FORD Fusion 2013 User Manual v.2

fordowner.com ford.ca

2013 FUSION Owner’s Manual

The information contained in this publication was correct at the time of going to print. In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission. Errors and omissions excepted.

Part Number: 20121026184531

Introduction

About This Manual...........................................7

Symbols Glossary.............................................7

Data Recording..................................................9

California Proposition 65..............................11

Perchlorate.........................................................11

Ford Credit..........................................................11

Replacement Parts

Recommendation........................................11

Special Notices................................................12

Mobile Communications

Equipment.....................................................12

Export Unique Options..................................12

Child Safety

General Information.......................................13

Child Seat Positioning...................................15

Booster Seats...................................................16

Installing Child Seats.....................................18

Child Safety Locks..........................................23

Safety Belts

Principle of Operation...................................25

Fastening the Safety Belts..........................26

Safety Belt Height Adjustment.................28

Safety Belt Warning Lamp and Indicator

Chime.............................................................29

Safety Belt Minder.........................................29

Child Restraint and Safety Belt

Maintenance.................................................31

Personal Safety System™

Personal Safety System™..........................32

Supplementary Restraints

System

Principle of Operation...................................33

Driver and Passenger Airbags...................34

Knee Airbag......................................................35

Front Passenger Sensing System............35

Side Airbags.....................................................38

Side Curtain Airbags.....................................39

Crash Sensors and Airbag Indicator.......40

Airbag Disposal................................................41

Keys and Remote Controls

General Information on Radio

Frequencies..................................................42

Remote Control..............................................42

Replacing a Lost Key or Remote

Control............................................................47

MyKey™

Principle of Operation..................................48

Creating a MyKey...........................................48

Clearing All MyKeys.......................................49

Checking MyKey System Status..............49

Using MyKey With Remote Start

Systems.........................................................49

MyKey Troubleshooting...............................50

Locks

Locking and Unlocking..................................51

Keyless Entry....................................................54

Interior Luggage Compartment

Release...........................................................57

Security

Passive Anti-Theft System........................58

Anti-Theft Alarm...........................................60

Steering Wheel

Adjusting the Steering Wheel....................61

Audio Control....................................................61

Voice Control...................................................62

Cruise Control..................................................62

Information Display Control.......................62

Wipers and Washers

Windshield Wipers........................................64

Table of Contents

Autowipers.......................................................64

Windshield Washers.....................................65

Lighting

Lighting Control..............................................66

Autolamps........................................................66

Instrument Lighting Dimmer......................67

Headlamp Exit Delay....................................67

Daytime Running Lamps.............................67

Automatic High Beam Control.................68

Front Fog Lamps............................................69

Direction Indicators.......................................69

Interior Lamps.................................................69

Windows and Mirrors

Power Windows...............................................71

Global Opening and Closing.......................72

Exterior Mirrors.................................................72

Interior Mirror....................................................73

Sun Visors..........................................................74

Moonroof...........................................................74

Instrument Cluster

Gauges................................................................76

Warning Lamps and Indicators.................78

Audible Warnings and Indicators..............81

Information Displays

General Information......................................82

Information Messages.................................90

Audio System

General Information....................................105

Audio unit - Vehicles With:

AM/FM/CD/SYNC/Satellite

Radio............................................................106

Audio unit - Vehicles With: Premium

AM/FM/CD.................................................108

Audio unit - Vehicles With: Sony

AM/FM/CD..................................................110

Auxiliary Input Jack.......................................113

USB Port...........................................................114

Media Hub........................................................114

Digital Audio Broadcasting........................115

Satellite Radio................................................115

Climate Control

Manual Climate Control.............................118

Automatic Climate Control.......................119

Automatic Climate Control........................121

Automatic Climate Control.......................123

Hints on Controlling the Interior

Climate.........................................................124

Heated Windows and Mirrors..................126

Cabin Air Filter................................................127

Remote Start..................................................127

Seats

Sitting in the Correct Position..................129

Head Restraints.............................................129

Manual Seats..................................................131

Power Seats.....................................................131

Memory Function..........................................132

Rear Seats.......................................................134

Heated Seats..................................................134

Rear Seat Armrest........................................135

Universal Garage Door

Opener

Universal Garage Door Opener...............136

Auxiliary Power Points

Auxiliary Power Points...............................140

Storage Compartments

Center Console..............................................142

Overhead Console........................................142

Table of Contents

Starting and Stopping the

Engine

General Information....................................143

Ignition Switch...............................................143

Keyless Starting............................................143

Starting a Gasoline Engine.......................144

Engine Block Heater.....................................147

Unique Driving Character-

istics

Start-Stop.......................................................149

Fuel and Refueling

Safety Precautions........................................151

Fuel Quality.....................................................152

Refueling..........................................................152

Running Out of Fuel.....................................153

Fuel Consumption........................................155

Emission Control System..........................155

Transmission

Manual Transmission.................................158

Automatic Transmission...........................159

Hill Start Assist..............................................162

All-Wheel Drive

Using All-Wheel Drive................................164

Brakes

General Information....................................169

Hints on Driving With Anti-Lock

Brakes...........................................................169

Electric Parking Brake.................................170

Traction Control

Principle of Operation.................................173

Using Traction Control................................173

Stability Control

Principle of Operation.................................174

Using Stability Control................................175

Parking Aids

Parking Aid......................................................176

Active Park Assist.........................................178

Rear View Camera........................................181

Cruise Control

Principle of Operation.................................185

Using Cruise Control....................................185

Using Adaptive Cruise Control................186

Driving Aids

Driver Alert......................................................192

Lane Keeping System.................................195

Blind Spot Monitor......................................198

Steering...........................................................203

Load Carrying

Load Limit......................................................204

Towing

Towing a Trailer...............................................211

Recommended Towing Weights..............211

Essential Towing Checks...........................213

Transporting the Vehicle............................215

Towing the Vehicle on Four Wheels......215

Driving Hints

Breaking-In......................................................217

Economical Driving.......................................217

Driving Through Water................................217

Floor Mats........................................................218

Customer Assistance

Getting the Services You Need...............220

In California (U.S. Only)..............................221

The Better Business Bureau (BBB) Auto

Line Program (U.S. Only)......................222

Table of Contents

Utilizing the Mediation/Arbitration

Program (Canada Only)........................222

Getting Assistance Outside the U.S. and

Canada........................................................223

Ordering Additional Owner's

Literature....................................................224

Reporting Safety Defects (U.S.

Only).............................................................224

Reporting Safety Defects (Canada

Only).............................................................225

Roadside Emergencies

Roadside Assistance..................................226

Hazard Warning Flashers..........................227

Fuel Shutoff....................................................227

Jump-Starting the Vehicle........................227

Fuses

Changing a Fuse..........................................230

Fuse Specification Chart..........................230

Maintenance

General Information...................................240

Opening and Closing the Hood.............240

Under Hood Overview - 1.6L

EcoBoost™.................................................241

Under Hood Overview - 2.0L

EcoBoost™................................................242

Under Hood Overview - 2.5L...................243

Engine Oil Dipstick - 1.6L

EcoBoost™................................................244

Engine Oil Dipstick......................................244

Engine Oil Check..........................................244

Engine Coolant Check...............................245

Automatic Transmission Fluid

Check...........................................................248

Brake Fluid Check........................................248

Power Steering Fluid Check....................248

Fuel Filter........................................................249

Washer Fluid Check....................................249

Changing the 12V Battery.........................249

Checking the Wiper Blades.....................250

Changing the Wiper Blades.....................250

Changing the Engine Air Filter..................251

Adjusting the Headlamps.........................252

Removing a Headlamp..............................253

Changing a Bulb...........................................254

Bulb Specification Chart...........................257

Vehicle Care

General Information...................................259

Cleaning Products.......................................259

Cleaning the Exterior..................................259

Repairing Minor Paint Damage..............260

Waxing............................................................260

Cleaning the Engine.....................................261

Cleaning the Windows and Wiper

Blades...........................................................261

Cleaning the Interior....................................261

Cleaning the Instrument Panel and

Instrument Cluster Lens.......................262

Cleaning Leather Seats.............................263

Cleaning the Alloy Wheels.......................263

Vehicle Storage............................................264

Wheels and Tires

Tire Care..........................................................266

Using Snow Chains....................................280

Changing a Road Wheel............................281

Tire Pressure Monitoring System..........284

Technical Specifications..........................288

Capacities and Specific-

ations

Engine Specifications................................290

Motorcraft Parts............................................291

Vehicle Identification Number................293

Vehicle Certification Label.......................293

Transmission Code Designation............294

Technical Specifications...........................295

Table of Contents

Accessories

Accessories....................................................298

Ford Extended Service Plan

(ESP)

Ford Extended Service Plan (ESP)......300

SYNC™

General Information...................................303

Using Voice Recognition...........................305

Using SYNC™ With Your Phone............307

SYNC™ Applications and Services......320

Using SYNC™ With Your Media

Player............................................................327

SYNC™ Troubleshooting.........................335

MyFord Touch™

General Information....................................341

Settings...........................................................353

Entertainment..............................................362

Phone................................................................381

Information....................................................387

Climate............................................................396

Navigation.....................................................400

Appendices

End User License Agreement.................409

Scheduled Maintenance

Scheduled Maintenance...........................424

Table of Contents

ABOUT THIS MANUAL

Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it.

WARNING

Always drive with due care and attention when using and operating the controls and features on your

vehicle.

Note: This manual describes product features and options available throughout the range, sometimes even before they are generally available. It may describe options not fitted to your vehicle.

Note: Some of the illustrations in this manual may be used for different models, so may appear different to your vehicle. However, the essential information in the illustrations is always correct.

Note: Always use and operate your vehicle in line with all applicable laws and regulations.

Note: Pass on this manual when selling your vehicle. It is an integral part of the vehicle.

This manual may qualify the location of a component as left-hand side or right-hand side. The side is determined when facing forward in the seat.

E154903

Right-hand sideA Left-hand sideB

Protecting the Environment

You must play your part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps toward this aim.

SYMBOLS GLOSSARY

These are some of the symbols you may see on your vehicle.

Safety alert

See Owner's Manual

Anti-lock braking system

Avoid smoking, flames or sparks

Battery

Introduction

Battery acid

Brake fluid - non petroleum based

Brake system

Cabin air filter

Check fuel cap

Child safety door lock or unlock

Child seat lower anchor

Child seat tether anchor

E71340

Cruise control

Do not open when hot

Engine air filter

Engine coolant

Engine coolant temperature

Engine oil

Explosive gas

Fan warning

Fasten safety belt

Front airbag

Front fog lamps

Fuel pump reset

Fuse compartment

Hazard warning flashers

Heated rear window

E91392

Heated windshield

Interior luggage compartment release

Jack

Lighting control

Low tire pressure warning

Maintain correct fluid level

Introduction

Panic alarm

E139213

Parking aid

Parking brake

Power steering fluid

Power windows front/rear

Power window lockout

Service engine soon

Side airbag

Stability control

Windshield wash and wipe

DATA RECORDING

Service Data Recording

Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly diagnose and service your vehicle, Ford Motor Company, Ford of Canada, and service and repair

facilities may access or share among them vehicle diagnostic information received through a direct connection to your vehicle when diagnosing or servicing your vehicle. Additionally, when your vehicle is in for service or repair, Ford Motor Company, Ford of Canada, and service and repair facilities may access or share among them data for vehicle improvement purposes. For U.S. only (if equipped), if you choose to use the SYNC Vehicle Health Report, you consent that certain diagnostic information may also be accessed electronically by Ford Motor Company and Ford authorized service facilities, and that the diagnostic information may be used for any purpose. See SYNC™ (page 303).

Event Data Recording

This vehicle is equipped with an event data recorder. The main purpose of an event data recorder is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle; this data will assist in understanding how a vehicle’s systems performed. The event data recorder is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.

The event data recorder in this vehicle is designed to record such data as:

• How various systems in your vehicle were operating;

• Whether or not the driver and passenger safety belts were buckled/fastened;

• How far (if at all) the driver was depressing the accelerator and/or the brake pedal; and

• How fast the vehicle was travelling; and

• Where the driver was positioning the steering wheel.

Introduction

This data can help provide a better understanding of the circumstances in which crashes and injuries occur.

Note: Event data recorder data is

recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the event data recorder under normal driving conditions and no personal data or information (e.g., name, gender, age, and crash location) is recorded (see limitations regarding 911 Assist and Traffic, directions and Information privacy below). However, parties, such as law enforcement, could combine the event data recorder data with the type of personally identifying data routinely acquired during a crash investigation.

To read data recorded by an event data recorder, special equipment is required, and access to the vehicle or the event data recorder is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have such special equipment, can read the information if they have access to the vehicle or the event data recorder. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, unless pursuant to court order or where required by law enforcement, other government authorities or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada.

Note: Including to the extent that any

law pertaining to Event Data Recorders applies to SYNC or its features, please note the following: Once 911 Assist (if equipped) is enabled (set ON), 911 Assist may, through any paired and connected cell phone, disclose to emergency services that the vehicle has been in a crash involving the deployment of an airbag or, in certain vehicles, the activation of the fuel pump shut-off. Certain versions or updates to 911 Assist may also be capable of being used to electronically or verbally provide to 911 operators the vehicle location (such as latitude and longitude), and/or other details about the vehicle or crash or personal information about the occupants to assist 911 operators to provide the most appropriate emergency services. If you do not want to disclose this information, do not activate the 911 Assist feature. See SYNC™ (page 303).

Additionally, when you connect to Traffic, Directions and Information (if equipped, U.S. only), the service uses GPS technology and advanced vehicle sensors to collect the vehicle’s current location, travel direction, and speed (“vehicle travel information”), only to help provide you with the directions, traffic reports, or business searches that you request. If you do not want Ford or its vendors to receive this information, do not activate the service. Ford Motor Company and the vendors it uses to provide you with this information do not store your vehicle travel information. For more information, see Traffic, Directions and Information, Terms and Conditions.

See SYNC™ (page 303).

Introduction

CALIFORNIA PROPOSITION 65

WARNING

Some constituents of engine exhaust, certain vehicle components,

certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

PERCHLORATE

Certain components in your vehicle such as airbag modules, safety belt pretensioners and remote control batteries may contain perchlorate material. Special handling may apply for service or vehicle end of life disposal. For more information vist:

Web Address

www.dtsc.ca.gov/hazardouswaste/

perchlorate

FORD CREDIT

(U.S. Only)

Ford Credit offers a full range of financing and lease plans to help you acquire your vehicle. If you have financed or leased your vehicle through Ford Credit, thank you for your business.

For your convenience we offer a number of ways to contact us, as well as help manage your account.

Phone: 1-800-727-7000 For more information regarding Ford Credit,

as well as access Account Manager, please go to www.fordcredit.com.

REPLACEMENT PARTS RECOMMENDATION

Your vehicle has been built to the highest standards using quality parts. We recommend that you demand the use of genuine Ford and Motorcraft parts whenever your vehicle requires scheduled maintenance or repair. You can clearly identify genuine Ford and Motorcraft parts by looking for the Ford, FoMoCo or Motorcraft branding on the parts or their packaging.

Scheduled Maintenance and Mechanical Repairs

One of the best ways for you to make sure that your vehicle provides years of service is to have it maintained in line with our recommendations using parts that conform to the specifications detailed in this Owner’s Manual. Genuine Ford and Motorcraft parts meet or exceed these specifications.

Collision Repairs

We hope that you never experience a collision, but accidents do happen. Genuine Ford replacement collision parts meet our stringent requirements for fit, finish, structural integrity, corrosion protection and dent resistance. During vehicle development we validate these parts deliver the intended level of protection as a whole system. A great way to know for sure you are getting this level of protection is to use genuine Ford replacement collision parts.

Introduction

Warranty on Replacement Parts

Genuine Ford and Motorcraft replacement parts are the only replacement parts that benefit from a Ford Warranty. Damage caused to your vehicle as a result of the failure of non-Ford parts may not be covered by the Ford Warranty. For additional information, refer to the terms and conditions of the Ford Warranty.

SPECIAL NOTICES

New Vehicle Limited Warranty

For a detailed description of what is covered and what is not covered by your vehicle’s New Vehicle Limited Warranty, refer to the Warranty Manual that is provided to you along with your Owner’s Manual.

Special Instructions

For your added safety, your vehicle is fitted with sophisticated electronic controls.

WARNINGS

Failure to follow the specific warnings and instructions could result in personal injury. See

Supplementary Restraints System

(page 33).

Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active

passenger airbag.

MOBILE COMMUNICATIONS EQUIPMENT

Using mobile communications equipment is becoming increasingly important in the conduct of business and personal affairs. However, you must not compromise your own or others’ safety when using such equipment. Mobile communications can

enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits. Mobile communication equipment includes, but is not limited to, cellular phones, pagers, portable email devices, text messaging devices and portable two-way radios.

WARNING

Driving while distracted can result in loss of vehicle control, accident and

injury. We strongly recommend that you use extreme caution when using any device or feature that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any handheld device while driving and that you comply with all applicable laws.

EXPORT UNIQUE OPTIONS

For your particular global region, your vehicle may be equipped with features and options that are different from the features and options that are described in this Owner’s Manual. A market unique supplement may be supplied that complements this book. By referring to the market unique supplement, if provided, you can properly identify those features, recommendations and specifications that are unique to your vehicle. This Owner’s Manual is written primarily for the U.S. and Canadian Markets. Features or equipment listed as standard may be different on units built for Export. Refer to this Owner’s

Manual for all other required information and warnings.

Introduction

GENERAL INFORMATION

See the following sections for directions on how to properly use safety restraints for children.

WARNINGS

Always make sure your child is secured properly in a device that is

appropriate for their height, age and weight. Child safety restraints must be bought separately from your vehicle. Failure to follow these instructions and guidelines may result in an increased risk of serious injury or death to your child.

All children are shaped differently.

The recommendations for safety

restraints are based on probable child height, age and weight thresholds from National Highway Traffic Safety Administration and other safety organizations, or are the minimum

WARNINGS

requirements of law. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician and consult your pediatrician to make sure your child seat is appropriate for your child, and is compatible with and properly installed in your vehicle. To locate a child seat fitting station and CPST, contact the NHTSA toll free at 1-888-327-4236 or locate NHTSA on the internet. In Canada, check with your local St. John Ambulance office for referral to a CPST or for further information, contact your provincial ministry of transportation, locate your local St. John Ambulance office by searching for St. John Ambulance on the internet, or Transport Canada at 1-800-333-0371 (http://www.tc.gc.ca). Failure to properly restrain children in safety seats made especially for their height, age, and weight may result in an increased risk of serious injury or death to your child.

Child Safety

Recommendations for Safety Restraints for Children

Recommended restraint

type

Child size, height, weight, or ageChild

Use a child safety seat

(sometimes called an

infant carrier, convertible

seat, or toddler seat).

Children weighing 40 lb (18 kg) or less

(generally age four or younger).

Infants or

toddlers

Use a belt-positioning

booster seat.

Children who have outgrown or no longer

properly fit in a child safety seat (gener-

ally children who are less than 4 ft. 9 in.

(1.45 m) tall, are greater than age four (4)

and less than age twelve (12), and

between 40 lb (18 kg) and 80 lb (36 kg)

and upward to 100 lb (45 kg) if recom-

mended by your child restraint manufac-

turer).

Small children

Use a vehicle safety belt having the lap belt snug and low across the hips,

shoulder belt centered

across the shoulder and

chest, and seat back

upright.

Children who have outgrown or no longer

properly fit in a belt-positioning booster seat (generally children who are at least 4 ft. 9 in. (1.45 m) tall or greater than 80

lb (36 kg) or 100 lb (45 kg) if recom-

mended by child restraint manufacturer).

Larger children

Child Safety

• You are required by law to properly use safety seats for infants and toddlers in the United States and Canada.

• Many states and provinces require that small children use approved booster seats until they reach age eight, a height of 4 feet 9 inches (1.45 meters) tall, or 80 pounds (36 kilograms). Check your local and state or provincial laws for specific requirements about the safety of children in your vehicle.

• When possible, always properly restrain children twelve years of age and under in a rear seating position of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in a front seating position. See Front Passenger

Sensing System (page 35).

CHILD SEAT POSITIONING

WARNINGS

Airbags can kill or injure a child in a child seat. Never place a rear-facing

child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the vehicle seat upon which the child seat is installed all the way back. When possible, all children age 12 and under should be properly restrained in a rear seating position. If all children cannot be seated and restrained properly in a rear seating position, properly restrain the largest child in the front seat.

WARNINGS

Always carefully follow the instructions and warnings provided

by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child's size, height, weight, or age. Follow the child restraint manufacturer's instructions and warnings provided for installation and use in conjunction with the instructions and warnings provided by your vehicle manufacturer. A safety seat that is improperly installed or utilized, is inappropriate for your child's height, age, or weight or does not properly fit the child may increase the risk of serious injury or death.

Never let a passenger hold a child on

his or her lap while your vehicle is

moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury or death.

Never use pillows, books, or towels

to boost a child. They can slide

around and increase the likelihood of injury or death in a collision.

Always restrain an unoccupied child

seat or booster seat. These objects

may become projectiles in a collision or sudden stop, which may increase the risk of serious injury.

Never place, or allow a child to place,

the shoulder belt under a child's arm

or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision.

To avoid risk of injury, do not leave

children or pets unattended in your

vehicle.

Child Safety

Use any attachment method as indicated below by XChild

Weight

Restraint

Type

Safety belt

only

Safety belt and LATCH

(lower

anchors

and top

tether

anchor)

Safety belt

and top

tether

anchor

LATCH (lower

anchors

only)

LATCH

(lower anchors and top

tether

anchor)

XXUp to 48 lb

(21 kg)

Rear facing

child seat

XXXUp to 48 lb

(21 kg)

Forward

facing

child seat

XXOver 48 lb

(21 kg)

Forward

facing

child seat

Note: The child seat must rest tightly against the vehicle seat upon which it is installed. It may be necessary to lift or remove the head restraint. See Seats (page

129).

BOOSTER SEATS

WARNING

Never place, or allow a child to place, the shoulder belt under a child's arm

or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision.

Use a belt-positioning booster seat for children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 feet 9 inches (1.45 meters) tall, are greater than age four (4) and less than age twelve (12), and between 40 pounds (18 kilograms) and 80 pounds (36 kilograms) and upward to 100 pounds (45 kilograms) if

recommended by your child restraint manufacturer). Many state and provincial laws require that children use approved booster seats until they reach age eight, a height of 4 feet 9 inches (1.45 meters) tall, or 80 pounds (36 kilograms).

Booster seats should be used until you can answer YES to ALL of these questions when seated without a booster seat:

E142595

Child Safety

• Can the child sit all the way back against their vehicle seat back with knees bent comfortably at the edge of the seat cushion?

• Can the child sit without slouching?

• Does the lap belt rest low across the

hips?

• Is the shoulder belt centered on the shoulder and chest?

• Can the child stay seated like this for the whole trip?

Always use booster seats in conjunction with your vehicle lap and shoulder belt.

Types of Booster Seats

E68924

• Backless booster seats

If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child's head (as measured at the tops of the ears) above the top of the seat. In this case, move the backless booster to another seating position with a higher seat back or head restraint and lap and shoulder belts, or consider using a high back booster seat.

E70710

• High back booster seats If, with a backless booster seat, you cannot

find a seating position that adequately supports your child's head, a high back booster seat would be a better choice.

Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder. The following drawings compare the ideal fit (center) to a shoulder belt uncomfortably close to the neck and a shoulder belt that could slip off the shoulder. The drawings also show how the lap belt should be low and snug across the child's hips.

Child Safety

E142596

E142597

If the booster seat slides on the vehicle seat upon which it is being used, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition. Do not introduce any item thicker than this under the booster seat. Check with the booster seat manufacturer's instructions.

INSTALLING CHILD SEATS

Child Seats

E142594

Child Safety

Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat) for infants, toddlers, or children weighing 40 pounds (18 kilograms) or less (generally age four or younger).

Using Lap and Shoulder Belts

WARNINGS

Airbags can kill or injure a child in a child seat. Never place a rear-facing

child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.

Airbags can kill or injure a child in a

child seat. Children 12 and under

should be properly restrained in the rear seat whenever possible.

Depending on where you secure a

child restraint, and depending on the

child restraint design, you may block access to certain safety belt buckle assemblies and LATCH lower anchors, rendering those features potentially unusable. To avoid risk of injury, occupants should only use seating positions where they are able to be properly restrained.

When installing a child safety seat with combination lap and shoulder belts:

• Use the correct safety belt buckle for

that seating position.

• Insert the belt tongue into the proper

buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.

• Keep the buckle release button

pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling.

• Place the vehicle seat upon which the child seat will be installed in the upright position.

• Put the safety belt in the automatic locking mode. See Step 5. This vehicle does not require the use of a locking clip.

Perform the following steps when installing the child seat with combination lap and shoulder belts:

Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat.

E142528

1. Position the child safety seat in a seat with a combination lap and shoulder belt.

E142529

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together.

Child Safety

E142530

3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer's instructions. Be sure the belt webbing is not twisted.

E142531

4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it.

E142875

5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out.

Note: The automatic locking mode is available on the front passenger and rear seats. This vehicle does not require the use of a locking clip.

6. Allow the belt to retract to remove slack. The belt will click as it retracts to indicate it is in the automatic locking mode.

7. Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode (you should not be able to pull more belt out). If the retractor is not locked, unbuckle the belt and repeat Steps 5 and 6.

E142533

Child Safety

8. Remove remaining slack from the belt. Force the seat down with extra weight, for example, by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt. This is necessary to remove the remaining slack that will exist once the extra weight of the child is added to the child restraint. It also helps to achieve the proper snugness of the child seat to your vehicle. Sometimes, a slight lean toward the buckle will additionally help to remove remaining slack from the belt.

9. Attach the tether strap (if the child seat is equipped).

E142534

10. Before placing the child in the seat,

forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than 1 inch (2.5 centimeters) of movement for proper installation.

Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician to make certain the child restraint is properly installed. In Canada, check with your local St. John Ambulance office for referral to a Certified Passenger Seat Technician.

Using Lower Anchors and Tethers for CHildren (LATCH)

WARNINGS

Never attach two child safety seats to the same anchor. In a collision, one

anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death.

Depending on where you secure a

child restraint, and depending on the

child restraint design, you may block access to certain safety belt buckle assemblies or LATCH lower anchors, rendering those features potentially unusable. To avoid risk of injury, occupants should only use seating positions where they are able to be properly restrained.

The LATCH system is composed of three vehicle anchor points: two lower anchors located where seat back and seat cushion meet (called the seat bight) and one top tether anchor located behind that seating position.

LATCH compatible child safety seats have two rigid or webbing mounted attachments that connect to the two lower anchors at the LATCH equipped seating positions in your vehicle. This type of attachment method eliminates the need to use safety belts to attach the child seat, however the safety belt can still be used to attach the child seat. For forward-facing child seats, the top tether strap must also be attached to the proper top tether anchor, if a top tether strap has been provided with your child seat.

Child Safety

E142535

Your vehicle has LATCH lower anchors for child seat installation at the seating positions marked with the child seat symbol.

E144054

The LATCH anchors are located at the rear section of the rear seat between the cushion and seat back below the symbols as shown. Follow the child seat manufacturer's instructions to properly install a child seat with LATCH attachments. Follow the instructions on attaching child safety seats with tether straps.

Attach LATCH lower attachments of the child seat only to the anchors shown.

Use of Inboard Lower Anchors from the Outboard Seating Positions (Center Seating Use)

Note: The standardized spacing for LATCH

lower anchors is 11 inches (28 centimeters) center to center. Do not use LATCH lower anchors for the center seating position unless the child seat manufacturer's instructions permit and specify using anchors spaced at least as far apart as those in this vehicle.

The lower anchors at the center of the second row rear seat are spaced 18 inches (46 centimeters) apart. A child seat with rigid LATCH attachments cannot be installed at the center seating position. LATCH compatible child seats (with attachments on belt webbing) can only be used at this seating position provided that the child seat manufacturer's instructions permit use with the anchor spacing stated. Do not attach a child seat to any lower anchor if an adjacent child seat is attached to that anchor.

Each time you use the safety seat, check that the seat is properly attached to the lower anchors and tether anchor, if applicable. Tug the child seat from side to side and forward and back where it is secured to your vehicle. The seat should move less than one inch when you do this for a proper installation.

If the safety seat is not anchored properly, the risk of a child being injured in a crash greatly increases.

Combining Safety Belt and LATCH Lower Anchors for Attaching Child Safety Seats

When used in combination, either the safety belt or the LATCH lower anchors may be attached first, provided a proper installation is achieved. Attach the tether strap afterward, if included with the child seat.

Child Safety

Using Tether Straps

Many forward-facing child safety seats include a tether strap

which extends from the back of the child safety seat and hooks to an anchoring point called the top tether anchor. Tether straps are available as an accessory for many older safety seats.

Contact the manufacturer of your child seat for information about ordering a tether strap, or to obtain a longer tether strap if the tether strap on your safety seat does not reach the appropriate top tether anchor in your vehicle.

Once the child safety seat has been installed using either the safety belt, the lower anchors of the LATCH system, or both, you can attach the top tether strap.

The tether strap anchors in your vehicle are in the following positions (shown from top view):

E142537

Perform the following steps to install a child safety seat with tether anchors:

Note: If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off your vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat. Keeping the child seat just touching your vehicle seat gives the best protection in a severe crash.

1. Route the child safety seat tether strap over the back of the seat. For outboard seating positions, route the tether strap under the head restraint and between the head restraint posts. For the center seating positions, route the tether strap over the top of the head restraint. If needed, the head restraints can also be removed.

E144274

2. Locate the correct anchor for the selected seating position, then open the tether anchor cover.

E144275

3. Clip the tether strap to the anchor as shown.

4. Tighten the child safety seat tether strap according to the manufacturer's instructions. If your child restraint system is equipped with a tether strap, and the child restraint manufacturer recommends its use, Ford also recommends its use.

CHILD SAFETY LOCKS

When these locks are set, the rear doors cannot be opened from the inside.

Child Safety

E112197

The childproof locks are located on the rear edge of each rear door and must be set separately for each door.

Left-Hand Side

Turn counterclockwise to lock and clockwise to unlock.

Right-Hand Side

Turn clockwise to lock and counterclockwise to unlock.

Child Safety

PRINCIPLE OF OPERATION

WARNINGS

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

To reduce the risk of injury, make sure children sit where they can be properly restrained.

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot

protect the child from injury in a collision.

All occupants of the vehicle, including the driver, should always

properly wear their safety belts, even when an airbag supplemental restraint system is provided.

It is extremely dangerous to ride in a

cargo area, inside or outside of a

vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.

In a rollover crash, an unbelted

person is significantly more likely to

die than a person wearing a safety belt.

Each seating position in your vehicle

has a specific safety belt assembly

which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.

When possible, all children 12 years

old and under should be properly

restrained in a rear seating position.

WARNINGS

Safety belts and seats can become hot in a vehicle that has been closed

up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them.

Front and rear seat occupants,

including pregnant women, should

wear safety belts for optimum protection in an accident.

All seating positions in this vehicle have lap and shoulder safety belts. All occupants of the vehicle should always properly wear their safety belts, even when an airbag supplemental restraint system is provided.

The safety belt system consists of:

• Lap and shoulder safety belts.

• Shoulder safety belt with automatic

locking mode, (except driver safety belt).

• Height adjuster at the front outboard

seating positions.

• Safety belt pretensioner at the front

outboard seating positions.

• Belt tension sensor at the front

outboard passenger seating position.

• Safety belt warning light and chime.

• Crash sensors and monitoring system

with readiness indicator.

Safety Belts

The safety belt pretensioners at the front seating positions are designed to tighten the safety belts when activated. In frontal and near-frontal collisions, the safety belt pretensioners may be activated alone or, if the collision is of sufficient severity, together with the front airbags. The pretensioners may also activate when a side curtain airbag is deployed.

FASTENING THE SAFETY BELTS

The front outboard and rear safety restraints in the vehicle are combination lap and shoulder belts.

E142587

1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.

E142588

2. To unfasten, press the release button and remove the tongue from the buckle.

Restraint of Pregnant Women

WARNING

Always ride and drive with your seatback upright and the safety belt

properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips. The shoulder portion of the safety belt should be positioned across the chest. Pregnant women should also follow this practice. See the following figure.

E142590

Safety Belts

Pregnant women should always wear their safety belt. The lap belt portion of a combination lap and shoulder belt should be positioned low across the hips below the belly and worn as tight as comfort will allow. The shoulder belt should be positioned to cross the middle of the shoulder and the center of the chest.

Safety Belt Locking Modes

WARNINGS

After any vehicle collision, the safety belt system at all passenger seating

positions must be checked by an authorized dealer to verify that the automatic locking retractor feature for child seats is still functioning properly. In addition, all safety belts should be checked for proper function.

BELT AND RETRACTOR ASSEMBLY

MUST BE REPLACED if the safety

belt assembly automatic locking retractor feature or any other safety belt function is not operating properly when checked by an authorized dealer. Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.

All safety restraints in the vehicle are combination lap and shoulder belts. The driver safety belt has the first type of locking mode, and the front outboard passenger and rear seat safety belts have both types of locking modes described as follows:

Vehicle Sensitive Mode

This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 5 mph (8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.

In addition, the retractor is designed to lock if the webbing is pulled out too quickly. If this occurs, let the belt retract slightly and pull webbing out again in a slow and controlled manner.

Automatic Locking Mode

In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt.

When to Use the Automatic Locking Mode

This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions. Children 12 years old and under should be properly restrained in a rear seating position whenever possible. See Child Safety (page 13).

Safety Belts

How to Use the Automatic Locking Mode

E142591

1. Buckle the combination lap and shoulder belt.

2. Grasp the shoulder portion and pull downward until the entire belt is pulled out.

Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.

How to Disengage the Automatic Locking Mode

Disconnect the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.

Safety Belt Extension Assembly

WARNING

Do not use extensions to change the fit of the shoulder belt across the torso.

If the safety belt is too short when fully extended, a safety belt extension assembly can be obtained from an authorized dealer.

Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended.

SAFETY BELT HEIGHT ADJUSTMENT

WARNING

Position the safety belt height adjuster so that the belt rests across

the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a collision.

E145664

Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.

To adjust the shoulder belt height, pull the button and slide the height adjuster up or down. Release the button and pull down on the height adjuster to make sure it is locked in place.

Safety Belts

SAFETY BELT WARNING LAMP AND INDICATOR CHIME

This lamp illuminates and an audible warning will sound if the

driver's safety belt has not been fastened when the vehicle's ignition is turned on.

Conditions of operation

Then...If...

The safety belt warning light illuminates 1-

2 minutes and the warning chime sounds

4-8 seconds.

The driver's safety belt is not buckled

before the ignition switch is turned to the

on position...

The safety belt warning light and warning

chime turn off.

The driver's safety belt is buckled while the

indicator light is illuminated and the

warning chime is sounding...

The safety belt warning light and indicator

chime remain off.

The driver's safety belt is buckled before

the ignition switch is turned to the on posi-

tion...

SAFETY BELT MINDER

Belt-Minder®

This feature supplements the safety belt warning function by providing additional reminders by intermittently sounding a chime and illuminating the safety belt warning light when the driver's or front passenger's seat is occupied and the safety belt is unbuckled.

The system uses information from the front passenger sensing system to determine if a front seat passenger is present and therefore potentially in need of a warning. To avoid activating the Belt-Minder feature for objects placed in the front passenger seat, warnings will only be given to front seat occupants as determined by the front passenger sensing system.

If the Belt-Minder warnings have expired (warnings for about five minutes) for one occupant (driver or front passenger), the other occupant can still activate the Belt-Minder feature.

Safety Belts

Then...If...

The Belt-Minder feature will not activate.The driver's and front passenger's safety belts are buckled before the ignition switch is turned to the on position or less than 1-2

minutes have elapsed since the ignition

switch has been turned to on...

The Belt-Minder feature is activated - the

safety belt warning light illuminates and the warning chime sounds for six seconds every 25 seconds, repeating for about five

minutes or until the safety belts are

buckled.

The driver's or front passenger's safety belt is not buckled when the vehicle has reached at least 6 mph (9.7 km/h) and 1-2 minutes

have elapsed since the ignition switch has

been turned to on...

The Belt-Minder feature is activated - the

safety belt warning light illuminates and the warning chime sounds for six seconds every 25 seconds, repeating for about five

minutes or until the safety belts are

buckled.

The driver's or front passenger's safety belt becomes unbuckled for about one minute while the vehicle is traveling at least 6 mph (9.7 km/h) and more than 1-2 minutes have elapsed since the ignition switch has been

turned to on...

Deactivating and Activating the Belt-Minder Feature

WARNING

While the system allows you to deactivate it, this system is designed

to improve your chances of being safely belted and surviving an accident. We recommend you leave the system activated for yourself and others who may use the vehicle. To reduce the risk of injury, do not deactivate or activate the system while driving the vehicle.

Note: The driver and front passenger warning are deactivated and activated independently. When deactivating or activating one seating position, do not buckle the other position as this will terminate the process.

Read Steps 1 - 4 thoroughly before proceeding with the programming procedure.

The system can be deactivated or activated by performing the following procedure:

Before following the procedure, make sure that:

• the parking brake is set

• the transmission selector lever is in

position P (automatic transmission) or N (manual transmission)

• the ignition is off

• the driver and front passenger safety

belts are unbuckled.

1. Turn the ignition on. DO NOT START THE ENGINE.

2. Wait until the safety belt warning light turns off (approximately one minute). After Step 2, wait an additional five seconds before proceeding with Step

3. Once Step 3 is started, the procedure must be completed within 30 seconds.

Safety Belts

3. For the seating position being disabled, buckle then unbuckle the safety belt three times at a moderate speed, ending in the unbuckled state. After Step 3, the safety belt warning light will turn on.

4. While the safety belt warning light is on, buckle and then unbuckle the safety belt. After Step 4, the safety belt warning light will flash for confirmation.

• This will disable the feature for that seating position if it is currently enabled.

• This will enable the feature for that seating position if it is currently disabled.

CHILD RESTRAINT AND SAFETY BELT MAINTENANCE

Inspect the vehicle safety belts and child safety seat systems periodically to make sure they work properly and are not damaged. Inspect the vehicle and child seat safety belts to make sure there are no nicks, tears or cuts. Replace if necessary. All vehicle safety belt assemblies, including retractors, buckles, front safety belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seat back (if equipped), child safety seat LATCH and tether anchors, and attaching hardware, should be inspected after a crash. Read the child restraint manufacturer's instructions for additional inspection and maintenance information specific to the child restraint.

Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a crash be replaced. However, if the crash was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a crash should also be inspected and replaced if either damage or improper operation is noted.

Properly care for safety belts. See Vehicle Care (page 259).

Safety Belts

The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.

Your vehicle's Personal Safety System consists of:

• Driver and passenger dual-stage airbag supplemental restraints.

• Front outboard safety belts with pretensioners, energy management retractors (first row only), and safety belt usage sensors.

• Driver’s seat position sensor.

• Front passenger sensing system.

• Passenger airbag off and on indicator

lamp.

• Front crash severity sensors.

• Restraints control module with impact

and safing sensors.

• Restraint system warning light and backup tone.

• The electrical wiring for the airbags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, front passenger sensing system, and indicator lights.

How Does the Personal Safety System Work?

The Personal Safety System can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the restraints control

module. During a crash, the restraints control module may activate the safety belt pretensioners and may activate either one or both stages of the dual-stage airbag supplemental restraints based on crash severity and occupant conditions.

Personal Safety System™

PRINCIPLE OF OPERATION

WARNINGS

Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close

to the trim covering the airbag module.

All occupants of your vehicle, including the driver, should always

properly wear their safety belts, even when an airbag supplemental restraint system is provided.

Always transport children 12 years

old and under in the back seat and

always properly use appropriate child restraints.

Never place your arm over the airbag

module as a deploying airbag can

result in serious arm fractures or other injuries.

Airbags can kill or injure a child in a

child seat. Never place a rear-facing

child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.

Do not attempt to service, repair, or

modify the airbag supplemental

restraint systems or its fuses. Contact your authorized dealer as soon as possible.

Several airbag system components

get hot after inflation. Do not touch

them after inflation.

If the airbag has deployed, the airbag

will not function again and must be

replaced immediately. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision.

The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag.

Note: You will hear a loud bang and see a cloud of harmless powdery residue if an airbag deploys. This is normal.

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.

While the system is designed to help reduce serious injuries, contact with a deploying airbag may also cause abrasions or swelling. Temporary hearing loss is also a possibility as a result of the noise associated with a deploying airbag. Because airbags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of airbag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the airbag module as possible while maintaining vehicle control.

Routine maintenance of the airbags is not required.

Supplementary Restraints System

SOS POST-CRASH ALERT SYSTEM

The system flashes the turn signal lamps and sounds the horn (intermittently) in the event of a serious impact that deploys an airbag (front, side, side curtain or Safety Canopy) or the safety belt pretensioners.

The horn and lamps will turn off when:

• the hazard control button is pressed

• the panic button (if equipped) is

pressed on the remote entry transmitter, or

• your vehicle runs out of power.

Spin out Detection

If a spinout is detected and the hazard warning flashers come on, the message Spinout Detected Hazards Activated will appear on the instrument cluster.

Once the hazard warning flashers have been activated, they can be turned off by:

• pressing the hazard warning flasher button.

• pressing the remote control unlock button.

• pressing the remote control panic button.

• cycling the ignition on and off twice.

DRIVER AND PASSENGER AIRBAGS

WARNINGS

Never place your arm or any objects over an airbag module. Placing your

arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury.

WARNINGS

Airbags can kill or injure a child in a child seat. Never place a rear-facing

child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.

E151127

The driver and front passenger airbags will deploy during significant frontal and near frontal collisions.

The driver and passenger front airbag system consists of:

• driver and passenger airbag modules.

• front passenger sensing system.

· crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag

Indicator (page 40).

Proper Driver and Front Passenger Seating Adjustment

WARNING

National Highway Traffic Safety

Administration (NHTSA)

recommends a minimum distance of at least 10 inches (25 centimeters) between an occupant’s chest and the driver airbag module.

Supplementary Restraints System

To properly position yourself away from the airbag:

• Move your seat to the rear as far as you can while still reaching the pedals comfortably.

• Recline the seat slightly (one or two degrees) from the upright position.

After all occupants have adjusted their seats and put on safety belts, it is very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seat back, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased.

Children and Airbags

WARNING

Airbags can kill or injure a child in a child seat. Never place a rear-facing

child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.

E142846

Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.

KNEE AIRBAG

The driver's and passenger's knee airbags are located under the instrument panel. The system works along with the driver's and passenger's front airbags to help reduce injury to the legs. When the airbags activate in a collision, the knee airbags deploy from under the instrument panel. As with front and side airbags, it is important to be properly seated and restrained to reduce the risk of death or serious injury.

Make sure the knee airbags are operating properly. See Crash

Sensors and Airbag Indicator

(page 40).

FRONT PASSENGER SENSING SYSTEM

WARNINGS

Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a

rear seating position.

Sitting improperly out of position or with the seat back reclined too far

can take off weight from the seat cushion and affect the decision of the front passenger sensing system, resulting in serious injury or death in a crash

Supplementary Restraints System

WARNINGS

To reduce the risk of possible serious injury: Do not stow objects in seat

back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the passenger airbag off or pass airbag off indicator lamp for proper airbag status. Failure to follow these instructions may interfere with the front passenger seat sensing system.

Any alteration or modification to the

front passenger seat may affect the

performance of the front passenger sensing system.

This system works with sensors that are part of the front passenger’s seat and safety belt to detect the presence of a properly-seated occupant and determine if the front passenger’s frontal airbag should be enabled (may inflate) or not.

E157152

The front passenger sensing system uses a pass airbag off indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. The indicator lamp is located at the top center of the instrument panel.

Note: The indicator lamp will illuminate for a short period of time when the ignition is turned to the on position to confirm it is functional.

The front passenger sensing system is designed to disable (will not inflate) the front passenger's frontal airbag when a rear facing infant seat, a forward-facing child restraint, or a booster seat is detected. Even with this technology, parents are STRONGLY encouraged to always properly restrain children in the rear seat. The sensor also turns off the passenger front airbag and seat-mounted side airbag when the passenger seat is empty.

• When the front passenger sensing system disables (will not inflate) the front passenger frontal airbag, the indicator lamp will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled.

• If the child restraint has been installed and the indicator lamp is not lit, then turn the vehicle off, remove the child restraint from the vehicle and reinstall the restraint following the child restraint manufacturer's instructions.

The front passenger sensing system is designed to enable (may inflate) the front passenger's frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat.

• When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the indicator lamp will be unlit and stay unlit.

Supplementary Restraints System

If a person of adult size is sitting in the front passenger’s seat, but the airbag off indicator lamp is lit, it is possible that the person isn’t sitting properly in the seat. If this happens:

• Turn the vehicle off and ask the person to place the seat back in the full upright position.

• Have the person sit upright in the seat, centered on the seat cushion, with the person’s legs comfortably extended.

• Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’s frontal airbag.

• If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat.

Passenger AirbagPassenger Airbag OFF Indic-

ator

Occupant

DisabledUnlitEmpty

DisabledLitChild

EnabledUnlitAdult

Note: When the passenger airbag off light is illuminated, the passenger (seat mounted) side airbag may be disabled to avoid the risk of airbag deployment injuries.

After all occupants have adjusted their seats and put on safety belts, it’s very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seat back, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased.

If you think that the status of the passenger airbag off indicator lamp is incorrect, check for the following:

• Objects lodged underneath the seat

• Objects between the seat cushion and

the center console (if equipped)

• Objects hanging off the seat back

• Objects stowed in the seatback map

pocket (if equipped)

• Objects placed on the occupant's lap

• Cargo interference with the seat

• Other passengers pushing or pulling on

the seat

• Rear passenger feet and knees resting or pushing on the seat

The conditions listed above may cause the weight of a properly seated occupant to be incorrectly interpreted by the front passenger sensing system. The person in the front passenger seat may appear heavier or lighter due to the conditions described in the list above.

To know if the front passenger sensing system is operating properly, See Crash Sensors

and Airbag Indicator (page 40).

If the airbag readiness light is lit, do the following:

Supplementary Restraints System

The driver and adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat.

If objects are lodged or cargo is interfering with the seat; please take the following steps to remove the obstruction:

• Pull the vehicle over.

• Turn the vehicle off.

• Driver and adult passengers should

check for any objects lodged underneath the front passenger seat or cargo interfering with the seat.

• Remove the obstruction(s) (if found).

• Restart the vehicle.

• Wait at least two minutes and verify

that the airbag readiness light is no longer illuminated.

• If the airbag readiness light remains illuminated, this may or may not be a problem due to the front passenger sensing system.

Do not attempt to repair or service the system; take your vehicle immediately to an authorized dealer.

If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center. See Getting the Services You Need (page

220).

SIDE AIRBAGS

WARNINGS

Do not place objects or mount equipment on or near the airbag

cover, on the side of the seat backs (of the front seats), or in front seat areas that may come into contact with a deploying airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash.

WARNINGS

Do not use accessory seat covers. The use of accessory seat covers

may prevent the deployment of the side airbags and increase the risk of injury in an accident.

Do not lean your head on the door.

The side airbag could injure you as it

deploys from the side of the seat back.

Do not attempt to service, repair, or

modify the airbag, its fuses or the

seat cover on a seat containing an airbag as you could be seriously injured or killed. Contact your authorized dealer as soon as possible.

If the side airbag has deployed, the

airbag will not function again. The

side airbag system (including the seat) must be inspected and serviced by an authorized dealer. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a crash.

The side airbags are located on the outboard side of the seat backs of the front seats. In certain lateral crashes, the airbag on the side affected by the crash will be inflated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact crashes.

E152533

Supplementary Restraints System

The system consists of the following:

• A label or embossed side panel indicating that side airbags are fitted to your vehicle

• Side airbags located inside the driver and front passenger seat backs

• Front passenger sensing system

·Crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag

Indicator (page 40). Note: The passenger sensing system will

deactivate the passenger seat-mounted side airbag if it detects an empty passenger seat.

The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags.

SIDE CURTAIN AIRBAGS

WARNINGS

Do not place objects or mount equipment on or near the headliner

at the siderail that may come into contact with a deploying side curtain airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash.

Do not lean your head on the door.

The side curtain airbag could injure

you as it deploys from the headliner.

Do not attempt to service, repair, or

modify the side curtain airbags, its

fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing side curtain airbags. Contact your authorized dealer as soon as possible.

WARNINGS

All occupants of the vehicle including the driver should always wear their

safety belts even when an airbag supplemental restraint system and side curtain airbag is provided.

To reduce risk of injury, do not

obstruct or place objects in the

deployment path of the side curtain airbag.

If the side curtain airbags have

deployed, the side curtain airbags

will not function again. The side curtain airbags (including the A, B and C pillar trim and headliner) must be inspected and serviced by an authorized dealer. If the side curtain airbag is not replaced, the unrepaired area will increase the risk of injury in a crash.

The side curtain airbags will deploy during significant side crashes. The side curtain airbags are mounted to the roof side-rail sheet metal, behind the headliner, above each row of seats. In certain lateral crashes, the side curtain airbags on the impacted side of the vehicle will be activated. The side curtain airbags are designed to inflate between the side window area and occupants to further enhance protection provided in side impact crashes.

The system consists of the following:

E75004

Supplementary Restraints System

• Side curtain airbags located above the trim panels over the front and rear side windows identified by a label or wording on the headliner or roof-pillar trim.

• A flexible headliner which opens above the side doors to allow side air curtain deployment.

Crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag

Indicator (page 40).

Children 12 years old and under should always be properly restrained in the back seats. The side curtain airbags will not interfere with children restrained using a properly installed child or booster seat because it is designed to inflate downward from the headliner above the doors along the side window opening.

The design and development of the side curtain airbags included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side curtain airbags.

CRASH SENSORS AND AIRBAG INDICATOR

WARNING

Modifying or adding equipment to the front end of the vehicle (including

frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury. Do not modify the front end of the vehicle.

The vehicle has a collection of crash and occupant sensors which provide information to the restraints control module which deploys (activates) the front safety belt pretensioners, driver airbag, passenger airbag, knee airbag(s), seat mounted side airbags, and the side curtain airbags. Based on the type of crash (frontal impact or side impact), the restraints control module will deploy the appropriate safety devices.

The restraints control module also monitors the readiness of the above safety devices plus the crash and occupant sensors. The readiness of the safety system is indicated by a warning indicator light in the instrument cluster or by a backup tone if the warning light is not working. Routine maintenance of the airbag is not required.

A difficulty with the system is indicated by one or more of the following:

· The readiness light will not illuminate immediately after the ignition is turned on.

• The readiness light will either flash or stay lit.

• A series of five beeps will be heard. The tone pattern will repeat periodically until the problem, the light or both are repaired.

If any of these things happen, even intermittently, have the supplemental restraint system serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a crash.

The safety belt pretensioners and the front airbag supplemental restraint system are designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the restraints control module to deploy a safety device.

Supplementary Restraints System

The fact that the safety belt pretensioners or front airbags did not activate for both front seat occupants in a crash does not mean that something is wrong with the system. Rather, it means the restraints control module determined the accident conditions (crash severity, belt usage) were not appropriate to activate these safety devices.

• Front airbags are designed to activate only in frontal and near-frontal crashes (not rollovers, side impacts or rear impacts) unless the crash causes sufficient longitudinal deceleration.

• The safety belt pretensioners are designed to activate in frontal and near-frontal crashes, and may also activate when a side curtain deploys.

• A knee airbag deploys from under the instrument panel when the front airbag activates in a crash.

• Side airbags and side curtain airbags are designed to inflate in side-impact crashes, not rollovers, rear impacts, frontal or near-frontal crashes, unless the crash causes sufficient lateral deceleration.

AIRBAG DISPOSAL

Contact your authorized dealer as soon as possible. Airbags MUST BE disposed of by qualified personnel.

Supplementary Restraints System

GENERAL INFORMATION ON RADIO FREQUENCIES

This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Note: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term IC before the radio certification number only signifies that Industry Canada technical specifications were met.

The typical operating range for your transmitter is approximately 33 feet (10 meters). Vehicles with the remote start feature will have a greater range. One of the following could cause a decrease in operating range:

• weather conditions

• nearby radio towers

• structures around the vehicle

• other vehicles parked next to your

vehicle

The radio frequency used by your remote control can also be used by other short distance radio transmissions, for example amateur radios, medical equipment, wireless headphones, remote controls and alarm systems. If the frequencies are jammed, you will not be able to use your remote control. You can lock and unlock the doors with the key.

Note: Make sure to lock your vehicle before leaving it unattended.

Note: If you are in range, the remote control will operate if you press any button unintentionally.

Intelligent Access (If Equipped)

The system uses a radio frequency signal to communicate with your vehicle and authorize your vehicle to unlock when one of the following conditions are met:

• You touch the inside of the front exterior door handle.

• You press the luggage compartment button.

• You press a button on the transmitter.

If excessive radio frequency interference is present in the area or if the transmitter battery is low, you may need to mechanically unlock your door. You can use the mechanical key blade in your intelligent access key to open the driver door in this situation. See Remote

Control (page 42).

REMOTE CONTROL

Integrated Keyhead Transmitters

(If Equipped)

Use the key blade is used to start the vehicle and unlock or lock the driver’s door from outside the vehicle. The transmitter portion functions as the remote control.

E151797

Press the button to release the key. Press and hold the button to fold the key back in when not in use.

Keys and Remote Controls

E151795

Note: Your vehicle’s keys came with a security tag that provides important vehicle key cut information. Keep the tag in a safe place for future reference.

Intelligent Access Key (If Equipped)

E144506

Your intelligent access keys operate the power locks and the remote start system. The key must be in your vehicle to activate the push-button start system.

Removable Key Blade

The intelligent access key also contains a removable mechanical key blade that you can use to unlock the driver door.

E151796

Slide the release on the back of the remote control and pivot the cover off to access the key blade.

E151795

Note: Your vehicle’s backup keys came with a security tag that provides important vehicle key cut information. Keep the tag in a safe place for future reference.

Using the Key Blade

The key cylinder is hidden under a cap on the driver door handle.

To remove the cap:

E151956

Keys and Remote Controls

1. Insert the key blade into the slot on the bottom of the handle and press up.

2. While maintaining upward pressure, move the cap rearward to release it. Gently remove the key while doing so.

To install the cap:

E151957

1. Place the cap just forward of the key cylinder.

2. While applying pressure to the cap, move it forward until it is in place. You may hear a snap as it engages.

Make sure the cap is properly installed by trying to move it rearward.

Replacing the Battery

Note: Refer to local regulations when

disposing of transmitter batteries. Note: Do not wipe off any grease on the

battery terminals or on the back surface of the circuit board.

Note: Replacing the battery will not delete the transmitter from the vehicle. The transmitter should operate normally.

A message will appear in the information display when the remote control battery is low. See Information Messages (page

90).

Integrated Keyhead Transmitter

The remote control uses one coin-type three-volt lithium battery CR2032 or equivalent.

Press the button to release the key before beginning the procedure.

E151798

1. Insert a screwdriver in the position shown and gently push the clip.

2. Press the clip down to release the battery cover.

E151799

3. Carefully remove the cover.

Keys and Remote Controls

Note: Do not touch the battery contacts or

the printed circuit board with the screwdriver.

4. Insert a screwdriver as shown to release the battery.

E151801

5. Remove the battery.

6. Install a new battery with the + facing up.

7. Replace the battery cover.

Intelligent Access Transmitter

The remote control uses two coin-type three-volt lithium batteries CR2025 or equivalent.

E151796

1. Slide the release on the back of the remote control and pivot the cover off.

E153890

2. Insert a coin into the slot and twist to separate the housing.

E153891

3. Remove the batteries.

4. Install new batteries with the + facing each other.

Note: Make sure to replace the label between the two batteries.

Keys and Remote Controls

5. Reinstall the housing and cover.

Car Finder

E138623

Press the button twice within three seconds. The horn will

sound and the turn signals will flash. It is recommended that this method be used to locate your vehicle, rather than using the panic alarm.

Sounding a Panic Alarm

Note: The panic alarm will only operate

when the ignition is off.

E138624

Press the button to activate the

alarm. Press the button again or

turn the ignition on to deactivate.

Remote Start (If Equipped)

WARNING

To avoid exhaust fumes, do not use remote start if your vehicle is parked indoors or areas that are not well

ventilated.

Note: Do not use remote start if your vehicle is low on fuel.

E138625

Your vehicle has remote start if

the transmitter has this button.

The remote start feature allows you to start your vehicle from outside the vehicle. The transmitter has an extended operating range.

Vehicles with automatic climate control can be configured to operate when the vehicle is remote started. See Climate Control (page 118). A manual climate control system will run at the setting it was set to when the vehicle was last turned off.

Many states and provinces have restrictions for the use of remote start. Check your local and state or provincial laws for specific requirements regarding remote start systems.

The remote start system will not work if:

• the ignition is on

• the alarm system triggered

• you disable the feature

• the hood is open

• the transmission is not in P

• the vehicle battery voltage is too low

• the service engine soon light is on.

Remote Control Feedback

An LED on the remote control provides status feedback of remote start or stop commands.

StatusLED

Remote start or

extension

successful

Solid green

Remote stop

successful; engine

off

Solid red

Remote start or

stop failed

Blinking red

Waiting for status

update

Blinking green

Remote Starting the Vehicle

Note: Each button press must be done

within three seconds of each other. The vehicle will not remote start if this sequence is not followed and the horn will not sound.

Keys and Remote Controls

E138626

The tag with your transmitter details the starting procedure. To remote start the vehicle:

1. Press the lock button to lock all the doors.

2. Press the remote start button twice. The exterior lamps will flash twice.

The horn will sound if the system fails to start, unless quiet start is on. Quiet start will run the blower fan at a slower speed to reduce noise. It can be switched on or off in the information display. See General

Information (page 82). Note: If the vehicle has been remote started

and is equipped with an integrated keyhead transmitter, you must turn the ignition on before driving the vehicle. If equipped with an intelligent access transmitter, you must press the START/STOP button on the instrument panel once while applying the brake pedal before driving your vehicle.

The power windows will be inhibited during the remote start and the radio will not turn on automatically.

The parking lamps will remain on and the engine will run for 5, 10, or 15 minutes, depending on the setting.

Extending the Vehicle Run Time

Repeat Steps 1 and 2 with the vehicle still running to extend the run time for another remote start duration. If you programmed the duration to last 10 minutes, the second 10 minutes will begin after what is left of the first activation time. For example, if the vehicle had been running from the first remote start for five minutes, the vehicle will continue to run now for a total of 15 minutes.

Wait at least five seconds before remote starting after a vehicle shutdown.

Turning the Vehicle Off After Remote Starting

E138625

Press the button once. The parking lamps will turn off.

You may have to be closer to the vehicle than when starting due to ground reflection and the added noise of the running vehicle.

You can disable or enable the remote start system through the information display. See General Information (page 82).

REPLACING A LOST KEY OR REMOTE CONTROL

Replacement keys or remote controls can be purchased from an authorized dealer. Authorized dealers can program remote controls for your vehicle. See Passive Anti-Theft System (page 58).

To re-program the passive anti-theft system see an authorized dealer.

Keys and Remote Controls

PRINCIPLE OF OPERATION

MyKey allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to the vehicle can be activated with these restricted modes. Any keys that have not been programmed are referred to as an "administrator key" or "admin key" which can be used to:

• create a restricted key

• program optional MyKey settings

• clear all MyKey features altogether.

Once a key has been programmed you can access the following information using the information display control:

• How many admin keys and MyKeys are programmed to the vehicle.

• The total distance the vehicle has been driven with a MyKey.

For vehicles equipped with intelligent access key (push button start), when both a MyKey and an admin intelligent access key (fob) are present, the admin fob will be recognized by the vehicle to start the engine.

Standard Settings

These settings cannot be changed.

• Belt-Minder®. This cannot be disabled and the five-minute timer does not expire. The audio system is muted when MyKey Belt-Minder® is activated.

• Early low fuel. Warnings are displayed in the information display control followed by an audible tone when the fuel tank is at one-eighth tank or less.

• Driver assist features, if equipped on your vehicle, are forced on: Rear parking aid, Blind spot information system (BLIS®) with cross traffic alert, Lane departure warning, Forward collision warning system and Satellite radio adult content restriction.

Optional Settings

These settings can be configured right after a MyKey is first created or changed afterward with an admin key.

• Vehicle speed limit of 65, 70, 75 and 80 mph (105, 113, 121 and 130 km/h). Visual warnings are displayed followed by an audible tone when vehicle speed has reached the selected top speed.

• Vehicle speed minder of 45, 55 or 65 mph (75, 90, or 105 km/h). Visual warnings are displayed followed by an audible tone when the preselected vehicle speed is exceeded.

• Audio system maximum volume of 45%. A message in the audio system is displayed when attempting to exceed the limited volume. Also, speed sensitive compensated volume feature will be disabled.

• Always on setting. When this is selected you will not be able to disable AdvanceTrac®, 911 Assist® or the Do not disturb feature (if your vehicle is equipped with these features).

CREATING A MYKEY

Use the information display control to create a MyKey:

1. Insert the key you want to program into the ignition or, if the vehicle is equipped with push button start, put the intelligent access key in the backup slot. Backup slot information is located in a different chapter. See Starting and Stopping the Engine (page 143).

2. Turn the ignition on.

3. Access the main menu on the information display controls and select Settings, then MyKey by pressing OK or the > button.

4. Press OK to select Create.

MyKey™ (If Equipped)

5. When prompted, hold the OK button until you see a message informing you to label this key as a MyKey. The key will be restricted at the next start.

The key is successfully programmed. Make sure you label it so you can distinguish it from the admin keys.

You can program optional settings for the key(s). Refer to Programming/Changing

optional settings.

Programming/Changing Optional Settings

All programmed keys can be cleared within the same key cycle in which a key was programmed, otherwise an admin key is required to clear the keys. See Clearing All MyKeys (page 49).

You can access the optional settings through the information display control.

1. Turn the ignition on using an admin key.

2. Access the main menu and select Settings, then MyKey.

3. Use the arrow buttons to get to an optional feature.

4. Press OK or > to scroll through settings.

5. Press OK or > to make a selection.

CLEARING ALL MYKEYS

All programmed MyKeys can be cleared within the same key cycle in which a MyKey was created, otherwise an admin key is required to clear the keys.

To clear all MyKeys (which removes all restrictions and returns them to admin key status), use the information display to do the following:

1. Access the main menu and select Settings, then MyKey.

2. Scroll to Clear All and press the OK button.

3. Hold the OK button until ALL

MYKEYS CLEARED is displayed.

CHECKING MYKEY SYSTEM STATUS

The information display control displays information about keys programmed to the vehicle:

• MYKEY MILES: Tracks mileage when a restricted key is used. If mileage does not accumulate as expected, then the key is not being used by the intended user. The only way to reset this to zero is by clearing MyKeys. If the mileage is lower than the last time you checked, then the key system has been recently reset.

• #MYKEY(S): Indicates how many restricted keys are programmed to the vehicle. Can also be used to detect deletion of a restricted key.

• #ADMIN KEY(S): Indicates how many admin keys are programmed to the vehicle. Can also be used to detect if an additional key has been programmed to the vehicle.

USING MYKEY WITH REMOTE START SYSTEMS

MyKey is NOT compatible with non-Ford-approved aftermarket remote start systems. If you choose to install a remote start system please see your Ford authorized dealer for a Ford-approved remote start system.

MyKey™ (If Equipped)

MYKEY TROUBLESHOOTING

Potential CausesCondition

· The key in the ignition does not have admin privileges.

I cannot program a key.

· The key in the ignition is the only admin key (there always has to be at least one admin key).

· The intelligent access key is not in the backup slot (vehicles with push-button start).

· SecuriLock® passive anti-theft system is disabled or in unlimited mode.

· The key in the ignition does not have admin privileges. I cannot program the optional settings.

I cannot program the optional settings.

· No keys are programmed to the vehicle. See Creating a MyKey (page 48).

· The key in the ignition does not have admin privileges.

I cannot clear the restricted keys.

· No restricted keys are programmed to the vehicle. See Creating a MyKey (page 48).

· Purchase a new key from your authorized dealer.

I lost the only admin key.

· Program a spare key. See Passive Anti- Theft System (page 58).

I lost a key.

· An admin fob is present at engine startup.

No restricted key functions with intelligent access key (push-button start).

· No MyKey keys are programmed to the vehicle. See Creating a MyKey (page 48).

· The MyKey key is not being used by the intended user.

MyKey miles do not accumulate.

· The key system has been reset.

MyKey™ (If Equipped)

LOCKING AND UNLOCKING

You can use the power door lock control or the remote control to lock and unlock the vehicle.

Power Door Locks

The power door lock control is on the driver and front passenger door panels.

E138628

UnlockA LockB

Door Lock Indicator

An LED on each door window trim will light when you lock the door. It will remain lit for up to 10 minutes after you switch off the ignition.

Switch Inhibitor

When you electronically lock your vehicle, the power door lock switch will no longer operate after 20 seconds. You must unlock your vehicle with the remote control or keyless keypad, or switch the ignition on, to restore function to these switches. You can switch this feature on or off in the information display. See General

Information (page 82).

Rear Door Unlocking and Opening

Pull the interior door release handle twice to unlock and open the rear door. The first pull unlocks the door and the second pull will unlatch the door.

Remote Control

You can use the remote control at any time. The luggage compartment release button will only work when the vehicle speed is less than 5 mph (8 km/h).

Unlocking the Doors (Two-Stage Unlock)

E138629

Press the button to unlock the driver door.

Press the button again within three seconds to unlock all doors. The turn signals will flash.

Press and hold both the lock and unlock buttons on the remote control for three seconds to change between driver door or all doors unlock mode. The turn signals will flash twice to indicate a change to the unlocking mode. Driver door unlock mode will only unlock the driver door when the unlock button is pressed once. All door unlock mode will unlock all doors with one press of the unlock button. The unlocking mode applies to the remote control, keyless entry keypad and intelligent access. You can also change the mode in the information display. See General

Information (page 82).

Locking the Doors

E138623

Press the button to lock all the

doors. The turn signals will

illuminate. Press the button again within three

seconds to confirm that all the doors are closed. The doors will lock again, the horn will sound and the turn signals will illuminate if all the doors and the luggage compartment are closed.

Locks

Mislock

If any door or the luggage compartment is open, or if the hood is open on vehicles with an anti-theft alarm or remote start, the horn will sound twice and the lamps will not flash. You can enable or disable this feature in the information display. See

General Information (page 82).

Opening the Luggage Compartment

E138630

Press twice within three seconds to open the luggage compartment.

Make sure to close and latch the luggage compartment before driving your vehicle. An unlatched luggage compartment may cause objects to fall out or block your view.

Activating Intelligent Access (If

Equipped)

You must have the intelligent access key within 3 feet (1 meter) of your vehicle.

At a Door

Pull an exterior door handle to unlock and open the door. Make sure not to touch the lock sensor on top of the handle.

E157085

Touch the top of the door handle to lock your vehicle.

At the Luggage Compartment

E144402

Press the exterior release button hidden above the license plate.

Smart Unlocks For Integrated Keyhead Transmitter

This feature helps to prevent you from locking yourself out of your vehicle if your key is still in the ignition.

When you open one of the front doors and lock the vehicle with the power door lock control, all the doors will lock then unlock and the horn will sound twice if your key is still in the ignition.

Your vehicle can still be locked with the key in the ignition by using the keyless entry keypad with the driver door closed, or by pressing the lock button on the transmitter even if the doors are not closed.

If both front doors are closed, the vehicle can be locked by any method, regardless of whether the key is in the ignition or not.

Smart Unlocks For Intelligent Access Keys (If Equipped)

This feature helps to prevent you from unintentionally locking your intelligent access key inside your vehicle’ s passenger compartment or rear cargo area.

Locks

When you electronically lock your vehicle using the driver or passenger power door lock control (with any door open, vehicle in park and ignition off), the vehicle will search for an intelligent access key in the passenger compartment after you close the last door. If your vehicle finds a key, all of the doors will immediately unlock and the horn will sound twice, indicating that a key is inside.

You can override the smart unlock feature and intentionally lock the intelligent access key inside your vehicle. To do this, lock your vehicle after all doors are closed by:

• using the keyless entry keypad

• pressing the lock button on another

intelligent access key

• touching the locking area on the handle with another intelligent access key in your hand.

When you open one of the front doors and lock your vehicle using the power door lock control, all doors will lock then unlock if:

• the ignition is on, or

• the ignition is off and your vehicle is not

in P.

Auto Relock

If you press the unlock button on the remote control and do not open a door within 45 seconds, your vehicle will lock and the alarm will arm. You can enable or disable this feature in the information display. See General Information (page

82).

Autolock Feature

The autolock feature will lock all the doors when:

• all doors are closed,

• the ignition is on,

• you shift into any gear putting your

vehicle in motion, and

• your vehicle attains a speed greater than 12 mph (20 km/h).

The autolock feature repeats when:

• you open then close any door while the ignition is on and your vehicle speed is 9 mph (15 km/h) or lower, and

• your vehicle then attains a speed greater than 12 mph (20 km/h).

Autounlock Feature

The autounlock feature will unlock all the doors when:

• the ignition is on, all the doors are closed, and your vehicle has been in motion at a speed greater than 12 mph (20 km/h);

• your vehicle comes to a stop and you switch the ignition off or to accessory; and

• you open the driver door within 10 minutes of the switching the ignition off or to accessory.

Note: The doors will not autounlock if you electronically lock your vehicle after you switch the ignition off and before you open the driver door.

Enabling or Disabling

Note: You can enable or disable the

autolock and autounlock features independently of each other.

You can enable or disable these features in the information display or your authorized dealer can do it for you. See

General Information (page 82).

Illuminated Entry

The interior lamps and select exterior lamps will illuminate when you unlock the doors with the remote entry system.

Locks

The illuminated entry system will turn off the lights if:

• the ignition is on,

• you press the remote control lock

button, or

• after 25 seconds of illumination. The lights will not turn off if:

• you turn them on with the dimmer control, or

• any door is open.

Illuminated Exit

The interior lamps and select exterior lamps will illuminate when all doors are closed, you switch the ignition off and you remove the key from the ignition (integrated keyhead transmitter only).

The lamps will turn off if all the doors remain closed and:

• 25 seconds elapse

• you insert the key in the ignition

(integrated keyhead transmitter only)

• you press the START/STOP button (intelligent access key only).

Battery Saver

If you leave the courtesy lamps, dome lamps or headlamps on, the battery saver will shut them off 10 minutes after you switch the ignition off.

Accessory Mode Battery Saver for Intelligent Access Keys (If Equipped)

If you leave your vehicle in the run ignition state, it will shut off once it detects a certain amount of battery drain or after 45 minutes.

Luggage Compartment

With the Remote Control

E138630

Press twice within three seconds to unlatch the trunk.

From Outside Your Vehicle

E144402

Press the release button above the license plate to unlatch the trunk. Your vehicle must be unlocked or have an intelligent access transmitter within 3 feet (1 meter) of the trunk.

KEYLESS ENTRY (IF EQUIPPED)

SECURICODE™ KEYLESS ENTRY KEYPAD

The keypad is located near the driver window. It is invisible until touched and then it lights up so you can see and touch the appropriate buttons.

Note: If you enter your entry code too fast on the keypad, the unlock function may not work. Re-enter your entry code more slowly.

Locks

E138637

You can use the keypad to:

• lock or unlock the doors

• release the trunk

• recall memory seat and mirror

positions (if equipped)

• program and erase user codes

• arm and disarm the anti-theft alarm.

You can operate the keypad with the factory-set 5-digit entry code. The code is located on the owner’s wallet card in the glove box and is available from an authorized dealer. You can also create up to five of your own 5-digit personal entry codes.

Programming a Personal Entry Code

To create your own personal entry code:

1. Enter the factory-set code.

2. Press 1·2 on the keypad within five seconds.

3. Enter your personal 5-digit code. You must enter each number within five seconds of each other.

4. Press 1·2 on the keypad to save personal code 1.

The doors will lock then unlock to confirm that programming was successful.

To program additional personal entry codes, repeat Steps 1-3, then for Step 4:

• press 3·4 to save personal code 2

• press 5·6 to save personal code 3

• press 7·8 to save personal code 4

• press 9·0 to save personal code 5.

You may also program a personal entry code through the MyFord Touch system (if equipped).

Tips:

• Do not set a code that uses five of the same number.

• Do not use five numbers in sequential order.

• The factory-set code will work even if you have set your own personal code.

Recalling Memory Positions (If Equipped)

The programmed entry codes will recall driver memory positions as follows:

• Entry code 1 will recall driver 1 memory positions.

• Entry code 2 will recall driver 2 memory positions.

• Entry code 3 will recall driver 3 memory positions.

Note: Personal entry codes 4 and 5 will not recall memory positions.

Erasing a Personal Code

1. Enter the factory-set 5-digit code.

2. Press and release 1·2 on the keypad within five seconds.

3. Press and hold 1·2 for two seconds. You must do this within five seconds of completing Step 2.

All personal codes are now erased and only the factory-set 5–digit code will work.

Locks

Anti-Scan Feature

The keypad will go into an anti-scan mode if you enter the wrong code seven times (35 consecutive button presses). This mode disables the keypad for one minute and the keypad lamp will flash.

The anti-scan feature will turn off after:

• one minute of keypad inactivity

• pressing the unlock button on the

remote control

• switching the ignition on

• unlocking your vehicle using intelligent

access.

Unlocking and Locking the Doors

To Unlock the Driver Door

Enter the factory-set 5-digit code or your personal code. You must press each number within five seconds of each other. The interior lamps will illuminate.

Note: All doors will unlock if you enable the all-door unlocking mode. See Locking and

Unlocking (page 51).

To Unlock All Doors

Enter the factory-set code or your personal code, then press 3·4 within five seconds.

To Lock All Doors

Press and hold 7·8 and 9·0 at the same time (with the driver door closed). You do not need to enter the keypad code first.

To Release the Trunk

Enter the factory-set code or your personal code, then press 5·6 within five seconds.

Displaying the Factory Set Code

With Integrated Keyhead Transmitters

Note: You will need to have two programmed passive anti-theft keys for this procedure.

To display the factory-set code in the information display:

1. Insert a key into the ignition and switch the ignition on for a few seconds.

2. Switch the ignition off and remove the key.

3. Insert the second key into the ignition and switch the ignition on.

The factory-set code will display for a few seconds.

Note: The code may not display until after any other warning messages first display.

With Intelligent Access Keys

Note: You will need to have two programmed intelligent access keys for this procedure.

To display the factory-set code in the information display:

E147165

1. Place the first programmed key in the backup slot inside the center console. The key ring must be at the top with the buttons facing toward the rear.

2. Press the START/STOP button once and wait a few seconds.

3. Press the START/STOP button again and remove the key.

4. Insert the second programmed key into the backup slot, then press the START/STOP button.

Locks

The factory-set code will appear in the information display for a few seconds.

Note: The code may not display until after any other warning messages first display.

INTERIOR LUGGAGE COMPARTMENT RELEASE

WARNINGS

Keep vehicle doors and luggage compartment locked and keep keys

and remote transmitters out of a child’s reach. Unsupervised children could lock themselves in the trunk and risk injury. Children should be taught not to play in vehicles.

Do not leave children, unreliable

adults, or animals unattended in the

vehicle. On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people or animals to these high temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are particularly at risk.

Your vehicle is equipped with a release handle that provides a means of escape for children and adults if they become locked inside the luggage compartment.

Adults should familiarize themselves with the operation and location of the release handle.

E144403

The handle is located inside the luggage compartment either on the luggage compartment door (lid) or near the tail lamps. It is composed of a material that will glow for hours in darkness following brief exposure to ambient light.

Pull the handle and push up on the luggage compartment door (lid) to open from within the luggage compartment.

Locks

PASSIVE ANTI-THEFT SYSTEM

Note: The system is not compatible with

non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.

Note: Metallic objects, electronic devices or a second coded key on the same key chain may cause vehicle starting problems if they are too close to the key when starting the engine. Prevent these objects from touching the coded key while starting the engine. Switch the ignition off, move all objects on the key chain away from the coded key and restart the engine if a problem occurs.

Note: Do not leave a duplicate coded key in the vehicle. Always take your keys and lock all doors when leaving the vehicle.

SecuriLock®

The system is an engine immobilization system. It is designed to help prevent the engine from starting unless you use a coded key programmed to your vehicle. Using the wrong key may prevent the engine from starting. A message may appear in the information display.

If you are unable to start the engine with a correctly coded key, a malfunction has happened and a message may appear in the information display.

Automatic Arming

The vehicle arms immediately after switching the ignition off.

Automatic Disarming

Switching the ignition on with a coded key disarms the vehicle.

Replacement Keys

Note: Your vehicle comes equipped with

two integrated keyhead transmitters or two intelligent access keys.

The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts the vehicle, as well as a remote control.

The intelligent access key functions as a programmed key that operates the driver door lock and activates the intelligent access with push button start system, as well as a remote control.

If your programmed transmitters or standard SecuriLock coded keys (integrated keyhead transmitters only) are lost or stolen and you do not have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed.

Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. See your authorized dealer to purchase additional spare or replacement keys.

Programming a Spare Integrated Keyhead Transmitter

Note: You can program a maximum of eight

coded keys to your vehicle. All eight can be integrated keyhead transmitters.

You can program your own integrated keyhead transmitter or standard SecuriLock coded keys to your vehicle. This procedure will program both the engine immobilizer keycode and the remote entry portion of the remote control to your vehicle.

Only use integrated keyhead transmitters or standard SecuriLock keys.

Security

You must have two previously programmed coded keys and the new unprogrammed key readily accessible. See an authorized dealer to have the spare key programmed if two previously programmed coded keys are not available.

Read and understand the entire procedure before you begin.

1. Insert the first previously programmed

coded key into the ignition.

2. Switch the ignition from off to on. Keep

the ignition on for at least three seconds, but no more than 10 seconds.

3. Switch the ignition off and remove the

first coded key from the ignition.

4. After three seconds but within 10

seconds of switching the ignition off, insert the second previously coded key into the ignition.

5. Switch the ignition from off to on. Keep

the ignition on for at least three seconds, but no more than 10 seconds.

6. Switch the ignition off and remove the

second previously programmed coded key from the ignition.

7. After three seconds but within 10

seconds of switching the ignition off and removing the previously programmed coded key, insert the new unprogrammed key into the ignition.

8. Switch the ignition from off to on. Keep

the ignition on for at least six seconds.

9. Remove the newly programmed coded

key from the ignition.

If the key has been successfully programmed it will start the engine and operate the remote entry system (if the new key is an integrated keyhead transmitter).

If it was not programmed successfully, wait 10 seconds and repeat Steps 1 through

8. If you are still unsuccessful, take your vehicle to an authorized dealer.

Programming a Spare Intelligent Access Key

Note: You can program a maximum for four

intelligent access keys to your vehicle.

You must have two previously programmed intelligent access keys inside your vehicle and the new unprogrammed intelligent access keys readily accessible. See an authorized dealer to have the spare key programmed if two previously programmed keys are not available.

Make sure that the vehicle is off before beginning this procedure. Make sure that you close all the doors before beginning and that they remain closed throughout the procedure. Perform all steps within 30 seconds of starting the sequence. Stop and wait for at least one minute before starting again if you perform any steps out of sequence.

Read and understand the entire procedure before you begin.

E147165

1. Place a programmed intelligent access key in the backup slot in the center console. The key ring must be at the top with the buttons facing toward the rear.

2. Wait 5 seconds, then press the START/STOP button.

3. Remove the intelligent access key.

Security

4. Within 10 seconds, place a second programmed intelligent access key in the backup slot and press the START/STOP button.

5. Wait 5 seconds, then press the START/STOP button again.

6. Remove the intelligent access key.

7. Wait 5 seconds, then place the unprogrammed intelligent access key in the backup slot and press the START/STOP button.

Programming is now complete. Verify the remote control functions operate and the vehicle starts with the new intelligent access key.

If programming was not successful, wait 10 seconds and repeat Steps 1 through 7. If you are still unsuccessful, take your vehicle to your authorized dealer.

ANTI-THEFT ALARM

The system will warn you of an unauthorized entry to your vehicle. It will be triggered if any door, the luggage compartment or the hood is opened without using the key, remote control or keyless entry keypad.

The direction indicators will flash and the horn will sound if unauthorized entry is attempted while the alarm is armed.

Take all remote controls to an authorized dealer if there is any potential alarm problem with your vehicle.

Arming the Alarm

The alarm is ready to arm when there is not a key in the ignition. Electronically lock the vehicle to arm the alarm.

Disarming the Alarm

Disarm the alarm by any of the following actions:

• Unlock the doors or luggage compartment with the remote control or keyless entry keypad.

• Switch the ignition on or start the vehicle.

• Use a key in the driver’s door to unlock the vehicle, then switch the ignition on within 12 seconds.

Note: Pressing the panic button on the remote control will stop the horn and signal indicators, but will not disarm the system.

Security

ADJUSTING THE STEERING WHEEL

WARNING

Do not adjust the steering wheel when your vehicle is moving.

Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 129).

E157083

1. Unlock the steering column.

2. Adjust the steering wheel to the desired position.

E157084

3. Lock the steering column.

AUDIO CONTROL (IF EQUIPPED)

You can operate the following functions with the control:

E144503

Volume upA Volume downB MuteC MediaD Seek down or previousE Seek up or nextF

MEDIA

Press repeatedly to scroll through available audio sources.

Seek, Next or Previous

Press the seek button to:

• tune the radio to the next or previous stored preset

• play the next or the previous track.

Press and hold the seek button to:

• tune the radio to the next station up or down the frequency band

• seek through a track.

Steering Wheel

VOICE CONTROL (IF EQUIPPED)

E144504

End a callA Answer a callB Voice recognitionC

See SYNC™ (page 303). See MyFord

Touch™ (page 341).

CRUISE CONTROL

Type 1

E144500

Type 2

E144501

See Cruise Control (page 185).

INFORMATION DISPLAY CONTROL

E144636

See Information Displays (page 82).

Steering Wheel

Cluster Display Control Features

E144811

If equipped with: MyFord system: This control functions

the same as the center control on the faceplate. See Audio unit (page 106).

MyFord Touch: Use this control to adjust the right side of the cluster display. Navigate through the screen and press OK to select. See MyFord Touch™ (page

341).

Steering Wheel

WINDSHIELD WIPERS

Note: Fully defrost the windshield before

switching on the windshield wipers. Note: Make sure the windshield wipers are

switched off before entering a car wash. Note: Clean the windshield and wiper

blades if they begin to leave streaks or smears. If that doesn't resolve the issue, install new wiper blades.

Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washers before wiping a dry windshield.

E144495

Single wipeA Intermittent wipeB Normal wipeC High speed wipeD

Intermittent Wipe

E144496

Shortest wipe intervalA Intermittent wipeB Longest wipe intervalC

Use the rotary control to adjust the intermittent wipe interval.

Speed Dependent Wipers

When your vehicle speed increases, the interval between wipes will decrease.

AUTOWIPERS (IF EQUIPPED)

Note: Fully defrost the windshield before

switching on the windshield wipers. Note: Make sure the windshield wipers are

switched off before entering a car wash. Note: Clean the windshield and wiper

blades if they begin to leave streaks or smears. If that doesn't resolve the issue, install new wiper blades.

Note: If you switch autolamps on in conjunction with autowipers, your low beam headlamps will illuminate automatically when the rain sensor activates the windshield wipers continuously.

Note: Wet road conditions can cause unexpected wiping or smearing.

Wipers and Washers

To reduce smearing we recommend the following:

• Lower the sensitivity of the autowipers.

• Switch to normal or high speed wipe.

• Switch the autowipers off.

E144497

Highest sensitivityA OnB Lowest sensitivityC

The wipers will function when moisture is detected on the windshield. The rain sensor will continue to monitor the amount of moisture on the windshield and adjust the speed of the wipers automatically. This feature can be switched on or off in the information display. See General Information (page 82).

Use the rotary control to adjust the sensitivity of the rain sensor. With low sensitivity, the wipers will operate when the sensor detects a large amount of moisture on the windshield. With high sensitivity, the wipers will operate when the sensor detects a small amount of moisture on the windshield.

Keep the outside of the windshield clean. Sensor performance will be affected if the area around the interior mirror is dirty. The rain sensor is very sensitive and the wipers may operate if dirt, mist or flies hit the windshield.

WINDSHIELD WASHERS

Note: Do not operate the washers when

the washer reservoir is empty. This may cause the washer pump to overheat.

E144498

The washers will spray for as long as you pull the lever toward you. When you release the lever, the wipers will operate for a short time.

A wipe will occur a few seconds after washing to clear any remaining washer fluid. This feature can be switched on or off in the information display. See General Information (page 82).

Wipers and Washers

LIGHTING CONTROL

E142449

OffA Parking lamps, instrument panel

lamps, license plate lamps and tail lamps

HeadlampsC

High Beams

E130140

Push the lever forward to switch the high beams on.

Push the lever forward again or pull the lever toward you to switch the high beams off.

Headlamp Flasher

E142450

Pull the lever toward you slightly and release it to flash the headlamps.

AUTOLAMPS (IF EQUIPPED)

Note: It may be necessary to switch your

headlamps on manually in severe weather conditions.

E142451

The headlamps will switch on and off automatically in low light situations or during inclement weather.

The headlamps will remain on for a period of time after you switch the ignition off. You can adjust the time delay using the information display controls. See Information Displays (page 82).

Lighting

Note: If you switch autolamps on in

conjunction with autowipers, low beam headlamps will illuminate automatically when the rain sensor activates the windshield wipers continuously.

INSTRUMENT LIGHTING DIMMER

Note: If you disconnect the battery or it

becomes discharged, the illuminated components will switch to the maximum setting.

Vehicles With Front Fog Lamps

E132712

Press repeatedly or press and hold until the desired level is reached.

Vehicles Without Front Fog Lamps

A B

E142452

Press repeatedly or press and hold to dim.

Press repeatedly or press and hold to brighten.

HEADLAMP EXIT DELAY

After you switch the ignition off, you can switch the headlamps on by pulling the direction indicator lever toward you. You will hear a short tone. The headlamps will switch off automatically after three minutes with any door open or 30 seconds after the last door has been closed. You can cancel this feature by pulling the direction indicator toward you again or switching the ignition on.

DAYTIME RUNNING LAMPS (IF

EQUIPPED)

WARNING

Always remember to switch your headlamps on in low light situations

or during inclement weather. The system does not activate the tail lamps and may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.

Lighting

The system switches the low beam headlamps on at a reduced intensity in daylight conditions.

To switch the system on, switch the ignition on, and switch the lighting control to the off, autolamp or parking lamp position.

AUTOMATIC HIGH BEAM CONTROL (IF EQUIPPED)

The system will automatically turn on your high beams if it is dark enough and no other traffic is present. When it detects an approaching vehicle’s headlights, a preceding vehicle’s tail lamps or street lighting, the system will turn off the high beams before they distract other drivers. The low beams remain on.

Note: If it appears that automatic control of the high beams is not functioning properly, check the windshield in front of the camera for blockage. A clear view of the road is required for proper system operation. Any windshield damage in the area of the camera field-of-view should be repaired.

Note: If a blockage is detected (e.g. bird dropping, bug splatter, snow, or ice) and no changes are observed, the system will go into low beam mode until the blockage is cleared. A message may also appear in the instrument cluster display noting the front camera is blocked.

Note: Typical road dust, dirt and water spots will not affect the automatic high beam system’s performance. However, in cold or inclement weather conditions, the automatic high beam system's availability may be decreased. If you want to change the beam state independently of the system, you may turn the high beams ON or OFF using the multifunction switch lever. Automatic control will resume when conditions are correct.

Note: Modification of the vehicle ride height (e.g. using much larger tires) may degrade feature performance.

A camera sensor is centrally mounted behind the windshield of the vehicle, and monitors conditions continuously to decide when to switch the high beams off and on.

Once the system is active, the high beams will switch on if:

• The ambient light level is low enough that high beams are needed.

• There is no traffic in front of the vehicle.

• The vehicle speed is greater than

25 mph (40 km/h).

The high beams will switch off if:

• An approaching vehicle's headlights or a preceding vehicle's tail lamps are detected.

• Vehicle speed falls below 16 mph (25 km/h).

• The ambient light level is high enough that high beams are not required.

• Severe rain, snow, or fog is detected.

• The camera is blocked.

Activating the System

Switch on the system using the information display and autolamps. See Information Displays (page 82). See Autolamps (page 66).

E142451

Lighting

Turn the lighting control to the autolamps position.

Manually Overriding the System

E130140

Use the lever to switch between the high beams and the low beams.

Note: This is a temporary override and the system will return to automatic operation after a short period.

To permanently deactivate the system, use the information display menu or turn the lighting control switch from autolamps to headlamps.

FRONT FOG LAMPS (IF EQUIPPED)

E142453

Press the control to switch the fog lamps on or off.

You can switch the fog lamps on when the lighting control is in any position except off and the high beams are not on.

DIRECTION INDICATORS

E145595

Push the lever up or down to use the direction indicators.

Note: Tap the lever up or down to make the direction indicators flash three times to indicate a lane change.

INTERIOR LAMPS

The lamps will switch on when one of the following conditions have been met:

• You open any door.

• You press a remote control button.

• You touch switch A on the front interior

lamp.

Front Interior Lamp

Note: The front interior lamp switches are

on the overhead console. The exact location of each switch on the overhead console depends upon which roof, sunroof, and window shade features are equipped on the vehicle.

Lighting

Note: Touch switch C to switch the door

function off when you open any door. The indicator lamp will illuminate amber when the door function is off. When the door function is off and you open a door, the courtesy and door lamps will stay off. Touch switch C again to switch the door function back on. The indicator lamp will illuminate blue when the door function is on. When the door function is on and you open a door, the courtesy and door lamps will switch on.

A B

E146410

All lamps on switchA All lamps off switchB Door function switchC

You can switch individual map lamps on independently by touching a map lens.

Rear Interior Lamp (If Equipped)

E142455

You can switch individual dome lamps on independently by pressing switch A.

Lighting

POWER WINDOWS

WARNINGS

Do not leave children unattended in your vehicle and do not let them play with the power windows. They may

seriously injure themselves.

When closing the power windows, you should verify they are free of

obstructions and make sure that children and pets are not in the proximity of the window openings.

E146043

Note: You may hear a rumbling noise when just one of the windows are open. Lower the opposite window slightly to reduce this noise.

Press the switch to open the window. Lift the switch to close the window.

One-Touch Down

Press the switch fully and release it. Press again or lift it to stop the window.

One-Touch Up

Lift the switch fully and release it. Press or lift it again to stop the window.

Bounce-Back

The window will stop automatically while closing. It will reverse some distance if there is an obstacle in the way.

Overriding the Bounce-Back Feature

WARNING

When you override the bounce-back feature the window will not reverse

if it detects an obstacle. Take care when closing the windows to avoid personal injury.

Pull up the window switch and hold within two seconds of the window reaching the bounce-back position. The window will travel up with no bounce-back protection. The window will stop if you release the switch before the window is fully closed.

Window Lock

E144072

Press the control to lock or unlock the rear window controls. It will illuminate when you lock the rear window controls.

Accessory Delay

You can use the window switches for several minutes after you switch the ignition off or until you open either front door.

Windows and Mirrors

GLOBAL OPENING AND CLOSING

You can use the remote control to operate the windows with the ignition off.

Note: You can enable or disable this feature in the information display or see an authorized dealer. See General Information (page 82).

Note: To operate this feature, accessory delay must not be active.

Opening the Windows

You can only open the windows for a short time after you unlock your vehicle with the remote control. After you unlock your vehicle, press and hold the remote control unlock button to open the windows and vent the moonroof. Release the button once movement starts. Press the lock or unlock button to stop movement.

Closing the Windows

WARNING

When closing the windows and moonroof, you should verify they are

free of obstructions and make sure that children and pets are not in the proximity of the window openings.

To close the windows and moonroof, press and hold the remote control lock button. Release the button once movement starts. Press the lock or unlock button to stop movement.

EXTERIOR MIRRORS

Power Exterior Mirrors

WARNING

Do not adjust the mirrors when your

vehicle is moving.

E144073

Left-hand mirrorA Adjustment controlB Right-hand mirrorC

To adjust a mirror:

1. Select the mirror you want to adjust. The control will illuminate.

2. Adjust the position of the mirror.

3. Press the mirror switch again.

Fold-Away Exterior Mirrors

Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position.

Heated Exterior Mirrors (If Equipped)

See Heated Windows and Mirrors (page

126).

Memory Mirrors (If Equipped)

You can save and recall the mirror positions through the memory function. See Memory Function (page 132).

Auto-Dimming Feature (If Equipped)

The driver’s exterior mirror will automatically dim when the interior auto-dimming mirror is activated.

Windows and Mirrors

Signal Indicator Mirrors (If Equipped)

The outer portion of the appropriate mirror housing will blink when the turn signal is activated.

Integrated Blind Spot Mirrors (If

Equipped)

WARNING

Objects in the blind spot mirror are closer than they appear.

Blind spot mirrors have an integrated convex mirror built into the upper outboard corner of the exterior mirrors. They are designed to increase your visibility along the side of your vehicle.

Check the main mirror first before a lane change, then check the blind spot mirror. If no vehicles are present in the blind spot mirror and the traffic in the adjacent lane is at a safe distance, signal that you intend to change lanes. Glance over your shoulder to verify traffic is clear and carefully change lanes.

E138665

The image of the approaching vehicle is small and near the inboard edge of the main mirror when it is at a distance. The image becomes larger and begins to move outboard across the main mirror as the vehicle approaches (A). The image will transition from the main mirror and begin to appear in the blind spot mirror as the vehicle approaches (B). The vehicle will transition to your peripheral field of view as it leaves the blind spot mirror (C).

Blind Spot Monitor (If Equipped)

See Blind Spot Monitor (page 198).

INTERIOR MIRROR

WARNING

Do not adjust the mirror when your vehicle is moving.

Windows and Mirrors

Note: Do not clean the housing or glass of

any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products.

You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side.

Pull the tab below the mirror toward you to reduce glare at night.

Auto-Dimming Mirror (If Equipped)

Note: Do not block the sensors on the front

and back of the mirror. Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor.

The mirror will dim automatically to reduce glare when bright lights are detected from behind your vehicle. It will automatically return to normal reflection when you select reverse gear to make sure you have a clear view when backing up.

SUN VISORS

E138666

Rotate the sun visor toward the side window and extend it rearward for extra shade.

Illuminated Vanity Mirror

E138667

Lift the cover to switch the lamp on.

MOONROOF (IF EQUIPPED)

WARNINGS

Do not let children play with the moonroof or leave them unattended in the vehicle. They may seriously

hurt themselves.

When closing the moonroof, you should verify that it is free of

obstructions and make sure that children and pets are not in the proximity of the roof opening.

The sliding shade can be manually opened or closed when the moonroof is closed. Pull the shade toward the front of the vehicle to close it.

The moonroof controls are located on the overhead console and have a one-touch open and close feature. To stop it during one-touch operation, touch the control a second time.

Windows and Mirrors

E144499

OpenA VentB CloseC

Opening and Closing the Moonroof

Touch (A) to open the moonroof. It will stop short of the fully opened position.

Note: This position helps to reduce wind noise or rumbling which may happen with the moonroof fully open. Touch (A) again to fully open the moonroof.

Touch (C) to close the moonroof.

Bounce-Back

The moonroof will stop automatically and reverse some distance if an obstacle is detected while closing.

Touch and hold (C) within two seconds of a bounce-back event to override this function.

Venting the Moonroof

Touch (B) to vent the moonroof. Touch (C) to close it.

Windows and Mirrors

GAUGES

Type 1 and 2

E144485

TachometerA Information Display (Type 2 shown Type 1 similar)B SpeedometerC Fuel GaugeD Engine Coolant Temperature GaugeE

Information Display

Odometer

Located in the bottom of the information display Registers the accumulated distance your vehicle has traveled.

Outside Air Temperature

Shows the outside air temperature.

Compass

Displays the vehicle’s heading direction.

Trip Computer

See General Information (page 82).

Instrument Cluster

Vehicle Settings and Personalization

See General Information (page 82).

Engine Coolant Temperature Gauge

Shows the temperature of the engine coolant. At normal operating temperature, the needle will remain in the center section. If the needle enters the red section, the engine is overheating. Stop the engine, switch the ignition off and determine the cause once the engine has cooled down.

Note: Do not restart the engine until the cause of overheating has been resolved.

WARNING

Never remove the coolant reservoir cap while the engine is running or hot.

Fuel Gauge

Switch the ignition on. The fuel gauge will indicate approximately how much fuel is left in the fuel tank. The fuel gauge may vary slightly when your vehicle is moving or on a gradient. The arrow adjacent to the fuel pump symbol indicates on which side of the vehicle the fuel filler door is located.

Type 3

E144486

Instrument Cluster

Left Information DisplayA SpeedometerB Right Information Display See General Information (page 341).C

Left Information Display

Odometer

Located in the bottom of the information display Registers the accumulated distance your vehicle has traveled.

Trip Computer

See General Information (page 82).

Vehicle Settings and Personalization

See General Information (page 82).

WARNING LAMPS AND INDICATORS

The following warning lamps and indicators will alert you to a vehicle condition that may become serious. Some lamps will illuminate when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information.

Note: Some warning indicators appear in the information display and function the same as a warning lamp but do not display when you start your vehicle.

Adaptive Cruise Control (If Equipped)

E144524

The speed control system indicator light changes color to indicate what mode the system

is in: See Using Cruise Control (page 185). On (white light): Illuminates when the

adaptive cruise control system is turned on. Turns off when the speed control system is turned off.

Engaged (green light): Illuminates when the adaptive cruise control system is engaged. Turns off when the speed control system is disengaged.

Anti-Lock Braking System

If it illuminates when you are driving, this indicates a

malfunction. You will continue to have the normal braking system (without ABS) unless the brake system warning lamp is also illuminated. Have the system checked by your authorized dealer.

Auto Start-stop (If Equipped)

It will illuminate to inform you

when the engine shuts down or

in conjunction with a message.

Battery

If it illuminates while driving, it

indicates a malfunction. Switch

off all unnecessary electrical equipment and have the system checked by your authorized dealer immediately.

Blind Spot Monitor (If Equipped)

E151262

It will illuminate when you switch this feature off or in conjunction with a message. See Blind Spot

Monitor (page 198). See Information Messages (page 90).

Brake System

E144522

It will illuminate when you

engage the parking brake with

the ignition on.

Instrument Cluster

If it illuminates when you are driving, check that the parking brake is not engaged. If the parking brake is not engaged, this indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by your authorized dealer.

WARNING

Driving your vehicle with the warning lamp on is dangerous. A significant

decrease in braking performance may occur. It will take you longer to stop your vehicle. Have your vehicle checked by your authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury.

Cruise Control (If Equipped)

E71340

It will illuminate when you switch this feature on.

Direction Indicator

Illuminates when the left or right turn signal or the hazard warning

flasher is turned on. If the indicators stay on or flash faster, check for a burned out bulb. See Changing a Bulb (page 254).

Door Ajar

Displays when the ignition is on

and any door is not completely

closed.

Electric Park Brake

E146190

It will illuminate or flash when

the electric parking brake has a

malfunction.

Engine Coolant Temperature

Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as

possible, switch off the engine and let cool.

Engine Oil

If it illuminates with the engine running or when you are driving,

this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine Oil Check (page 244).

Note: Do not resume your journey if it illuminates despite the level being correct. Have the system checked by your authorized dealer immediately.

Fasten Safety Belt

It will illuminate and a chime will

sound to remind you to fasten

your safety belt. See Safety

Belt Minder (page 29).

Front Airbag

If it fails to illuminate when you

start your vehicle, continues to

flash or remains on, it indicates a malfunction. Have the system checked by your authorized dealer.

Front Fog Lamps (If Equipped)

It will illuminate when you switch

the front fog lamps on.

Instrument Cluster

Heads Up Display (If Equipped)

E156133

A red beam of lights will illuminate on the windshield in

certain instances when using adaptive cruise control and/or the collision warning system. It will also illuminate momentarily when you start your vehicle to make sure the display works.

High Beam

It will illuminate when you switch

the high beam headlamps on. It

will flash when you use the headlamp flasher.

Hood Ajar

E159324

Displays when the ignition is on

and the hood is not completely

closed.

Lane Keeping Aid (If Equipped)

E144813

Illuminates when the lane

keeping system is activated.

Low Fuel Level

It will illuminate when the fuel

level is low or the fuel tank is

nearly empty. Refuel as soon as possible.

Low Tire Pressure Warning

It will illuminate when your tire

pressure is low. If the lamp

remains on with the engine

running or when driving, check your tire pressure as soon as possible.

It will also illuminate momentarily when you switch the ignition on to confirm the lamp is functional. If it does not illuminate when you switch the ignition on, or begins to flash at any time, have the system checked by your authorized dealer.

Parking Lamps

It will illuminate when you switch the parking lamps on.

Powertrain Fault

Illuminates when a powertrain or an AWD fault has been detected. Contact your

authorized dealer as soon as possible.

Service Engine Soon

If the service engine soon indicator light stays illuminated

after the engine is started, it indicates that the On Board Diagnostics system (OBD) has detected a malfunction of the vehicle emissions control system. Refer to On board diagnostics (OBD) in the Fuel and Refueling chapter for more information about having your vehicle serviced. See Emission Control System (page 155).

If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately.

Note: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter or other vehicle components.

Instrument Cluster

The service engine soon indicator light illuminates when the ignition is first turned on prior to engine start to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing.

Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for I/M testing. See Emission Control

System (page 155).

Stability Control

E138639

It will flash when the system is active. If it remains illuminated

or does not illuminate when you switch the ignition on, this indicates a malfunction. During a malfunction the system will switch off. Have the system checked by your authorized dealer immediately. See Using Stability

Control (page 175).

Stability Control Off

It will illuminate when you switch

the system off. It will go out

when you switch the system back on or when you switch the ignition off. See Using Stability Control (page

175).

Trunk Ajar

Displays when the ignition is on

and the trunk is not completely

closed.

AUDIBLE WARNINGS AND INDICATORS

Key in Ignition Warning Chime

Sounds when you open the driver's door and you have left the key in the ignition with it in the off or accessory position.

Keyless Warning Alert (If Equipped)

Chirps the horn twice when you exit the vehicle and the keyless vehicle is in RUN, indicating the vehicle is still on.

Headlamps On Warning Chime

Sounds when you remove the key from the ignition and open the driver's door and you have left the headlamps or parking lamps on.

Parking Brake On Warning Chime

Sounds when you have left the parking brake on and drive your vehicle. If the warning chime remains on after you have released the parking brake, have the system checked by your authorized dealer immediately.

Instrument Cluster

GENERAL INFORMATION

WARNING

Driving while distracted can result in loss of vehicle control, accident and

injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle. We recommend against the use of any handheld device while driving and that you comply with all applicable laws.

Note: Your vehicle may or may not be equipped with all the messages listed in this chapter. Your vehicle will not display messages of systems it is not equipped with.

Various systems on your vehicle can be controlled using the information display controls on the steering wheel. Corresponding information is displayed in the information display.

Information Display Controls (Type 1 and Type 2)

E144637

• Press the up and down arrow buttons to scroll through and highlight the options within a menu.

• Press the right arrow button to enter a sub-menu.

• Press the left arrow button to exit a menu.

• Press and hold the left arrow button at any time to return to the main menu display (escape button).

• Press the OK button to choose and confirm settings or messages.

You can access the menu using the information display control.

Note: Some options may appear slightly different or not at all if the items are optional.

Trip 1 and 2

Trip Odometer

Trip Timer

Fuel Used

Average Fuel

Information Displays

Trip 1 and 2

All Values

Outside Temperature

• Resetting the Trip Computer — Press and hold OK on the current screen to reset the respective trip, distance, time and fuel information.

• Trip Odometer — Registers the distance of individual journeys.

• Trip Timer — timer stops when the vehicle is turned off and restarts when the vehicle

is restarted.

• Fuel Used — shows the amount of fuel used for a given trip.

• Average Fuel — shows the average fuel economy for a given trip.

• All Values — Shows all trip values.

• Outside Temperature — Shows the outside air temperature.

Fuel Economy

Distance to E

Inst Fuel Econ

Long Term Average Fuel

Fuel History

All Values

Information

Available Auto Start-Stop messaging will provide details about what is happening with your system. See Informa- tion Messages (page 90).

Auto Stop/Start

-Intelligent AWD

-MyKey

All active warnings will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Use the up/ down arrow buttons to scroll through the list.

System Check

Information Displays

Settings

On or OffTraction CtrlDriver Assist

On (default on key cycle) or OffBlind Spot

On or OffRear Park Aid

On or OffHill Start

Assist

On or OffCross Traffic

Auto Engine OffVehicle

5, 10 or 30 minutesFuel History

Auto HighbeamLighting

Off or XX SecondsAutolamp Delay

Settings (cont’d)

AutolockLocksVehicle

(cont’d)

Autounlock

Relock

Mislock

All Doors / Driver First

Remote Unlock

Set to XXX %Oil Life Rest

Switch Inhibit

Remote Open / Remote CloseWindows

Courtesy Wipe / Rain SensingWipers

Hold OK to Create MyKeyCreate MyKeyMyKey

Always On / User Selectable911 Assist

Always On / User SelectableTraction

Control

Choose desired speed or OffMax Speed

Information Displays

Settings (cont’d)

Choose desired speed or OffSpeed Minder

On or OffVolume

Limiter

On or OffDo Not

Disturb

Hold OK to Clear All MyKeysClear MyKeys

Choose your applicable settingLanguageDisplay

Choose your applicable setting

DistanceUnits

Choose your applicable setting

Temperature

Information Display Controls (Type 3)

E144638

• Press the up and down arrow buttons to scroll through and highlight the options within a menu.

• Press the right arrow button to enter a sub-menu.

• Press the left arrow button to exit a menu.

• Press and hold the left arrow button at any time to return to the main menu display (escape button).

• Press the OK button to choose and confirm settings or messages.

Main menu

From the main menu bar on the left side of the information display, you can choose from the following categories:

E144639

Display Mode

E138660

Trip 1 & 2

E144640

Fuel Economy

E144642

Information

E100023

Settings

Scroll up/down to highlight one of the categories, then press the right arrow key or OK to enter into that category. Press the left arrow key as needed to exit back to the main menu.

Information Displays

Display Mode

E144639

Use the up/down arrow buttons to choose between the following display options.

Option 6Option 5Option 4Option 3Option 2Option 1Display mode

----XXXXX mi (km) to

empty

XXXXXXFuel gauge

--XX--Round tachometer

X---X-Vertical tacho-

meter

--X---Engine coolant

temp gauge

XX----AWD gauge

• XXX mi (km) to empty: Shows the approximate distance the vehicle will travel.

• Fuel gauge: Indicates approximately how much fuel is left in the fuel tank. The fuel

gauge may vary slightly when the vehicle is in motion or on a grade. When the fuel level becomes low, the level indicator will change to amber. When the fuel level becomes critically low, the level indicator will change to red. Note: When a MyKey® is in use, low fuel warnings will display earlier. The fuel icon and arrow indicates which side of the vehicle the fuel filler door is located.

• Round tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. During SelectShift Automatic™ transmission (SST) use, the currently selected gear will appear in the display.

• Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the level indicator will be in the normal range. If the engine coolant temperature exceeds the normal range, stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.

• Intelligent AWD (if equipped): displays power distribution between the front and rear wheels. More power to either front or rear wheels will be displayed by more area filled in.

Trip 1 & 2

E138660

Choose between the standard or enhanced trip display.

Information Displays

Enhanced displayStandard displayTrip 1 & 2

XXTrip Odometer

XXTrip Timer

X-Average Fuel

X-Fuel Used

-Press and hold OK to reset the currently

displayed trip information.

• Trip Odometer — shows the accumulated trip distance.

• Trip Timer— timer stops when the vehicle is turned off and restarts when the vehicle

is restarted.

• Average Fuel — shows the average fuel economy for a given trip.

• Fuel Used — shows the amount of fuel used for a given trip.

Fuel Economy

E144640

Use the left/right arrow buttons to choose the desired fuel economy display.

Option 2Option 1Fuel Economy

XXDTE

-XInst Fuel Econ

XXAverage Fuel

X-Fuel History

5, 10, or 30 minuteFuel History Duration

• DTE: Distance To Empty shows the approximate distance the vehicle will travel on the fuel remaining in the tank. Changes in driving pattern may cause the value to vary.

• Inst Fuel Econ: This display shows a visual graph of your instantaneous fuel economy.

• Average Fuel: Indicates the average fuel consumption since the function was last

reset.

• Fuel History: shows a bar chart of your fuel history.

• Fuel History Duration: shows fuel usage over a 5, 10, or 30 minute time span.

Information Displays

Info

E144642

In this mode, you can view different vehicle system information and perform a

system check.

Information

Available Auto Start-Stop messaging will provide details about what is happening with your system. See Informa- tion Messages (page 90).

Auto Stop/Start

-Driver Alert

-MyKey

System Check

Settings

E100023

In this mode, you can configure different driver setting choices.

Note: Some items are optional and may not appear.

Settings

On / OffTraction CtrlDriver

Assist

On (default on key cycle) / OffBlindspot

High / Normal / LowSensitivityCollision Warning

On / OffDistance Alert

On (default on key cycle) / Off

Warn

Adaptive (default on key cycle) or NormalCruise Control

On (default on key cycle) / OffCross Traffic

On (default on key cycle) / OffDriver Alert

On / OffHill start

Information Displays

Settings (cont’d)

Alert / Aid / BothModeLane Keeping SystemDriver Assist (cont’d)

High / Normal / LowIntensity

On (default on key cycle) / OffFront Park Aid

On (default on key cycle) / OffRear Park Aid

On (default on key cycle) / OffAuto Engine OffVehicle

On / OffEasy Entry/Exit

Auto HighbeamLighting

Off or XX SecondsAutolamp Delay

On / OffAutolockLocks

On / OffAutounlock

On / OffMislock

All doors / Driver’s doorRemote Unlocking

Set to XXX %Oil Life Reset

Settings (cont’d)

Heater – A/C: Auto /

Last Settings

Climate Control (using this feature allows you to select different climate control modes when the vehicle is started using the remote start feature)

Remote StartVehicle

(cont’d)

Front Defrost: Auto / Off

Rear Defrost: Auto / Off

Driver Seat: Auto / Off

Passenger Seat: Auto /

Off

5 / 10 /15 minutesDuration

On / OffQuiet Start

Enable / DisableSystem

Information Displays

Settings (cont’d)

On / OffSwitch InhibitVehicle

(cont’d)

On / OffRemote OpenWindows

On / OffRemote Close

On / OffCourtesy WipeWipers

On / OffRain Sensing

Hold OK to Create MyKeyCreate MyKeyMyKey

Always On / User Selectable911 Assist

Always On / User SelectableTraction Control

Choose desired speed or offMax Speed

Choose desired speed or offSpeed Minder

On / OffVolume Limiter

Always On / User SelectableDo Not Disturb

Hold OK to Clear All MyKeysClear MyKeys

Choose your applicable settingLanguageDisplay

Choose your applicable setting

DistanceUnits

Choose your applicable setting

Temperature

Fuel Gauge / Fuel + TachGauge Display

INFORMATION MESSAGES

Note: Depending on the vehicle options

equipped with your vehicle, not all of the messages will display or be available. Certain messages may be abbreviated or shortened depending upon which cluster type you have.

E144636

Information Displays

Press the OK button to acknowledge and remove some messages from the information display. Other messages will be removed automatically after a short

time. Certain messages need to be confirmed

before you can access the menus.

Active Park

ActionMessage

Displayed when the system needs service. Contact your

authorized dealer as soon as possible.

Active Park Fault

Adaptive Cruise Control

ActionMessage

Displayed when a radar malfunction is preventing the ACC

from engaging. See Using Adaptive Cruise Control (page

186).

Adaptive Cruise

Malfunction

Displayed when conditions exist such that the adaptive cruise

cannot function properly. See Using Adaptive Cruise

Control (page 186).

Adaptive Cruise Not

Available

Displayed when the radar is blocked because of poor radar

visibility due to bad weather or ice/mud/water in front of

radar. Driver can typically clean the sensor to resolve. See

Using Adaptive Cruise Control (page 186).

Adaptive Cruise Not

Available Sensor

Blocked See Manual

Displayed when the automatic braking has been disabled.Cruise Control Auto-

matic Braking Turned

Off

Displayed when a radar malfunction is preventing the ACC

from engaging.

Front Sensor Not Aligned

Displayed when the adaptive cruise has reinstated controls

to the driver.

Adaptive Cruise - Driver

Resume Control

Displays when the vehicle speed is too slow to activate the

adaptive cruise.

Adaptive Cruise Speed

Too Low to Activate

Displays when the adaptive cruise is automatically adjusting

the gap distance and the driver needs to shift the transmission

into a lower gear.

Adaptive Cruise Shift

Down

Information Displays

AdvanceTrac®

ActionMessage

Displays when the system detects a malfunction due to a

blocked sensor.

Service AdvanceTrac

Displayed when the traction control has been disabled or

enabled by the driver.

AdvanceTrac Off On

Airbag

ActionMessage

Displays when the system detects a malfunction due to a

blocked sensor.

Occupant Sensor

BLOCKED Remove

Objects Near Passenger

Seat

Alarm

ActionMessage

Displays when the alarm has been triggered due to unauthor-

ized entry. See Anti-Theft Alarm (page 60).

Vehicle Alarm to Stop

Alarm, Start Vehicle

Auto Start-Stop

ActionMessage

The engine needs to be restarted, press the brake pedal to

start.

Auto StartStop Press Brake to Start Engine

The engine needs to be restarted, press the brake pedal harder

to start.

Auto StartStop Press

Brake Harder to Activate

The engine needs to be restarted, press the clutch pedal to

start.

Auto StartStop Press

Clutch to Start Engine

The engine needs to be restarted, press any pedal to start.Auto StartStop Press

Any Pedal

Select neutral for the system to restart the engine.Auto StartStop Select

Neutral To Start Engine

Information Displays

ActionMessage

Select park for the system to restart the engine.Auto StartStop Shift to

P Restart Engine

The system is not functioning. A manual restart is required.Auto StartStop Manual

Restart Required

Displays when conditions are not met for the Auto StartStop

system to function properly See Start-Stop (page 149).

Auto StartStop Not

Available

StartStop has shutoff the engine automatically.Engine Stopped

The wheels are at a sharp angle or the steering wheel is being

turned.

Engine On due to Vehicle

Maneuvering

The wheels are at a sharp angle or the steering wheel is being

turned.

Engine On due to

Steering Wheel Maneuv-

ering

Engine may be On to support high demand for electrical

accessories, such as operating power windows, rear defroster,

or when using the Power point.

Engine On due to Accessory Usage

Engine On to support normal vehicle operation. Includes

external vehicle conditions, such as altitude, traffic, low

ambient temperature. Also includes battery outside optimal

operating conditions (state of charge and temperature), and

inadequate brake vacuum (can occur if the brake pedal is

depressed a number of times in succession).

Engine On Normal Oper-

ation

Engine On to achieve or maintain interior compartment at an

acceptable level.

Heating or Cooling

Engine On required to support use of Power Outlet (110V).Power Outlet in Use

Automatic Engine Shutdown

ActionMessage

Displays when the engine is getting ready to shut off.Engine Shuts Off in XX

Seconds

Displays when the engine has shut off to help increase fuel

economy.

Engine Shut Off for Fuel

Economy

Displays when the engine is getting ready to shut off. You can press OK on the left steering wheel button to override the shut

down.

Engine Shuts Off in XX

Seconds Press Ok to

Override

Information Displays

AWD

ActionMessage

Displayed when the AWD system has been temporarily

disabled to protect itself from overheating.

AWD Temporarily

Disabled

Displayed when the AWD system has been automatically

disabled to protect itself. This is caused by operating the

vehicle with the compact spare tire installed or if the system

is overheating.

AWD Off

The AWD system will resume normal function and clear this

message after driving a short distance with the road tire re-

installed or after the system is allowed to cool.

AWD Restored

Displayed in conjunction with the Throttle Control/Transmission/AWD light when the AWD system is not operating properly. If the warning stays on or continues to come on, contact

your authorized dealer as soon as possible.

AWD Malfunction

Service Required

Battery and Charging System

ActionMessage

Displayed when the charging system needs servicing. If the

warning stays on or continues to come on, contact your

authorized dealer as soon as possible.

Check Charging System

Displayed when the battery management system detects an extended low-voltage condition. Various vehicle features will

be disabled to help preserve the battery. Turn off as many of

the electrical loads as soon as possible to improve system

voltage. If the system voltage has recovered, the disabled

features will operate again as normal

Low Battery Features

Temporarily Turned Off

Displayed when the battery management system determines

that the battery is at a low state of charge. Turn the ignition

off as soon as possible to protect the battery. This message

will clear once the vehicle has been started and the battery

state of charge has recovered. Turning off unnecessary elec-

trical loads will allow faster battery state-of-charge recovery.

Turn Power Off to Save

Battery

Information Displays

Blind Spot Information and Cross Traffic Alert System

ActionMessage

Displayed when a fault with the system has occurred. Contact

your authorized dealer as soon as possible.

Blindspot System Fault

Displayed when the system sensors are blocked. Contact your

authorized dealer as soon as possible. See Blind Spot

Monitor (page 198).

Blindspot Not Available

Sensor Blocked See

Manual

Displayed when the system detects a vehicle. See Blind Spot

Monitor (page 198).

Cross Traffic Vehicle

Coming From X

Displayed when the blind spot information system and cross

traffic alert system sensors are blocked. See Blind Spot

Monitor (page 198).

Cross Traffic Not Avail-

able Sensor Blocked See

Manual

Displays when a fault with the system has occurred. Contact

your authorized dealer as soon as possible.

Cross Traffic System

Fault

Collision Warning System

ActionMessage

Displayed when there is a system malfunction with the colli-

sion warning system. The system will be disabled. Contact

your authorized dealer as soon as possible.

Collision Warning

Malfunction

Displayed when the collision warning system radar is blocked

because of poor radar visibility due to bad weather or ice/

mud/water in front of the radar. Driver can typically clean the

sensor to resolve. Contact your authorized dealer as soon as

possible.

Collision Warning Not

Available Sensor

Blocked See Manual

Displayed when there is a system malfunction with the colli-

sion warning system. The system will be disabled. Contact

your authorized dealer as soon as possible.

Collision Warning Not

Available

Information Displays

Doors and Locks

ActionMessage

Displays when the door(s) listed is not completely closed and

the vehicle is moving.

X Door Ajar

Displays when the door(s) listed is not completely closed.

Displays when the luggage compartment is not completely

closed.

Trunk ajar

Displays when the door switches have been disabled.Switches Inhibited

Security Mode

Displayed when there is a system malfunction with the child

locks. Contact your authorized dealer as soon as possible.

Child Lock Malfunction

Service Required

Displays the factory keypad code after the keypad has been

reset.

Factory Keypad Code

XXXXX

Driver Alert

ActionMessage

Stop and rest as soon as it is safe to do so.Driver Alert Warning Rest

Now

Take a rest break soon.Driver Alert Warning Rest

Suggested

Engine

ActionMessage

Engine service is required. Contact your authorized dealer.Engine Fault Service

Now

Displays when the engine temperature is too high. Stop the

vehicle in a safe place and allow to engine to cool. If the

problem persists, contact your authorized dealer. See Engine

Coolant Check (page 245).

High Engine Temper-

ature Stop Safely

Information Displays

Fuel

ActionMessage

Displayed as an early reminder of a low fuel condition.Fuel Level Low

Displayed when the fuel fill inlet may not be properly closed.Check Fuel Fill Inlet

Hill Start Assist

ActionMessage

Displays when hill start assist is not available. Contact your

authorized dealer. See Hill Start Assist (page 162).

Hill Start Assist Not

Available

Keys and Intelligent Access

ActionMessage

Displayed as a reminder to press the brake while starting the

vehicle.

Press Brake to START

Displayed if the key is not detected by the system. See

Keyless Starting (page 143).

No Key Detected

Displayed when the start/stop button is pressed to shut off

the engine and a Intelligent Access Key is not detected inside

the vehicle.

Restart Now or Key is

Needed

Displayed when the vehicle is in the run ignition state.Run Power Active

This message is displayed when there is a problem with your

vehicle’s starting system. See your authorized dealer for

service.

Starting System Fault

Displayed as a reminder to press the brake and clutch while

starting the vehicle.

Press Brake and Clutch

to Start

Displayed as a reminder to press the clutch in while starting

the vehicle.

Press Clutch to Start

Displays when the starter has exceeded its cranking time in

attempting to start the vehicle.

Cranking Time Exceeded

Displayed during spare key programming, when an intelligent

access key is programmed to the system.

Key Program Successful

Information Displays

ActionMessage

Displayed during spare key programming, when an intelligent

access key has failed to be programmed.

Key Program Failure

Displayed during spare key programming when the maximum

number of keys have been programmed.

Max Number of Keys

Learned

Displayed during spare key programming when not enough

keys have been programmed.

Not Enough Keys

Learned

Displays when the key battery is low. Change the battery as

soon as possible.

Key Battery Low Replace

Soon

Displayed when an attempt is made to program a spare key

using two existing keys.

Could Not Program

Integrated Key

Displays to inform the driver that they are exiting the vehicle

and the engine is on.

Engine On

Lane Keeping System

ActionMessage

The system has malfunctioned. Contact your authorized

dealer as soon as possible.

Lane Keeping Sys.

Malfunction Service

Required

The system has detected a condition that has caused the

system to be temporarily unavailable.

Front Camera Tempor-

arily Not Available

The system has detected a condition the requires the wind-

shield to be cleaned to operate properly.

Front Camera Low Visib-

ility Clean Screen

The system has malfunctioned. Contact your authorized

dealer as soon as possible.

Front Camera Malfunc-

tion Service Required

Displayed when the system requests the driver to keep their

hands on the steering wheel.

Keep Hands on Steering

Wheel

Information Displays

FORD Fusion 2013 User Manual v.2

Specifications and Main Features

Frequently Asked Questions

User Manual

ABOUT THIS MANUAL

SYMBOLS GLOSSARY

Introduction

DATA RECORDING

CALIFORNIA PROPOSITION 65

PERCHLORATE

FORD CREDIT

REPLACEMENT PARTS RECOMMENDATION

SPECIAL NOTICES

MOBILE COMMUNICATIONS EQUIPMENT

EXPORT UNIQUE OPTIONS

GENERAL INFORMATION

Child Safety

CHILD SEAT POSITIONING

BOOSTER SEATS

INSTALLING CHILD SEATS

CHILD SAFETY LOCKS

PRINCIPLE OF OPERATION

Safety Belts

FASTENING THE SAFETY BELTS

SAFETY BELT HEIGHT ADJUSTMENT

SAFETY BELT WARNING LAMP AND INDICATOR CHIME

SAFETY BELT MINDER

CHILD RESTRAINT AND SAFETY BELT MAINTENANCE

Personal Safety System™

PRINCIPLE OF OPERATION

Supplementary Restraints System

DRIVER AND PASSENGER AIRBAGS

KNEE AIRBAG

FRONT PASSENGER SENSING SYSTEM

SIDE AIRBAGS

SIDE CURTAIN AIRBAGS

CRASH SENSORS AND AIRBAG INDICATOR

AIRBAG DISPOSAL

GENERAL INFORMATION ON RADIO FREQUENCIES

REMOTE CONTROL

Keys and Remote Controls

REPLACING A LOST KEY OR REMOTE CONTROL

PRINCIPLE OF OPERATION

CREATING A MYKEY

CLEARING ALL MYKEYS

CHECKING MYKEY SYSTEM STATUS

USING MYKEY WITH REMOTE START SYSTEMS

MYKEY TROUBLESHOOTING

LOCKING AND UNLOCKING

Locks

KEYLESS ENTRY (IF EQUIPPED)

INTERIOR LUGGAGE COMPARTMENT RELEASE

PASSIVE ANTI-THEFT SYSTEM

Security

ANTI-THEFT ALARM

ADJUSTING THE STEERING WHEEL

AUDIO CONTROL (IF EQUIPPED)

Steering Wheel

VOICE CONTROL (IF EQUIPPED)

CRUISE CONTROL

INFORMATION DISPLAY CONTROL

WINDSHIELD WIPERS

AUTOWIPERS (IF EQUIPPED)

Wipers and Washers

WINDSHIELD WASHERS

LIGHTING CONTROL

AUTOLAMPS (IF EQUIPPED)

Lighting

INSTRUMENT LIGHTING DIMMER

HEADLAMP EXIT DELAY

DAYTIME RUNNING LAMPS (IF

AUTOMATIC HIGH BEAM CONTROL (IF EQUIPPED)

FRONT FOG LAMPS (IF EQUIPPED)

DIRECTION INDICATORS

INTERIOR LAMPS

POWER WINDOWS

Windows and Mirrors

GLOBAL OPENING AND CLOSING

EXTERIOR MIRRORS

INTERIOR MIRROR