FOREST MULTI REMOTE - 5201001460
TECHNICAL SPECIFIC ATION:
● 3V battery CR2430 ● transmit range indoors max. 30mtr
● battery life > 3 years ● working temperature -10°C - +50°C
● frequency 433.92MHz ● modes: manual, timer and dynamic timer (15 minutes + and -)
● transmit power 10mW ● each channel can control up to 20 receivers / motors
selected channel
manual/auto/dynamic mode mode button
open/up button
stop button time button
close/down button non applicable
channel +/-
battery slide (CR2430)
SET TIME:
PRESS MODE TO SET PRESS TIME FOR ~7SEC. PRESS BUTTONS TO PRESS TIME TO PRESS TIME ~7SEC. PRESS TIME ONCE
MODE TO MANUAL → 2 DIGITS WILL BLINK CHANGE TIME TOGGLE BETWEEN UNTIL ALL DIGITS MORE TO FINISH
‘man’ ON DISPLAY HOURS/MINUTES STOP BLINKING AND START CLOCK
BEFORE SETTING THE TIMER, SET THE CLOCK!
SET TIMER (EACH CHANNEL SEPARATE):
PRESS MODE TO SELECT CHANNEL PRESS TIME FOR PRESS BUTTONS TO PRESS TIME TO PRESS MODE TO SWITCH
SET MODE TO ~7SEC. → HOUR CHANGE OPEN▲ TIME TOGGLE BETWEEN TO CLOSE▼TIME
AUTO OR DYNAMIC DIGITS WILL BLINK HOURS/MINUTES
PRESS BUTTONS TO PRESS TIME TO PRESS TIME FOR ~7SEC. SET MODE TO
CHANGE CLOSE▼ TIME TOGGLE BETWEEN UNTIL DIGITS STOP AUTO OR DYNAMIC
HOURS/MINUTES BLINKING → FINISHED
11/2013 WDOC MULTI REMOTE
866-823-3894 / www.forestdh.com
1/4
FOREST MULTI REMOTE - 5201001460
MODE EXPLANATION:
Mode manual (man): remote can only be used manually. Timer function is switched off.
Mode automatic (auto): timer is switched on, only for the selected channel. Select channel 00 (all channels) to engage on all timers.
Mode dynamic ( ): same as automatic mode, open and close time will vary + and – 15 minutes.
FEATURES:
● When channel select is set to channel 00, all the channels 1 to 15 will respond to open and close.
● Default timer setting for every channel is: open 06:30AM, close 5:30PM.
● Dynamic mode: timer will vary open and close time between + and – 15 minutes. The first day dynamic mode is used the time will not
vary.
FREQUENT ASKED QUESTIONS:
● Q: Clock doesn’t start running after setting the time.
A: Press time button on the back once more.
● Q: I can’t succeed setting the time or the timer.
A: The interval between pressing different button must be within 10 seconds.
● Q: When I set a timer, the display shows Er:01
A: Time between open-time and close-time must be more than 30 minutes apart.
● Q: Timer only works on one channel.
A: Only the selected channel will work as a timer. Use channel 00 to turn on all timers (all channels).
● Q: I can’t succeed programming a remote / wall switch RF to a receiver
A: During programming, keep the remote / wallswitch RF clos e to the receiver (max 0,5 mtr)
BATTERY EMPTY:
After changing the battery, only the time must be set. Programmed receivers will stay in memory of remote. Please follow the local
regulations for disposal of the empty battery.
FOREST MULTI WALL SWITCH RF - 5201001470
TECHNICAL SPECIFIC ATION:
● 3V battery CR2032 ● transmit range indoor max. 30mtr
● battery life > 3 years ● working temperature -10°C - +50°C
● frequency 433.92MHz ● each channel can control up to 20 receivers
● transmit power 10mW
open/up button
stop button
close/down button
channel A channel B battery CR2032
BATTERY EMPTY:
After changing the battery, programmed receivers and timers will stay in memory of remote. Please follow the local regulations for disposal
of the empty battery.
11/2013 WDOC MULTI WALL REMOTE / SWITCH RF 866-823-3894 / www.forestdh.com
2/4
FOREST MULTI RECEIVER / WALL SWITCH – 5201001360 / 1 / 2
TECHNICAL SPECIFIC ATION:
● powered by Shuttle ● connect to port 1 of the Forest Shuttle
● can also be used as wall switch ● can control several Shuttles parallel
● cable 0,5mtr → 5201001360 ● working temperature -10°C - +50°C
● cable 3,5mtr → 5201001361 ● works on Forest Multi Remote and
● click-on → 5201001362 Forest Multi W all Switch RF
program button
program button control led
open/up button
stop button
close/down button
PROGRAMMING REMOTE / WALL CANCEL ONE CHANNEL OF DELETE ALL PREVIOUS
SWITCH TO RECEIVER: REMOTE / WALL SWITCH PROGRAMMED REMOTES /
WALL SWITCHES:
press program button, led will blink press program button, led will blink press stop and close button of
receiver for ~6 sec.
or or
press stop button press stop button led will blink and will go off
press program press program
button, led will button, led will
light up light up
hold the remote/wallswitch within
0,5 mtr from receiver. Select channel or
(1-15) and press open button: select channel and press close button:
led must blink 3 times and will go off led will blink and will go off
press and hold the program button
for 10 seconds until led starts blinking
11/2013 WDOC SHUTTLE MULTI RECEIVER
866-823-3894 / www.forestdh.com
3/4
FOREST FMS/BCS MULTI RECEIVER - 5104011500
TECHNICAL SPECIFIC ATION:
● power 230Vac – 500W ● terminal max 2,5mm²
● controls one motor ● one channel
● can also be used as wall switch ● working temperature -10°C - +50°C
● works on to Forest Multi Remote and ● programming identic al to Shuttle Multi Receiver
Forest Multi W all Switch RF
program button control led
open/up button
stop button
close/down button
WIRING DIAGRAM:
11/2013 WDOC FMS BCS MULTI RECEIVER
866-823-3894 / www.forestdh.com
4/4
Loading...