Page 1
0.5m
5m
1.2m
0.3m
0.5m
Round 30mm
（40065）
Round 45mm
（40066）
Baru 10 Light Decking Kit
Ins ZN 40065 40066 - B
Instruction Manual
ZN 40065 & 40066
Product Specification:
LED deck light
Input voltage: 100-240VAC ~ 50/60Hz
Output voltage: 12VDC
Lamp: 40065 -10 x 0.5W LED module, 40066 - 10 x 1W LED module
LED color: 40065 - RGB, 40066 - RGB+daylight white 6500K
Product dimension: 40065 - Dia 30 x 0.4mm projection, 40066 - Dia 45 x 0.4mm projection
Lumen output: 40066 - 200Lm at daylight white 6500K mode
Deck cutout size: 40065 - Dia 24mm, 40066 - Dia 32mm
Depth into Deck: Min. 35mm
iOS 9.0 or higher, Android 4.4 or higher
WiFi IEEE 802.11N, 2.4GHz
Warning:
- Install in accordance with the IEE Wiring regulations and current Building Regulations.
- This system operates at Safety Extra Low Voltage (12V), via a LED driver. Never connect the light fittings directly to the mains without using a LED driver
- Do not look directly into the light source.
- Do not attempt to disassemble any parts.
- LED driver can support a maximum of up to 10 LED light units. Do not attempt to connect further light units.
- The plug-in LED driver has no special protection against moisture and must be situated indoors.
- LED driver is not suitable for use with dimmers.
- Always disconnect the LED driver from the mains when installing or maintaining this system.
- This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
- The product is designed to be fitted horizontally and vertically in decking, walls, steps etc.. It is not suitable for installation directily into the ground.
- Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
- This system works via WiFi control, please sure that BEFORE you install your kit there is good 2.4GHz WiFi signal coverage in the location you going to
place the smart WiFi controller.
- Only support 2.4GHz WiFi networks with WEP and WPA/WPA2 encryptions. Portal and WPA/WPA2 enterprise are not supported.
- 5GHz WiFi is not supported un-secured open networks and hidden SSIDs are not supported.
- If you are experiencing problems, please consult a qualified electrician.
Installation:
- Note that the switch is turned off before installation.
- Plan the desired layout carefully, ensuring the cables will reach the distances between the LED driver and each LED light unit.
- Avoid locating any cables in positions that would cause a trip hazard. Position cables away from areas where they may be at risk from being cut,
trapped or damaged.
- After deciding the layout, ensure the cables are long enough to connect to the desired positions.
- Drill the mounting holes for the LED light units taking care not to damage any pipes or mains cables beneath the mounting surface.
These require a Dia 24mm (40065) Dia 32mm (40066) cutout hole.
- Feed the connector and cable of each LED light unit through the mounting holes and push unit into the hole to secure.
- Connect each LED light unit to the next LED light unit ensuring the arrows on connectors are facing each other and all connectors are fully fitted.
- Connect the extension cable and WiFi receiver to the LED driver.
- Connect the LED driver into the mains socket and switch on.
IP67
This product is suitable for dimming
with ‘Tuya’ app, Amazon Echo or
Google Home.
We recommend putting the wifi receiver
within 20-25 meters of your WI-FI Hub.
This will vary depending on the
strength of your WI-FI coverage.
TUYA smart products are only
supported on 2.4G WIFI bands.
We recommend testing the position
before full installation.
30mm dia head
45mm dia head
40065
Depth into deck: Min. 35mm
Deck cutout size: Dia 24mm
40066
Depth into deck: Min. 35mm
Deck cutout size: Dia 32mm
WiFi receiver
LED
!
+ -
IP67Indoor
√
×
Care and maintenance:
It is recommended to regularly spray on or apply by a cloth a water displacing oil to clean and protect the metal surfaces. This will provide protection from
the elements especially if living near the sea
Helpline
If you receive this item with parts broken or missing, please telephone: 0333 0050077
Please have ready your name, address, tel. no., product reference, where purchased and parts required. An answering service is in operation outside oce
hours and during busy periods. We regret that we are unable to give advice on internal house wiring.
Cascade Holdings Ltd, Gorse Mill, Gorse Street, Chadderton, Oldham. OL9 9RJ
EU Authorised Representative: Authorised Rep Compliance, Ground Floor, 71 Lower Baggot Street, Dublin, Ireland, D02P593
Page 2
TUYA SMART INTELLIGENT LIGHTING USER MANUAL
STEP 1
You will need an active internet connection. Scan the
QR code to download the App or login to Google Play
or the App Store on your mobile phone or tablet and
search ‘Tuya Smart’. Click ‘Download’. Once downloaded,
click on the app to open and proceed to login or register.
App store GooglePlay
App store/Google Play
STEP 2
Read the Privacy Policy carefully. Click 'Agree' if you wish to
continue with the setup. You can choose to register by email
or phone; complete all required elds.
Click 'Obtain verication code'.
Enter the verication code that you receive.
Set a Password.
Welcome to Tuya Smart.
STEP 3
Click 'create family' to turn on your Tuya Smartlife.
Enter family name, or any name you wish.
Set location. Tick or untick relevant rooms according to the
property.
If the room is not present, add a room, e.g.'Patio'. You can
change room settings at anytime.
STEP 4
It is now time to add your smart lighting.
Click 'Add Device' or the '+' icon in the top right hand corner
Click 'Lighting' on the left hand side.
Click 'Lighting (BLE+Wi-Fi)' on the main screen.
Turn the light on and leave for 10 seconds.
Turn ofF and on repeatedly, 3 times (2-3 seconds between clicks)
When the light starts to blink repeatedly, click 'Conrm lights
blink rapidly'.
Wi-Fi name
STEP 5
NOTE: Only supports 2.4 GHz Wi-Fi networks
Enter your Wi-Fi detai
Once successfully connected, you can keep the default name
or change it and assign the light to a room.
Finally, click 'Completed'. Congratulations, you are now free to
enjoy controlling your light through the smart app.
STEP 6
Click the icon in the top right hand corner of the app to
display additional options, such as pairing with your Amazon
Alexa or Google Assistant.
Click an icon in the Supported Third-Party Control section.
Follow the connection instructions described here.
ls and click 'OK'.
Loading...