Wall Plate VGA CAT5 Extender
ITEM NO.: VW02
The VGA Extender allows VGA video signals to be transmitted up to 13 5 meters via 4-paris CAT5 STP
or UTP cable. Used in pairs, the VGA Extender is used in home or commercial applications as a smart,
fast and cost-effective, eliminates costly and bulky VGA cable, allowing VGA monitors to be co nnected
extended distances from the PC via standard twisted pair cable. Ideal for classrooms video
distr ibution, lecture halls, retail kiosks, video information displays, overhead projector systems,
PC-training systems, and tradeshows PC demo systems. Wall mountable type could be using CAT5
structuring cable for easy instal lation to simpl ifies and beautifies any audiovisual en vironment.
VW02 Wall Plate VGA CAT5 Extender
Used in pairs via one CAT5 UTP cable to send VGA up to 100 meters.
VGA connector to shielding RJ45 female.
Wall plate outer dimension: 86 x 86 mm
Passive device, no power required, not support VGA DDC protocol.
Supports up to 1280x1024 pixels.
Up to 135 meters via standard 4 pairs CAT5 STP or UTP cable instead of VGA cable.
T ransmitter built in virtual DDC to avoid improperly setting at resolution and frequency.
Transmitter built in sync mode selection for signal stability.
Receiver built in sync filter level adjustment for signal stability.
Perfect for classrooms, lecture halls, tradeshows, video information displays…etc.
Panel View:
VW02T VW02R
Installation View:
VW02T
VW02R
100M (Max)
FORESIGHT CCTV INC. | 5863 Leslie Street, Unit#713, North York, Ontario,Canada, M2H 1J8 | http://www.foresight-cctv.com | 1-888-GO2-CCTV
Installation:
Recommend Cable:
1. CAT5e UTP/ STP or CAT6 UTP cable.
2. There are some certain models or brands of monitors with very high demand at sync-sensitive,
recommend use STP (shielding twisted pair) cable to instead of UTP (unshielded twisted pair) cable.
RJ45 Pin Configuration: TIA/EIA 568B Wiring standard
1. Orange-white Red +
2. Orange Red -
3. Green-white H-Sync
4. Blue Green +
5. Blue-white Green -
6. Green V-Sync
7. Brown-white Blue +
8. Brown Blue -
Slide Switch Setting:
VW02-T Sync Mode Select
← Mode 1
→ Mode 2
1. For new type monitors, such like over 17” L CD Mo nito r, recommends setting at mode 1
for the best stability. If the picture not normal, then switch to Mode 2.
2. For old type monito rs, such like CRT or under 17” LCD Monitor, recommend setting at
mode 2. If the picture still not normal after adjust the dip switch of VE01P-R. Then
please use STP (shielding twisted pair) cable.
DIP Switch Setting:
VW02-R Sync Filter Level
====================
１２３４５
↓↓↓↓↓ Level 0 (Min)
↑↓↓↓↓ Level 1
↓↑↓↓↓ Level 2
↓↓↑↓↓ Level 3
↓↓↓↑↓ Level 4
↓↓↓↓↑ Level 5 (Max)
Sync Filter is designed for using UTP CAT5 cabling.
Sync Filter level adjustment is to add the sync stability, but not adjust picture quality or
eliminate skew.
Since different brand monitor have different setting, so there is no recommended setting.
Please adjust the level based on picture stability. I f no picture display or picture not stable, then
please use STP cable.
Caution:
1. The wiring must be away from electro magnetic equipment, i.e. microwave, wireless, hi voltage
cable…etc.
2. The maximum distances supported by the VGA Extender are dependent on the type of twisted pair
cable and image resolution of the PC’s VGA interface. Make sure that the maximum
recommended operational distances have not been exceeded.
3. All wiring is “straight-through” twisted pair cable, not being used for other LAN or telephone
FORESIGHT CCTV INC. | 5863 Leslie Street, Unit#713, North York, Ontario,Canada, M2H 1J8 | http://www.foresight-cctv.com | 1-888-GO2-CCTV
equipment.
4. Do not connect the VGA Extender to a telecommunication outlet wired to unrelated equipment.
Troubleshooting at picture problem:
1. No picture display:
Check Link cable.
Check DIP switch setting.
Check VGA cable connect.
Change the resolution or frequency.
Change Link cable for STP cable.
2. Picture not stable or disappear intermittence or no picture display:
Check DIP switch setting.
Change the resolution or frequency.
Wiring away from electro magnet ic equipments.
Change Link cable for STP cable.
3. Picture tilt:
Check DIP switch setting.
Change the resolution or frequency.
Change Link cable for STP cable.
Application Tips to use CAT5 STP cable:
Following is the correct cable connection when use STP cable:
1. S TP (shielding twisted pair) Cable.
2. STP (shielding) RJ45 connector with STP cable connection.
Specification:
ITEM NO. VW02T VW02R
Input Signals
Video: 1 Vp-p
Horizontal & Ver tical SYNC : TTL standard. 300kHz max. bandwidt h
Insertion Loss
Less than 3dB per pair over the frequency range
Video Signal Return Loss
-15dB max from DC to 60Mhz
75 ohms (DB15), 100 ohms (RJ45)
Setting Switch
2 Stage Slide Switch
5 Stage Dip Switch
Transmission Distance
60 -100 meters depend on image resolution
Link Cable
CAT5 / CAT5e / CAT6 / STP or UTP Cable
Temperature
Operation: 0 to 55 C, Storage: -20 TO 85 c, Humidity: up to 95%
Dimensions mm
86 x 55 x 86
86 x 55 x 86
Weight g
122
120
Rev. B
Max. Distance via CAT5 Cable
800x600 pixels (30MHz) 100M
1024x768 pixels (60MHz) 75M
1280x1024 pixels (100MHz) 60M
FORESIGHT CCTV INC. | 5863 Leslie Street, Unit#713, North York, Ontario,Canada, M2H 1J8 | http://www.foresight-cctv.com | 1-888-GO2-CCTV
Loading...