M5 x 16 - 4.8 - Z
76.03 1 048534 Switch housing Schalterkasten
76.04 4 014805 Raised-head screw Linsenschraube DIN 7985 (H) - M4x20-H
76.05 2 017676 Hexagon nut Sechskantmuttern DIN 936 - M8
77.00 1 049068 Switch Schalter
77.01 2 043843 Capacitor 60 µF Kondensator 60 µF
77.04 1 043911 Connector 16A Einbaustecker CEE 16A
77.05 2 043890 Counter sunk screw Senkschraube DIN 965 - M5 x 12
77.06 1 043875 Switch toggle Schalterknebel
77.08 1 043877 Position label BG Schalterpositionsschild
77.09 2 043851 Raised-head screw Linsenschrauben DIN 7985 - M4x10
77.10 2 016321 Serrated lock washer Fächerscheibe DIN 6798 - A 8,4
77.11 2 049052 Thread-rolling screw Gewindefurchende Schraube DIN 7500 - M5 x 16 - 4.8 - Z
77.20 1 048639 Switch housing compl. Schalterkasten kompl.
Page 51
16
17
18
Accessories:
Python C 3,2kW/50Hz
Item no 048666
Pos Ref Description Bezeichnung
1 013839 dust bag Staubsack
2 016813 Multiclip Multiclip
3 048641 cable with plug and coupling Netzkabel mit Stecker und Kupplung
4 049275 operating instructions Bedienungsanleitung
5 048655 running wheel adjusting tool Laufrollen-Einstellgerät
6 016459 tool pouch, empty Werkzeugtasche, leer
7 016842 fork wrench 10 mm Einmaulschlüssel 10 mm
8 016799 fork wrench 13 mm Einmaulschlüssel 13 mm
9 018635 fork wrench 24 mm Einmaulschlüssel 24 mm
10 043825 double fork wrench 30/36 mm Doppelmaulschlüssel 30/36 mm
11 014956 hexagon socket screw key 5 mm Sechskant-Schraubendreher 5 mm
12 014957 hexagon socket screw key 6 mm Sechskant-Schraubendreher 6 mm
13 018641 hexagon socket screw key 10 mm Sechskant-Schraubendreher 10 mm
14 015315 hearing protectors Kapselgehörschutz
15 016732 respirator Atemschutzmaske
16 043910 drum V-belt XPZ 962 Walzen Keilriemen XPZ 962
17 014596 fan V-belt X10x732 Ventilator Keilriemen X10x732
18 016357 Tool kit complete Werkzeugsatz komplett
51 02/2008
Operating instructions
Parquet floor sander PYTHON C 3,2kW/50Hz
with gentle lifting lever
Page 52
52 02/2008
Operating instructions
Parquet floor sander Python C 3,2kW/50Hz
with gentle lifting lever
Wiring diagram: Python C 3,2kW/50Hz
Item no 048666
Circuit diagram Python C 3,2kW/50H,
Item no 048666
L1 L2 Grd.
Loading...