Four-Faith F2164, F2264, F2664, F2464 User Manual

F2X64 Series User

Manual

Document Version

Page

V2.0.0

Product Name：F2X64

Total:99

F2X64 Series User Manual

The user manual is suitable for the following model:

Model

Product Type

F2164

GPRS RTU

F2264

CDMA RTU

F2464

WCDMA RTU

F2664

EVDO RTU

F2764

TDD-LTE RTU

F2864

FDD-LTE RTU

F2A64

LTE RTU

Four-Faith Smart Power Technology Co., Ltd.

Add：Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen

Tel：[phone] Email:[e-mail]

Web:http://www.four-faith.hk

F2X64 User Manual

2

2/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Files Revised Record

Date

Version

Remark

Author

2012-11-20

V1.1

1. Delete setting by simple command of SMS

2. Delete and modify some parameter settings

Xingfa.lin
2012-12-25

V1.2

1. Modify acqisition interval

Xingfa.lin

2013-4-1

V1.2

Date input voltage

Lynn Zhu

2014-1-3

V1.3

1. Add the sms command to read input value

2. Add the sms command to control output

Xingfa.lin
2015-5-28

V1.4

1. Add ADC sample type description

ZXZ

2017-10-10

V2.0.0

1.Change of company address

LXP

F2X64 User Manual

3

3/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Copyright Notice

All contents in the files are protected by copyright law, and all copyrights are reserved by Xiamen

Four-Faith Communication Technology Co., Ltd. Without written permission, all commercial

use of the files from Four-Faith are forbidden, such as copy, distribute, reproduce the files, etc.,

but non-commercial purpose, downloaded or printed by individual (all files shall be not revised,

and the copyright and other proprietorship notice shall be reserved) are welcome.

Trademark Notice

Four-Faith 、 四信 、 、 、 are all registered trademarks of Xiamen

Four-Faith Communication Technology Co., Ltd., illegal use of the name of Four-Faith,

trademarks and other marks of Four-Faith is forbidden, unless written permission is authorized in

advance.

F2X64 User Manual

4

4/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Note: There may be different components and interfaces in different model,please in kind prevail.

F2X64 User Manual

5

5/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Contents

Contents...............................................................................................................................................5

Chapter 1 Brief Introduction of Product............................................................................................. 9

1.1 General.................................................................................................................................. 9

1.2 Features and Benefits............................................................................................................ 9

1.3 Working Principle................................................................................................................11

1.4 Specifications...................................................................................................................... 12

Chapter 2 Installation Introduction................................................................................................... 15

2.1 General................................................................................................................................ 15

2.2 Encasement List.................................................................................................................. 15

2.3 Installation and Cable Connection...................................................................................... 16

2.4 Power...................................................................................................................................21

2.5 Indicator Lights Introduction.............................................................................................. 21

Chapter 3 RTU Function Introduction........................................................................................... 22

3.1 Multiple servers funticon.................................................................................................... 22

3.2 MODBUS protocol............................................................................................................. 22

3.2.1 MODBUS settings................................................................................................... 23

3.2.2 TCP2COM description............................................................................................ 23

3.2.3 MODBUS digital IO input introduction..................................................................23

3.2.4 MODBUS digital IO output introduction................................................................24

3.2.5 MODBUS read digital IO output introduction........................................................25

3.2.6 MODBUS counter introduction...............................................................................26

3.2.7 MODBUS analog input introduction....................................................................... 27

3.3 RTU extended protocol....................................................................................................... 29

3.4 Alarm function.....................................................................................................................29

3.5 Multiply configure parameters............................................................................................29

3.6 Remote upgrade firmware...................................................................................................30

Chapter 4 Configuration....................................................................................................................30

4.1 RS232/RS485 Configuration.............................................................................................. 30

4.1.1 Configuration introduction.......................................................................................30

4.1.2 Run the configure tool..............................................................................................31

4.1.3 Re-power RTU......................................................................................................... 32

4.1.4 Configuration........................................................................................................... 33

4.1.4.1 Digital channel settings.................................................................................33

◆ Digital input function..................................................................................33

◆ MODBUS logic corresponding function....................................................34

◆ Acquisition purpose.................................................................................... 34

F2X64 User Manual

6

6/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

◆ Acquisition interval.....................................................................................34

◆ Alarm trigger condition...............................................................................35

◆ Alarm content.............................................................................................. 35

◆ Alarm phone number...................................................................................35

4.1.4.2 Optocoupler and relay settings..................................................................... 36

◆ Digital output function................................................................................36

◆ MODBUS logic 1 output............................................................................ 37

◆ MODBUS logic 0 output............................................................................ 37

◆ MODBUS logic 1 square-wave cycle.........................................................37

◆ MODBUS logic 0 square-wave cycle.........................................................38

◆ Default output voltage.................................................................................38

4.1.4.3 Analog channel settings................................................................................ 39

◆ Analog input function................................................................................. 39

◆ Set sensor range.......................................................................................... 39

◆ Set sensor voltage or current output........................................................... 41

◆ MODBUS function..................................................................................... 42

◆ Acqisition function...................................................................................... 42

◆ Acqisition interval....................................................................................... 42

◆ Alarm trigger condition...............................................................................43

◆ Alarm content.............................................................................................. 43

◆ Alarm phone number...................................................................................43

◆ Active report function................................................................................. 44

.4.1.4.4 RTU counter、report、Alarm settings.................................................... 45

◆ Counter function......................................................................................... 45

◆ Counter work mode.....................................................................................45

◆ Counter initial value....................................................................................46

◆ Alarm function............................................................................................ 46

◆ Alarm content.............................................................................................. 46

◆ Alarm phone number...................................................................................46

◆ Alarm upper limit........................................................................................47

◆ Active report interval.................................................................................. 47

◆ Alarm report method................................................................................... 48

◆ Continuous alarm interval...........................................................................48

◆ Continuous alarm number of times.............................................................48

◆ Alarm administrator number.......................................................................49

4.1.4.5 ModBus Setting............................................................................................ 49

◆ ModBus work mode....................................................................................50

◆ ModBus address..........................................................................................50

◆ RTU work mode..........................................................................................51

4.1.4.6 Data Service Center Settings........................................................................ 52

◆ Data Center Number................................................................................... 52

F2X64 User Manual

7

7/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

◆ Main Center Addr+Port:............................................................................. 53

◆ Backup Center Addr+Port:..........................................................................53

◆ Multi DSC Configuration........................................................................... 54

◆ Main and Backup Center DNS Server........................................................55

◆ Center 2~5 DNS Server.............................................................................. 55

4.1.4.7 Device Settings............................................................................................. 56

◆ Work Mode..................................................................................................56

◆ Trigger Type................................................................................................ 57

◆ Disconnect to Trigger mode........................................................................57

◆ Debug Level................................................................................................57

◆ Databit, Parity, Stopbit................................................................................58

◆ Communication Baudrate........................................................................... 58

◆ Auto Back To Main Server......................................................................... 59

◆ Device ID....................................................................................................59

◆ SIM Card No............................................................................................... 59

◆ Bytes Interval.............................................................................................. 60

◆ Custom Register String...............................................................................60

◆ Custom Heartbeat String.............................................................................60

◆ Reconnect setting........................................................................................ 61

◆ Transfer meanning...................................................................................... 61

4.1.4.8 Other Settings................................................................................................62

◆ Network.......................................................................................................62

◆ SMS Center.................................................................................................63

◆ Heartbeat Interval........................................................................................63

◆ Call Trigger Phone No................................................................................ 64

◆ SMS Trigger Password............................................................................... 64

◆ Data Trigger Password................................................................................ 64

◆ TCP MTU....................................................................................................65

◆ Multi Center Reconnect Interval................................................................ 65

◆ Set parameter of configure SMS.................................................................65

4.1.4.9 Scheduled Power ON/OFF Setting...............................................................66

◆ RTC(Real Time Clock) Time Setting......................................................... 67

◆ Power On/Off Setting................................................................................. 67

4.1.4.10 SMS Setting................................................................................................ 77

◆ Destination number..................................................................................... 77

◆ SMS Sending Format..................................................................................78

◆ Data upload Style........................................................................................78

4.1.4.11 Functions..................................................................................................... 79

◆ Show Configure.......................................................................................... 79

◆ Show Baudrate............................................................................................ 79

◆ Auto Detect................................................................................................. 79

F2X64 User Manual

8

8/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

◆ Version Display........................................................................................... 79

◆ Signal Value................................................................................................ 80

◆ Factory setting.............................................................................................80

◆ Clear Output................................................................................................80

◆ Save Output.................................................................................................80

◆ Browse.........................................................................................................80

◆ Save Configure............................................................................................80

◆ Load Configure........................................................................................... 81

4.1.5 Work State Switch....................................................................................................81

4.2 Setting by SMS................................................................................................................... 81

4.2.1 Setting by AT command of SMS............................................................................. 81

4.2.2 setting remote upgrade............................................................................................. 82

4.2.3 Read digital IO input................................................................................................82

4.2.4 Control digital IO output..........................................................................................83

4.2.5 Read analog input.....................................................................................................83

4.3 Setting for RTU extended protocol.....................................................................................83

Chapter 5 Software Manual.............................................................................................................. 84

5.1 TCP2COM manual..............................................................................................................84

5.1.1 Open software.......................................................................................................... 84

5.1.2 Install the driver....................................................................................................... 85

5.1.3 Add virtual serial port.............................................................................................. 86

5.1.4 Setting the server parameters................................................................................... 88

5.1.5 Server connection state............................................................................................ 89

5.1.6 Monitor.....................................................................................................................90

5.1.7 Not transmited data query........................................................................................90

5.1.8 Delete database data.................................................................................................91

5.1.9 Quit...........................................................................................................................92

5.2 RTU center service.............................................................................................................. 92

5.2.1 Open software.......................................................................................................... 92

5.2.2 Service setting.......................................................................................................... 93

5.2.3 Start equipment and connect....................................................................................94

5.2.4 View the acquisition data......................................................................................... 94

5.2.5 Send data to RS232/RS485......................................................................................95

5.2.6 Control optocoupler and relay................................................................................. 95

5.2.7 Alarm information....................................................................................................96

5.2.8 Center service information.......................................................................................96

5.2.9 Query data................................................................................................................ 96

5.2.10 Remote configure...................................................................................................97

5.2.11 Upgrade.................................................................................................................. 98

5.2.12 Reset device........................................................................................................... 99

Appendix......................................................................................................................................... 100

F2X64 User Manual

9

9/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Chapter 1 Brief Introduction of Product

1.1 General

F2x64 series is wireless remote terminal unit(abbreviation:RTU). RTU has many functions

(analog input、switch input、switch output、pulse counting and wireless data communication ect).

It adopts high-powered industrial 32 bits CPU and embedded real time operating system. It

supports RS232 and RS485 (or RS422) port that can conveniently and transparently connect one

device to a cellular network, allowing you to connect to your existing serial devices with only

basic configuration. It has low power consumption states in which the power consumption could

be 1ower than 1mA@12VDC. It has compatible digital I/O channel, ADC, input pulse counter and

pulse wave output function.

1.2 Features and Benefits

Design for Industrial Application

 High-powered industrial cellular module

 High-powered industrial 32 bits CPU

 Support low power consumption mode, including multi-sleep and trigger modes to reduce the

power dissipation farthest

 Embedded Real Time Clock(RTC) circuit which can realize timing online/offline function

 Housing: iron, providing IP30 protection.

 Power range: DC 5~35V

Stability and Reliability

 Support hardware and software WDT

 Support auto recovery mechanism, including online detect, auto redial when offline to make

it always online

 RS232/RS485/RS422 port: 15KV ESD protection

 SIM/UIM port: 15KV ESD protection

 Power port: reverse-voltage and overvoltage protection

 Antenna port: lightning protection(optional)

Standard and Convenient

F2X64 User Manual

10

10/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

 Adopt terminal block interface, convenient for industrial application

 Support standard RS232 and RS485(or RS422) port that can connect to serial devices directly

 TTL logic level RS232 interface can be customized

 Support intellectual mode, enter into communication state automatically when powered

 Provide management software for remote management

 Support several work modes

 Convenient configuration and maintenance interface

High-performance

 8 ch acquisition analog input（resolution：16bit）Input voltage（0-5V）,Input current（0-20mA）,

Sampling rate(1.365kSPS) ，Accuracy ±0.5% or better

 4 ch relay output（5A/30VDC,5A/250VAC）

 4 ch optocoupler isolation output,open collector to 30V,40mA max.load,power consumption

125mW

 8 ch Digital input（“0”：0-3.3V，“1”：5-24V）. Contains all the way count function

 2MB SPI FLASH

 Support dual data centers, one main and another as backup

 Support multiple data centers , it can support maximum 5 data centers

 Support multi-center multi-function(for example: one data center is MODBUS RTU protocol

function, another data center is RTU extended protocol function)

 Support multiple online trigger ways, including SMS, ring and data. Support link

disconnection when timeout

 Support dynamic domain name(DDNS) and IP access to the data center

 Support RS232/RS485 MODBUS RTU protocol

 Support TCP MODBUS RTU protocol using TCP2COM software that converts TCP to

virtual serial port

 Support 8 digital inputs and 8 analog input manual query and automatic report

 Support 4 optocoupler isolated output ports and 4 relay outputs controlled via MODBUS

RTU protocol

 Support pulse counter initiate value configurable, Its realtime value can be queried via

MODBUS RTU protocol

 Support RTU extended protocol.

 Acquisition data(8 analog inputs and 8 digital inputs) is reported periodically via RTU

extended RTU protocal.

 Support RTU extended protocol. Reporting mode can be selected. there are three reporting

mode, including Network only, SMS only and Main network SMS backup(it uses SMS. when

network connect fail)

 Support RTU extended protocol.When reporting acquisition data failure, acquisition data are

saved to 2M byte SPI FALSH

 Support RTU extended protocol. The data center can query acquisition data actively

 Support RTU extended protocol. It has counter function that the initial value of the timer is

set and the value of the timer is queried

F2X64 User Manual

11

11/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

 Support RTU extended protocol. It has the data center and RS232/RS485 transparent

transmission function

 Support RTU extended protocol. it has alarm function, alarm information is reported

automatically(alarm trigger conditions can be configured independently).

 Support RTU extended protocol. Can remotely reboot RTU

 Support RTU extended protocol. Can remotely configure the parameters

 Support RTU extended protocol. The remote upgrading parameters can be configured, RTU

support remote upgrade firmware.

 Alarm function: Alarm information are reported through RTU extended protocol , SMS, or

both SMS and RTU extended protocol

 When alarm information are reported through SMS, alarm number and alarm content of each

channel can be configured independently

 The remote upgrading parameters can be configured by SMS. RTU upgrade the firmware

immediately when it received the upgrade command.

 Built-in industrial clock, the acquisition time can be recorded through this clock

 Network is automatically connected, when device power on. Network is automatically

reconnected when network is offline.

 Scheduled turn on and turn off power function make the device work in low-power mode

1.3 Working Principle

The principle chart of the RTU is as following:

8ch digital

input

8 ch analog

input

4ch relay out

4ch isolated out

F2X64 User Manual

12

12/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Cellular

Module

MCU

Antenna

SIM/UIM

Interface

Indicator

Lights

SRAM&

FLASH

WDT Module

RTC Module

User Interface

RS232/RS485/RS422

Module

Power Module

1.4 Specifications

Cellular Specification

ITEM

CONTENT

F2164 GPRS RTU

Standard and Band

EGSM 900/GSM 1800MHz, GSM 850/900/1800/1900MHz(optional)

Compliant to GSM phase 2/2+

GPRS class 10, class 12(optional)

Bandwidth

85.6Kbps

TX power

GSM850/900: <33dBm

GSM1800/1900: <30dBm

RX sensitivity

<-107dBm

F2264 CDMA RTU

Standard and Band

CDMA2000 1xRTT 800MHz, 450MHz(optional)

Bandwidth

153.6Kbps

TX power

<30dBm

RX sensitivity

<-104dBm

F2464 WCDMA RTU

Standard and Band

UMTS/WCDMA/HSDPA/HSUPA/HSPA+ 850/1900/2100MHz, 850/900/1900/2100MHz(optional)

GSM 850/900/1800/1900MHz

GPRS/EDGE CLASS 12

Bandwidth

DC-HSPA+: Download speed 42Mbps, Upload speed 5.76Mbps

HSPA+: Download speed 21Mbps, Upload speed 5.76Mbps

HSDPA: Download speed 7.2Mbps, HSUPA: Upload speed 5.76Mbps

UMTS: 384Kbps

TX power

<24dBm

F2X64 User Manual

13

13/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

RX sensitivity

<-109dBm

F2664 EVDO RTU

Standard and Band

CDMA2000 1xEV-DO Rev A 800MHz, 800/1900MHz(optional), 450MHz(optional)

CDMA2000 1xEV-DO Rev B 800/1900MHz(optional)

CDMA2000 1xRTT, IS-95 A/B

Bandwidth

EVDO Rev. A: Download speed 3.1Mbps, Upload speed 1.8Mbps

EVDO Rev. B: Download speed 14.7Mbps, Upload speed 5.4Mbps (optional)

TX power

<23dBm

RX sensitivity

<-104dBm

F2764 TDD-LTE RTU

Standard and

Band

TD-LTE 2600/1900/2300MHz(Band 38/39/40), 800/1400/1800MHz(Band 27/61/62)(optional)

TD-SCDMA 2010/1900MHz(A/F frequency band, Band 34/39)

GSM /GPRS/EDGE 900/1800/1900MHz

Bandwidth

TD-LTE: Download speed 61Mbps, Upload speed 18Mbps

TD-HSPA+: Download speed 4.2Mbps, Upload speed 2.2Mbps

TD-HSPA: Download speed 2.2Mbps, Upload speed 2.2Mbps

TX power

<23dBm

RX sensitivity

<-97dBm

F2864 FDD-LTE RTU

Standard and Band

FDD-LTE 2600/2100/1800/900/800MHz, 700/1700/2100MHz(optional)

DC-HSPA+/HSPA+/HSDPA/HSUPA/UMTS 850/900/2100MHz, 800/850/1900/2100MHz(optional)

EDGE/GPRS/GSM 850/900/1800/1900MHz

GPRS CLASS 10

GPRS CLASS 12

Bandwidth

FDD-LTE: Download speed 100Mbps, Upload speed 50Mbps

DC-HSPA+: Download speed 42Mbps, Upload speed 5.76Mbps

HSPA+: Download speed 21Mbps, Upload speed 5.76Mbps

HSDPA: Download speed 7.2Mbps, HSUPA: Upload speed 5.76Mbps

UMTS: 384Kbps

TX power

<23dBm

RX sensitivity

<-97dBm

F2A64 LTE RTU

Standard and Band

FDD-LTE,TD-LTE,EVDO,WCDMA,TD-SCDMA,CDMA1X,GPRS/EDGE

Bandwidth

FDD-LTE: Download speed 100Mbps, Upload speed 50Mbps

TD-LTE: Download speed 61Mbps, Upload speed 18Mbps

DC-HSPA+: Download speed 42Mbps, Upload speed 5.76Mbps

TD-HSPA+: Download speed 4.2Mbps, Upload speed 2.2Mbps

EVDO Rev. A: Download speed 3.1Mbps, Upload speed 1.8Mbps

TX power

<23dBm

RX sensitivity

<-97dBm

F2X64 User Manual

14

14/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Hardware System

Item

Content

CPU

Industrial 32 bits CPU

FLASH

2MB（Extendable 8MB）

SRAM

512KB（Extendable 1MB）

Interface Type

Item

Content

Serial

1 RS232 port and 1 RS485port, 15KV ESD protection

Data bits: 5, 6 ,7, 8

Stop bits: 1, 1.5, 2

Parity: none, even, odd, space, mark

Baud rate: 110~230400 bps

Indicator

"Power", "ACT", "Online"

Antenna

Cellular: Standard SMA female interface, 50 ohm

lighting protection(optional)

SIM/UIM

Standard 3V/1.8V user card interface, 15KV ESD protection

Power

Terminal block interface, reverse-voltage and overvoltage protection

Power Input

Item

Content

Standard Power

DC 12V/0.5A

Power Range

DC 5~35V

Power Consumption

Working States

Power Consumption

Communication

88-100mA@12VDC

Standby

52mA@12VDC

Timing Power

Off

0.9mA@12VDC

F2X64 User Manual

15

15/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Physical Characteristics

Item

Content

Housing

Iron, providing IP30 protection

Dimensions

157x97x25 mm

Weight

500g

Environmental Limits

Item

Content

Operating

Temperature

-35~+75ºC（-31~+167℉）

Storage

Temperature

-40~+85ºC（-40~+185℉）

Operating

Humidity

95% ( Non-condensing)

Chapter 2 Installation Introduction

2.1 General

The RTU must be installed correctly to make it work properly.

Warning: Forbid to install the RTU when powered!

2.2 Encasement List

Name

Quantity

Remark

RTU host

1

Cellular Antenna

1

Power adapter

1

RS232 data cable

1

optional

RS485 data cable

1

optional

F2X64 User Manual

16

16/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Manual CD

1

Certification card

1

Maintenance card

1

Table 2-1 Encasement List

2.3 Installation and Cable Connection

Dimension: (unit: mm)

Figure 2-1 Installation Chart

Installation of SIM/UIM card:

Firstly power off the RTU, and press the out button of the SIM/UIM card outlet with a needle

object. Then the SIM/UIM card sheath will flick out at once. Put SIM/UIM card into the card

sheath (Pay attention to put the side which has metal point outside), and insert card sheath back to

the SIM/UIM card outlet.

Warning: Forbid to install SIM/UIM card when powered!

Installation of antenna:

Screw the SMA male pin of the antenna to the female SMA outlet of the RTU tightly.

Warning: The antenna must be screwed tightly, or the signal quality of antenna will be influenced!

User Interface Signal Definition

Pin

Number

Function

Interface

Default function

Function expansion

1

Power

PWR

Power input positive

None

2

GND

Power input negative

None

3

RS232

G/232

RS232 GND

None

F2X64 User Manual

17

17/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

4

RXD

RS232 Data receiving

None

5

TXD

RS232 Date sending

None

6

RS485

A

RS485 positive

Reserve compatible

RS232 DTR

7

B

RS485 negative

Reserve compatible

RS232 DSR

8

Digital

Input

DI1/C

Digital input1

Counting function

9

DI2

Digital input 2

None

10

DI3

Digital input 3

None

11

DI4

Digital input 4

None

12

DI5

Digital input 5

None

13

Digital

Input

DI6

Digital input 6

None

14

DI7

Digital input 7

None

15

DI8

Digital input 8

None

16

DIG

Digital input GND

None

18

Optocoupl

er output

DO1

Optocoupler output 1

None

19

DO2

Optocoupler output 2

None

20

DO3

Optocoupler output 3

None

21

DO4

Optocoupler output 4

None

22

COM

COM GND

None

23

Relay

output

K1-

Relay output 1-

None

24

K1+

Relay output 1+

None

25

K2-

Relay output 2-

None

26

K2+

Relay output 2+

None

27

K3-

Relay output 3-

None

28

K3+

Relay output 3+

None

29

K4-

Relay output 4-

None

30

K4+

Relay output 4+

None

31

ADC

A1

ADC 1

None

32

A2

ADC 2

None

33

A3

ADC 3

None

34

A4

ADC 4

None

35

A5

ADC 5

None

36

A6

ADC 6

None

37

A7

ADC 7

None

F2X64 User Manual

18

18/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

38

A8

ADC 8

None

39

AG

AGND

None

40

SW

V1

A1’s Sample type was Volt

I1

A1’s Sample type was Current

41

V2

A2’s Sample type was Volt

I2

A2 ’s Sample type was Current

42

V3

A3’s Sample type was Volt

I3

A3 ’s Sample type was Current

43

V4

A4’s Sample type was Volt

I4

A4 ’s Sample type was Current

44

V5

A5’s Sample type was Volt

I5

A5 ’s Sample type was Current

45

V6

A6’s Sample type was Volt

I6

A6 ’s Sample type was Current

46

V7

A7’s Sample type was Volt

I7

A7 ’s Sample type was Current

47

V8

A8’s Sample type was Volt

I8

A8 ’s Sample type was Current

Installation of cable:

F2X64 adopts industrial terminal block interface. The recommendatory cable is 28-16AWG.

The detail description of standard layout adapter and communication cables as is following:

Adapter（Rating Output 12VDC/0.5A）：

Cable Color

Power Output Polarity

Black &White Alternate

Anode

Black

Cathode

RS232 Cable：

Cable Color

Corresponding DB9-M Pin Number

Brown

Pin 2

Blue

Pin 3

Black

Pin 5

F2X64 User Manual

19

19/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

RS485 Cable：

Cable Color

Signal definition

Red

RS485(A)

Black

RS485(B)

Power adapter and communication cable connection chart as following:

Digital Input cable connection

F2X64 User Manual

20

20/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Wet contact Dry contact

Optocoupler output cable connection

Relay output cable connection

F2X64 User Manual

21

21/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

ADC cable connection

2.4 Power

The power range of the RTU is DC 5~35V

Warning: When we use other power, we should make sure that the power can supply power

above 4W.

We recommend user to use the standard DC 12V/0.5A power adaptor.

2.5 Indicator Lights Introduction

The RTU provides three indicator lights: “Power”, “ACT”, “Online”.

Indicator

Light

State

Introduction

Power

ON

RTU is powered on

OFF

RTU is powered off

ACT

BLINK

Data is communicating

OFF

No data

Online

ON

RTU has logged on network

OFF

RTU hasn’t logged on network

F2X64 User Manual

22

22/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Chapter 3 RTU Function Introduction

RTU is based on our ip modem which has realized data transparent transmission. It can collect

analog signal and digital signal. It also can output digital signal including 4 optocoupler isolated

outputs and 4 relay outputs. It has pulse counter. Main funcions as following:

1. Support dual data centers, one main and another backup, support multiple data centers

and it can support maximum 5 data centers, support multi-center multi-function(for

example: one data center works with MODBUS RTU protocol , another data center can

work with RTU extended protocol)

2. support multi online trigger ways, including SMS, ring and data. Support link

disconnection when timeout

3. Network is automatically connect,when device offline, it will automatically reconnect.

4. Support RS232/RS485 MODBUS RTU protocol, support TCP MODBUS RTU protocol

using TCP2COM software that converts TCP to virtual serial port.

5. Alarm function: Alarm information are reported through RTU extended protocol , SMS,

or both SMS and RTU extended protocol

6. Multiple configure methods.

7. Local and remote upgrade firmware.

8. Scheduled turn on and turn off power function make the device work in low-power mode

3.1 Multiple servers funticon

RTU support multi-center multi-function. Each center functions can be configured independently,

parameter settings please refer to appendix 4.1.4.6 Data Service Center Settings. Connection

protocol please refer to appendix 4.1.4.7 Work Mode.

3.2 MODBUS protocol

RTU support RS232/RS485 MODBUS RTU protocol. The principle of TCP MODBUS RTU

protocol is the same as RS232/RS485 MODBUS RTU protocol. TCP2COM softwave we

provided realize TCP to virtual serial port function(it can remotely transfer MODBUS RTU

protocol). The following introduces MODBUS RTU protocol, All of the following MODBUS data

are high byte first (big-endian mode).

F2X64 User Manual

23

23/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

3.2.1 MODBUS settings

Enable MODBUS function, related settings please refer to appendix 4.1.4.5 ModBus Setting, it

also need to configure the digital input, digital output, analog input and counter input

independently.

3.2.2 TCP2COM description

TCP2COM softwave realize TCP to virtual serial port function. The principle of TCP MODBUS

RTU protocol is the same as RS232/RS485 MODBUS RTU protocol. About using TCP2COM

softwave, please refer to appendix 5.1 TCP2COM Manual.

3.2.3 MODBUS digital IO input introduction

The MODBUS function code of digital IO input is 0x02(read input status), the starting register

address is 0, there are total 8 digital input(register address from 0 to 7). The MODBUS settings of

digital IO input please refer to appendix 4.1.4.1 Digital input function.

Eg:

Query all digital input ports (all 8 input ports), command as following:

01 02 00 00 00 08 79 CC

Parse command:

Byte-

orders

1234567

8

Content

01020000000879

CC

Parsing

Slave

Address

Function

code

Start address

number of registers

Checksum

Meanin

g

01

Read

input

status

Address is 0-7

corresponding to

IO1-IO8
seperately。

Read the value of

digital IO input.

This example read

8 ports . If read one

channel, this

parameter should

be 0001

checksum

Response

01 02 01 00 A1 88

Parse response:

F2X64 User Manual

24

24/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Byte-

orders

12345

6

Content

01020100A1

88

Parsing

Slave

Address

Function

code

Data length

IO status value

Checksum

Meaning

01

Read input

statuss

Data length

IO status value,

bit0~bit7

corresponding to

IO1-IO8

checksum

3.2.4 MODBUS digital IO output introduction

The MODBUS function code of digital IO output is 0x05, the starting address is 0, there are total

8 output ports(address 0-3 used for optocouplers output ports, corresponding to optocouplers port

1-4, address 4-7 used for relay outputs,corresponding to rlay output 1-4). The MODBUS

configuration of digital IO output please refer to appendix 4.1.4.2 Optocoupler and relay settings.

Eg:

Control one digital IO output, command as following:

01 05 00 00 FF 00 8C 3A

Parse command:

Byte-

orders

1234567

8

Content

01050000FF008C

3A

Parsing

Slave

Address

Functio

n code

Start address

Output value：FF00
means logic 1 ，

0000

means logic 0.

checksum

Meanin

g

01

Force

single

coil

Address is 0-3 used

for optocouplers

output, address 4-7

used for relay

outputs

The digital output

value.

checksum

Response

01 05 00 00 FF 00 8C 3A

Parse response:

The response command is the same as sending command, please refer to appendix the above

control command.

F2X64 User Manual

25

25/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

3.2.5 MODBUS read digital IO output introduction

The MODBUS function code of readding digital IO output is 0x01, the starting address is 0, there

are total 8 output ports(address 0-3 used for optocouplers output ports, corresponding to

optocouplers port 1-4, address 4-7 used for relay outputs,corresponding to rlay output 1-4). The

MODBUS configuration of readding digital IO output please refer to appendix 4.1.4.2

Optocoupler and relay settings.

Eg:

Read all digital IO output, command as following:

01 01 00 00 00 08 3D CC

Parse command:

Byte-

orders

1234567

8

Content

0101000000083D

CC

Parsing

Slave

Address

Functio

n code

Start address

Coil number

checksum

Meanin

g

01

Force

single

coil

Address is 0-3 used

for optocouplers

output, address 4-7

used for relay

outputs

The digital output

value.

checksum

Response:

01 01 01 55 91 B7
Parse response：

Byte-

orders

12345

6

Content

0101015591

B7

Parsing

Slave

Address

Function

code

Data length

IO status

value

checksum

Meaning

01

Read coil

Bytes count

IO status

value,

bit0~bit7

correspondi

ng to

IO1-IO8

checksum

F2X64 User Manual

26

26/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

3.2.6 MODBUS counter introduction

The counter input port and the first channel of digital IO input is the same pin.

The MODBUS function code of reading counter value is 0x03(read holding register), the starting

address is 0. The MODBUS function code of setting counter initial value is 0x10(preset multiple

registers), the starting address is 0. The MODBUS parameters of counter please refer to appendix

4.1.4.4 RTU counter settings.

Eg:

Read counter value, command as following:

01 03 00 00 00 02 C4 0B

Parse command:

Byte-

orders

1234567

8

Content

010300000002C4

0B

Parsing

Slave

address

Functio

n code

Start address

number of

Registers

checksum

Meanin

g

01

Read

holding

register

Address 0

corresponding to

counter

Counter value is a

32 bit value,so,

need to read two 16

bit regiesters

checksum

Response

01 03 04 00 00 00 00 FA 33

Parse response:

Byte-

orders

123456789

Conten

t

01030400000000FA33

Parsing

Slave

address

Functi

on

code

Data

length

Data 1

Data 2

Checksum

Meani

ng

01

Read

holdin

g

register

Data

length

Counter value is

32 bits

Corresponding to

high 16 bits

Counter value is

32 bits

Corresponding to

low 16 bits

Checksum

Set counter initial value, command as following:

01 10 00 00 00 02 04 00 00 00 0A 73 A8

Parse command:

F2X64 User Manual

27

27/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Byte-

orders

123456789

Conten

t

011000000002040000

Parsing

Slave

address

Functi

on

code

Start address

Number of

Registers

c

High 16 bits

value

Meani

ng

01

Preset

multipl

e

register

s

Address 0

corresponding to

counter

Counter value is

32 bits, so need

to write two 16

bits registers

Byte

count

Correspond to

high 16 bits of

counter value

Contiune

101112

13

000A73

A8

Low 16 bits value

Checksum

Correspond to low 16 bits of counter value

checksum

Response

01 10 00 00 00 02 41 C8

Parse response:

Byte-

orders

1234567

8

Content

01100000000241

C8

Parsing

Slave

Address

Functio

n code

Start address

number of registers

Checksum

Meanin

g

01

Preset

multiple

registers

Address 0

corresponding to

counter

Counter value is 32

bits, so need to

operate two 16 bits

registers

checksum

3.2.7 MODBUS analog input introduction

The MODBUS function code of analog input is 0x04(read input register), the starting address is 0,

there are total 8 channels (the value of each channel is a signed 32-bit data, this data is the actual

value of the sensor). The MODBUS parameters of analog input please refer to appendix 4.1.4.3

Analog input function.

F2X64 User Manual

28

28/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

Query all channels(all 8 channels) of analog input, command as following:

01 04 00 00 00 10 F1 C6

Parse command:

Byte-

orders

1234567

8

Content

010400000010F1

C6

Parsing

Slave

Address

Functio

n code

Start Address

number of registers

Checksum

Meanin

g

01

Read

input

register

Address 0000-0010

correspond to

AIN1-AIN8

Analog input value

is 32 bits, high 16

bits first. If read

one channel, this

parameter should

be 0002

checksum

Response

01 04 20 00 00 01 82 00 00 00 0C 00 00 00 0C 00 00 00 0C 00 00 00 0C 00 00 00 0C 00 00 00 0C

00 00 00 0C B0 A2

Parse response:

Byte-

orders

1234567

Content

01042000000182

Parsing

Slave

address

Function

code

Data

length

Data 1

Data 2

Meaning

01

Read

input

register

Byte

count

Corresponding to high

16 bits of first channel

value. Te value of each

channel is a signed

32-bit data

Corresponding to low

16 bits of first channel

value. Te value of each

channel is a signed

32-bit data

continue

891011…323334353637

0000000C…0000000CB0A2

Data 3

Data 4

…

Data 15

Data 16

Checksum

Corresponding

to high 16 bits

of second

channel value.

Te value of

each channel is

Corresponding

to low 16 bits

of second

channel value.

Te value of

each channel is

…

corresponding

to high 16 bits

of eighth

channel value.

Te value of

each channel is

corresponding

to low 16 bits

of eighth

channel value.

Te value of

each channel is

checksum

F2X64 User Manual

29

29/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

a signed 32-bit

data

a signed 32-bit

data

a signed 32-bit

data

a signed 32-bit

data

3.3 RTU extended protocol

RTU extended protocol has the following main functions:

1. Acquisition data(including analog input and digital input) are reported periodically.

2. Reporting mode can be selected. there are three reporting modes, including Network only,

SMS only and Main network ,SMS as backup(it uses SMS. when network connection fail)

3. When reporting acquisition data failure, acquisition data are saved to 2M byte SPI

nonvolatile flash which is saved forever even if the device powered off.

4. The data center can query acquisition data actively

5. It has counter function that the initial value of the counter can be configured, its realtime

value can be queried

6. It provede the transparent transmission tunnel between the data center and the terminal

devices which connected to the RTU RS232/485 port. This function works same as our

company’s ip modem.

7. It has alarm function and the alarm information can be reported periodically(alarm trigger

conditions can be configured independently).

8. It can be controlled to reboot from the remote side.

9. support remote configure the parameters

10. Local and remote upgrade the firmware.

Please refer to appendix 5.2 RTU center service.

3.4 Alarm function

Alarm informations can be reported through RTU extended protocol only, SMS only and both

SMS and RTU extended protocol. When alarm informations are reported through SMS, alarm

phone number and alarm content of each channel can be configured independently. detail

description please refer to appendix 5.2.7 Alarm information.

3.5 Multiply configure parameters

All the RTU parameters can be configured through RS232/RS485 、 SMS and RTU extended

protocol. Please refer to appendix chapter 4 configuration.

F2X64 User Manual

30

30/103

Email: [e-mail] Tel: [phone] Web: www.four-faith.hk

Add: Floor 11, Area A06, No 370, chengyi street, Jimei, Xiamen, China

3.6 Remote upgrade firmware

RTU can remote upgrade firmware through TCP or UDP. First put new firmware (the version

should higher than the current software version) on RTU center software(its manual refer to 5.2

RTU center service) installation directory. then, configure upgraded parameters, these parameters

can be configured by SMS or RTU extended protocol. When RTU received the valid upgrade

parameters, it will upgrade the firmware automatically. Detail settings please refer to appendix

4.2.2.2 Overall setting by SMS or 5.10 Remote configure.

Chapter 4 Configuration

All the RTU settings can be configured through RS232/RS485、SMS and RTU extended protocol.

4.1 RS232/RS485 Configuration

Before configuration, It’s necessary to connect the RTU with the configure PC by the shipped

RS232 or RS232-485 cable as following.

4.1.1 Configuration introduction

There are two ways to configure the RTU: