fox fury TAKER B10, 940-010FI Product Manual

PRODUCT MANUAL

940K-010S

TAKER B10

3

TAKER B10 REFERENCE GUIDE

LANYARD

HOLE

RUBBER

SLEEVE

POWER/MODE SWITCHLOCKING GROOVE

STRIKE BEZEL

ANTI-ROLL HEAD TAILCAP

HANDLE

ASSEMBLED B10

(WITHOUT FLASHLIGHT)

PICATINNY C-CLAMP

RELEASE

LEVER

PICATINNY

C-CLAMP

FRONT

THUMBSCREW

PICATINNY

RAIL

TILT

ADJUSTMENT

SCREW

CLAMP

MOUNT

SCREWS

(4)

PICATINNY MOUNT

MOUNT

MOUNT

SCREWS (4)

HOLDER

HOLDER

TABLE OF CONTENTS

INTRODUCTION

Taker B10 Reference Guide 3

Physical Characteristics & Warnings 4

BATTERY

Battery Installation and Replacement 5

Battery Life 5

OPERATION

Operational Modes 6

ASSEMBLY

Assembling Mount to Clamp 6

Inserting/Removing from the Holder 7

FEATURES

Pressure Switch 8

Tilt 8

Multiple Lights on One Shield 8

INSTALLATION

Shield Installation 9

WARRANTY 10–11

CONTACT FOXFURY 11

SIDESLIDE FLASHLIGHT

(P/N 940-010FI)

4

5

PHYSICAL CHARACTERISTICS

Please read below before using your Taker B10 as it relays beneficial
operating and safety information.

B10 FULL ASSEMBLY (WITH FLASHLIGHT) (P/N 940 K– 010S)

DIMENSIONS 4.7” x 1.5” x 5.5” (119 x 38 x 140mm)

WEIGHT 12.7oz (360g) (with no battery)

PICATINNY C-CLAMP (80-013)

DIMENSIONS 2.91” x 1.4” x 1.75” (74 x 36 x 44mm)

WEIGHT 4.9oz (139g)

BATTERIES

The Taker B10 flashlight requires one (1) 18650 battery or two (2)
CR123 batteries.

Mixing of new and used, or different brand batteries is not recommended
as this could lead to leakage or explosion.

BATTERY INSTALLATION AND REPLACEMENT

1. Twist the Tailcap in a counter-clockwise direction to remove it.

2. Insert the battery with the positive end first. (Respect appropriate polarity
when installing).

3. Reinstall the Tailcap by twisting it in a clockwise direction back onto the
Handle. (Make sure the Tailcap is tightly sealed).

4. Test the light’s performance and function by activating the Power/Mode
Switch (located at the end of the Tailcap).

BATTERY LIFE

MODE BATTERY LIFE LUMENS

MOMENTARY 1.5hrs 380

CONTINUOUS HIGH 1.5hrs 380

CONTINUOUS LOW 10hrs 70

TURBO-STROBE

™

4hrs 380

*Battery life may vary according to mode selected, battery quality and prevailing ambient conditions.

+ BATTERY –

1

2

TAILCAP

1

2

3

4

WARNINGS

Do not stare into LEDs for long periods of time or from a close range
(less than 2ft (.06m)).

FoxFury’s Turbo-Strobe™ is purposely designed to induce disorientation.
Prolonged viewing may produce vertigo or even vomiting.

!

!

INCLUDED

SideSlide Picatinny Flashlight (P/N 940K-010PIC)

Picatinny C-Clamp (85-013)

6

7

1. Begin with the Picatinny Mount. Using the provided 2mm Hex Key, loosen
ONLY two (2) of the Mount Screws (see “Taker B10 Reference Guide”
on pg. 3 for location). NOTE: The Mount Screws do NOT need to be
completely removed in order to mount.

2. Position either side of the Picatinny Mount onto the Picatinny C-Clamp.
Then position the opposite side onto the Picatinny Rail. Then, re-tighten
the two (2) Mount Screws that were loosened in Step 1.

OPERATIONAL MODES

For MOMENTARY mode: Press and hold the Power/Mode Switch. While
the Switch is depressed, the flashlight will operate in HIGH mode. When
the user removes pressure from the Switch, the light will turn OFF.

For HIGH mode: Press the Power/Mode Switch two (2) times in rapid
succession. The light will remain in HIGH mode.

For LOW mode: While in HIGH mode, press and hold the Power/Mode
Switch for two (2) seconds. The mode will change to a LOW setting.

For TURBO-STROBE™: Press the Power/Mode Switch three (3) times in
rapid succession.

For OFF or EXIT a mode: Press the Power/Mode Switch once. Then,
continue following the directions above to progress to desired mode.

NOTE: The light does not retain the mode in memory. Once you turn the
flashlight ON, you will have to re-select the mode you desire.

The flashlight is easily securable and removable by using the Release Lever.

TO INSERT THE FLASHLIGHT INTO THE HOLDER:

INSERTING/REMOVING FROM THE
HOLDER

ASSEMBLING MOUNT TO CLAMP

1. Insert the flashlight by pushing it into the beveled opening on the front of
the Holder.

2. Once locked, the Release Lever falls into a groove on the handle, securing
the flashlight in place.

TO REMOVE THE FLASHLIGHT FROM THE HOLDER:

1

2

1. Press and hold the Release Lever.

2. While keeping the Release Lever pressed, pull flashlight out of the Holder.

1

1

1

1

1

2

2

2

2

2

8

9

INSTALLING THE TAKER B10
ONTO A SHIELD

1. Loosen the Thumbscrew until the Clamp is free. Then place the Clamp
anywhere along the edge of the shield (The provided rubber spacer can
also be used if required for a better fit).

2. Then align the Clamp and Thumbscrew to the Picatinny C-Clamp Body
and tighten until the Clamp is locked securley in place.

3. To adjust the angle of the B10, use the provided Hex Key (4mm) to loosen
the Tilt Adjustment Screw (see “Taker B10 Reference Guide” on pg. 3 for
location). Then adjust the angle of the Picatinny Mount to desired position.
Re-tighten the Tilt Adjustment Screw to lock in the angle of Flashlight.

1

2

3

BALLISTIC
SHIELD

Place the shield in
between the battery
compartment and
Light Head. (The
shield pictured is cut
in half for this visual)

FRONT OF SHIELD

CLAMP

PICATINNY

C-CLAMP

THUMBSCREW

SIDE VIEW

FEATURES

PRESSURE SWITCH

The Taker B10 has an optional Pressure Switch that allows the user to place
it anywhere on the shield. This makes it easier to access the Power/Mode
Switch. The Pressure Switch can easily be attached by twisting the Tailcap in
a counter-clockwise direction to remove it, and replacing it with the Pressure
Switch.

60º TILT

The Picatinny C-Clamp of the Taker B10 can tilt 30º (60º total) on both sides.
This makes it easier to chose direction of light.

MULTIPLE LIGHTS ON ONE SHIELD

Multiple Taker B10’s can be mounted to one shield to disorient rioters.

10

11

THIS LIMITED WARRANTY SHALL
NOT APPLY IF THIS PRODUCT IS
NOT STORED, HANDLED, INSTALLED
OR USED IN STRICT ACCORDANCE
WITH MANUFACTURER’S
SPECIFICATIONS AND INSTRUCTION
MANUALS, OR WHICH HAS BEEN
SUBJECT TO MISUSE, ALTERATION,
NEGLIGENCE OR ACCIDENT.

1. The damaged part or product must
be returned to FoxFury PRIOR TO
any repair or replacement. Shipping
costs are the responsibility of the
claimant.

2. You must obtain a return
authorization (RMA) number from
FoxFury prior to returning products.
FoxFury is not responsible for any
damage incurred while in transit.

3. Buyer will be required to
show proof of purchase—NO
EXCEPTIONS.

4. Any modifications to light, cable or
battery pack automatically voids all
warranties on this product.

All warranty inquiries should be directed
to FoxFury’s Customer Service
Department at [e-mail]
to handle all warranty/repair-related
inquiries.

TO THE EXTENT ALLOWED BY
APPLICABLE LAW: (A) IN NO EVENT,
WHETHER DUE TO BREACH OF
WARRANTY HEREUNDER OR ANY
OTHER CAUSE WHATSOEVER,
SHALL FOXFURY BE LIABLE FOR
OR OBLIGATED IN ANY MANNER TO
PAY CONSEQUENTIAL, INCIDENTAL
OR INDIRECT DAMAGES, INCLUDING,
BUT NOT LIMITED TO, LOSS OF
PROFITS, COST OF SUBSTITUTE
PRODUCTS AND PERSONAL
INJURY OR PROPERTY DAMAGE,
WHETHER SUCH CLAIM IS BASED
ON CONTRACT OR TORT OR ANY
OTHER THEORY OF LAW, AND
(B) FOXFURY’S ONLY DUTIES IN

CONNECTION WITH THE SALE
OF THIS PRODUCT SHALL BE TO
HONOR THE LIMITED WARRANTY
SET FORTH HEREIN. TO THE
EXTENT THAT THIS LIMITED
WARRANTY IS INCONSISTENT WITH
APPLICABLE LAW, THIS STATEMENT
SHALL BE DEEMED MODIFIED
TO BE CONSISTENT WITH SUCH
APPLICABLE LAW.

CONTACT FOXFURY

FoxFury, LLC

Oceanside, CA 92056 USA

Toll-Free: 844-FOXFURY

Tel : [phone]
Fax: [phone]

Email: [e-mail]

Web: FoxFury.com

All FoxFury products are designed in
Oceanside, CA. All FoxFury products
are manufactured with the highest
quality USA and foreign parts. Products
are assembled in either FoxFury’s
controlled plant in Asia or the USA,
under strict quality control.

WARRANTY AND OTHER
INFORMATION

PRODUCT DURABILITY

Meets NFPA 1971 Guidelines and can
sustain exposure to 500°F (260°C) for
30 minutes

CARE/CLEANING

Your FoxFury product is a professional
tool, but regular maintenance and care
of your light will maximize performance
for you. As needed, wash your FoxFury
product using a soft washcloth, clean
water and a mild soap. Be sure that the
flashlight’s Tailcap is SEALED before
washing. When done, pat dry with a
damp cloth.

AVAILABLE ACCESSORIES

SideSlide C-Clamp Adaptor
P/N 85-010

SideSlide Picatinny Adaptor
P/N 85-012

SideSlide Flashlight ONLY
P/N 940-012

SideSlide Picatinny Pressure
Switch Cap, P/N 50-150

WARNINGS

FoxFury, LLC is not responsible for the
incorrect use of any FoxFury Lighting
product.

Lights are strong enough to
cause damage to the human eye.

Do not stare into LEDs for long
periods of time or from a close
range (less than 2 ft).

FoxFury, LLC is not responsible
for any injury or damage caused
during the use of this product.

Usage of this product must be
supervised by an adult when it is
being used by a minor.

Any FoxFury product should
be operated at speeds safe
enough to maneuver around
surrounding obstacles.

Do not use under the influence
of drugs or alcohol.

LIMITED WARRANTY

FoxFury, LLC (“FoxFury”) warrants
to the purchaser of this product
(“Buyer”) that for a period of two
years following purchase, this product
will be free from defects in material
and workmanship and will function in
substantial compliance with FoxFury’s
written specifications for this product
as specified in the instruction manual
or on FoxFury’s website located at
www.FoxFury.com. Buyer’s exclusive
remedy shall, in any case, be limited,
at FoxFury’s election, to: A) repair or
replacement of the defective product;
or B) refund of the purchase price for
this product.

THE FOREGOING WARRANTY IS
THE ONLY WARRANTY MADE
BY FOXFURY WITH RESPECT TO
THIS PRODUCT. TO THE EXTENT
ALLOWED BY APPLICABLE LAW,
THERE ARE NO REPRESENTATIONS
OR WARRANTIES OF ANY KIND
BY THE FOXFURY, EXPRESS OR
IMPLIED, WITH RESPECT TO THE
CONDITION OR PERFORMANCE OF
THIS PRODUCT, INCLUDING, BUT
NOT LIMITED TO, MERCHANTABILITY
OR FITNESS FOR A PARTICULAR
PURPOSE.

IPX7

3 M

1 M

FOXFURY.COM

5/2017