Foxun SX-MX88-3DCAT Quick Start Manual

Download

8x8 HDMI Matrix over Cat5e/6 cable built in wifi

Quick Start Guide

Features

• 8 HDMI input ports,8 RJ45 Output ports.

•Transmission distance up to 50m under 1080P@60Hz over Single Cat5e or Cat6 cable.

•Transmission distance up to 30m under 1080P@60Hz over double Cat5e or Cat6 cable,support HDCP.

•Independent switch able EDID function for choosing which resolution to display.

•Supports LPCM 7.1 channel output from each of the independent HDMI ports.

•Switching modes: panel buttons, local IR, RS232 and Smart phone.

•Support HDCP .

Compliant HDCP.

•1U'srack design for easy installation.

•Support 3D.

•With WIFI .

TABLE OF CONTENTS Package Contents Dimensional drawing Specications Panel Descriptions Connecting and Operating Typical Application Maintenance Product Service Warranty

Dimensional drawing

280mm

Packing contents

1) Main Unit: 8x8 HDMI Matrix

2) Power supply DC 12V 4A

3) Remote Controller

4) IR-RX cable x 1PCS

5) M3x5 Screw x 8PCS

6) Operating Instructions

7) Mounting ear

8) RS232 cable

463.5mm

42.5

436.5mm

-5 to +35 C(+23 to +95

5 to 90%RH (No Condensation)

225MHz/6.75Gbps

Up to 1080p@60Hz@24 b/pixels, support 3D

HDMI receptacle. RJ45 receptacle

Power connector terminal Power DC receptacle IR Extender

1080P 30m over Dual Cat5e/6 cable , support HDCP. 1080P 50m over Single Cat5e/6 cable

※

Note: Please restart the matrix after changing the mode between double lan cable and single lan cable.

110-240V/ 12VDC power supply 24Watts

Cold-Rolled (Cold Rolled) Steel

W436.5xH280xT42.5mm

3800g

Front Panel

This monitor displays your settings information with each output and input selection

IR windows:: infrared sensor receive any IR commands from the IR remote control.

OUT 1~8 & IN 1~8: . First select any output port from 1-8, wait 1 sec, then choose the desired input port from ports 1-8. Each output selection only allows a single input setting each time.For Example: First select output port 5,wait 1 sec, then choose Input port 2,then “5-2” showed on the monitor displays. ”5-2” LED lit means output 5 select input 2 as it’s source.

ALL: Press this button to set all the outputs to display the same input source. First pressing the “All”button then,press an input number to conﬁrm the selection. D/S: Press this button to switch between Double LAN cable mode and single LAN cable mode. WIFI: This slot is used to install the antenna. Assembly ear

5 6

ALL: Press this button to set all the outputs to display the same input source. First pressing the “All”button then,press an input number to conﬁrm the selection.

D/S: Press this button to switch between Double LAN cable mode and single LAN cable mode.

WIFI: This slot is used to install the antenna. Assembly ear

Connecting and operating

1) Connect the HDMI input sources into 8x8 HDMI Matrix and note the input chosen.

2) Connect RJ45 OUT of HDMI matrix with input port of receiver (If using single cat5e/6 cable, please

Connecting and operating

3) Connect HDMI OUT of HDMI receiver to display equipment.

1) Connect the HDMI input sources into 8x8 HDMI Matrix.

2) Connect RJ45 out port of HDMI matrix with input port of receiver (When connect single cat5e/6 cable, please connect the receiver to Video outputs).

3) Connect HDMI receiver to display equipment by HDMI Cable.

4) Plug IR extension cable in IR extension port on the 8x8 HDMI Matrix

frame /bezel or the display stand. Note：

6) Choose the desired input source by pressing panel button, local IR,RS232 or smart phone.

6) Power up all units, ,

※

Note: Please restart the matrix after changing the mode between double lan cable and single lan cable.

3 4

RS232 port :For HDMI Matrix control on PC.

RS232 port :For WIFI module setup.

HDMI input ports(HDMI or DVI) .

RS232 port :For HDMI Matrix control on PC.

RJ45 ports: Video outputs (When using single Cat5e/6 cable, just need connect receiver to this port ).

RS232 port :For WIFI module setup.

RJ45 ports:DDC outputs.

HDMI input ports(HDMI or DVI) . RJ45 ports: Video outputs (Whe

4 5

RJ45 ports:DDC outputs.

cable ( support 38KHz).

POWER: Press this button to turn the system on.

Power input : Plug the 12V 4A DC power supply into the unit and connect the adaptor to

IR extension port : This slot is where you can extend your IR receiver with an IR extender

an AC wall outlet.

cable ( support 38KHz). Power input : Plug the 12V 4A DC power supply into the unit and connect the adaptor to

3 4

n connect a

Rear Panel

single Cat5e/6 cable, just need connec

an AC wall outlet.

connect the receiver to this port

, ,5) Power up all units the matrix,Receiver sources and displays.

IR,RS232 or smart phone.

t the

receiver to this port ).

Operation

1-1

2-2

3-3

4-4

5-5

6-6

7-7

8-8D

D/S

1. Front panel control There are

port selects this input as its source.For eg.”5-8” led lit,means output5 is selecting input8 source.

four groups of LEDs for each output port. The LED lit on the position means that the output

4. RS232 remote control.

1. The Message Window

2. Local IR remote control User can control the HDMI route of the matrix by using the IR remote.

There are two group key pads for sixteen ports. Press the desired output source button, then press desired input button.

Out 8,then press

In 7,LCD will display “8-7”)

3. IR extension control User can use the IR receiver cable to change the IR receive r

position.

If controlling the HDMI matrix by remote control , connect the IR cable directly to the

(Connect the computer and R232 Port 1 by RS232 Cable)

matrix rear IR Ext socket. (1/8” (3.5 mm) input jack).

2.1 Receive Window The “receive window” will show the message received from matrix. When you click the Control Buttons (see step 4) or send Control Command (see 2.3) to matrix, it will send out the message about “operation results” as right:

2.2 Status Button Click this button to read the status of Matrix. The status is about which input is selected by the output.

2.3 Send Window Input the control command in this window. The control command use ASCII.

3. The Com Status

3.1 connect state. Connect state shows the com connected or not. If it is connected, the state is green. Otherwise, the state is red.

3.2 com select. Select which com you will use. Click “Connect ” button to open the com.

Click “disconnect” button to close the com.

3.3 Com port setting(for 2 RS232 port):

Baud Rate: 9600 bps Data bits: 8 bits Parity: None Stop bits: 1 bit Flow control: None

4 Setting Button Click this button to enter Setting menu. If the signal is not stable, please turn on the S mode(Transmitter HDMI OVER sigle cat5e cable) .

4.1 EDID Set button

1).Select the Output Port in “Port Select” column, click “Read EDID” button to get EDID from display equipment.

2).Select the Input Port in “Port Select” column, click “Download” button to set EDID of this Input Port same as display equipment.

3).

4).Click “Open EDID” button to

the Input Port in “Port Select” column,

5).click “Download” button to set EDID of this Input Port

5.Android OS control

5.1 Install android apk(Matrix88.apk)

5.2 Connect device

(10.10.100.254), then click “connect” to enter.

Main menu

6.IOS control

6.1 Go to “App store ”， search “Matrix88” ,download and install the APP.

6.2 Connect device Set the Wi in your iPhone/iPad ,run “Matrix88”, input equipment WIFI module’s IP address (10.10.100.254) ,then click “Button” to enter.

Main menu

RS-232 pin assignment

HDMI Matrix

1 2

3 4 5 6 7 8

Assignment

NC TX

GND

NC NC NC NC

Remote Control Console

Assignment

1 2 RX

5 6 7 8 9

GND

NC NC NC NC

DVD PC HD camera IPTV

Blue-ray player

TV1

TV5 TV6 TV7 TV8

PS3 Xbox STB

HDMI matrix

RX RX RX

TV2 TV3 TV4

RX RX RX RX

HDMI cable

Dual Cat5e/6 cable

RS-232 Commands

(The symbol "_ " in the belowing command means : Press the space key )

command

cir_0x\r\n

cir_1x\r\n 63 69 72 20 31 xx 0D 0A s2y

cir_2x\r\n 63 69 72 20 32 xx 0D 0A s3y

cir_3x\r\n 63 69 72 20 33 xx 0D 0A s4y

cir_4x\r\n 63 69 72 20 34 xx 0D 0A s5y

cir_5x\r\n 63 69 72 20 35 xx 0D 0A s6y

cir_6x\r\n 63 69 72 20 36 xx 0D 0A s7y

cir_7x\r\n 63 69 72 20 37 xx 0D 0A s8y

asw_x\r\n 61 73 77 20 xx 0D 0A s1y s2y

bc_\r\n 61 73 77 20 xx 0D 0A s1x s2x

sed_x_y\r\n 73 65 64 20 xx yy 0D 0A sed_x_y

rst_\r\n 72 73 74 20 0D 0A

HEX

63 69 72 20 30 xx 0D 0A

s1y

Output 1 select input 1~8 “x” : indicate the input port, range from 0~7. “y” : indicate the input port, range from 1~8.

Output 2 select input 1~8 “x” : indicate the input port, range from 0~7. “y” : indicate the input port, range from 1~8.

Output 3 select input 1~8 “x” : indicate the input port, range from 0~7. “y” : indicate the input port, range from 1~8.

Output 4 select input 1~8 “x” : indicate the input port, range from 0~7. “y” : indicate the input port, range from 1~8.

Output 5 select input 1~8 “x” : indicate the input port, range from 0~7. “y” : indicate the input port, range from 1~8.

Output 6 select input 1~8 “x” : indicate the input port, range from 0~7. “y” : indicate the input port, range from 1~8.

Output 7 select input 1~8 “x” : indicate the input port, range from 0~7. “y” : indicate the input port, range from 1~8.

Output 8 select input 1~8 “x” : indicate the input port, range from 0~7. “y” : indicate the input port, range from 1~8.

All output select input x;

s3y s4y

“x” : indicate the input port, range from 0~7.

s5y s6y

“y” : indicate the input port, range from 1~8.

s7y s8y

Obtain the input status.

s3x s4x

“x” : indicate the input port, range from 1~8. s5x s6x s7x s8x

Copy edid from “x” to “y”,

“x””y” range from 0~7

Reset factory settings

descriptionfeedback

Foxun SX-MX88-3DCAT Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual