USER GUIDE
700C URBAN HYBRID+
LIGHTWEIGHT ROAD BIKE
FS700CALRBA
SAFETY
This user guide was written to help you get the most performance, comfort, enjoyment and
safety when riding your new bicycle. It is important for you to understand your new bike.
By reading this user guide before you go out on your first ride, you’ll know how to get the
most from your new bicycle. It is also important that your first ride on your new bicycle is
taken in a controlled environment, away from cars, obstacles, and other cyclists.
Before First Ride
• Before first use, please double-check the function of all the parts of your bike. If you
have any doubts or if you detect a problem, please contact Kogan.com for support.
• Respect local and national road traffic regulations.
• For your safety, it is highly recommended that you wear a certified helmet.
• When used during heavy rain, snow, in slippery conditions or in the case of low visibility,
be careful and adjust your speed.
• The illustrations in this user guide are used simply to provide examples; the components
of your bicycle might differ. In addition, some of the parts shown might be optional and
not part of your bicycle's standard equipment.
• The following user guide is only a guide to assist you and is not a complete or
comprehensive manual of all aspects of maintaining and repairing your bicycle. If you
are not comfortable, or lack the skills or tools to assemble the bicycle yourself, you
should take it to a qualified mechanic at a bicycle shop. Additionally, you can contact
Kogan.com for support.
& WARNINGS
WARNING:
Always wear a properly fitted helmet when you ride your bicycle. Do not ride at night.
Avoid riding in wet conditions
Helmets
Always wear a properly fitted, Australian standard approved helmet while riding your bike.
Correct
Helmet fits snug
and covers forehead
Forehead is exposed and
vulnerable to serious injury
Incorrect
General Warning
Bicycle riding can be a hazardous activity even under the best of circumstances. Proper
maintenance of your bicycle is your responsibility as it helps reduce the risk of injury. This user
guide contains many WARNINGS and CAUTIONS concerning the consequences of failure
to maintain or inspect your bicycle. Many of the warnings and cautions say, “you may lose
control and fall”. Because any fall can result in serious injury or even death, we do not repeat
the warning of possible injury or death whenever the risk of falling is mentioned.
Kogan.com does not encourage: trick riding, ramp riding, jumping, aggressive riding, riding
on severe terrain, riding in severe climates, riding with heavy loads, riding double,
commercial activities; such use is inherently dangerous and can cause serious injury to the
rider.
Note to Parents
It is a tragic fact that most bicycle accidents involve children. As a parent or guardian, you
bear the responsibility for the activities and safety of your child. Among these responsibilities
are to ensure;
• That the bicycle that your child is riding is properly fitted to the child
• That it is in good repair and safe operating condition
• That the play of young children is supervised by an adult
• That you and your child have learned, understand and obey not only the applicable
local motor vehicle, bicycle and traffic laws, but also the common sense rules of safe
and responsible bicycling
As a parent, you should read this user guide before letting your child ride the bicycle. Please
ensure that your child always wears an approved bicycle helmet when riding.
Choosing the Correct Size Bike
Frame Sizing:
When selecting a new bicycle, the correct choice of frame size is a very important safety
consideration. To determine the correct size bicycle for the rider:
• Straddle the assembled bicycle with feet shoulder width apart and flat on the ground.
• There must be at least one inch (2.5cm) of clearance between the highest part of the
top tube of the bicycle and the crotch of the rider with the tires properly inflated.
• To measure the inseam, use a measuring tape to measure from the ground (with shoes
on) to the inseam of your pants.
• Subtract the standover height from the inseam measurement to ensure that you have
the recommended amount of clearance. If you have less than one inch or more than
three inches (2.5 to 7.5 cm), you may need to move up or down a frame size.
Weight Limit:
The maximum structural weight recommendations for our bicycles are;
• 20 inch bicycles: 80 kg
• Adult bicycles up to 26 inches: 125 kg
CAUTION: For safe and comfortable riding there should be a clearance of no less
than 1 inch between the inseam area of the intended rider and the top tube of the
bicycle frame, while the rider straddles the bicycle with both feet flat on the ground.
WARNING: If the bicycle is too large the rider cannot reach the pedals easily, or the
ground when stopping which may result in loss of control and/or injury.
Road Safety
Like any sport, bicycling involves risk of injury and damage. You need to know and practice
the rules of safe and responsible riding.
• In the interest of safer cycling, make sure you read and understand this user guide. Note
and perform pre-ride safety checks.
• Some states and local laws may require that your bicycle be equipped with a warning
device such as a horn or bell and a front and rear light if the bicycle is to be ridden aer
dark.
• Always wear shoes when riding a bicycle and avoid loose fitting clothes.
• Check your brakes frequently. The ability to stop your bicycle is critical. Roads are
slippery when wet so avoid sharp turns and allow more distance for stopping. Caliper
brakes may become less efficient when wet. Leaves, loose gravel, and other debris can
also affect stopping.
• Always ride in the same direction as traffic. Never ride against traffic.
• Stop and look before you leave an alley, driveway, or parking lot. Ride only when it is
clear.
• Follow the traffic flow in a straight line and stay close to the curb or in the bike lane,
when available. Watch for cars moving in and out of traffic.
• Obey all traffic regulations. Most traffic regulations apply to bike riders as well as
automobile operators.
• One rider per bike. Never carry other riders. This is dangerous and makes the bike harder
to control.
• Always be alert. Pedestrians have the right of way. Be alert when riding near parked
cars and ride far enough away from cars so that you won’t get hit if someone opens the
car door.
• Use caution at all intersections and stop signs. Stop and look both ways before
proceeding.
• Use hand signals. Communicate by using hand signals to tell other drivers what you are
going to do. Signal before turning unless your hand is needed to control the bike.
• Proper lights are recommended if you ride at night. Be sure to have a strong head-light,
a tail light, and a full set of reflectors. Check that reflectors are clean, straight, unbroken,
and securely mounted.
• Never carry packages or objects which obstruct vision.
• Never hold onto a moving vehicle while riding.
• The kick-stand is designed to support the bicycle only, not the bicycle and the rider.
• Avoid the following hazards: drain grates, potholes, so road edges, gravel, sand, wet
leaves, and/or any obstruction in the road. Failure to do so could cause wheel(s) to
buckle and result in personal injury to the rider.
• Wet weather riding - riding your bicycle in wet conditions is not recommended. In wet
conditions traction and braking power is reduced. Riding in such conditions could result
in personal injury.
• Proper helmet use. A helmet that meets Australian standards should always be worn
when riding a bicycle. The helmet should fit properly and be worn on the crown of the
head, not tipped back. Ensure to replace your helmet at least every three years to
ensure the structural integrity of the foam. Replace aer impact, regardless of lack of
visible damage to helmet.
• Use bike lanes when available. Also note that in certain states, cars may use bike lanes
when turning.
• Respect “bicycles are prohibited” signs.
Night Riding
Riding a bicycle at night is much more dangerous than riding during the day. A cyclist is very
difficult for motorists and pedestrians to see. Therefore, children should never ride at dawn,
dusk or at night. Adults who choose to accept the greatly increased risk of riding at dawn,
dusk or at night need to take extra care both riding and choosing specialized equipment
which helps reduce that risk. Consult your local bicycle shop about night riding safety
equipment.
WARNING: Reflectors are not a substitute for required lights. Riding at dawn, at
dusk, at night or at other times of poor visibility without an adequate bicycle lighting
system and without reflectors is dangerous and may result in serious injury or death.
WARNING: Do not remove the front or rear reflectors or reflector brackets from your
bicycle. They are an integral part of the bicycle’s safety system. Removing the
reflectors reduces your visibility to others using the roadway. Being struck by other
vehicles may result in serious injury or death.
Child Safety Rules
To avoid an accident, teach children good riding skills with an emphasis on safety.
• Always wear a properly fitted helmet.
• Do not play in driveways or on the road.
• Do not ride on busy streets.
• Do not ride at night.
• Obey all traffic laws, especially stop signs and red lights.
• Be aware of other road vehicles behind and nearby.
• Before entering a street: Stop, look for traffic, enter only when safe.
• If riding downhill, be extra careful. Slow down using the brakes and maintain control of
steering.
• Never take your hands off the handlebars, or your feet off the pedals when riding
downhill.
SAFETY
Before every ride, it is important to carry out the following safety checks:
CHECKLIS
Brakes:
• Ensure front and rear brakes work properly.
• Ensure brake pads are not over worn and are correctly positioned
in relation to the rims.
• Ensure brake control cables are properly lubricated, correctly
adjusted, and display no obvious wear.
• Ensure brake control levers are properly lubricated and tightly
secured to the handlebar.
Derailleurs:
• Check that the front and rear derailleurs are adjusted and
functioning properly.
• Ensure that the shier levers are securely attached.
• Ensure that derailleurs, shi levers, and control cables are properly
lubricated.
• Shi through all the gears while pedaling to ensure that the
derailleurs are adjusted and functioning properly.
Cranks & Pedals:
• Ensure pedals are securely tightened to the cranks.
• Ensure cranks are securely tightened to the bottom bracket and
are not bent.
T
Frame & Fork:
• Check that the frame and fork are not bent, broken, or cracked.
• If either are found to be bent, broken, or cracked, they should be
replaced.
Wheels & Tires:
• Ensure tires are inflated to within the recommended range as
displayed on the tire sidewall.
• Ensure tires have tread and have no bulges or excessive wear.
• Ensure rims run true and have no obvious wobbles or kinks.
• Ensure all wheel spokes are tight and not broken.
• Check that axle nuts are tight.
• Do not over inflate.
Chain:
• Ensure chain is oiled, clean and runs smoothly.
• Extra care is required in wet or dusty conditions.
• On bicycles equipped with coaster brakes, check for proper chain
tension.
• Check to make sure your chain guard is tight and not touching the
crank or chain.
Bearings:
• Ensure all bearings are lubricated, run freely and display no excess
movement, grinding or rattling.
• Check headset, wheel bearings, pedal bearings and bottom
bracket bearings.
Handlebars:
• Ensure handlebar and stem are correctly adjusted and tightened,
and allow proper steering.
• Ensure that the handlebars are set correctly in relation to the forks
and the direction of travel.
OVERVIEW
Bike
Tools Supplied
Allen (6mm) &
Phillips head key
5mm Allen key
4mm Allen key
13-15mm Spanner
ASSEMBL
Getting Started
Open the box and check that all parts are present.
We strongly recommend reading the user guide before beginning. If you aren’t comfortable
with the assembly, you should bring your bike to your local bike shop to have a qualified
mechanic put it together for you. Please ensure you need to read this entire user guide
before you ride or let anyone else ride it.
CAUTION: As you assemble the bike, it’s a good idea to place a little white grease
or anti-seize compound on the seat post, stem and threads of the bolts to prevent
rusting.
Step 1: Aligning the forks
• The frame, handlebars, front wheel, and other components are attached with zip ties.
Li everything out in one piece, and set it down, with the chain facing upwards.
• Remove the zip ties, and remove any padding or packaging.
• First, align the fork. Rotate it, to ensure it moves freely without binding (Figure 1), making
sure the fork is pointing in the right direction, with the fork blades facing forward
(Figure 2).
Y
Figure 1 Figure 2
Step 2: Attaching the pedals
Before your first ride, please do the following checks and ensure your pedals are attached
correctly.
• There is a right side pedal marked “R” and a le side pedal marked “L”
• The right pedal has a RED sticker, the Le pedal has a GREEN sticker.
• Pedal marked “R” has right hand threads. Tighten in a clockwise direction.
• Pedal marked “L” has le hand threads. Tighten in a counterclockwise direction
(Figure 3).
• Aer putting some white grease on the threads of the pedal, place the pedal into the
crank, and use your fingers to get it started. Threading it in can be tricky, so make sure
to do it correctly. The top of the thread will rotate towards the front of the bike to tighten
the pedals.
• Once finger tightened, use a 15mm open-ended spanner to torque them down. They
are properly tightened when the pedal spindle, which is the axle that the pedal platform
spins around, begins to bite into the metal on the crank.
Figure 3
WARNING: Incorrect installment of pedals into a crank arm will cause irreparable
damage. Unless the shoulder of the pedal spindle is tight to the face of the crank
arm, the pedal may back out causing serious injury or death. Make it tight so the
shoulder is in complete contact with the surface of the crank arm.
Step 3: Installing the quick-release wheels
• Place the wheel in a central position between the frame dropouts and the fork.
• Install the quick release lever and ensure each side has a spring.
• Tighten the adjusting nut (Figure 4).
• Close the quick-release system. In order to prevent it coming loose, it is necessary to
turn the adjusting nut such that the closing force of the release lever is at least 12 daN
(about 12 kg).
• To increase the closing force: turn the adjusting nut clockwise (anticlockwise to reduce
the force).
Figure 4
WARNING: Failure to obey these steps can allow the front wheel to loosen or
dislodge while riding. This can cause injury or death to the rider or to others.
Step 4: Installing the seat
• Add some white grease to the inside of the seat tube, and slide the seat post into the
bicycle.
• Make sure that the minimum insertion mark is completely covered and that the seat is
pointing forward in alignment with the bicycle (Figures 5 & 6).
Figure 5
WARNING: The seat post must be inserted far enough so that the minimum
insertion marks cannot be seen.
Step 5: Installing the rear seat reflector
• Remove the seat post and seat.
• Loosen the screw on the clamp of the reflector until you can slide the reflector over the
seat post.
• Once the reflector is on the seat post, reinsert the seat post back into the seat tube.
• Position the reflector so that it is perpendicular to the ground, and move it up on the
seat post until it can be seen above the tire when viewing the bike from the rear
(Figure 7).
Figure 7
Figure 6
Step 6: Quick release lever
• This bike has a quick release lever (Figure 8), tighten it by holding the lever in the “open”
position and tightening the nut on the opposite side by hand.
• Slowly close the quick release lever, and you should notice resistance when the lever is
half way shut.
• Continue to push the lever until it is in the “closed” position, and the word “close” is
showing. The seat should not be able to move back and forth, up and down, or side to
side with the quick release lever in the closed position.
• Ensure the lever is also parallel with the seat clamp itself. You should only need one
hand to close the quick release lever.
• If you need two hands, the seat clamp is too tight. Loosen the nut on the clamp until
only one hand is needed to close the seat clamp
Figure 8
CAUTION: Operate the quick release lever by hand only. Do not use a hammer or
any other tool to tighten the quick release lever.
Testing Seat Tightness
Aer installing the seat post into the bicycle and tightening the clamp, test the tightness of
the saddle. Hold the seat firmly with both hands and try to move it side to side. The seat
post should not move at all. The seat post and seat also should not move when the rider is
seated. Ensure the seat clamp nuts at the top of the seat post are tight so that the seat
does not tip forward or backwards.
Handlebar/Stem
This bike features a threadless stem (Figure 9) the stem has been pre-installed, to change
handlebar height requires moving height adjustment spacers from below the stem to above
the stem, or vice versa.
Alternatively you’ll have to get a stem of different length or rise. Do not attempt to do this
yourself, as it requires special knowledge and your bicycle should be taken to a professional
bike shop for this adjustment.
Figure 9
Step 7: Securing the handlebars
• Loosen the bolts on the side of the stem, slide the stem into place, making sure it lines
up with the fork .
• Check the gap between the steerer tube and stem, ensuring there is enough space to
reinstall the cap and bolt.
• Snug the pre-load bolt on top. Then tighten the two bolts on the side of the stem,
alternating each bolt.
• The handlebars should come attached to the stem. Simply ensure that the brake and
derailleur cables track smoothly, and that the handlebar bolt(s) are properly tightened
with a 4, 5, or 6 mm Allen Wrench (Figures 10-12).
• In the case of a 2 or 4-bolt stem, tighten the bolts alternating between bolts every few
turns.
Figure 10
WARNING: To prevent steering system damage and possible loss of control, the
stem must be inserted enough so that the minimum insertion marks are completely
covered (Figure 13).
Figure 13
Testing Handlebar Tightness
To test the tightness of the stem, straddle the front wheel between your legs tightly (Figure
14). Try to turn the handlebar back and forth. The handlebar should not slip or move
independently of the front wheel at all. If the handlebar does move, re-align the stem with
the front wheel and tighten the stem bolt. Re-test to make sure the stem is secure with the
same process.
To test the tightness of the handlebar, hold the bike stationary and try to rotate the ends of
the handlebar up and down or move the bar forward and back. If the handlebar moves,
loosen the handlebar clamp nut or bolts evenly to re-position and then re-tighten. Repeat
the test until the bars will not move.
Figure 11 Figure 12
Figure 14
Step 8: Brakes
• The brake cable has been pre-assembled thread the cable anchor nut.
• Squeeze the brake arms together against the rim of the wheel. Loosen the nuts on the
brakes shoes and turn until they match the angle of the rim. Tighten the nuts securely.
• Loosen the cable anchor nut and squeeze both brake arms together so that both brake
shoes are in contact with the rim, pull all the slack out of the brake cable, and securely
tighten the cable anchor nut.
• Spin the wheel, the brake shoes should not contact the rim at any point and should be
an equal distance from the rim on both sides.
• Make sure all nuts and bolts are securely tightened. Test the brake levers 20-25 times to
take care of any initial cable stretch. Be sure to tightly secure the brake fixing nut behind
the fork.
Figure 15
WARNING: When assembling or adjusting the brakes, make sure the cable anchor
nut is tight (Figure 15). Failure to securely tighten the nut could result in brake failure
and personal injury.
CAUTION: Do not ride the bicycle until the brakes are functioning properly. To test, apply the
brakes while trying to push the bike forward to make sure they will stop the bicycle. Never
ride a bicycle that is not functioning properly.
WARNING: Sudden or excessive application of the front brake may pitch the rider over the
handlebars, causing serious injury or death.
Check Your Brakes
Press each brake lever to make sure that there is no binding and that the brake pads press
hard enough on the rims to stop the bike. The brake pads should be adjusted so they are 1
mm to 2 mm away from the rim when the brakes are not applied. Brake pads should be
centered on the rim and the rear portion of each brake pad should be about 0.5 - 1.0 mm
farther from the rim than the front portion of the brake pad.
Step 9: Inflating the tires
Use a hand pump, foot pump, or floor pump to properly inflate the tires. The maximum
inflation (PSI) is shown on each tire sidewall (Figure 16). If your pump does not have a built in
gauge, use a separate pressure gauge to ensure the tires are inflated to the correct pressure.
Figure 16 Figure 17
WARNING: Tires must be properly inflated before riding. Never exceed the
maximum pressure (PSI) that is listed on the side of the tire.
WARNING: Be sure to check that the edge (beads) of both tires are evenly seated
the entire way around on both sides of the tire. Failure to do so may result in the tire
coming off of the rim, the tube popping (Figure 17), and a loss of control of the
bicycle, causing injury or even death.
Recommended Tire Pressures
The recommended pressure molded on the sidewall of your bicycle tires should match the
figures below. Use this as a general guide.
BMX- 35 - 50 psi
Mountain Bike - 40 - 65 psi
Road Touring - 70 - 90 psi
Hybrid/Crossbike - 60 - 100 psi
Road Racing - 110 - 125 psi
Step 10: Installing front reflector
Attach the white reflector to the front reflector bracket and secure to the fork or handlebar
using the hardware provided.
OPERATION
It’s important to your enjoyment and safety to understand how things work on your new
bicycle. Even if you’re an experienced cyclist, don’t assume that the way things work on your
new bike is the same as how they work on older bikes. Be sure to read and to understand this
section . If you have even the slightest doubt as to whether you understand something, talk
to your local bicycle specialist or contact Kogan.com for support.
Removing and Installing Bolt-on Wheels
Removing Bolt-on Front Wheel:
1. Open up the brake shoes.
2. With a 15mm box wrench or a 6 inch adjustable wrench, loosen the 2 axle nuts.
3. If your front fork has a clip-on type secondary retention device, disengage it and go to
Step 4. If your front fork has an integral secondary retention device, loosen the axle nuts
about six full turns; then go to Step 4.
4. Raise the front wheel a few inches off the ground and tap the top of the wheel with the
palm of your hand to knock the wheel out of the fork ends.
Installing a Bolt-On Front Wheel:
1. With the steering fork facing forward, insert the wheel between the fork blades so that
the axle sits firmly at the top of the slots which are at the tips of the fork blades. The
axle nut washers should be on the outside, between the fork blade and the axle nut. If
your bike has a clip-on type secondary retention device, engage it.
2. While pushing the wheel firmly to the top of the slots in the fork dropouts, and at the
same time centering the wheel rim in the fork, use a 6inch adjustable wrench or a 15mm
box wrench to tighten the axle nuts securely.
3. Close the brake shoes; then spin the wheel to make sure that it is centered in the frame
and clears the brake shoes.
Removing a Bolt-On Rear Wheel:
1. Open the rear brake shoes.
2. Shi the rear derailleur to high gear (the smallest rear sprocket) and pull the derailleur
body back with your right hand.
3. With a 15mm box wrench or a six inch adjustable wrench, loosen the 2 axle nuts.
4. Li the rear wheel off the ground a few inches, and with the derailleur still pulled back,
push the wheel forward and down until it comes out of the rear dropouts.
Installing a Bolt-On Rear Wheel:
1. Shi the rear derailleur to its outermost position and pull the derailleur body back with
your right hand.
2. Put the chain onto the smallest sprocket. Then, insert the wheel into the frame dropouts
and pull it all the way into the dropouts. The axle nut washers should not be on the
outside, between the frame and the axle nuts.
3. Tighten the axle nuts securely, using a 6 inch adjustable wrench or a 15mm box wrench.
4. Push the rear derailleur back into position.
5. Close the brake; then spin the wheel to make sure that it is centered in the frame and
clears the brake shoes.
Seatpost Quick Release
Many bikes are equipped with quick-release seat post binders. While a quick release looks
like a long bolt with a lever on one end and a nut on the other, in fact the quick release uses
a cam action to firmly clamp the seat post.
Adjusting the Quick Release Mechanism:
The action of the quick release cam squeezes the seat collar around the seat post to hold
the seat post securely in place. The amount of clamping force is controlled by the tension
adjusting nut. Turning the tension adjusting nut clockwise while keeping the cam lever from
rotating increases clamping force; turning it counterclockwise while keeping the cam lever
from rotating reduces clamping force. Less than half a turn of the tension adjusting nut can
make the difference between safe clamping force and unsafe clamping force.
CAUTION: The full force of the cam action is needed to clamp the seatpost
securely. Holding the nut with one hand and turning the lever like a wing nut with
the other hand until everything is as tight as you can get it will not clamp the
seatpost safely.
CAUTION: If you can fully close the quick release without wrapping your fingers
around the seat post for leverage, and the lever does not leave a clear imprint in the
palm of your hand, the tension is insufficient. Open the lever; turn the tension
adjusting nut clockwise a quarter turn; then try again.
Brakes Adjustment
For most effective braking, use both brakes and apply them simultaneously.
It is important for you to know which brake lever controls which brake on your bike. Ensure
that your hands can reach and squeeze the brake levers comfortably.
The braking action of a bicycle is a function of the friction between the brake surfaces usually the brake shoes and the wheel rim. To make sure that you have maximum friction
available, keep your wheel rims and brake shoes clean and free of lubricants, waxes or
polishes.
Progressive Brake Modulation
Brakes are designed to control the speed and to stop the bike. Maximum braking force for
each wheel occurs at the point just before the wheel stops rotating and starts to skid. Once
the tire skids, you lose most of the stopping force and all directional control.
You need to practice slowing and stopping smoothly without locking up the wheel. The
technique is called progressive brake modulation. Instead of jerking the brake lever to the
position where you think you will generate appropriate braking force, squeeze the lever,
progressively increasing the braking force. If you feel the wheel begin to lock up, release
pressure just a little to keep the wheel rotating just short of lockup.
It is important to develop a feel for the amount of brake lever pressure required for each
wheel at different speeds and on different surfaces. To understand this, experiment by
walking your bike and applying different amounts of pressure to each brake lever, until the
wheel locks.
CAUTION: Some bicycle brakes, such as linear-pull and disk brakes, are extremely
powerful. You should take extra care in becoming familiar with these brakes and
exercise particular care when using them. Applying these brakes too hard or too
suddenly can lock up a wheel, which could cause you to lose control and fall.
CAUTION: Sudden or excessive application of the front brake may pitch the rider
over the handlebars, causing serious injury or death.
Applying Brakes
When you apply one or both brakes, the bike begins to slow, but your body wants to
continue at the speed at which it was going. This causes a transfer of weight to the front
wheel, or, under heavy braking, around the front wheel hub, which could harm you.
A wheel with more weight on it will accept greater brake pressure before lockup; a wheel
with less weight will lock up with less brake pressure.
Do the following as you apply brakes and your weight shis forward:
• Shi your body toward the rear of the bike, to transfer weight back onto the rear wheel;
• At the same time, decrease rear braking and increase front braking force.
• This is important on steep descents, because descents shi weight forward.
The key to effective speed control and safe stopping are controlling wheel lockup and
weight transfer. Practice braking and weight transfer techniques where there is no traffic or
other hazards and distractions.
Everything changes when you ride on loose surfaces or in wet weather. Tire adhesion
reduces, so the wheels have less cornering and braking traction and can lock up with less
brake force. Moisture or dirt on the brake shoes reduces their ability to grip. The way to
maintain control on loose or wet surfaces is to go more slowly.
Adjusting Brakes
If either brake lever on your bike fails the Mechanical Safety Check you can restore brake
lever travel by turning the brake cable adjusting barrel counterclockwise, then lock the
adjustment in by turning the barrel's lock nut clockwise as far as it will go. If the lever still fails
the Mechanical Safety Check, or if you have any question about whether your brakes are
working properly have your brakes checked by a bicycle specialist or contact Kogan.com for
support.
CAUTION: The brake cable adjusting barrels are for minor adjustments only. For
major adjustments, see the “Step 9: Brakes” in the Assembly section of this user
guide.
Shier Adjustment
Adjustment - Front Derailleur: (Figure 18)
1. Shi the rear shier to the smallest number indicated, then shi the front shier to the
smallest number indicated. Disconnect the front derailleur cable from the cable anchor
bolt and place the chain on the smallest chainwheel.
2. Ensure the front derailleur cage is parallel with the outer chainwheel on the crankset.
There must be a 3 - 5mm gap between the bottom of the derailleur cage and the top of
the outer chainwheel teeth to ensure the derailleur will clear the chainwheel when
shiing.
3. Adjust the low limit screw so the chain is centered in the middle of derailleur cage. Pull
all slack out of the cable by pulling it taut, then reconnect the cable and tighten the
cable anchor bolt securely.
4. Shi the front shier into the largest gear and pedal the bike so the chain jumps to the
largest chainwheel. If the chain does not shi onto the largest chainwheel, you will need
to turn the high limit screw counter-clockwise until the chain moves to the largest
chainwheel. If the chain falls into the pedals, the high limit screw has been turned too
far. You will need to readjust the high screw clockwise in 1/4 turn increments until the
chain no longer falls off.
5. Shi through each gear ensuring all are achieved quietly and without hesitation. Some
shiers may have an adjusting barrel. Use the adjusting barrel to fine tune the
adjustment of the chain location. Turn the adjusting barrel clockwise will move the
derailleur inboard - towards the frame, while turning it counterclockwise will direct the
chain outboard - away from the frame.
WARNING: Do not operate a bicycle that is not shiing properly. Overlooking
proper adjustments may cause irreparable damage to the bicycle and/or bodily
injury. Never move the shier while pedalling backward or pedal backward aer
having moved the shier. Doing so may jam the chain and cause serious damage
to the bicycle and/or rider.
Figure 18
Lubrication
All the pivoting points of the front and rear derailleurs should be lubricated with light oil at
least once a month. Be sure to wipe off any excess oil to prevent attraction of dirt into the
mechanisms. The shiing cables should be cleaned and re-coated with a thin layer of
grease every 6 months, or whenever new cables are being installed.
Adjustment - Rear Derailleur: (Figure 19 & 20)
The Low limit screw determines how far the rear derailleur will travel toward the wheel of the
bicycle, while the High limit screw determines how far the cage will travel toward the frame.
1. Shi the rear shier to the largest number indicated, disconnect the rear derailleur cable
from the cable anchor bolt and place the chain on the smallest sprocket.
2. Adjust the High limit screw so the chain and the smallest sprocket are lined up
vertically. Remove any slack in the cable by pulling it taut, then reconnect the cable
and tighten the cable anchor bolt securely.
3. Some derailleurs have an adjusting barrel (see drawings). Use the adjusting barrel to
fine tune the adjustment of the chain location. Turning the adjusting barrel clockwise
will move the derailleur inboard - towards the wheel - while turning it counterclockwise
will direct the chain outboard - away from the wheel.
4. Shi the chain onto the largest sprocket; adjust the low limit screw so the chain and the
largest cog are lined up vertically. If you are unable to get the chain to the largest cog,
turning the Low limit screw counterclockwise will enable the chain to move towards the
wheel.
5. Shi through the gears ensuring each gear is achieved quietly and without hesitation.
Outer side of Top Gear
Figure 19
Figure 20
Note:
Some bicycles may be equipped with a rear derailleur mechanism that works in
REVERSE to the directions above.
MAINTENANCE
Lubrication
Lubrication should be performed by a qualified bicycle mechanic for the parts to be
disassembled. The information provided in this user guide about the service is for only those
who are comfortable doing the maintenance.
The following are examples of the type of service you should perform yourself. All other
service, maintenance and repair should be performed in a properly equipped facility by a
qualified bicycle mechanic using the correct tools and procedures.
Break-in Period:
Your bike will last longer and work better if you break it in before riding it hard. Control
cables and wheel spokes may stretch or “seat” when a new bike is first used and may require
readjustment by your local bicycle repair shop. The Safety Checklist section of this user
guide will help you identify the things that need readjustment.
Aer every long or hard ride:
if the bike has been exposed to water or grit; or at least every 160km: Clean the bike and
lightly lubricate the chain's rollers with a good quality bicycle chain lubricant. Wipe off
excess lubricant with a lint free cloth. Lubrication is a function of climate. Talk to your local
bicycle shop about the best lubricants and the recommended lubrication frequency for your
area. Avoid contaminating the rims with lubricant!
Aer every long or hard ride or aer every 10 to 20 hours of riding:
• Squeeze the front brake and rock the bike forward and back. Everything feel solid? If
you feel a clunk with each forward or backward movement of the bike, you probably
have a loose headset. Have your local bike shop check it.
• Li the front wheel off the ground and swing it from side to side. Feel smooth? If you feel
any binding or roughness in the steering, you may have a tight headset. Have your local
bike shop check it.
• Grab one pedal and rock it toward and away from the centerline of the bike; then do the
same with the other pedal. Anything feel loose? If so, have your local bike shop check it.
• Take a look at the brake pads. Starting to look worn or not hitting the wheel rim
squarely? Time to have the local bike shop adjust or replace them.
• Carefully check the control cables and cable housings. Look if any rust, kinks, or fraying
has occurred and if so, have your local bike shop replace them.
• Squeeze each adjoining pair of spokes on either side of each wheel between your
thumb and index finger. Do they all feel the same? If any feel loose, have your local bike
shop check the wheel for tension and trueness.
• Check the tires for excess wear, cuts or bruises. Have your local bike shop replace them
if necessary.
• Check the wheel rims for excess wear, dings or dents and scratches. Consult your local
bike shop if you see any rim damage.
• Check to make sure that all parts and accessories are still secure, and tighten any
which are not, including but not limited to pedals, crank arms, chains, seat post, and
handlebars.
• Check the frame, particularly in the area around all tube joints; the handlebars; the
stem; and the seat post for any deep scratches, cranks or discoloration. These can be
signs of stress-caused fatigue and indicate that a part is at the end of it's useful life and
needs to be replaced.
Service Checklist:
Frequency
Weekly
Monthly
6 Monthly
Yearly
Note:
The frequency of maintenance should increase with lots of usage and use in
wet or dusty conditions. Do not over lubricate - remove excess lube to prevent
dirt build up. Never use a degreaser to lubricate your chain.
Component
• Chain
• Derailleur wheels
• Derailleur
• Brake callipers
• Brake levers
• Shi levers
• Freewheel
• Brake callipers
• Bottom bracket
• Pedals
• Derailleur cables
• Wheel bearings
• Headset
• Seat pillar
Lubricant
• Chain lube or light oil
• Chain lube or light oil
• Oil
• Oil
• Oil
• Lithium based grease
• Oil
• Lithium based grease
• Lithium based grease
• Lithium based grease
• Lithium based grease
• Lithium based grease
• Lithium based grease
• Lithium based grease
How to Lubricate
• Brush or squirt on
• Brush or squirt on
• Oil can
• 3 drops from oil can
• 3 drops from oil can
• Disassemble
• 2 drops from oil can
• Disassemble
• Disassemble
• Disassemble
• Disassemble
• Disassemble
• Disassemble
• Disassemble
WARNING: Like any mechanical device, a bicycle and its components are subject
to wear and stress. Different materials and mechanisms wear or fatigue from stress
at different rates and have different life cycles. If a component’s life cycle is
exceeded, the component can suddenly and catastrophically fail, causing serious
injury or death to the rider. Signs of stress - caused fatigue indicate that a part is at
the end of it’s useful life and needs to be replaced.
OUBLESHOOTING
TR
Gears/Chain:
Problem
Gear shis not working
properly.
Slipping chain.
Chain jumping off
freewheel sprocket or
chain ring
Component
• Derailleur cables sticking or
stretched or damaged.
• Front or rear derailleur not
adjusted properly.
• Indexed shiing not adjusted
properly
• Excessively worn/chipped
chain ring or freewheel
sprocket teeth.
• Chain worn/stretched.
• Stiff link in chain.
• Non-compatible chain,
chain ring or freewheel.
• Chain ring out of true.
• Chain ring loose.
• Chain ring teeth bent or
broken.
• Rear or front derailleur sideto-side travel out of
adjustment.
Lubricant
• Lubricated, tighten, or replace
cables.
• Adjust derailleurs.
• Adjust indexing.
• Replace chain ring, sprockets
and chain.
• Replace chain.
• Lubricate or replace link.
• Seek advice at bicycle shop.
• Re-align if possible or replace.
• Tighten mounting bolts.
• Repair or replace chain ring
/set.
• Adjust derailleur travel.
Pedals:
Problem
Constant clicking
noises when pedalling.
Grinding noise when
pedalling.
Freewheel does not
rotate.
Brakes:
Problem
Brakes not working
effectively.
Cause
• Stiff chain link
• Loose pedal axle or bearing.
• Loose bottom bracket axle or
bearings.
• Bent bottom bracket bearings
too tight.
• Loose crankset.
• Pedal bearings too tight.
• Bottom bracket bearings too
tight.
• Chain fouling derailleurs.
• Derailleur jockey wheels dirty
or binding.
• Freewheel internal pawl pins
are jammed.
Cause
• Brakes blocks worn down.
• Brakes blocks/rim greasy, wet
or dirty.
• Brake cables are binding,
stretched or damaged.
• Brake levers are binding.
• Brakes out of adjustment.
Solution
• Lubricated chain or adjust
chain link.
• Adjust bearings or axle nut.
• Adjust bottom bracket.
• Replace bottom bracket
axle or pedals.
• Tighten crank bolts.
• Adjust bearings.
• Adjust bearings.
• Adjust chain line.
• Clean and lubricate jockey
wheels.
• Lubricate, if problem
persists, replace freewheel.
Solution
• Replace brake blocks.
• Clean blocks and rim.
• Clean, adjust or replace
cables.
• Adjust brake levers.
• Centre brakes.
When applying the
brakes they
squeal/squeak.
Knocking or shuddering
when applying brakes.
• Brake blocks worn down.
• Brake block toe-in incorrect.
• Brake blocks/rim dirty or wet.
• Brake arms loose.
• Bulge in the rim or rim out of
true.
• Brake mounting bolts loose.
• Brakes out of adjustment.
• Fork loose in head tube.
• Replace blocks.
• Correct block toe-in.
• Clean blocks and rim.
• Tighten mounting bolts.
• True wheel or take to bike
shop.
• Tighten bolts.
• Centre brakes and/or adjust
brake block toe-in.
• Tighten headset.
Wheels/Tires:
Problem
Wobbling wheel.
Steering not accurate.
Frequent punctures.
Cause
• Axle broken.
• Wheel out of true.
• Hub comes loose.
• Headset binding.
• Hub bearings collapsed.
• Quick release mechanism
loose.
• Wheels not aligned in frame.
• Headset loose or binding.
• Front forks or frame bent.
• Stem wedge bolt not tight.
• Inner tube old or faulty.
• Tire tread/casing worn.
• Tire unsuited to rim.
• Tire not checked aer previous
puncture.
• Tire pressure too low.
• Spoke protruding into rim.
Solution
• Replace axle.
• True wheel.
• Adjust hub bearings.
• Adjust headset.
• Replace bearings.
• Adjust QR mechanism.
• Align wheels correctly.
• Adjust/tighten handset.
• Take bike to a bike shop for
possible frame realignment.
• Tighten stem bolt until stem
and fork are unified, Use the
“between the knee” test and
if loose, tighten stem bolt
until it passes test.
• Replace inner tube.
• Replace tire.
• Replace with correct tire.
• Remove sharp object
embedded in tire.
• Correct tire pressure.
• File down spikes.
NOTES
NOTES
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com
Loading...