Formax Roller Cleaning User Manual
Formax Cleaning Kit
Includes:
(1) Can Formax Rubber Roller Cleaner
(10) Cotton Cloths
Pressure Seal (FD1500, FD2002, FD2032, FD2054):
1. Make sure machine is turned off and unplugged. Lift up top cover and remove upper fold plate. All pressure seal
equipment has four (4) black rubber fold rollers and two (2) steel rollers.
2. Using Formax roller cleaner, spray a new cotton cloth until the cloth is saturated.
forth motion making sure to clean the entire surface of the fold and seal rollers. Now take a dry cloth and wipe off
excess toner. The cloth should be covered with black toner surplus from cleaning the rollers.
3. Make sure to run 10-15 sheets of blank copy paper to ensure all cleaner has been removed from the fold rollers.
Running blank sheets will remove any excess residue of cleaner on the rollers.
Wipe the wet cloth in a back and
Fold Rollers
Seal Rollers
Folders (FD320, FD342, FD382, FD 38X):
1. Make sure machine is turned off and unplugged. All folders have four (4) rubber rollers (FIG A).
2 Remove and unplug (if FD382/FD38X) the upper and lower fold plates (FIG B).
3. Using Formax roller cleaner, spray a new cotton cloth until the cloth is saturated.
forth motion making sure to clean the entire surface of the fold and seal rollers. Now take a dry cloth and wipe off
excess toner. The cloth should be covered with black toner surplus from cleaning the rollers.
4. Make sure to run 10-15 sheets of blank copy paper to ensure all cleaner has been removed from the fold rollers.
Running blank sheets will remove any excess residue of cleaner on the rollers.
Fold Rollers
Wipe the wet cloth in a back and
Upper Fold
Plate
Lower Fold
Plate
FIG A FIG B
Cleaning Procedure for the FD 6102 Series Folder/Inserters
It is important to be familiar with keeping the rubber rollers inside the machine clean. Most issues with these
machines occur when there is an excessive build-up of toner on the rollers that drive the paper through the machine in order to be folded.
The FD 6102 has three (3) fold rollers and a series of smaller transportation rollers, along with rollers in
the feed head. Anything that is rubber and comes into contact with paper MUST be cleaned at some point. The
frequency of cleaning will depend on the usage of the machine as well as the type of toner that you are using.
Recycled Toner may cause the machine to need cleaning more often. Dirty fold rollers will have a “shiny” look
to them, due to toner build-up. Once clean, the rollers in the unit should have a dullness to them and should be
somewhat “tacky.”
1. First make sure that the machine is powered of
pressing the release button located to the left of the control panel.
Once the unit is open locate the fold rollers inside the machine. To begin, simply spray the Formax Roller
2.
Cleaner on a cotton cloth until the rag is saturated.
several times over the roller. You will also need to rotate the roller as you clean it to reach all surfaces on
the roller. The amount of scrubbing will depend on the condition of the rollers. Once you are satisfied
with the cleaning, be sure to take a clean rag and remove the excess roller cleaner from the roller surface.
Fold
Rollers
f and unplugged from the power source. Open the unit by
Apply the cleaner by rubbing the cloth back and forth
Insertion
Rollers
Seal
Rollers
3. It is also important to run 20 to 30 cycles with blank copy paper or anything that is not the customer’s live
application.
sure you do not smudge the live application.
4. To clean the feed tires in the paper feeder, choose a job that is in the “AUTO A” mode so you will be
able to run out of all the feeders. Spray some roller cleaner on an envelope and place it into the feed tray
under the left and then right feed tire. It is important to HOLD ON to the envelope before you press the
“STAR
envelope. Repeat this procedure as needed on each feed tire.
5. Repeat this cleaning procedure for the Envelope Feeder and for the “C” Feeder also.
This is because there will still be some residue of cleaner on the rollers and you want to make
T” button. Once you press START the feed tires will spin themselves on the cleaner located on the
Loading...