FourStar 11226112 Assembly Instructions Manual

BEFORE YOU BEGIN, PLEASE READ THE ASSEMBLY INSTRUCTIONS CAREFULLY.
FOLLOW THEM STEP BY STEP.

CAUTION:

1. ADULT SUPERVISION IS REQUIRED DUE TO SMALL PARTS. HANDLE WITH CARE
WHEN UNPACKING AND ASSEMBLING THE PRODUCT.

2. ASSEMBLE ON A SOFT SURFACES TO PREVENT DAMAGE TO THE PRODUCT FINISH.

3. MAKE SURE ALL PARTS ARE INCLUDED BEFORE ASSEMBLY.

ASSEMBLY TOOLS REQUIRED

Do you have any questions? Missing small parts or hardware? If you need assistance with the
assembly of your 4 CUBE ORGANIZER WITH 2 BINS please e-mail our Customer Service

Department at:

[e-mail] or call us at [phone],

(800)

639-3803

or visit www.fourstari.com

Please include the following information when contacting us:

• Where item was purchased

• Item, model, style or SKU number listed on instructions or box

• Part number, description of the part and quantity needed

This information will help us get the proper part to you faster.

MODEL: 11226112

4 CUBE

ORGANIZER

ASSEMBLY INSTRUCTIONS

PARTS LIST AND HARDWARE

NO HARDWARE LIST QTY

12 PCS

4 PCS

2 PCS

4 PCS

22 PCS

12 PCS

NO PARTS LIST QTY

SCREW

SHORT DOWEL

LONG DOWEL

NAIL LEG

POWER PIN

STICKER

A

B

C

D

E

1

2

3

4

5

6

2 PC

2 PC

1 PC

2 PC

1 PCS

SIDE PANEL

TOP & BOTTOM
PANEL

CENTER PANEL

CENTER SIDE
PANEL

BACK PANEL

SCREWDRIVER HAMMER

2

4

D

D

A

A

UNFINISHED

EDGE

FINISHED
EDGE

FINISHED
EDGE

FINISHED
EDGE

1

3

B

D

A

A

C

FINISHED EDGE

UNFINISHED SURFACE

1

D

B

A

A

C

B

D

FINISHED
EDGE

1

A

C

B

D

D

A

B

5

B

A

E

UNFINISHED

SURFACE

STEP 1.

1.1 INSTALL DOWEL (2) INTO PANEL PRE-DRILLED HOLES ON PANEL (D).

1.2 ATTACH NAIL LEG (4) INTO PANEL (A) USING HAMMER AS SHOWN.

STEP 2

2.1 ATTACH PANEL (B)(D)(C) USING SHORT DOWEL (2) AND LONG DOWEL (3), AS SHOWN.

2.2 ATTACH PANEL (A) TO ASSEMBLED UNIT WITH SCREW (1) USING SCREWDRIVER.

STEP 3

3.1 ATTACH PANEL (D) TO ASSEMBLED UNIT AS SHOWN.

3.2 FOLLOWED BY PANEL (B).

STEP 4.

4.1 INSERT SCREW (1) INTO PRE-DRILLED HOLES ON PANEL (B)
TIGHTEN USING SCREWDRIVER, AS SHOWN.

STEP 5.

5.1 ATTACH PANEL (E) TO ASSEMBLED UNIT.

5.2 TIGHTEN IT WITH POWER PIN (5) USING HAMMER, AS SHOWN.

STEP 6.

6.1 COVER THE SCREW WITH STICKER (6).

6.3 COMPLETE.

A

A

B

B

C

D

D

A

A

B

B

C

D

D

6

ANTES DE EMPEZAR, POR FAVOR LEER LAS INSTRUCCIONES DE ARMADO. SEGUIRLAS
PASO A PASO.

PRECAUCIÓN:

1. SUPERVISIÓN ADULTA SE REQUIERE POR PIEZAS PEQUEÑAS. TENGA CUIDADO AL
DESEMBALAJE Y MONTAJE DEL PRODUCTO.

2. ASSEMLE EN UNA SUPERFICIE SUAVE PARA EVITAR DAÑAR EL ACABADO DEL
PRODUCTO.

3. ASEGÚRESE DE QUE ESTÉN TODAS LAS PIEZAS ANTES DEL MONTAJE.

HERRAMIENTAS PARA EL MONTAJET

Do you have any questions? Missing small parts or hardware? If you need assistance with the
assembly of your 4 CUBE ORGANIZER WITH 2 BINS please e-mail our Customer Service

Department at:

[e-mail] or call us at [phone],

(800)

639-3803

or visit www.fourstari.com

Please include the following information when contacting us:

• Where item was purchased

• Item, model, style or SKU number listed on instructions or box

• Part number, description of the part and quantity needed

This information will help us get the proper part to you faster.

MODELO: 11226112

ORGANIZADOR EN

FORMA DE CUBO

ASSEMBLY INSTRUCTIONS

LISTA DE PIEZAS Y ACCESORIOS

NO HARDWARE LIST QTY

12 PCS

4 PCS

2 PCS

4 PCS

22 PCS

12 PCS

NO PARTS LIST QTY

TORNILLO

CLAVIJA CORTA

CLAVIJA LARGA

CLAVO CON PATA

CLAVO

ETIQUETA

A

B

C

D

E

1

2

3

4

5

6

2 PC

2 PC

1 PC

2 PC

1 PCS

PANEL LATERAL

PANEL SUPERIOR
E INFERIOR

PANEL CENTRAL

PANEL LATERAL
CENTRAL

PANEL POSTERIOR

DESTORNILLADOR MARTILLO

2

4

D

D

A

A

BORDE
SINTERMINAR

BORDE
ACABADO

BORDE
ACABADO

BORDE
ACABADO

PASO 1.

1.1 INSTALAR CLAVIJAS (2) EN LOS AGUJEROS PERFORADOS DEL PANEL (D).

1.2 ADJUNTE LA PATA CON CLAVO (4) EN EL PANEL (A) CON UN MARTILLO
COMO SE MUESTRA.

PASO 4.

4.1 INSERTE EL TORNILLO ( 1 ) EN LOS AGUJEROS PREVIAMENTE
PERFORADOS EN EL PANEL (B ) USANDO EL DESTORNILLADOR , COMO
SE MUESTRA .

PASO 5.

5.1 FIJE EL PANEL (E ) A LA UNIDAD ARMADA.

5.2 AJUSTE CON CLAVOS ( 5 ) CON UN MARTILLO , COMO SE MUESTRA.

PASO 6.

6.1 CUBRIR LOS TORNILLOS CON ETIQUETAS ( 6 ) .

6.3 COMPLETAR.

PASO 2

2.1 FIJE EL PANEL (B), (C) (D) Y (E) A LA UNIDAD ARMADA CON TORNILLO (1), COMO SE
MUESTRA.

2.2 FIJE EL PANEL (A) A LA UNIDAD ARMADA CON TORNILLO (1) USANDO
DESTORNILLADOR.

PASO 3

3.1 FIJE EL PANEL ( D ) A LA UNIDAD MONTADA COMO SE MUESTRA .

3.2 SEGUIDO DE PANEL ( B ) .

1

3

B

D

A

A

C

BORDE ACABADO

SUPERFICIE SIN TERMINAR

1

D

B

A

A

C

B

D

BORDE
ACABADO

1

A

C

B

D

D

A

B

5

B

A

E

SUPERFICIE SIN
TERMINAR

A

A

B

B

C

D

D

6

A

A

B

B

C

D

D