Clip Hole
Battery
W Clip
Center
End Loop
Dimensions
4.8” (122mm) x 1.3” (33mm) x 1.0” (25mm)
Weight
8.9 oz (252g)
FULL POWER
8 hrs
RESERVE POWER
Up to 24 hrs
COMMAND STEALTH SERIES
420-307 Scuba
420-310 Mil-Tac
420-332 Tac IR Gen II/III+ Invisible
420-377 Scuba-Tac
Please read the below before using your Command Stealth headlamp as it
relays beneficial operating and safety information.
PHYSICAL CHARACTERISTICS:
- TPR housing
BATTERIES:
- The Command Series models require four (4) AA batteries at
(1.2 to 1.6 volts each).
- Acceptable battery types (run time will depend upon battery
quality and charge): Alkaline, Rechargeable, or 1.5v Lithium (Li-FeS2).
NOTE: Mixing of used and new, or different brand batteries is not recommended
as this could lead to leakage or explosion.
BATTERY INSTALLATION/REPLACEMENT
The following is valid for P/N 420-310 & 420-332:
1. Open all four (4) of the battery compartment tabs and install four (4) AA
batteries. NOTE: Respect the polarity when installing (the inside of the
battery pack indicates proper battery placement).
2. Reassemble the battery pack, and secure the 4 tabs (snap them completely
closed). NOTE: Make sure the battery pack is closed properly in order to
maintain the best possible water tight seal.
3. Test the light’s performance by activating the on/off slide switch located at
the top of the light.
The following is valid for P/N 420-307 and 420-377:
1. Unscrew the cap of the battery compartment.
2. Install four (4) AA batteries.
a. Respect the appropriate polarity when installing (the inside of the
3. Twist cap back on.
a. To get cap started, press against the battery pack in order to
4. Test the light’s performance by activating the on/off slide switch located at
the top of the light.
OPERATING INSTRUCTIONS
battery pack indicates proper battery placement; see diagram
below).
overcome the Dual-Gasket Seal’s friction. You will notice
increased friction as you tighten the cap. NOTE: The Dual-Gasket
is necessary to create a waterproof seal.
BATTERY LIFE
Battery Life* is expected as follows:
*Battery life may vary according to Mode Selected, Battery Quality, and
prevailing Ambient Conditions.
ON/OFF SLIDE SWITCH:
The Command Stealth Series Headlamps have a titanium content slide
switch located at the top of the light’s main body.
To operate, simply press your finger on the slide switch and slide it left or
right.
OPERATIONAL MODES:
All Command Stealth Series Models are ON/OFF Only.
STRAPS:
- Silicone, Head & Chin Strap ONLY: P/N 420-307 & 420-377
- Both Elastic & Silicone Straps: P/N 420-310 & 420-332
CABLE GUIDE/HELMET HOLD DOWN:
A black cable guide with Velcro (included and installed on strap) is best used
when wrapped around both the strap and cable, making the cable less likely
to be caught or snagged on any surrounding objects.
REMOTING YOUR BATTERY CASE AND SECURING THE “W” CLIP TO
YOUR BATTERY PACK: P/N 420-307 & 420-377 ONLY
Your battery case may be remoted off the Head strap. You may more easily
secure the battery case to a pocket, belt, strap, etc with the
use of a “W” Clip (included).
For installation of “W” Clip onto battery case:
1. Compress the “W” Clip by bending the end loops
toward each other.
2. Insert one end loop in each of the two clip holes of the
battery case.
3. The center bend of the W Clip must be on the outside of the curved
portion of the battery case as shown.
4. When the W Clip is inserted to its maximum depth, the end loops will
spring outward and clip in the proper position.
Case
Wearing your headlamp with the battery case remoted:
1. Uncoil the cable.
2. Undo Velcro on side of head strap, slide out battery case and
secure head strap back in place.
3. Affix your battery case to pocket, belt, etc.
4. Put on your Headlamp and adjust for comfort.
PRODUCT DURABILITY, ENVIRONMENTAL CONSTRAINTS &
CERTIFICATIONS:
-EMC
IPX-7
Foxfury Command Stealth Series Inst Manual 06 17
Page 1
P/N 420-307 and 420-377 ONLY:
-EMC
IPX-7
For all Command Stealth lights:
- Fire Resistant: meets requirements of NFPA 1971-8.6 (2013)
- Survives Temperature Extremes of 0°F (-18°C) to 300°F (149°C)
NOTE: The elastic strap is not Fire Resistant.
CARE/CLEANING:
Your FoxFury is a professional tool, but regular maintenance and care of your
headlamp will maximize performance for you. As needed, wash your FoxFury
using a soft washcloth, clean water and a mild soap. Be sure that battery pack is
sealed before washing. When done, pat dry with a damp cloth. Be sure to
reapply silicone based lubricant onto the o-ring or gasket of the battery pack
after cleaning. Be sure to reapply silicone based lubricant onto the o-ring or
gasket of the battery pack after cleaning.
CARE/CLEANING of P/N 420-307 and 420-377
After use in salt water, turn the light off and ensure that the battery pack is
securely closed. Immediately rinse thoroughly with fresh water and then pat the
unit dry.
BATTERY PACK MAINTENANCE:
DEALING WITH CORROSION FROM LEAKING BATTERIES
Battery leakage may cause “corrosion” to build in the battery pack contacts, causing light
not to function properly.
In case of presence of Corrosion in the battery pack contacts, please follow the suggested
steps listed below:
NOTE: Corrosion from leaking batteries is not covered by warranty.
AVAILABLE ACCESSORIES:
- Silicone Black Strap, P/N 600-027
- Silicone Glow Strap, P/N 600-026
- Elastic Strap, P/N 60-019
- Cable Guide, P/N 50-023
- Overhead Strap, P/N 600-002
WARNINGS:
IMPORTANT
FoxFury, LLC is not responsible for the incorrect use of any FoxFury Lighting product.
• Lights are strong enough to cause damage to the human eye.
• Do not stare into LEDs for long periods of time or from a close range (less than 2
• FoxFury, LLC is not responsible for any injury or damage caused during the use of
• Usage of this product must be supervised by an adult when it is being used by a
• Any FoxFury product should be operated at speeds safe enough to maneuver
• Do not use under the influence of drugs or alcohol.
Dual-Gasket Care:
• Use a silicone based lubricant grease around the Dual-Gasket seal on
the battery cap.
• Apply each time you replace the batteries and/or clean the light.
1. Mix 50% vinegar and 50% water.
2. Remove batteries from the battery pack.
3. Pour the combination into the battery pack and let soak for 5 minutes.
4. Remove fluid from inside the battery pack and dry it properly with a paper
towel, and a blow drier (make sure no liquid residue is left inside battery pack).
5. Replace your batteries and test the light’s function.
6. Repeat as needed.
feet).
this product.
minor.
around surrounding obstacles.
UV LIGHT
• The UV LED during operation radiates intense UV light.
• Do not look directly into the UV light during operation, even for a brief period.
This can be harmful to the eyes due to the intensity of the UV light.
• When viewing with the UV light, please use UV filtered glasses to avoid damage
by the UV light.
LIMITED WARRANTY
FoxFury Limited Warranty & Customer Care Information
FoxFury, LLC (“FoxFury”) warrants to the purchaser of this product (“Buyer”) that for a
period of two years following purchase, this product will be free from defects in
material and workmanship and will function in substantial compliance with FoxFury’s
written specifications for this product as specified in the instruction manual or on
FoxFury’s website located at www.foxfury.com. Buyer’s exclusive remedy shall, in any
case, be limited, at FoxFury’s election, to: A) repair or replacement of the defective
product; or B) refund of the purchase price for this product. THE FOREGOING
WARRANTY IS THE ONLY WARRANTY MADE BY FOXFURY WITH RESPECT TO THIS
PRODUCT. TO THE EXTENT ALLOWED BY APPLICABLE LAW, THERE ARE NO
REPRESENTATIONS OR WARRANTIES OF ANY KIND BY THE FOXFURY, EXPRESS OR
IMPLIED, WITH RESPECT TO THE CONDITION OR PERFORMANCE OF THIS PRODUCT,
INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. This limited warranty shall not apply if this product is not stored,
handled, installed or used in strict accordance with manufacturer’s
specifications and instruction manuals, or which has been subject to misuse,
alteration, negligence or accident.
1. The damaged part or product must be returned to FoxFury PRIOR TO any repair
or replacement. Shipping costs are the responsibility of the claimant.
2. You must obtain a return authorization (RMA) number from FoxFury prior to
returning products. FoxFury is not responsible for any damage incurred while in
transit.
3. Buyer will be required to show proof of purchase – No Exceptions.
4. Any modifications to light, cable or battery pack automatically voids all
warranties on this product.
All warranty inquiries should be directed to FoxFury’s Customer Service
Department to handle all warranty /repair related inquiries.
TO THE EXTENT ALLOWED BY APPLICABLE LAW: (A) IN NO EVENT, WHETHER
DUE TO BREACH OF WARRANTY HEREUNDER OR ANY OTHER CAUSE
WHATSOEVER, SHALL FOXFURY BE LIABLE FOR OR OBLIGATED IN ANY MANNER
TO PAY CONSEQUENTIAL, INCIDENTAL OR INDIRECT DAMAGES, INCLUDING,
BUT NOT LIMITED TO, LOSS OF PROFITS, COST OF SUBSTITUTE PRODUCTS AND
PERSONAL INJURY OR PROPERTY DAMAGE, WHETHER SUCH CLAIM IS BASED
ON CONTRACT OR TORT OR ANY OTHER THEORY OF LAW, AND (B) FOXFURY’S
ONLY DUTIES IN CONNECTION WITH THE SALE OF THIS PRODUCT SHALL BE TO
HONOR THE LIMITED WARRANTY SET FORTH HEREIN. TO THE EXTENT THAT
THIS LIMITED WARRANTY IS INCONSISTENT WITH APPLICABLE LAW, THIS
STATEMENT SHALL BE DEEMED MODIFIED TO BE CONSISTENT WITH SUCH
APPLICABLE LAW.
All FoxFury products are designed in Oceanside, CA. All FoxFury products are
manufactured with the highest quality USA and foreign parts. Products are assembled
in either FoxFury’s controlled plant in Asia or the USA, under strict quality control.
Avoid direct eye exposure to UV light.
Keep out of reach of children.
FoxFury, LLC
Oceanside, CA 92056 USA
Toll-Free: 844-FOXFURY
Tel: 760.945.4231
Fax: 760.433.3650
Email: service@foxfury.com
www.FoxFury.com
Foxfury Command Stealth Series Inst Manual 06 17
Page 2
Loading...