Forza FDC-1502R, FDC-3002R User Manual

Download

Page 1

Year

warranty

Page 2

Table of contents

1. Introduction

1-1. Transportation 1-2. Preliminary steps 1-3. Initial setup 1-4. Important safety instructions 1-5. Maintenance, service and faults

2. Operation

2.1 Unpacking and inspection

2.2 UPS front and rear panel views

2.3 Installation procedure

2.4 UPS connections

2.5 Turning on the UPS

2.6 Battery replacement

2.7 ForzaTracker monitoring software

3. Advanced operation

3.1 Button and function description

3.2 LCD panel

3.3 Audible alarm

3.4 Abbreviations on the LCD display

3.5 UPS parameter settings

3.6 Operation mode description

3.7 Fault codes

3.8 Warning indicators

4. Troubleshooting

5. Storage and maintenance

6. Technical speciﬁcations

1. Introduction

Thank you for purchasing the Forza FDC-1502R and FDC -3002R Online UPS. To enjoy all the features and beneﬁts of this unit, please read and follow all installation and operation instructions thoroughly before unpacking, installing or operating this device. After you have read this manual, keep it in a safe place for future reference. The information contained in this manual covers the 1500VA and 3000VA uninterruptible power system, its basic functions, operating procedures, options available and troubleshooting guide. It also includes information on how to ship, store, handle, and install the equipment.

1-1. Transportation

• Make sure to transport the UPS system only in the original package to protect it against shock and impact.

1-2. Preliminary steps

• Water condensation may occur if the UPS is unpacked in a very cold environment and then moved to a warmer location.

• The UPS must be thoroughly dry before being installed. Failure to do so may increase the risk of electric shock.

• Do not install the UPS system near water or in moist environments.

• Do not install the UPS system where it would be exposed to direct sunlight or near a heater or heating vent.

• Do not block ventilation holes in the UPS housing.

1-3. Initial setup

Do not connect appliances or equipment that may overload the UPS system (such as a laser printer) to the output sockets. Place cables in such a way that no one can step on or trip over them. Do not connect domestic appliances, such as hair dryers, to the UPS output sockets. Connect the UPS system only to an earthed shockproof outlet which must be easily accessible and close to the UPS system. Use only CE-marked mains cable (e.g. the mains cable of your computer) to connect the UPS system to the building wiring outlet (shockproof outlet). Use only CE-marked power cables to connect the loads to the UPS system. During the installation of this equipment, make sure that the sum of the leakage currents of the UPS and the connected loads shall not exceed 3.5 mA.

CAUTION: The unit is heavy. Lifting the unit requires a minimum of two people.

•

1-4. Important safety instructions

Do not disconnect the mains cable on the UPS system or the building wiring outlet (shockproof socket outlet) at any time, since this would cancel the protective earth of the UPS system and of all connected loads. Connect the UPS only to a grounded socket that meets electrical safety guidelines. Locate the UPS near a wall socket. Do not use an extension cord between the UPS and the socket. In the event of an emergency, press the OFF/Enter button and disconnect the power cord from the AC mains to properly disable the UPS. Do not allow any kind of liquid or foreign object to enter this UPS unit. Do not place beverages or any other containers with liquid on or nearby the unit. The UPS can be operated by any individual with no previous experience.

•

Page 3

1-5. Maintenance, service and faults

The voltage used by this UPS may be hazardous. The unit contains no user serviceable parts; do not attempt to disassemble the unit. Only qualiﬁed service technicians can perform maintenance on the unit. Failure to adhere to this could cause personal injury or equipment malfunction and void the warranty. Caution: - risk of electric shock. Even after the unit is disconnected from the mains, components inside the UPS system are still connected to the battery packs which are potentially dangerous. Before carrying out any kind of service and/or maintenance, disconnect the batteries and verify that no current is present and no hazardous voltage exists in the terminals of high capacity capacitors, such as BUS-capacitors. Servicing of batteries should be performed or supervised by experts who possess the knowledge to closely follow all required precautions. To avoid electrical shock, turn off the unit and unplug it form the AC power source before servicing the battery. Caution: potentially hazardous voltages from the battery can still be present even after disconnecting the UPS from the AC mains. Therefore, the positive and negative terminals of the battery shall de disconnected prior to performing any maintenance or repair inside the unit. A battery can present the risk of short-circuit current and electrical shock. The following precautions should be taken:

- Remove wristwatches, rings and other metal objects

- Use only tools with insulated grips and handles.

- Wear rubber gloves and boots.

- Do not lay tools or metal parts on top of batteries.

- Disconnect charging source prior to connecting or disconnecting battery terminals.

- Determine if battery is inadvertently grounded. If inadvertently grounded, remove source from ground. Contact with any part of a grounded battery can result in electrical shock. The likelihood of such shock can be reduced if such grounds are removed during installation and maintenance. When replacing the battery, make sure to use the same type and number of sealed lead-acid batteries speciﬁed. We recommend using the Forza FUB-1290, a 12V 9A cell. Do not dispose of batteries in a ﬁre. Batteries may explode if exposed to high temperatures. Never try to open a battery. The cell contains a toxic electrolyte which is harmful to the skin and eyes. Replace the fuse only with the same type and amperage in order to avoid ﬁre hazards. Do not dismantle the UPS system.

•

2. OPERATION

2-1. Unpacking and inspection

2-2. UPS diagram

Front view

• One UPS unit

• One user manual

• One monitoring software CD (ForzaTracker)

• One USB cable

• Rack mounting hardware

• Tower support base

• Warranty certiﬁcate

Carefully inspect the UPS to check for any damages that may have occurred during shipping. Should any evidence of damage be found or if some parts are missing, do not turn the UPS on; you must immediately notify the carrier or dealer where you purchased the unit.

Remove the UPS from its package and make sure that all the following items are included:

2.3. Installation procedure

Choose location

Rear view

Cooling fan(s) Emergency Power off connector Battery bank terminal RS-232 communication port USB communication port SNMP intelligent slot Dedicated outlets for critical loads Programmable outlets for non-critical loads AC input Input circuit breaker Output circuit breakers Modem/Phone/Network surge protection

10.

11.

12.

FDC-1502R FDC-3002R

Install the UPS unit in any protected environment that provides adequate airﬂow around the unit, and free from excessive dust, corrosive fumes and conductive contaminants. Do not operate your UPS in an environment where the ambient temperature or humidity is high. For best performance, keep the indoor temperature between 0° C and 40° C. Place the UPS unit at least 20 cm away from monitors to avoid interference.

Page 4

2.3.1 Initial setup

• For safety considerations, the UPS is shipped out from the factory with battery wires disconnected.

• Before installing the UPS, the user must ﬁrst reconnect the wires. To do so, follow the steps illustrated below.

2-4. UPS connections

2-4.1 UPS input connection

• Plug the UPS into a two-pole, three-wire, grounded receptacle only.

• Avoid using extension cords or adapter plugs.

• Connect a single line modem/phone/fax cable into the network surge-protection “IN” jack on the rear panel of the UPS.

• Connect a network cable from the OUT jack on the rear of the UPS to a port on a PC or network device such as a router.

2-4.2 UPS output connection

2.4.3 Disabling and enabling the EPO function

For socket-type outputs, there are two kinds of outputs: programmable outlets and general outlets. Connect non-critical devices to the programmable outlets and critical devices to the general outlets. During power failure, you may extend the backup time to critical devices by setting shorter backup times for non-critical devices.

To allow for unattended UPS shutdown/start-up and status monitoring, connect one end of the communication cable to the USB/RS-232 port, and the other end to the communication port of your PC. With the monitoring software installed, you can schedule UPS shutdown/start-up and monitor its status through a PC.

The UPS is equipped with an intelligent slot perfect for either SNMP or AS400 card. When installing either SNMP or AS400 card in the UPS, it will provide advanced communication and monitoring options.

Note: The USB port and RS-232 port cannot be used at the same time.

CAUTION: For 1.5K model, to reduce the risk of ﬁre, connect only to a circuit provided with 20 amperes maximum

branch circuit overcurrent protection in accordance with the National Electric Code, ANSI/NFPA 70. CAUTION: For 3K model, to reduce the risk of ﬁre, connect only to a circuit provided with 30 amperes maximum branch circuit overcurrent protection in accordance with the National Electric Code, ANSI/NFPA 70.

Rack-mount installation

The unit comes with mounting brackets for the standard 19-inch (46.5cm) rack.

CAUTION: Do NOT use the mounting brackets to lift the unit. The mounting brackets are only for securing the unit to the rack.

This UPS can be either placed on a desktop, mounted in a rack or installed in an upright position. Deﬁne the proper display orientation based on the conﬁguration chosen to install this UPS.

Step 1

Remove the front panel.

Step 1

Tower installation

Allows the user to install the UPS in the upright position.

Step 2

Connect the AC input and then reconnect battery wires.

Step 3

Replace the front panel.

Step 1

Unfold and align the tower support base.

Step 2

Place the UPS vertically on the base.

Step 3

Verify that the UPS is stable and ﬁrmly attached to the base.

•

Connect the network surge protection

Network/Fax/Phone port

The UPS has two network cable RJ45 connectors for network lines.

Keep pins 1 and 2 closed for UPS normal operation. To activate the EPO feature, remove the wire between pin 1 and 2.

Communication ports

USB port RS-232 port Intelligent slot

IN OUT

Closed for UPS normal operation

Page 5

Use the supplied CD or go to the website: http://www.forzaups.com/us/driver-downloads/. After clicking the software icon, choose the required operation system. Follow the on-screen instructions to install the software. When you ﬁnished downloading all required ﬁles, enter the serial No (installation password): 5242-87f6-64re-di8d-986u to install the software (include the hyphens). In order to access as Administrator, input the password: 111296. When your computer restarts, the management software will appear as a light blue round icon located in the system tray, near the clock. Note: For Mac and Linux users, please refer to the ForzaTracker user guide found in our website.

Step 1

Remove the front panel of the UPS.

Step 2

Disconnect the battery wires.

Step 3

Remove the two screws and proceed to pull out the battery compartment.

Step 4

Remove the top cover of the compartment and replace the batteries.

Step 5

When done, replace the cover of the battery compartment and screw it to the unit chassis.

Step 6

Reconnect the battery wires.

Step 7

Replace the front panel of the UPS.

2.5 Turning on the UPS

Press the ON/Mute button on the front panel for two seconds to power on the UPS. Note: The battery charges fully during the ﬁrst ﬁve hours of normal operation. Do not expect full battery run capability during this initial

charge period.

2-7 ForzaTracker monitoring software

ForzaTracker is a new generation of UPS monitoring software, which provides user-friendly interface to monitor and control your UPS system. This unique software provides safe auto-shutdown for multi-computer systems during power failures. With this software, users can monitor and control any UPS on the same LAN no matter how far they might be from the UPS.

2.6 Battery replacement (Service personnel only)

NOTICE: This UPS is equipped with internal batteries and only qualiﬁed service personnel shall be allowed to replace the batteries.

Note: Once the batteries are removed, the connected equipment is no longer protected from power outages. CAUTION!! Make sure to follow all safety precautions and warnings during the replacement procedure.

3. Advanced operation

3-1. Description of buttons and functions

ON/MUTE SELECT OFF/ENTER

ON/Mute button

OFF/Enter button

Select button

Turn on the UPS: Press and hold the ON/Mute button for at least 2 seconds to turn on the UPS. Mute the alarm: When the UPS is on battery mode, press and hold this button for at least 3 seconds to disable or enable the alarm system. This command would not apply when warnings or errors occur. Up key: Press this button to display previous selection in the UPS configuration menu. Switch to UPS self-test mode: Press and hold ON/Mute button for 3 seconds to perform the self-test in AC mode, ECO mode, or converter mode.

Turn off the UPS: Press and hold this button for at least 2 seconds to turn off the UPS in battery mode. The UPS will remain in standby mode under normal power conditions or transfer to Bypass mode provided it has been enabled previously by pressing this button. Confirm selection key: Press this button to confirm the selection in the UPS configuration menu.

Switch LCD message: Press this button to change the LCD message for input voltage, input frequency, battery voltage, output voltage and output frequency. Setting mode: Press and hold this button for 3 seconds to enter the UPS configuration menu while UPS is in standby or bypass mode. Down key: Press this button to display the next selection in the UPS configuration menu.

Button Function

Installation procedure for Windows users:

Page 6

Battery mode

Low battery

Overload

Fault

Bypass mode

Sounds every 4 seconds

Sounds every second

Sounds every 0.5 second

Continuous sound

Sounds every 10 seconds

3-2. LCD panel

3-3. Audible alarm

ON/Mute +

Select button

Select + OFF/Enter

Button

Switch to bypass mode: When the utility power is normal, press ON/Mute and Select buttons simultaneously for 3 seconds to transfer the UPS to bypass mode. This action will be ineffective if the input voltage is not within an acceptable range.

Button Function

Exit setting mode or return to the upper menu: When the UPS is on setting mode, press the ON/Mute and Select buttons simultaneously for 0.2 seconds to return to the upper menu. If it is already in top menu, press these two buttons at the same time to exit the setting mode

Rack or Tower display switch: Press the Select and OFF/Enter buttons simultaneously for 3 seconds. The display changes from/to Rack to/from Tower.

Rack display

Load info

Battery info

UPS status

Battery info

Warning and fault info/ Setting operation

Backup time info

Input/output and Battery info

Warning & Fault info/ Setting operation

Backup time info

Input/output

and Battery info

UPS status

Tower display

Load information

UPS status

Battery information

Display

Function

Backup time information

Overload indicator

Indicates the load or the UPS output is short circuited.

Indicates that the programmable management outlets are working.

The UPS is on and supplying utility power to the connected equipment.

Indicates that the UPS is working in converter mode.

Indicates the UPS is working in bypass mode.

Indicates the UPS is supplying power to the loads directly from the mains.

Indicates that the UPS alarm is disabled.

Indicates the battery charger is working.

Low battery level and low voltage indicator.

Battery fault indicator.

Battery level indicator at 0-24%, 25-49%, 50-74%, and 75-100% of its capacity.

BATTERY

25% 50% 75% 100%

Indicates input voltage, input frequency, battery voltage, output voltage and output frequency. V: voltage, Hz: frecuency

Settings

Input/Output & Battery information

Load information

Display

Indicates the remaining backup time in pie chart.

Function

Backup time information

Fault information

Indicates the remaining backup time in numbers. H: hour, M: minute.

Warns that an internal fault has been detected.

Indicates that configuration parameters are being set.

Load level indicator at 0-24%, 25-49%, 50-74%, and 75-100% of its capacity

Warning and fault code indicators. The meaning of the codes is listed in the section below.

INPUT BATT OUTPUT

V Hz

25%

LOAD

50% 75% 100%

Page 7

Interface Setting

For 200/208/220/230/240 VAC, you may choose any of the following output voltages

200: the output voltage is 200VAC 208: the output voltage is 208VAC 220: the output voltage is 220VAC 230: the output voltage is 230VAC (Default) 240: the output voltage is 240VAC

For 100/110/150/120/127 VAC you may choose any of the following output voltages

100: the output voltage is 100VAC 110: the output voltage is 110VAC 115: the output voltage is 115VAC 120: the output voltage is 120VAC (Default) 127: the output voltage is 127VAC

3-4. Abbreviations on the LCD display

3-5. UPS parameter settings

01: Output voltage settings

Enable

Disable

Escape

High loss

Low loss

Site fault

EPO

Over temperature

Charger failure

Frecuency is unstable in bypass mode

EEPROM error

Fan failure

Battery replacement

Abreviation Display content Meaning

HS LS ON OK sf

Parameter 2

Parameter 1

Two parameters need to be configured in order to set up

the UPS. Refer to following diagram.

Parameter 1: it is used for the different configuration

options. Please refer to the table below.

Parameter 2: it represents the setting information or

values of each program.

02: Frequency Converter enable/disable

Interface Setting

Activates or cancels the converter mode.

CF ENA: Enable converter mode CF DIS: Disable converter mode (Default)

03: Output frequency settings

Interface Setting

Use this menu to define the initial frequency on battery mode:

BAT 50: The output frequency is set to 50Hz BAT 60: The output frequency is set to 60Hz

If the converter mode is enabled, the following options will be available:

CF 50: The output frequency is set to 50Hz CF 60: The output frequency is set to 60Hz

04: ECO enable/disable

Interface Setting

Activates or cancels the ECO mode.

ENA: the ECO mode is enabled DIS: the ECO mode is disabled (Default)

05: AECO enable/disable

Interface Setting

Activates or cancels the advanced ECO mode.

ENA: the advanced ECO mode is enabled DIS: the advanced ECO mode is disabled (Default)

Page 8

06: ECO voltage range setting

07: Bypass enable/disable

Interface Setting

Use this menu to set the acceptable high voltage point and low voltage point for ECO & AECO mode by pressing Down key or Up key. HS: High loss voltage in ECO & AECO modes. For 200/208/220/230/240 VAC models, the setting range in parameter 3 is from +7V to +24V of the nominal voltage. (Default: +12V) For 100/110/115/120/127 VAC models, the setting range in parameter 3 is from +3V to +12V of the nominal voltage. (Default: +6V) LS: Low loss voltage in ECO & AECO modes. For 200/208/220/230/240 VAC models, the setting range in parameter 3 is from -7V to -24V of the nominal voltage. (Default: -12V) For 100/110/115/120/127 VAC models, the setting voltage in parameter 3 is from -3V to -12V of the nominal voltage. (Default: -6V)

08: Bypass voltage range setting

Interface Setting

Parameter 3: Use it to activate or cancel the Bypass mode. ENA: Bypass enabled DIS: Bypass disabled

Interface Setting

Parameter 2 & 3: Press the UP or Down key to choose the

acceptable high and low voltage values for Bypass operation HS: High voltage adjustment in bypass mode For 200/208/220/230/240 VAC: 230-264: High voltage setting ranges from 230VAC to 264VAC as set in parameter 3. (Default: 264VAC) LS: Low voltage adjustment in bypass mode For 200/208/220/230/240 VAC: 170-220: Low voltage setting ranges from 170VAC to 220VAC as set in parameter 3. (Default: 170VAC)

Page 9

Interface Setting

DIS: Disables the runtime limit timer, in which case backup

time will depend on battery capacity. (Default) Note: When setting this parameter to “0”, the backup time will only last 10 seconds.

Use this setting to configure the backup time on battery mode for general outlets. 0-999: Sets the backup time in minutes, from 0-999 for general outlets on battery mode.

Interface Setting

HS: Bypass high frequency point

For 50Hz output frequency models: 51-55Hz: Sets the frequency high loss point from 51Hz to 55HZ (Default: 53.0Hz) For 60Hz output frequency models: 61-65Hz: Sets the frequency high loss point from 61Hz to 65Hz (Default: 63.0Hz) LS: Bypass low frequency point For 50Hz output frequency models: 45-49Hz: Sets the frequency low loss point from 45Hz to 49HZ (Default: 47.0Hz) For 60Hz output frequency models: 55-59Hz: Sets the frequency low loss point from 55Hz to 59Hz (Default: 57.0Hz)

Use this menu to set the acceptable high frequency point and acceptable low frequency point for Bypass mode by pressing the Down key or Up key.

09: Bypass frequency range setting

11: Backup time setting for programmable outlets

Interface Setting

Parameter 3: Sets the backup time limits for the

programmable outlets. 0-999: Use this setting to define the programmable outlets backup time in minutes, from 0-999, in order to connect non-critical devices on battery mode. (Default:999)

10: Programmable outlets enable/disable

Interface Setting

Parameter 3: Activates or cancels the programmable

outlet feature.

ENA: Programmable outlets enabled DIS: Programmable outlets disabled (Default)

Interface Setting

Use this setting to configure the charger current to be applied. When the UPS is equipped with an additional charge, ther available setting options are 2/3/4. 2/3/4: Sets the maximum charger current in 2/3/4 amperes. Long-run models have settings of 1/2/4/6/8. available.

.1/2/4/6/8: Sets the maximum charger current in 1/2/4/6/8

amperes. (Default: 8A)

Interface

Use this setting to configure the boost voltage level. 225-240: Sets the charger boost voltage from 225 to 240 (unit: 0.01V/cell). (Default: 236)

12: Backup time setting for general outlets

13: Battery total Ah setting

14: Maximum charger current setting

15: Charger boost voltage setting

Interface Setting

Use this setting to configure the total battery capacity in Ah for the UPS sytem. 7-999: Sets the battery total capacity from 7-999 in Ah. Please set the correct battery total capacity if an external battery bank is connected.

Page 10

16: Charger float voltage setting

00: Exit setting

3-6. Operation mode description

Interface

Use this setting to determine the float voltage level. 220-233: Sets the charger float voltage from 220 to 233 (unit: 0.01V/cell). (Default:228)

Operation mode

Online mode

ECO mode (Efficiency Corrective Optimizer)

Frequency Converter mode

Battery mode

AECO mode (Advanced Efficiency Corrective Optimizer)

Description LCD display

Rack display Tower display

Bypass mode

Standby mode

Fault

When the input voltage is within acceptable range, the UPS will supply pure and stable AC power to connected loads. The UPS will also charge the battery in online mode.

Energy saving mode: When the input voltage is within the voltage regulation range (±3%V max), the UPS will bypass voltage to loads for energy saving. PFC and INVERTER are still active in this mode.

When the input voltage is within the voltage regulation range (±3%V max), the UPS will bypass voltage to loads for energy saving. PFC and INVERTER are disabled in this mode.

When input frequency is between 40Hz and 70Hz, the UPS can be set at a constant output frequency, of 50Hz or 60Hz. The UPS will still charge the battery when operating in this mode.

When the input voltage exceeds the acceptable range or during a power failure, the UPS will start supplying power from the battery while the alarm will beep every 5 seconds.

When input is within acceptable voltage range but the UPS is overloaded, the UPS will transfer to bypass mode or it can be manually changed to bypass mode using the front panel controls. The alarm will sound once every 10 seconds in this case.

The UPS is powered off and there is no power supplied to the loads, but batteries can still be charged.

The UPS is in fault mode when it fails to provide output power to the loads. The fault icon flashes on the LCD display even though the UPS information is still being displayed on the screen.

Page 11

3-7. Fault codes

4. Troubleshooting guide

If the UPS system does not operate correctly, use the table below to troubleshoot the problem.

3-8. Warning indicators

Beeps once every 2 seconds

Beeps once every second

Beeps once every 2 seconds

EPO enable

Over temperature

Charger failure

Battery fault

Bypass out of range

Unstable bypass frequency

Low battery

Overload

Battery is not connected

Overcharge

Site wiring fault

Warning Icon (blinking) Code Alarm

EEPROM error

Fan failure

Battery replacement

Beeps once every 2 seconds

Even though the mains supply is normal, there are no status indicators or alarms.

The icon and the warning code become illuminated on the LCD display, and the alarm starts beeping once every

2 seconds.

The and the icons become illuminated on the LCD display, and the alarm starts beeping once every 2 seconds.

The and icons become illuminated on the LCD display and the alarm starts beeping once every 2 seconds.

Fault code 27 and the become illuminated on the LCD display, and the alarm starts beeping continuously.

The and icons become illuminated on the LCD display, and the alarm starts beeping every second.

Fault code 43 becomes illuminated along with the icon on the LCD display, and the alarm starts beeping continuously

The AC input is connected to the UPS outlet.

The AC input cable is not properly connected.

Line and neutral conductors of UPS input are reversed.

The external or internal battery connection is incorrect.

Battery voltage is too low or the charger fails

UPS is overloaded

UPS is overloaded. Devices connected to the UPS are fed directly from utility power via the Bypass

After repetitive overloads, the UPS is locked in Bypass mode. Connected devices are fed directly from utility power.

The UPS shuts down automatically upon detecting the overload condition in the output

Battery voltage is too high or the charger is fault

Rotate mains power socket by 180° and then connect to UPS system

Check if all batteries are properly connected.

Contact your dealer or service center

Please contact the dealer or service center

Remove excess loads from the UPS output

Remove excess loads from UPS output

Remove excess loads from the UPS output first. Shut down the UPS completely before restarting the unit once again

Remove excess loads from the UPS output and restart the unit once again

EPO function is enabled

Check to make sure the power cord is firmly connected to a AC wall socket

Set the circuit in its closed position to disable the EPO function

Plug the power cord to a wall socket.

Symptom Possible cause Remedy

Fault code 28 and the icon become illuminated on the LCD display and the alarm starts beeping continuously.

Fault event

Fault code

IconFault event

Inverter output is short circuited

Battery voltage too high

Battery voltage too low

Excessive temperature

Overload

Charger failure

Bus start failure

Bus over

Bus under

Inverter soft start failure

High inverter voltage

Low inverter voltage

Page 12

MPN

General

Input

Output

Battery

Alarms/Indicators

Physical appearance

Additional information

Capacity

FDC-1502R

1500VA/1350W

Double conversion

200-240VAC

40Hz-70Hz

NEMA 5-15P

220VAC

47Hz-53Hz or 57Hz-63Hz

>90%

Pure Sine Wave

4 NEMA 5-15R

0ms

0.9

4ms4ms

Included

12V/9 Ah (3)

4 min at full load

4 hours to 90% capacity

RS-232, USB

42.1lb

6.0ft

Battery mode: Sounds

every 4 seconds

Low battery: sounds every

second Overload: Sounds every 0.5 second

Fault: Continuous sound

Graphical LCD with blue

backlight

ForzaTracker

or optional SNMP card

15x17.3x3.5in

Two years for UPS,

One year for battery

50Hz±0.25Hz or 60Hz±0.3Hz

L-N: 624J

L-G: 420J

N-G: 420J

FDC-3002R

6.0ft

23.6x17.3x3.5in

66.4lb

Two years for UPS,

One year for battery

3000VA/2700W

Double conversion

200-240VAC

40Hz-70Hz

L-N: 624J

L-G: 420J

N-G: 420J

NEMA 5-15P

220VAC

47Hz-53Hz or 57Hz-63Hz

>91%

Pure Sine Wave

6 NEMA 5-20R

0ms

0.9

Included

12V/9 Ah (6)

4.5 min at full load

4 hours to 90% capacity

RS-232, USB

Battery mode: Sounds

every 4 seconds

Low battery: sounds every

second

Overload: Sounds

every 0.5 second

Fault: Continuous sound

Graphical LCD with blue

backlight

ForzaTracker

or optional SNMP card

50Hz±0.25Hz or 60Hz±0.3Hz

Topology

Nominal voltage

Frequency

Joules

AC plug style

Nominal voltage

Frequency (synchronized)

Frequency (battery)

Efficiency (AC mode)

Waveform

Total outles

Battery type and quantity

Backup time

Recharge time

Visual indicators

Audible

Cord length

Dimensions

Weight

Warranty

Communication ports

USB management

Transfer time (line to battery)

Transfer time (inverter to bypass)

Power factor

Yes YesModem/phone/network

surge protection

Power management

software

6. Specifications

5. Storage and maintenance

The UPS system contains no user-serviceable parts. If the battery service life (3~5 years at 25°C ambient temperature) has been exceeded, the batteries must be replaced. In this case, please contact your dealer or service center.

Storage

Charge the UPS for at least 5 hours before storing the unit. Cover the UPS, and place it upright in a cool, dry location. During storage, recharge the battery in accordance with the following table:

Fault code 14 becomes illuminated and the alarm starts beeping continuously.

Fault codes 01, 02, 03, 11, 12, 13 and 41 become illuminated on the LCD display, and the alarm starts beeping continuously.

Fault code is shown as 45 on LCD display. At the same time, the alarm starts beeping continuously.

Battery backup time is shorter than its nominal value.

The UPS shuts down automatically upon detecting the overload condition in the output.

Defective batteries

Batteries are not fully charged.

Charge the batteries for at least 5 hours and then check their capacity. If the problem persists, consult your dealer.

Contact your dealer for a replacement

A UPS internal fault has occurred. There are two possible causes:

1. Power is continued to be supplied to the load, but is done directly from the AC grid via a bypass.

2. Power is no longer supplied to the load

Check the output wiring and if connected devices are short-circuited.

Please contact the dealer or service center.

Symptom Possible cause Remedy

There is no output voltage from the charger and the battery voltage is below 10V/PC.

Please contact the dealer or service center.

Batteries must not be discarded as regular household waste! As part of the company’s eco-friendly approach, we encourage you to follow all applicable local waste regulations to dispose of your used devices and batteries properly.

Storage temperature Recharge frequency Runtime

-25°C - 40°C

-40°C - 45°C

Every 3 months

Every 2 months

1-2 hours