Foxfury Lighting Solutions Nomad N32, Nomad N56, 200-4N32, 200-4N56 Product Manual

PRODUCT MANUAL

200–4N32 | 200–4N56

NOMAD® N32 & N56

2

TABLE OF CONTENTS

INTRODUCTION

Reference Guide 3

Overview 4

Physical Characteristics 4

BATTERY PACK

Charging the Battery Pack 5

Charging from a 12VDC Vehicle Adaptor 5

Charge Indicator 5

OPERATIONAL MODES

AC - DC Adaptor and International Use 6

Operational Modes 6

Battery Life 7

Battery Life Indicator 7

Using the Nomad® while Plugged in 7

FEATURES

Swiveling Light Head 8

Sliding Diffuser Lens 8

Remote Key Fob Use 9

MOUNTING THE NOMAD

®

Magnetic Mount 10

Stacking 10

ACCESSORIES (NOT INCLUDED)

Horizontal Right Angle Mount 10

Utility Mount 11

Wall Mount Kit 11

Tripo-Scope® M1, Tripod and FoxFury Puck Adaptor 11

MAINTENANCE 12–14
WARRANTY 15–16
CONTACT FOXFURY 16

3

NOMAD® REFERENCE GUIDE

COLLAPSIBLE

HANDLE

SLIDING DIFFUSER LENS

(AREA-SPOT)

REMOTE SWITCH

SWIVELING

LIGHT HEAD

¼"-20 MOUNT

(ON TOP & BOTTOM)

BATTERY LIFE/
CHARGE INDICATOR

MAGNETIC/WALL

MOUNT HOLES (4)

CHARGING PORT

POWER/MODE SWITCH

REMOTE SWITCH

INDICATOR

ALSO INCLUDED

12VDC Vehicle Adaptor

Small FoxFury Duffel Bag

All Thread ¼"-20 Screw

Remote Key Fob

Magnetic Mount

AC-DC Adaptor

AC Cable

4

OVERVIEW

The Nomad® N32 & N56 deliver studio quality lighting outside of the studio.
Models can be magnet and tripod mounted and feature a rechargeable Li-ion
Battery Pack providing 3– 24 hours of light. They shine bright in any weather
and can even be fully submerged. The N32 delivers up to 2,400 lumens of
3,200 Kelvin (tungsten) light with a high CRI of 95 for precise color rendering.
The N56 delivers up to 2,700 lumens with a color temperature of 5,600 Kelvin
(daylight) with a high CRI of 95 for precise color rendering.

IMPORTANT!

Please fully charge the battery before using the Nomad® for the first time.

PHYSICAL CHARACTERISTICS

Please read below before using your Nomad® as it relays beneficial operating
and safety information.

NOMAD® N32 & N56

DIMENSIONS 8.7 x 5.3 x 4.3 in (221 x 135 x 110 mm)

WEIGHT

4.5 lbs (2 kg)

WARNINGS

When used for extended periods of time the Nomad® Light Head will
become HOT to the touch. Please use care when operating.

Do not stare into LEDs for long periods of time or from a close range
(less than 2 ft).

Be sure to rinse the Nomad® with fresh water immediately after use in
the ocean or a pool.

!

!

5

CHARGING THE BATTERY PACK

1. Start with the AC Cable. Connect it to the AC - DC Adaptor.

The AC Cable is Universal to NEMA 5-15P, 3 prong for USA and will
work with a power range of 100VAC–240VAC 50/60 Hz.

2. Then, plug the Barrel Connector (part of the AC-DC Adaptor) into the
Charging Port of the Nomad®.

Input voltage: 11–17VDC. Do NOT exceed!

The Nomad® is shipped with a 30% charge. It is important to charge it
before using it for the first time.

When the Charge Indicator FLASHES green it indicates that the
Battery Pack is being charged. When the Nomad® is completely
charged, the Charge Indicator will turn solid green.

Charging time will be approximately 4 hours.

CHARGING FROM A 12VDC VEHICLE ADAPTOR

1. Insert the 12VDC Vehicle Adaptor into a 12V socket (located within the
vehicle).

2. Then, insert the opposite end (Barrel Connector) into the Charging Port of
the Nomad®.

NOTE: Do NOT start vehicle while the Nomad® is being charged or when using
while plugged in.

CHARGE INDICATOR

(FOR LOCATION, PLEASE REFERENCE PAGE 3)

COLOR DESCRIPTION

GREEN (SOLID) FULLY CHARGED

GREEN (FLASHING) CHARGING

RED (SOLID) CHARGING ERROR

*If a charging error occurs, please contact FoxFury Customer Service (see pg. 16).

NOTE: Continuously charging (leaving the unit plugged in) could damage the
Battery Pack and lead to a decreased battery life. Please disconnect the unit
once it is fully charged.
Please DO NOT leave AC-DC Adaptor plugged in for more than eight (8)
continuous hours.

6

AC-DC ADAPTOR AND INTERNATIONAL USE

The Nomad® Series has a AC - DC Adaptor which uses AC Cables like those
used in desktop computers or monitors. With every Nomad®, FoxFury supplies
a cable that terminates in the USA standard 110 VAC plug.

The plug of the AC Cable should be country specific. Example: IEC Types A-N.
The Female Connector side of the AC Cable must be IEC Type C13 to mate
with the Male Inlet of the AC-DC Adaptor.

ON/LOW mode: Press the Power/Mode Switch once.

MEDIUM mode: From LOW mode, press the Power/Mode Switch once.

HIGH mode: From MEDIUM mode, press the Power/Mode Switch once.

OFF: From HIGH mode, press the Power/Mode Switch once.

NOTE: The light does not retain the mode in memory. Once the light is ON,
re-select the mode desired.

OPERATIONAL MODES

AC CABLE

TYPE B

10A (250V)

INLET (MALE) (C14 IEC)

(LOCATED AT END OF

ADAPTOR)

CONNECTOR
(FEMALE) (C13 IEC)

(VIEW OF CABLE END)

AC-DC ADAPTOR

BARREL CONNECTOR

CONNECTOR (FEMALE) AC PLUG

MUST BE IEC C13

CONNECTOR

CAN BE ANY PLUG

IEC TYPES A-N

AC CABLE

10A (250V)