Foxfury Lighting Solutions NOMAD 360, NOMAD T32, NOMAD T56 Product Manual

PRODUCT MANUAL

200-900 | 200- 900-TC | 200-9T32 | 200-9T56

NOMAD® 360, T32 & T56

2

TABLE OF CONTENTS

INTRODUCTION

Reference Guide 3

Overview 4

Physical Characteristics 4

BATTERY

Charging the Battery System 5

Charging from a 12VDC Vehicle Adaptor 5

Charge Indicator 5

OPERATION

AC-DC Adaptor and International Use 6

Operational Modes 6

Battery Life 7

Battery Life Indicator 7

Using the Nomad

®

while Plugged in 7

FEATURES

Light Head Configuration 8

Sliding Diffuser Lens (Area-Spot) 8

Swivel and Tilt Light Head 9

Leveling Leg Extensions and Level Bubble 9

Anchor Strap 9

DEPLOYING THE NOMAD® 10-11

ACCESSORIES (NOT INCLUDED)

12

MAINTENANCE 12–17

WARRANTY

18–19

CONTACT FOXFURY 19

3

360 REFERENCE GUIDE

BATTERY SYSTEM/
NOMAD

®

BODY

POWER/MODE

SWITCH

CARRY
STRAP

CLIP
BATTERY LIFE/
CHARGE INDICATOR

LEVEL BUBBLE

ANCHOR

STRAP

CHARGING PORT

PROTECTIVE
LIGHT CAP

LOCKING SLEEVE

TRIPO-SCOPE

®

POLES

TRIPO-SCOPE

®

TIGHTENING RINGS

FOLDING

TRIPO-SCOPE

®

LEGS (3)

TRIPO-SCOPE

®

LEG LOCK

LEVELING LEG

EXTENSIONS

SLIDING DIFFUSER LENS
(3) (AREA-SPOT)

TILT ADJUSTMENT KNOB

SWIVEL ADJUSTMENT
KNOB (340º)

LIGHT HEAD

ALSO INCLUDED

Accessories Bag

3M Reflective (Yellow) Safety Tape
Strips, set of 3

Nomad® Carry Strap

AC-DC Adaptor

AC Cable

12VDC Vehicle Adaptor

DEPLOYED VIEW

STORED POSITION

4

OVERVIEW

The Nomad® 360 ultimate scene light can provide up to 7,000 lumens on HIGH
Power. Its portable, submersible and self-contained design allows it to travel
to (and be used in) places that standard scene lights and vehicle mounted
lights cannot reach. In around 20 seconds, deploy the Tripo-scope® Legs and
raise the telescoping head up to 8½ ft tall to illuminate the work area. Its
rechargeable and cordless design means no noisy, heavy generator is needed.

The portable Nomad® T32 & T56 deliver studio quality lighting outside of
the studio. They shine bright in any weather and can even be submersed
for cleaning or filming. The T32 delivers up to 7,000 lumens of 3,200 Kelvin
(tungsten) light with a high CRI of 95 for precise color rendering. The T56
delivers up to 8,200 lumens with a color temperature of 5,600 Kelvin (daylight)
with a high CRI of 95 for precise color rendering. Durable enough to withstand
strong winds, this compact unit with Folding Tripo-Scope® Legs features a
telescoping pole and a Level Bubble.

IMPORTANT!

Please fully charge the Battery System before using the Nomad® for the first
time.

PHYSICAL CHARACTERISTICS

Please read below before using the Nomad® 360 as it relays beneficial
operating and safety information.

NOMAD®

DIMENSIONS 39.9” x 4.6" (101.4 x 11.7 cm)

WEIGHT 24 lbs (11 kg)

WARNINGS

When used for extended periods of time the Nomad® Light Head will
become HOT to the touch. Please use care when operating.

Do not stare into LEDs for long periods of time or from a close range
(less than 2 ft).

!

5

CHARGING THE BATTERIES

1. Start with the AC Cable. Connect it to the AC-DC Adaptor.

The AC Cable is Universal to NEMA 5-15P, 3 prong for USA and will
work with a power range of 100VAC–240VAC 50/60 Hz.

2. Then, plug the Barrel Connector (part of the AC-DC Adaptor) into the

Charging Port of the Nomad®.

Input voltage: 11–17VDC. Do NOT exceed!

The Nomad® 360 is shipped with a 30% charge. It is important to
charge it before using for the first time.

When the Charge Indicator FLASHES green it indicates that the
battery is being charged. When the Nomad® is completely charged, the
Charge Indicator will turn solid green.

Charging time will be approximately 7 hours.

CHARGING FROM A 12VDC VEHICLE ADAPTOR

1. Insert the 12VDC Vehicle Adaptor into a 12V socket (located within

the vehicle).

2. Then, insert the opposite end (Barrel Connector) into the Charging Port of

the Nomad

®

.

NOTE: Do NOT start vehicle while the Nomad® is being charged or when using
while plugged in.

CHARGE INDICATOR

(FOR LOCATION, PLEASE REFERENCE PAGE 3)

COLOR DESCRIPTION

GREEN (SOLID) FULLY CHARGED

GREEN (FLASHING) CHARGING

RED (SOLID) CHARGING ERROR

*If a charging error occurs, please contact FoxFury Customer Service (see pg. 19).

NOTE: Continuously charging (leaving the unit plugged in) could damage the
Battery Pack and lead to a decreased battery life. Please disconnect the unit
once it is fully charged.

Please DO NOT leave AC-DC Adaptor plugged in for more than eight (8)
continuous hours.

6

AC-DC ADAPTOR AND INTERNATIONAL USE

The Nomad® Series has a AC-DC Adaptor which uses AC Cables like those
used in desktop computers or monitors. With every Nomad®, FoxFury supplies
a cable that terminates in the USA standard 110 VAC plug.

The plug of the AC Cable should be country specific. Example: IEC Types A-N.
The Female Connector side of the AC Cable must be IEC Type C13 to mate
with the Male Inlet of the AC-DC Adaptor.

ON/LOW mode: Press the Power/Mode Switch once.

MEDIUM mode: From LOW mode, press the Power/Mode Switch once.

HIGH mode: From MEDIUM mode, press the Power/Mode Switch once.

FLASHING mode: From HIGH mode, press the Power/Mode Switch once.

OFF: From FLASHING mode, press the Power/Mode Switch once.

*Flashing Mode not available on the Nomad® T32 & T56.

NOTE: The light does not retain the mode in memory. Once the light is ON,
re-select the mode desired.

OPERATIONAL MODES

AC CABLE

TYPE B

10A (250V)

INLET (MALE) (C14 IEC)

(LOCATED AT END OF

ADAPTOR)

CONNECTOR
(FEMALE) (C13 IEC)

(VIEW OF CABLE END)

AC-DC ADAPTOR

BARREL CONNECTOR

CONNECTOR (FEMALE) AC PLUG

MUST BE IEC C13

CONNECTOR

CAN BE ANY PLUG

IEC TYPES A-N

AC CABLE

10A (250V)