Foshan Taobei Technology QN-M801 User Manual
Narcissus Electric Knife Sharpener
User Manual
Narci
ss
u
s
Please read this manual in detail before the first use.
Instructions for Sharpen Knives
1. Put the sharpener in a stable position, clean the knife and dry it.
2. Power on the sharpener and turn on the switch on the left.
Switch
Power Cable
3. Follow the steps below to sharpen the knife:
①Put the knife into the sharpening groove to make the blade
touches the rotating grinding wheel.
②Pull back slowly until the blade all pass
through the grinding wheel.
③Repeat steps ①② for 3 times.
④Change the knife to the neighboring sharpening groove.
⑤Repeat steps ①②③ to sharpen another side of the blade.
⑥Repeat steps ①②③④⑤ until the knife becomes sharp enough.
Tips
1. The sharpener has 2 different grinding wheels. The left wheel
is rough, suitable for grinding blunt knives. The right wheel
is smooth and suitable for grinding sharp knives.
Na
r
c
i
s
s
u
Crude
Rough wheel for
grinding blunt knives.
2. Each sharpening groove has two sides. Place the knife obliquely
against the inclined side to get a better sharpening effect.
s
Smooth wheel for
grinding sharp knives.
Pull Back
Fine
3. Turn on the sharpener first. Then put knives into the sharpening
groove to avoid damage to knives.
4. DO NOT push knives forward when sharpening to avoid
damage to knives.
5. DO NOT press down hard on knives when sharpening to avoid
damage to knives.
Push Forward
Press Down Hard
6. The sharpener is not suitable for grinding curved, thick, zigzag
kinves.
7. The sharpener CANNOT work continuously for more than 5
minutes for its overheat-protection device. Please wait patiently
for 15 minutes before resuming use it.
8. The sharpener sometimes sends a smell, this is normal, please
rest assured to use.
Grinding Scissors
①Move one blade of the scissors
slowly to touch the rotating
scissors grinding wheel.
②Pull the scissors against the
grinding wheel slowly.
③Repeat steps ①② for 3 times.
④Follow steps ①②③ to grind
another blade of the scissors.
⑤Repeat steps ①②③④ until the scissors are sharp enough.
Tips:The sharpener cannot fully repair the scissors with unstable
rivets. Because it can do nothing about the loose rivets.
Na
r
ci
ss
us
Grinding Slotted Screwdriver
①Insert the screwdriver into the
grinding hole slowly until it
touches the rotating grinding wheel.
②Push the screwdriver inward slowly
until its front end becomes
smooth enough.
Tips:
1. The sharpener CANNOT be used to grind Phillips screwdrivers.
2. DO NOT force the screwdriver inwards to avoid damage to
the sharpener.
N
arc
is
su
s
Precautions
1. Use the sharpener with the specific voltage 120V~60Hz.
2. Remove the grease and water from knives before sharpening.
3. DO NOT add water, oil or other substances when sharpening
knives to avoid danger.
4. The sharpener is not suitable for grinding curved, thick,
zigzag tools.
5. DO NOT allow water to flow into the sharpener to avoid damage.
6. In case the grinding wheel is stopped by knives, remove knives
immediately to avoid damage to the sharpener
7. Avoid using or touching by children to avoid accidents.
8. The sharpener must be placed in a dry area and away from
high temperatures.
9. Do not replace the wire without authorization. Unplug the wire
immediately if there is any problem, and contact Narcissus.
Replace the Grinding Wheels
Each wheel can grind about 100 knives. If the surface of the
wheel is serious, we recommend that you replace the wheel
in the following steps:
1. Unplug the power supply of the sharpener. Put the bottom up
on the table.
2. Remove the 4 foot pads at the bottom. Unscrew the 4 screws
in the foot pad holes.
3. Open the shell and use two wrenches to loosen the nuts on
both ends of the shaft.
4. Remove the old grinding wheel and replace it with a new one.
Be careful not to lose small parts.
5. Check that all components are installed correctly, and then
install nuts on both ends of the shaft.
6. Install the plastic cover, screws and foot pads in order.
7. Enjoy your new sharpener!
Cleaning and Maintenance
1. Clean up debris after each use to avoid damage to the sharpener.
Attention: Unplug the power plug before cleaning.
2. Unplug before cleaning.
3. Wipe the surface with a clean soft cloth.
4. DO NOT immerse the sharpener in water for cleaning.
5. Store the sharpener in a dry and ventilated place.
Warranty
Thanks for selecting and supporting Narcissus.
Narcissus provides all customers free 12 months of productreplacement services.
If there is any quality problem, please send emails to
support@narcissus.tech to contact us. We will provide you with
a satisfying solution.
Thank you for understanding!
Specification
Model: QN-M801
Rated Voltage: 120V~60Hz
Rated Power: 90W
Gross Weight: 2.67 lbs
Package Size: 9.8*4.8*4.7 in
Official Email: support@narcissus.tech
Manufacturer: Foshan Taobei Technology Co., Ltd.
Address: No.1 Guizhou Avenue West, Foshan, Guangdong, China
Loading...