FPV Racing Rush Tank User Manual

TANK Series 5.8GHz Video Transmitter
PROFESSIONAL
FPV VIDEO
TRANSMITTER
MODULE
5.8G
H
Z
Model
:
TANK
48CH 0-25-200-500-800mW 7-25V 5VDC IN DC OUT
TBS
SMARTAUDIO INSIDE
TM
ANT
MMCX
POWER/PIT
7-36V HVDC-IN
5V 1A DC-OUT
SMARTAUDIO
LOCK-ON
TECHNOLOGY
INSIDE
AGC
MIC
USER MANUAL
!
WARNINGS Read this user manual before use.
● The user needs to have relevant professional knowledge while mounting or operating the VTX product, any illegal use may cause potential danger.Please ensure that you have the skills of operating radio equipments, or operate under the guidance of a professional.Read this manual carefully before you use.For those who ignore the following statement or violate the operating regulations, the user assumes the responsibility for any personal injury and property damage.
●Please follow the local radio regulations, HAM licensed is required for operating on HAM channels, and HAM power levels, some channels need to be notified to the local radio regulatory agency before use. Ensure you are in accordance with all local laws and regulations about the drones and radio. It is strictly forbidden to fly in the no fly zone such as airport, military facilities and over corwds.
Specifications
ULTIMATE ULTIMATE ULTIMATE RACING
36*36*4.5mm
30-30.5mm spacing holes
6.8g
23.5*34*4.5mm
PLUS MINI
Power 25-200-500-800mW
Channel
Voltage
Audio
7-26V DC IN
No
48CH (US version has 37 channels)
Built-in
AGC MIC
28*29*4.8mm
20mm spacing holes
5.2g6.6g
7-36V DC IN
Support audio input
7-36V
21.5*34*4mm
5.7g
25-50-200-500mW
No
Software
Botton function
TANK ULTIMATE TANK ULTIMATE PLUS / RACING TANK ULTIMATE MINI
Press to set 1-8 channes, press and hold to set band.
Press to set transmit power, press and hold to switch PIT mode.
PWR PWR PWRFREQ FREQ FREQ
FREQ
PWR PWR
RUSH LOCK-ON TECH TBS SmartAudio
FREQ
LED DISPLAY
The TANK Series VTX uses 4 red channel LEDs, 3 blue band LEDs, and one RGB power LED. They display the VTX status in real time and can be linked to the SmartAudio control.
Frequency table
LED OFF
LED FLASH LED ON
BAND A BAND B BAND E BAND F RaceBAND LowRace
CHANNEL
1 2
3 4 5
6 7 8
The selections in requires HAM license to operate.legally. selections are only available on special request.
!
5865 5845
5825 5805 5785 5765 5745 5725
!
5733 5752
5771 5790 5809 5828 5847 5866
5705 5685
5665 5645 5885 5905 5925 5945
!
!
!
!
!
5740 5760
5780 5800 5820 5840 5860 5880
5658 5695
5732 5769 5806 5843 5880
!
5917
Power table
Power LED color ULTIMATE Series
GREEN 25mW
YELLOW
200mW
!
RED
500mW
PURPLE 800mW
!
!
!
5362 5399
5436 5473 5510 5547
!
!
5584 5621
RACING Series
25mW
50mW
200mW
500mW
SmartAudio
RUSH TANK has built-in SmartAudio Control Protocol.After the VTX is connected to the FC or CF receiver, the VTX parameters can be quickly set via the OSD or radio control.
1.Connect the smartaudio port to the Flight controller Free UART-TX
VTX
SA TX
2.Open BetaFlight configurator, Goto Ports tab, Select TBS SmartAudio from Peripherals drop down menu, Speed can be left at AUTO.and save settings
Peripherais
Disabled
VTX(TBS Sma
Disabled Blackbox logging
VTX(TBS SmartAudio)
VTX(IRC Tramp) Camera(RunCam Protocol) Benewake LIDAR
FC UART
RX
AUTO
AUTO
3.Turn on the radio control,THR middle,YAW left,PITCH up,Enter the OSD menu.
Mode-2 Mode-1
4.In FEATURES > VTX SA menu,you can set the transmit frequency and power.
- SMARTAUDIO ­R F5 5820 25
>BAND
CHAN (FREQ) POWER SET CONFIG BACK
SmartAudio VTX top menu(Band/Channel mode)
FATSHARK 5 5820 25 > >
Device status
Band selection
Channel selection Frequency of selected band and
channel(not selectable;read only)
RF power selection
Commence current selection
Configuration menu
For more information please visit:https://github.com/betaflight/betaflight/wiki/Unify-Smartaudio
Loading...