Formech Compac Mini, Compact Mini Installation, Operating And Service Manual

11

Compac Mini

.

.

.

Installation, Operating and Service Manual

Desktop Vacuum

Forming Machine

For Parts, Service & Technical Assistance

Telephone: [phone]

Fax: [phone]

Manual - Formech Compac Mini

2

Table Of Content

Safety 3

Introduction and initial assembly 4

General Arrangement 5

Machine footprint 5
Electrical Specifications 6
Transportation / Positioning 6
Noise emissions 6
Machine storage 6
Mechanical Specifications 6
Machine arrangement 7
Reducing Windows (optional) 9

Operating Procedure 10

Operating Techniques 12

Optional Extras 13

Tools 14

Plastics 16

Post Forming Operations 17

After forming 17
Trimming 17

Warranty 18

Seals 18
Heating elements 18
Vacuum system 18

Service / Repair 19

Replacing seals 19
Replacing a heating element 20
Electrical troubleshooting 24
Vacuum / Pressure System 27
Cleaning 29
Lubrication 29

Spare Parts Listing 30

Wiring Diagram Formech Mini 31

Vacuum Pump D351VM 32

EC Machinery Directive 34

Manual - Formech Compac Mini

3

Thank you for choosing Formech.

Please read and follow the below safety instructions before attempting to install or operate your machine.

> Do not operate the machine until you have been trained and are fully conversant with it.
> Read and understand all of this user manual.
> This is a ‘single person operating’ machine.
> Check your supply voltage and frequency. Make sure it is compatible with your machine. Your machine’s

electrical specification is on the plate on the right hand side.
> You must ensure that the machine is properly earthed and fused.
> If your machine is not equipped with a moulded mains connector then note that:
The earth wire is GREEN with a YELLOW stripe.
The live wire is BROWN
The neutral wire is BLUE
> Only suitably qualified personnel should make electrical connections
> Turn off the machine and disconnect the power supply when the machine is not in use.
> The heater and pump on this model are not intended to be left running indefinitely.
> Never remove any panels unless the electrical supply has been isolated.
> Always let the machine cool down before attempting to work on it. Some parts of the heater and heat
shield become extremely hot during operation.
> Note the safety warning labels situated on the front and rear panels. Never remove any warning labels
from the machine.
> Note the ‘HOT SURFACES’ safety labelling on the heater & heater guard. These areas can become VERY
HOT.
> Only use the machine for vacuum forming plastic. It is not intended for any other purpose.
> Ensure that the area you are working in is properly ventilated and that you are aware of the potential

hazards from the plastics you are forming. It is the responsibility of the owner or designated responsible
person to assess the risks associated with any dangerous fumes given off and to determine any necessary
precautions required such as fume extraction. Contact your plastics supplier to gain information regarding

hazardous fumes.
> There is a risk of being burnt when handling heated plastics. Always wear suitable personal protective

equipment such as gloves.
> Ensure that the area surrounding the machine is clean and frequently cleared of finished product and any
scrap.
> This machine is fitted with a dry running vacuum pump. Do not lubricate. Do not allow any liquid to en-

ter the vacuum system. Ensure that moulds are properly sealed to prevent ingress of dust into the vacuum
circuit. Severe damage may be caused if the above is not observed.

> Daily repetitive use of this or any other machine may lead to a) fatigue and loss of concentration b) pos­sible strains.
> Operators should be trained in the use of correct lifting techniques in order to minimise these effects.
> Users of this machine should complete regular competence tests.

Safety

Manual - Formech Compac Mini

4

Introduction and initial assembly

Your Formech machine is supplied with:

1x Electrical cable 1x Installation/Operations/Repair

Manual

1x EC Certificate of Conformity 1x Table Mesh

4

Compac Mini

.

.

.

Installation, Operating and Service Manual

Desktop Vacuum
Forming Machine

For Parts, Service & Technical Assistance

Telephone: [phone]

Fax: [phone]

EC Machinery Directive

2006/42/EC

Declaration of Conformity

We hereby certify that the machinery stipulated below complies with all the relevant provisions
of the EC Lachinery Directive and the National Laws and regulations adopting this Directive
Modifictions to this machinery without prior approval from the undersigned will render this
declaration null and void.

Machine description: Vacuum Forming Machine
Machine Function: Thermoforming of Plastic Sheet
Model/Type: Compac Mini
Serial Number:
Date of Manufacture:

Is in conformity with the provisions of the following other EC Directives:

2004 / 108/EC - EMC
2006 / 95/EC - LVD

Technical File Compiled by: Andrew Berry at address below

Significant harmonised standards applied:

EN ISO 12100 : 2010
EN ISO 13849 : 2006
EN 60204 - 1 : 2006
EN 12409: 2008

Signed:

Date:
Name: Paul Vukovich
Position: Managing Director
Being the responsible person appointed by the manufacturer

ENSURE THAT THE TABLE LEVER IS TIGHTLY SCREWED INTO THE CRANK MECHANISM ON THE
RIGHT HAND SIDE OF THE MACHINE. IF OPERATED WITH THE LEVER LOOSENED YOU MAY
DAMAGE THE CRANK OR THE HANDLE.

Manual - Formech Compac Mini

5

General Arrangement

Machine footprint

(Dimensions are in mm)

439.40

835

360 383

425

703

250

Power inlet socket

Manual - Formech Compac Mini

6

General Arrangement

1- Specification Plate
2- Power Inlet (EC)
3- Power Switch ON/OFF
4- Clamp Frame
5- Material Clamps
6- Heater Box
7- Vacuum / Pressure Valve
8- Table Lever
9- Digital timer
10- Vacuum Pump ON/OFF switch
11- Vacuum Gauge

Mechanical Specifications

Max Material Size: 305mm x 255mm
Max Forming Area: 280mm x 230mm
Max Depth of Draw: 125mm
Overall Width: 440mm
Overall Height: 425mm
Overall Length: 835mm
Weight: 35Kg

Electrical Specifications

Standard Voltage: 208V-240V ac
Frequency: 50-60Hz
Power: 1.1Kw

Compac Mini

7

8

9

10

6

11



6

2

1

4

5

3

Transportation / Positioning

The Compac Mini will be supplied strapped to a Pallet or in a crate. The machine may be unpacked and
placed on a bench, table or Compac Mini trolley. Ensure that the structure, size and load bearing capacity
of the bench or table is sufficient for the machine weight. A minimum of 2 persons are required to lift the
machine. In the case of the Compac Mini trolley, ensure that the 2 machine retaining screws are fitted to the
under side of the trolley / Machine.

Noise emissions

Noise emissions on the Formech Compac Mini are less than 70dB(A).

Machine storage

The Formech Compac Mini must be stored in a dry environment. If the machine is not used for a long period
of time, run the pump periodically (once a month).

Manual - Formech Compac Mini

7

General Arrangement

Machine arrangement

1. Specification Plate.

This states the essential machine data & CE marking.

2. Power Inlet receptacle.

The machine is supplied complete with a power cable that plugs into this receptacle and then into a suitable
power socket. If your machine is a special voltage or frequency then it may be supplied with a lead not termi­nated into a mains plug. See Safety section at the beginning of this manual. Note the safety labelling.

3. Power Switch ON/OFF.

This is the main switch. When in the OFF position power is cut to all functions. Before commencing any re­pair work always remove the mains lead from the Power Inlet Receptacle.

4. Clamp Frame.

This holds the plastic material in position during the forming and release processes.

5. Material Clamps.

These clamps fix the Clamp Frame firmly down. After placing the plastic under the clamp frame the material
clamps are adjusted by tightening or loosening the blue nutlets. The levers are pulled up until they are fully
over-centre. Adjustment may only be carried out while not under pressure. The rear of the clamp frame is self
adjusting.

6. Heater Box.

This carries the heating elements and is drawn forward by pulling the centrally mounted handle.

7. Vacuum/Pressure Valve.

When the vacuum pump is running this valve switches between removing air from between the mould and
moulding during forming (vacuum) and introducing air between the mould and moulding for finished part
release (pressure).

8. Table Lever.

When pulled towards you the table will rise to the upper limit. A further application of pressure will lock the
table in this position. During forming the table complete with mould is lifted into the hot plastic and locked
in place to ensure a good vacuum seal. At the end of the cycle the table is returned to the lower position by
pushing the handle back and away.

NOTE: A mechanical interlock designed to prevent a mould being raised into the heating elements
stops the table being raised unless the heater box is fully back.

Manual - Formech Compac Mini

8

General Arrangement

Machine arrangement (continuation)

9. Digital Timer.

When producing a quantity of mouldings using the same mould and plastic the heating time will be nearly
constant for each one. In this case the timer can be used. Record the heating time for the first moulding then
set the timer (in seconds) using the UP / DOWN buttons. When the heater is pulled forward the timer counts
down from the set time and sounds a buzzer when zero is reached. The heater is then pushed back. The set
time is stored until it is altered. If you don’t want to use the timer, set the time to zero.

10. Vacuum Pump ON/OFF switch.

This turns the vacuum pump on and off. The vacuum pump evacuates the air between the plastic sheet and
the mould. It also provides pressure to release the finished moulding from the mould.

11. Vacuum Gauge.

This is situated on the top LHS of the front panel and gives indication of the vacuum level achieved at the
table mould area during moulding. It is usual to expect approx 20”Hg / -680mbar of vacuum. If such levels
are not achieved check your mould / table configuration & clamp / plastic sealing.

Manual - Formech Compac Mini

9

General Arrangement

Reducing Windows (optional)

Reducing windows allow the use of smaller sheet material for smaller mouldings. To fit the reducing window:

1. Lift the clamp frame and place the lower
reducing window.

2. Locate the window against the clamp frame.

3. Place the upper reducing window in the clamp
frame at the rear.

4. Then locate it at the front of the clamp frame.

5. Fit the bolt and the nut to secure the window
to the clamp frame.

6. Reducing windows correctly fitted
to the machine.

Manual - Formech Compac Mini

10

Operating Procedure

Basic Operation

1. Press the power switch to ON. The digital timer
on the front panel will illuminate. It usually takes

between 10 and 15 minutes before the heaters

have reached their operating temperature.

2. With the heater fully back and the mould table
in the up position place your mould onto it.

3. Place the table into the lower position by
pushing the table lever away from you.

4. Position a sheet of plastic over the aperture.

The plastic should be placed over the white seals

around the aperture.

5. Pull the clamp frame down and close the mate­rial clamps. Depending on the plastic thickness,

you may need to adjust the screws on the mate-

rial clamps to properly grip the plastic.

6. Set the timer down to zero using the ‘Down’

button to help you establish the time for the hea-

ting cycle. If you know the cycle time, then press

the ‘Up’ button to the right time.

Manual - Formech Compac Mini

11

Basic Operation (continuation)

Operating Procedure

7. Pull the heater forward over the plastic. As the

plastic heats up, it will begin to rise slightly. It will

then soften and begin to drop back.

8. Push the heater back slightly to test the softness
of the plastic. Be careful the plastic might be very

hot. Continue to heat until it is soft enough to form.

9. Turn on the vacuum pump and raise the table

until you can feel it lock into place. The plastic will

form around the mould tool.

10. Let the finished moulding cool down a little
before pulling the release valve downwards to

blow the part off the tool. Lower the table and

switch off the vacuum.

11. If the plastic is still too soft when you try to

release it, some distortion may occur. Make sure

the mould is not stuck in the moulding when

you lower the table.

12. Finally, release the material clamps to remove
the finished moulding.

Manual - Formech Compac Mini

12

Operating Techniques

Heaters

The powerful quartz heaters are designed to heat the plastic rapidly without burning the surface. The time
required to heat the plastic sheet remains fairly constant once the heaters have reached their operating
temperature.

Heating cycle times vary according to a number of factors. With a little experience, timings may be easily
estimated.

Some plastics such as styrene have a wide tolerance to heating times giving consistently good mouldings.
Care must be taken with other materials such as ABS, as the surface will blister if the temperature limit is
exceeded.

The moulding should be formed when the plastic is sufficiently relaxed to become indented by the blunt end
of a pencil but not soft enough to sag.

A properly heated sheet will give an excellently defined moulding. If the sheet is not hot enough while for­ming the moulding will not pick up all the detail from the tool.

The times below were recorded using styrene at an ambient temperature of 20 degrees C
With the machine at operating temperature. Please note that these times are a guide only.
Various factors will affect the heating time including the colour and surface finish of the material.

1.5mm Thick = 60 seconds

2.0mm Thick = 95 seconds

4.0mm Thick = 240 seconds

Digital Timer - When producing a quantity of mouldings using the same mould and plastic the heating time
will be nearly constant for each one. In this case the timer can be used. Record the heating time for the
first moulding then set the timer (in seconds) using the UP / DOWN buttons the buttons. When the heater
is pulled forward the timer counts down from the set time and sounds a buzzer when zero is reached. The
heater is then pushed back. The set time is stored until it is altered. If you don’t want to use the timer, set
the time to zero.

Manual - Formech Compac Mini

13

Optional Extras

1. Service kit 2. Reducing windows

3. Compac Mini trolley

The following items can be purchased for your Compac Mini vacuum forming machine:

1. It is unlikely that you will need to service or repair your machine for many years provided you follow the
maintenance information contained in this manual; however the table and clamp seals, which are conside­red to be consumable items, will need to be replaced depending on the usage of the machine. Therefore
this kit contains the essential consumables (seals and pump filter) to ensure a good performance of your
machine year on year.

2. Formech has available a standard size of reducing windows: 5x4’’ or 125x100mm aperture. Formech can
also produce special size reducing windows. For more information please contact our sales department.

3. The Formech machine trolley allows you to easily move your Compac Mini machine. The 2 locking castors
assure the trolley remains in position all the time. Underneath there is also space to store plastic material
and moulds. The trolley dimensions are: depth: 760mm, height: 720mm, width: 460mm

Manual - Formech Compac Mini

14

Tools

All tools should be mounted on a baseboard. They should not have undercuts and must be produced with
slightly angular sides (‘draft angle’) to aid release. Vent holes are needed to allow the air to be evacuated
from pockets and sharp angles on the tool. Providing these holes are kept small (1mm diameter or less) they
will not leave marks on the surface of the finished moulding.

Tools made from wood or medium density fibreboard (MDF) are easily constructed and can give short runs
of good quality mouldings at a low cost (see notes page 16). The use of close-grained wood will avoid grain
patterns appearing on the mouldings.

Plaster of Paris may be used for one-offs but the plaster must be allowed to properly dry out. (See notes
below)

Aluminium tools have the advantages of carrying fine detail and being more resistant to both distortion and
surface damage. Aluminium tools should be pre-heated before use. A cool metal mould will absorb some of
the heat from the plastic sheet before it can take up the full definition.

Resin tools combine most of the advantages of metal moulds with relative ease of manufacture. Various resi­nous materials are commercially available especially for vacuum forming tool production.

Repairs to the vacuum circuit can be costly. The use of talc as a release agent is not recommended.
It may clog the vacuum pump, valves and hoses.

MDF Baseboard

Aluminium Baseboard

Manual - Formech Compac Mini

15

Tools

NOTES:

Porous mould materials such as wood and plaster should be properly sealed to prevent the vacuum pump
from sucking out any moisture or sawdust, loose plaster etc. The vacuum circuit may quickly become blocked
with dust or slurry if moulds are not properly sealed.

As the plastic cools after forming it will contract, gripping the tool tightly. If the tool has been made with
sloping sides and has a good surface finish it will release more easily. Where the draft angle must be kept to
a minimum a release agent may be used to assist release.

Sealed moulds will usually release more easily. Silicon based release agents may be used on more difficult
moulds. Silicon based release agents are rapidly absorbed by porous (unsealed) moulds, rendering them
ineffective.

The baseboard can be made from either MDF or aluminium and needs to be 3.00 – 4.00mm (1/8”) thick.
The vacuum hole can be 19.00 – 20.00mm (3/4”) diameter and needs to be positioned 15mm forward of
the centre of the table.

19-20mm

15mm

The baseboard has to be 4mm shorter in
both directions than the forming aperture
of the machine e.g. Forming aperture
280mm x 230mm = baseboard size
276mm x 226mm.

Manual - Formech Compac Mini

16

Plastics

Plastic sheet is commercially available in a wide variety of grades, thickness and colours. Materials such as
styrene and PVC are most suited to vacuum forming. Other materials such as acrylic, polypropylene and
polycarbonate will mould but difficulties may be encountered.

It is not within the scope of this manual to attempt to list all the potential problems and their solutions. It is
recommended that the newcomer to vacuum forming gains experience and confidence with easily formed
materials before moving onto the more difficult materials.

Formech has available a Vacuum Forming Guide which will cover some of these topics in more details. Please
contact Formech to gain access to this guide.

Manual - Formech Compac Mini

17

After forming

After forming, most plastics can be subsequently heat formed to add such details as folds or clips. Although
many plastics can be printed, and in some cases painted, the presence of release agent used to help free a
tight moulding may make the surface resistant to further decoration.

Trimming

An ideal moulding will be ready for use when removed from the machine and requires no finishing. However,
most mouldings do require trimming before they can be used.
There are numerous methods available for this process.

Thin materials can be trimmed with a sharp knife. Shaped cutting dies can be used to cut out intricate
shapes. If no flange is required on the finished product then a trimming saw mounted in a pillar drill will cut
the moulding in a horizontal plane to free it from the surrounding material.

In mass production environments the range of equipment available for this requirement encompasses
clicking presses, roller presses, routers, horizontal band saws, water jet cutters, laser cutters and many others.

Formech has available a Vacuum Forming Guide which will cover some of these topics in more details. Please
contact Formech to gain access to this guide.

Post Forming Operations

Manual - Formech Compac Mini

18

Warranty

Reliability and a long service life are synonymous with the Formech brand. However, as with any machinery,
certain parts will require periodic replacement.

Seals

The silicon seals applied to the mould table and to the top aperture of the machine (clamp) are seen as
being consumable parts, their service life will depend on how the machine is treated and how often it is used.

The table and clamp seals are not covered by our warranty.

Heating elements

The Quartz infrared heating elements supplied with this machine are manufactured using quartz tube and
therefore may break or crack with impact or physical shock.
The Quartz heating elements contain internal filaments, which become extremely hot when power is applied.
The wire expands and contracts as it heats and cools.
Eventually, due to the continual expansion and contraction, the wire will fracture and a new element will be
needed. This may take 10 years or more. Because of this we are unable to apply our standard warranty to
Quartz heating elements. However our experience is that this form of infrared heating is durable, reliable and
more resilient to shock and impact than similar ceramic products

The heating elements are not covered by our warranty.

Vacuum system

The vacuum system on this machine is fairly simple but uses high quality components throughout. The life
expectancy of the vacuum system will be compromised by the ingress of dirt, shavings, dust, liquid etc.

THE VACUUM CIRCUIT INCLUDING THE VACUUM PUMP WILL NOT BE COVERED BY OUR WARRANTY IF
THEY ARE FOUND TO BE BLOCKED WITH FOREIGN MATTER OR CORRODED BY THE INGRESS OF LIQUID.

Manual - Formech Compac Mini

19

Replacing seals

Clean up completely,
mask the area and ‘key’
the surface.

Apply the sealant
evently.

Fit overlapping silicone
strips and ‘bed’ into
sealant.

Apply a 45 degree mitre
at the corners. Ensure
the joint is sealed.

1

2

3 4

1. Remove all the existing seal and adhesive with a sharp blade. Mask off the sealing area with masking tape

or similar (Mask the outside for top frames or reducing windows & the inside for table seals). Prepare the
sealing area with emery cloth or similar to achieve a good surface for the new adhesive to key with. Ensure
that the surface is clean from dust, dirt and grease.

2. Apply a generous bead of high modulus silicone sealant to the masked area and smooth down to give a
consistent layer.

3. Cut the silicone strip in lengths long enough to overlap the corners. Do not stretch the seal strip when
measuring or applying. Lay each strip on to the seal area overlapping at the corners. Ensure the seal strip is
bedded down well by pressing firmly along the full length.

4. With a sharp blade cut a 45° mitre joint at all corners. Fill gaps in the joints with sealant. Remove the
masking tape before the sealant has set. For best performance leave seal to set overnight.

Service / Repair

Manual - Formech Compac Mini

20

Service / Repair

Replacing a heating element

1- Unplug the machine from the

mains. Bring the heater completely

forward and remove the fours screws

retaining the cover.

2- Remove the cover on top of the heater.

Before any maintenance work is carried out, electrical supply must be locked in the OFF position
or the mains lead removed.

Only a qualified electrical technician may work on any parts carrying mains voltage and should be
responsible for ensuring that the machine is in a safe condition before allowing services to be res­tored.

If the plastic is not being heated evenly and there is an obvious cold spot then follow the below
procedure.

> Switch off machine and let heater cool completely, this will take at least 15 minutes.

> Bring the heater half way forward, place hand near but not on elements

to see if they are still hot. If they are, let machine cool for a further 15 minutes.

> When elements are completely cool, turn on machine and feel each element individually.

The difference in temperature will quickly become noticeable. If one or more elements fail to heat
then follow below.

Manual - Formech Compac Mini

21

Service / Repair

Replacing a heating element (continuation)

7- Bring the heater forward and remove the

cap from the terminal block associated with the

faulty element using a cross head screw driver.

8- Loosen and remove the element wires

from the appropriate connector block.

5- To do so, loosen/remove the two screws

at the back of the machine.

6- Then, send the heater back to be able to

remove the two screws of the heater bars at

the front of the machine.

3- At this stage, check that all the element

wires and interconnecting wires are fully

tightened and that the fault wasn’t merely

a loose connection.

4- Remove the two nuts and washers that

secure the element to the tray. At this stage

you might have to loosen the heater tray to

be able to catch the faulty element.

Manual - Formech Compac Mini

22

Service / Repair

Replacing a heating element (continuation)

11- Carefully lift the heater tray. This might

be a two person job.

12- Feed the element wires through the
holes in the tray and catch the element.

13- Fit the new element. 14- Replace the two nuts and washers that

secure the element to the tray.

9- Remove the loose insulation sleeves. 10- Position your hand underneath to catch

the element as it is released.

Manual - Formech Compac Mini

23

Service / Repair

Replacing a heating element (continuation)

17- Put back the two screws from the heater bars and tighten.

18- Replace the terminal block cover and

make sure all is fully tightened.

19- Tighten the two screws at the back of

the machine and make sure that the two

bars are correctly lined up with the back of

the machine.

15- Put back the loose insulation sleeves. 16- Replace the element wires in the connec-

tor block and tighten all connections surely.

Manual - Formech Compac Mini

24

Service / Repair

Electrical troubleshooting

In the event that neither the heater nor the pump will work check that your supply is OK.

Check the fuse located under the IEC inlet socket on the left of the machine. A spare is fitted in the small
plastic fuse holder. The fuse is a standard 20mm x 5mm glass fuse. It is rated at 5 Amps.

If neither the fuse nor the mains supply are faulty then turn off the machine. Unplug the machine from the
mains and remove the iec plug from the side of the machine and follow below:

IEC inlet socket on the left of the machine. Spare is fitted in the small plastic fuse holder.

Remove the 6 self-tapping screws retaining the rear panel.

Before any maintenance work is carried out, electrical supply must be locked in the OFF position
or the mains lead removed.

Only a qualified electrical technician may work on any parts carrying mains voltage and should be
responsible for ensuring that the machine is in a safe condition before allowing services to be res­tored.

Manual - Formech Compac Mini

25

Service / Repair

Electrical troubleshooting (continuation)

Check that the connectors on the back of the IEC socket are properly

fixed. See wiring diagram if any have fallen out.

If the fault still cannot be found, then check the front of the machine:

Remove the 4 self-tapping screws retaining the

front panel.

Remove the 2 self-tapping screws on each side of

the machine.

Before any maintenance work is carried out, electrical supply must be locked in the OFF position
or the mains lead removed.

Only a qualified electrical technician may work on any parts carrying mains voltage and should be
responsible for ensuring that the machine is in a safe condition before allowing services to be res­tored.

Manual - Formech Compac Mini

26

Service / Repair

Electrical troubleshooting (continuation)

Before any maintenance work is carried out, electrical supply must be locked in the OFF position
or the mains lead removed.

Only a qualified electrical technician may work on any parts carrying mains voltage and should be
responsible for ensuring that the machine is in a safe condition before allowing services to be res­tored.

Note: Continuity should be obtained between the top and bottom contacts of the switch not side to side.

If the vacuum pump motor does not run, check the electrical supply. If the motor smells strongly of burnt
lacquer then it is probably burnt out and the entire pump/motor assembly needs replacing.

If the supply is present but the motor does not run, the capacitor may be faulty.

Check the pump switch connections if the pump only is the problem. If all the connections are good then

the switches can be checked for continuity.

Manual - Formech Compac Mini

27

Vacuum / Pressure System

If the vacuum or pressure appears to be weak or non-existent check the following.

Service / Repair

The possible causes of poor vacuum are:

• The mould baseboard is restricting the vacuum hole in the table.

• NOTE: If the mould baseboard is too soft it may pull down under vacuum and block the vacuum hole.

• The mould is inadequately vented to allow trapped air to be evacuated.

• The table and clamp seals are in poor condition or the table is not locking properly at the top of its travel.

• There are holes drilled in the table.

If all the above points are OK and you can hear the pump running when you switch it on then one of the fol­lowing points will be the cause of the problem. If the pump does not run, refer to the ELECTRICAL TROUBLE
SHOOTING section above.

• A pipe is loose, damaged or blocked.

• The pump filter is blocked

• The vacuum/pressure valve is blocked or corroded.

• The vacuum pump is blocked or corroded.

Raise and lock the mould table in the up position. Take off the table mesh.

If the vacuum gauge reads 20”Hg or higher

that is normal. A lower reading indicates

poor vacuum where attention is required.

Turn the vacuum on and place your finger

over the vacuum hole. Check the reading you

get on the vacuum gauge.

Manual - Formech Compac Mini

28

If the heater has been left in the forward position, with no plastic in the clamp frame, the table will start to
overheat. The pipe attached to the back of the table will shrink and constrict the passage of air. Pipes beco­me less flexible over time and may loosen or crack.

To check the vacuum filter:

Service / Repair

Unplug the machine from the mains and remove the iec plug from the side of the machine.

Remove the 6 self-tapping screws securing the back panel.

You will see the cylindrical vacuum filter with a pipe attached to each

end. Discard the blocked filter and fit a new one.

Before any maintenance work is carried out, electrical supply must be locked in the OFF position
or the mains lead removed.

Only a qualified electrical technician may work on any parts carrying mains voltage and should be
responsible for ensuring that the machine is in a safe condition before allowing services to be res­tored.

Vacuum / Pressure system (continuation)

Manual - Formech Compac Mini

29

Service / Repair

Vacuum / Pressure system (continuation)

To check the entire vacuum system:

• Remove the 6 self-tapping screws securing the back panel.

• Remove the nut securing the motor capacitor to the left-hand side of the machine.

• Remove the 2 wires from the capacitor, terminating in the connector block next to the IEC socket.

• Remove all earth wires connected to the earth stud in the base of the machine.

• Remove the 4 nuts attaching the vacuum pump to the base.

• Remove the 6 self-tapping screws attaching the white front panel.

• Remove the 4 self-tapping screws along each bottom side of the machine.

• Rest the machine on its side and remove the 2 self-tapping screws in the base (roughly in the centre).

• Remove the base plate.

• Examine all piping carefully. Replace any suspect pipes.

• Remove the pipes from the vacuum\pressure valve. Take out the 2 fixing bolts.

• Blow through the single hose tail. You should feel air coming out of one hose tail on the opposite side. Ope­rate the valve and air should pass freely through the other hose tail and shut off the first one.

• If the valve does not freely pass air or is otherwise malfunctioning then fit a new one or dismantle and
clean the faulty part.

• If the pump runs but does not appear to produce pressure or vacuum send it back to us for further evalua­tion.

• Reassemble the machine taking great care to ensure that all electrical connections are tight and properly
insulated.

Make certain that the earth stud is tightened fully and that all earth wires are properly fixed to it.

If you are unable to cure any problem relating to your machine, or if you wish to order spare parts please
contact us at the below address, stating the model (Compac mini) the serial No. (on specification plate) and
a full description of the fault or parts you need.

Cleaning

Ensure the inside of the machine and the heater tray is cleared of dust, dirt and debris. Do not allow dirt and
loose particles to build up, particularly on the heater tray.

Lubrication

The Compac Mini requires minimum lubrication.
Apply general purpose grease to the table guide bars when required to assist with table movement.
Apply a small amount of fine silicone oil or fine oil to the heater slide bars when required to assist free move­ment of the heater.

Manual - Formech Compac Mini

30

Spare Parts Listing

Quantity Description Part No

2 Quartz Element 225W FSQ 230V HEQ15

2 Quartz Element 250W FSQ 230V HEQ04

2 Ceramic Terminal Block MPP14

1 Heatproof Cable 1.5mm SiFGL EE41

1 Heatproof Cable 1.5mm, Silicone, G/Y Earth EE67

1 Small Blue Heater Handle GH01

1 Cable Chain EE70

1 Cable Chain End Bracket Set EE71

2 Toggle Clamp Complete, Small Blue MPP19

2 Small Clamp Upper Adjuster Nut Steel M5 MPP27

2 Small Clamp Lower Adjuster Nut Plastic M5 MPP24

2 Mini Clamp Frame Grip, Blue GH29

1 Black Crank Handle Knob GH25

4 Machine Rubber Mounting Foot GH41

1 Mini Table Mesh MPP56

1 Seal kit 'Mini' 5M Seal + Glue SK01

1 Silicone Sealant Cartridge 85ml MPP01

1 Vacuum Pump PAP01

1 40mm Vacuum Panel Mount Gauge P31

1 Small Inline Vacuum Filter PAP04

1 Manual Lever Valve, 5/2, 1/4" Port P01

1 1/4" Bore PVC Reinforced Hose P13

5 1/4" BSPT to 6mm Hose Tail Elbow P22

6 Pipe Clip - Small plastic, Type C P18

1 Paddle Switch (Pump) EE30

1 Timer PCB EE22

1 Microswitch, Hi temp EE34

1 C14 IEC Fused, Switched Socket EE72

1 BS1363/A 3Pin Plug to C13 IEC Power Lead, 5A EE55

1 EU(Shuko) Plug to C13 IEC Power Lead, 5A EE54

1 NEMA6/15(N America) Plug to C13 IEC Power Lead, 5A EE73

Manual - Formech Compac Mini

31

Wiring Diagram Formech Mini

Main L.
(Brown)

Pum p

Feed

(Blu e )

Heater
Supply

(Brown)

Switch Lamp

N.(Blue)

Pum p

Swi tch

Feed

(Brown)

Heater N.

(Bla ck)

Heater

Supply

(Red)

Earth

Stud

Gn/Ylw

Heater

Earth

Stud

Gn/Ylw

Pum p

Feed

(Brown)

Pum p
Cap.1

Pum p
Cap.2

Main N.

(Blu e )

Wiring Diagram FORMECH Compac mini

11

10

1

2

3

5

9

8

7

4

6

KEY

1. IEC Inlet Socket

2. Vacuum Pump

3. Vacuum Pump Cap acitor

4. Main Earth Stud

5. 6 Way Connector Block

6. Heater Earth Stud

7. 150W FSF Heating Element (2 No.)

8. 125W FSF Heating Element (2 No.)

9. Ceramic Connector Block (2 No.)

10. Pum p ON\O FF Switch

11. Mains ON\OFF Illuminated Switch

Pum p

Earth

(Gn.Y lw)

Earth

Stud

Gn/Ylw

KEY

1- IEC Inlet Socket
2- Vacuum Pump
3- Vacuum Punp Capacitor
4- Main Earth Stud
5- 6 Way Connector Block
6- Heater Earth
7- 150W FSF Heating Element (2 No.)
8- 125W FSF Heating Element (2 No.)
9- Ceramic Connector Block (2 No.)
10- Pump ON/OFF Switch
11- Mains ON/OFF Illuminated Switch

Manual - Formech Compac Mini

32

Vacuum Pump D351VM

Features

> Oil free with stainless steel valves
> Good quality, low noise
> Easily changed from pressure to vacuum and vice versa
> All models 240V single phase

Specifications

Model Typical Applications Typical Performance Max Pressure

D351VM Air supply for flame photometer 15l/min at 15psi 8l/min at 30psi

Manual - Formech Compac Mini

33

Typical arrangement

Vacuum Pump D351VM

Manual - Formech Compac Mini

34

EC Machinery Directive

2006/42/EC

Declaration of Conformity

We hereby certify that the machinery stipulated below complies with all the relevant provisions
of the EC Lachinery Directive and the National Laws and regulations adopting this Directive
Modifictions to this machinery without prior approval from the undersigned will render this
declaration null and void.

Machine description: Vacuum Forming Machine
Machine Function: Thermoforming of Plastic Sheet
Model/Type: Compac Mini
Serial Number:
Date of Manufacture:

Is in conformity with the provisions of the following other EC Directives:

2004 / 108/EC - EMC
2006 / 95/EC - LVD

Technical File Compiled by: Andrew Berry at address below

Formech International Limited, Unit 4, Thrales End Farm, Thrales End Lane, Harpenden
Hertfordshire AL5 3NS, United Kingdom

Significant harmonised standards applied:

EN ISO 12100 : 2010
EN ISO 13849 : 2006
EN 60204 - 1 : 2006
EN 12409: 2008

Signed:

Date:
Name: Paul Vukovich
Position: Managing Director
Being the responsible person appointed by the manufacturer

EC Machinery Directive

Manual - Formech Compac Mini

35

For Parts, Service & Technical Assistance UK,

Europe and Rest of the World

Telephone: [phone]

Fax: [phone]

[e-mail]

For Parts, Service & Technic al Assistance North

and South America

Telephone: [phone]

Fax: [phone]

[e-mail]

Formech International Limited
Unit 4, Thrales End Farm, Thrales End Lane, Harpenden, Hertfordshire, AL5 3NS U.K.
Tel: [phone] Fax: [phone]
Email: [e-mail]