Formax Cut-True 22S User Manual

Cut-True 22S

Electric Paper Cutter

	OPERATOR MANUAL
1/2013	FIRST EDITION

	INDEX
CONTENTS	PAGE

Safety Instructions

1

Getting to know your paper trimmer

6

Blade Replacement Instruction

8

Safety Instruction:

Safety Instruction:

1. Carefully read this instruction manual before operating the machine.

People who operate the machine must read and fully understand how to use the safety equipment, and have the ability to follow and implement the regulations stated in this instruction manual.

2.Keep guards/covers in place.

All components which may endanger the operator are covered by the guards or covers.

Please keep the guards/covers in place and do not remove them without dealer or manufacturer’s consent.

3. Don’t use it in a dangerous environment.

Do not use the machine in humid or damp locations, or directly expose it to rain or sunlight. The working area must be well lit and ventilated.

4. Store idle machine.

If you don’t want to use it for a period of time, please store it in a dry and secure environment.

5.Stand in the proper position for operation.

Please stand in front of the machine while operating it.

6. Don’t overuse the machine.

Please use it properly and follow the steps for each of the functions stated in the instruction manual.

7. Operate it while you are in good health.

For safety reasons, do not operate the machine when you are tired or unable to focus on the job.

8. Keep both hands away from the cutting area.

The machine is designed to be and only allows a one-man operation. Each single cutting action must be operated by pressing the 2 enable switches simultaneously to avoid injury.

9. Keep away from the sharp edge of the blade.

Please wear leather gloves and use the cutter blade holders to replace or install the blade.

10.Maintain machine with care.

Repairing the machine or sharpening the blade must be carried out by qualified and well-trained people only. If you don’t use the replacement parts from the original manufacturer, it may result in considerable danger to the operator.

11.Waste disposal shall obey the local regulations and must be done carefully.

12.The measurement of the noise level is defined according to ISO 3746.

A weighted sound pressure level measuring under no load at operation position is 75.6Db (A), and under load at operation position is 75.5dB (A).

13.Make sure that the machine is disconnected at the power supply.

Shut down the power before starting to do any maintenance, adjustments, or repairs.

14.Application and prohibition of using the machine.

The machine is designed for trimming paper only. For safety reasons, do not attempt to cut other materials such as metal sheets, wood board or other objects.

15.Do not use the machine over its capacity.

Refer to the specifications of the machine shown in the instruction manual. Any modifications to the machine are not allowed and will terminate the manufacturer’s guarantee.

16.If any transmission elements fail, do not forcefully drag the paper pile out.

17.To ensure the optimal effectiveness of the machine, the safety devices need to be checked before operation. The test results ( see annex A) must be recorded after the blade has been changed or adjusted.

01

Installation of the machine:

The back-gauge crank, clamp hand wheel with screws and some related tools are separately and properly packed in a box with the machine. Please install these items right away.

The top part of the machine and the stand must be connected as follows:

1.Assemble the stand in the way that the 4 foundations match the colors marked on the stand, and secure each connected part with hexagonal screws.

2.Correctly place and install the machine on the stand with care , and tighten the 4 hexagonal nuts to secure the stand and machine.

Operation Description

1.Push the back-gauge crank slightly toward the machine and turn it counterclockwise in order to load the paper pile on the deck.

Note : To prevent the back gauge device moving forward and backward while cutting, pull the back-gauge crank toward to the operator to make it idle.

2.Turn the clamp hand wheel clockwise to clamp the paper pile and close the safety guard.

3.Push the 2 enable switches simultaneously and hold them until the cutting cycle is complete.

4.The optical cutting line will project the right cutting position on the paper pile.

Specification:

	Des.	\ Model		22S	3952S	3951	3951S
	Power Supply		-	1~, 120V, 60Hz	1~,230V,50Hz	1~,120V,60Hz	1~,120V,60Hz
	Cutting Capacity_		m	45PP	45 (450 sheets)	45 (450 sheets)	45 (450 sheets)
	(80gsm paper)
	Max.Cutting Width		430 PP		430	430	430
	Max.Cutting Length		mm	430	430	430	430
	Min.Cutting Lenth		mm	51	51	51	51
	Main Motor Power		mm	0.4 (1/2HP)	0.4 (1/2HP)	0.4 (1/2HP)	0.4 (1/2HP)
	Dimensions(LxWxH)		mm	700x625x1200	700x625x1200	700x625x1200	700x625x1200
	Weight		K	92	92	90	92

02