Foxfury Lighting Solutions Nomad Prime, Nomad P56, 200-800, 200-800-TC, 200-8P56 Product Manual

PRODUCT MANUAL

200-800 | 200- 800-TC | 200-8P56

NOMAD® PRIME & P56

2

TABLE OF CONTENTS

INTRODUCTION

Reference Guide 3

Overview 4

Physical Characteristics 4

BATTERY

Charging the Batteries 5

Charging from a 12VDC Vehicle Adaptor 5

Charge Indicator 5

OPERATION

AC-DC Adaptor and International Use 6

Operational Modes 6

Battery Life 7

Battery Life Indicator 7

Using the Nomad® while Plugged in 7

FEATURES

Swivel and Tilt Light Head 8

Diffuser Lens (Area-Spot) 8

Swivel and Tilt Light Head 9

Leveling Leg Extensions and Level Bubble 9

Anchor Strap 9

DEPLOYING THE NOMAD

®

10–11

MAINTENANCE 12–17

WARRANTY 18–19

CONTACT FOXFURY 19

3

NOMAD® REFERENCE GUIDE

BATTERY SYSTEM/
NOMAD

®

BODY

POWER/MODE

SWITCH

CARRY
STRAP

CLIP
BATTERY LIFE/
CHARGE INDICATOR

LEVEL BUBBLE

ANCHOR

STRAP

CHARGING PORT

PROTECTIVE
LIGHT CAP

LOCKING SLEEVE

TRIPO-SCOPE

®

POLES

TRIPO-SCOPE

®

TIGHTENING
RINGS (3)

FOLDING

TRIPO-SCOPE

®

LEGS (3)

TRIPO-SCOPE

®

LEG LOCK

LEVELING LEG

EXTENSIONS

DIFFUSER LENS
(AREA-SPOT)

TILT ADJUSTMENT

KNOB

SWIVEL ADJUSTMENT
KNOB (340º)

LIGHT HEAD

ALSO INCLUDED

Accessories Bag

3M (Yellow) Reflective Tape

Carry Strap

AC-DC Adaptor

AC Cable

12VDC Vehicle Adaptor

DEPLOYED VIEW

STORED POSITION

4

OVERVIEW

The Nomad® Prime & P56 provide 3–24 hours of continuous lighting. It
converts from an area light to spotlight in seconds by attaching/detaching the
Diffuser Lens. Its portable, waterproof and adaptive design allows it to be
used in places where other area lights cannot. You can use it as a bazooka
light to survey an area or illuminate your path. In around 20 seconds, you’ll be
able to deploy the self-contained Tripo-Scope® Legs and raise the telescoping
head up to 8 ft tall to illuminate the work area.

IMPORTANT!

Please fully charge the Battery System before using the Nomad® for the
first time.

PHYSICAL CHARACTERISTICS

Please read below before using the Nomad® as it relays beneficial operating
and safety information.

NOMAD® PRIME & P56

DIMENSIONS 34.4 x 4.6 in (874 x 117 mm)

WEIGHT

18.4 lbs (8.3 kg)

WARNINGS

When used for extended periods of time the Nomad® will become HOT to
the touch. Please use care when operating.

Do not stare into LEDs for long periods of time or from a close range
(less than 2 ft).

Be sure to rinse the Nomad® with fresh water immediately after use in
the ocean or a pool.

This product may contain chemical(s) known to the State of California
to cause cancer, birth defects or other reproductive harm. For more
information, go to www.P65Warnings.ca.gov/product.

!

!

!

5

CHARGING THE BATTERIES

1. Start with the AC Cable. Connect it to the AC-DC Adaptor.

The AC Cable is Universal to NEMA 5-15P, 3 prong for USA and will
work with a power range of 100VAC–240VAC 50/60 Hz.

2. Plug the Barrel Connector (part of the AC-DC Adaptor) into the Charging

Port of the Nomad® Prime or P56.

Input voltage: 11–17VDC. Do NOT exceed!

The Nomad® Prime is shipped with a 30% charge. It is important to
charge it before using for the first time.

When the Charge Indicator FLASHES green it indicates that the
battery is being charged. When the Nomad® is completely charged, the
Charge Indicator will turn solid green.

Charging time will be approximately 5 hours.

CHARGING FROM A 12VDC VEHICLE ADAPTOR

1. Insert the 12VDC Vehicle Adaptor Cable into a 12V socket (located within

the vehicle).

2. Insert the opposite end (Barrel Connector) into the Charging Port of the

Nomad® Prime or P56.

NOTE: Do NOT start vehicle while the Nomad® is plugged in.

CHARGE INDICATOR

(FOR LOCATION, PLEASE REFERENCE PAGE 3)

COLOR DESCRIPTION

GREEN (SOLID) FULLY CHARGED

GREEN (FLASHING) CHARGING

RED (SOLID) CHARGING ERROR

*If a charging error occurs, please contact FoxFury Customer Service (see pg. 18).

NOTE: Continuously charging (leaving the unit plugged in) could damage the
Battery Pack and lead to a decreased battery life. Please disconnect the unit
once it is fully charged.

Please DO NOT leave AC-DC Adaptor plugged in for more than eight (8)
continuous hours.

1

1

2

2

6

AC-DC ADAPTOR AND INTERNATIONAL USE

The Nomad® Series has a AC-DC Adaptor which uses AC Cables like those
used in desktop computers or monitors. With every Nomad®, FoxFury supplies
a cable that terminates in the USA standard 110 VAC plug.

The plug of the AC Cable should be country specific. Example: IEC Types A-N.
The Female Connector side of the AC Cable must be IEC Type C13 to mate
with the Male Inlet of the AC-DC Adaptor.

ON/LOW mode: Press the Power/Mode Switch once.

MEDIUM mode: From LOW mode, press the Power/Mode Switch once.

HIGH mode: From MEDIUM mode, press the Power/Mode Switch once.

FLASHING mode (excludes Nomad

®

P56): From HIGH mode, press the

Power/Mode Switch once.

OFF: From HIGH/FLASHING mode, press the Power/Mode Switch once.

NOTE: The light does not retain the mode in memory. Once the light is ON,
re-select the mode desired.

OPERATIONAL MODES

AC CABLE

TYPE B

10A (250V)

INLET (MALE) (C14 IEC)

(LOCATED AT END OF

ADAPTOR)

CONNECTOR
(FEMALE) (C13 IEC)

(VIEW OF CABLE END)

AC-DC ADAPTOR

BARREL CONNECTOR

CONNECTOR (FEMALE) AC PLUG

MUST BE IEC C13

CONNECTOR

CAN BE ANY PLUG

IEC TYPES A-N

AC CABLE

10A (250V)