Ford 2002 Excursion, 2002 F-250, 2002 F-350, 2002 F-450 Owner's Manual

Table of contents

Introduction 2

Diesel information 4

Warning lights 7

Starting 9

Driving tips 12

General maintenance information 16

Scheduled maintenance 32

Minor troubleshooting guide 33

Capacities and specifications 36

Service points 38

All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company. Ford may change the contents without
notice and without incurring obligation.

Copyright © 2000 Ford Motor Company

1

Introduction

The following warning may be required by California law:

California Proposition 65 Warning: Diesel engine exhaust, some

of its constituents, and certain vehicle components contain or
may emit chemicals known to the State of California to cause cancer or
birth defects or other reproductive harm.

Your new diesel engine will feel, drive and function somewhat differently
than a gasoline engine. Therefore it is very important that you read and
thoroughly familiarize yourself and others operating the vehicle with this
guide.

This guide will acquaint you with the Power Stroke (7.3L DIT) diesel
engine. It provides recommendations on engine care and operating
procedures. For complete vehicle information, also refer to the Owner
Guide included with the vehicle. It also describes equipment and gives
specifications for equipment that was in effect when this guide was
approved for printing, and should be considered a permanent part of the
vehicle.

Some aftermarket products may cause severe engine and/or
transmission damage. There are various manufacturers offering
devices to increase turbocharger boost, exhaust brakes to
increase stopping/hauling capacity or other such devices to
increase the power/torque of the 7.3L engine. Many owners’ past
experience with these products has been very poor. Severe
powertrain damage may result from the use of these aftermarket
products which will not be covered by the Ford warranty.

Ford may discontinue models or change specifications without any notice
and without incurring obligations.

IMPORTANT NOTICE

Ford vehicles are suitable for producing ambulances only if equipped
with the Ford Ambulance Preparation Package. In addition, Ford
urges ambulance manufacturers to follow the recommendation of the

Ford Incomplete Vehicle Manual, Ford Truck Body Builder’s Layout
Book (and pertinent supplements) and the “Qualified Vehicle Modifiers
Guidelines.” Using a Ford vehicle without the Ford Ambulance
Preparation Package to produce an ambulance voids the Ford warranty

and could result in elevated underbody temperatures, fuel
overpressurization and the risk of fuel expulsion and fires. To determine
whether the vehicle is equipped with the Ford Ambulance Preparation

2

Introduction

Package, inspect the information plate on the driver’s side door pillar.
Contact the manufacturer of your vehicle to determine whether the
ambulance manufacturer’s followed Ford’s recommendations.

WARNING: Engine exhaust, some of its constituents, and

certain vehicle components contain or emit chemicals known to
the State of California to cause cancer and birth defects or other
reproductive harm. Certain fluids contained in vehicles and certain
products of component contain or emit chemicals known to the State
of California to cause cancer and birth defects or other reproductive
harm.

WARNINGS

Throughout this guide, you will find warnings. Warnings remind you to
be especially careful to avoid personal injury.

NEW VEHICLE BREAK-IN

Your vehicle does not need an extensive break-in. Try not to drive
continuously at the same speed for the first 1 600 km (1 000 miles) of
new vehicle operation. Vary your speed to allow parts to adjust
themselves to other parts.

Drive your new vehicle at least 800 km (500 miles) before towing a
trailer.

Do not add friction modifier compounds or special break-in oils during
the first few thousand kilometers (miles) of operation, since these
additives may prevent piston ring seating. See “Engine oil” in the
General Maintenance Information chapter for more information on oil
usage.

3

Diesel information

DIESEL ENGINE INFORMATION

The diesel engine fuel system consists of:

• a frame-mounted electric fuel supply pump

• an engine mounted fuel filter/water separator

• a fuel restriction sensor

• a unit injector for each cylinder

The combination fuel filter/water separator removes both water and
impurities from the fuel. The filter should be changed at the
recommended service interval. Refer to the “Service Guide” for more
information. The filter bowl should be drained at regular intervals or
when the “WATER IN FUEL” light illuminates in the instrument cluster.

The fuel injectors are located in the center of the combustion chambers
in the cylinder head between the rocker arm assemblies. The glow plug
system and fuel injection system are controlled through the powertrain
control module (PCM).

Fuel is drawn from the fuel tank by a frame-mounted electric fuel pump.
The fuel pump provides pressurized fuel to the engine and is
electronically controlled by the fuel pump PCM relay. The fuel pump
contains a pressure relief valve for overpressure protection in the event
of restricted flow.

Lubrication system

It is important to change the engine oil at the recommended service
intervals, because oil viscosity is important in maintaining the oil
pressure required to actuate the fuel injectors. Extended oil change
intervals can negatively affect engine performance and fuel economy.

Pressurized oil from the turbocharger is also used to actuate an exhaust
backpressure warm-up system (if equipped). Pressurized oil from the
turbocharger is routed to the exhaust backpressure actuator. During
exhaust backpressure operation, the engine’s sound will be altered and
you may notice a change in engine performance while it’s engaged. This
function occurs only during cold weather warm-up cycle.

4

Diesel information

Fast start glow plug system

The glow plug system consists of:

• eight glow plugs

• the glow plug relay

• engine oil temperature (EOT) sensor

• barometric pressure (BARO) sensor

The glow plug system is electronically controlled by the PCM. The PCM
energizes the glow plugs immediately after the ignition is placed in the
ON position, then determines how long the glow plugs will be on
according to the EOT and BARO sensors. The required time for the glow
plugs to be energized decreases as the engine oil temperature and
barometric pressure increase.

Engine cooling system

The cooling system contains an engine oil cooler which is mounted to
the side of the cylinder block. The cooler’s function is to regulate engine
oil temperature.

Engine governed speed

The engine governor is controlled by the PCM. The PCM controls fuel
input to limit maximum engine speed. It will not, however, prevent
engine overspeeding resulting from downshifting at high vehicle speed or
by descending steep grades at too high a vehicle speed for the selected
transmission gear.

For maximum vehicle speed in various gears, refer to the “Transmission
shift speed” chart in the Driving tips chapter. Do not exceed 3,600 rpm.
Maximum engine governed speed is 3,000–4,000 rpm depending on
engine load. Excessive rpm can only be achieved by manually
downshifting at too high of a vehicle speed.

Operating the engine beyond the governed speed can cause severe
engine damage.

5

Diesel information

Air filter restriction gauge

The restriction gauge, located on
the clean-air side of the air cleaner
upper housing, shows if the air filter
is clogged. Refer to “Engine
Compartment” in Service Points
chapter.

R

G

E

A

T

L

U

I

G

F

E

R

I

A

C

R

H

E

A

T

N

L

I

G

F

E

E

F

G

N

A

H

C

I

L

T

E

R

The air filter element should be
replaced when the colored band on
the gauge reaches the CHANGE
FILTER mark. Engine performance
and fuel economy are adversely
affected when maximum restriction
is reached. After servicing the air
filter element, reset the restriction
gauge by pressing the button the
end of the gauge.

R

G

E

A

T

L

U

I

G

F

E

R

I

A

C

H

A

R

N

E

G

T

L

E

I

F

F

I

L

E

G

N

A

H

C

T

E

R

6

ECONOLINE

F–250/350/450/550, EXCURSION

Warning lights

WAIT TO START

With the key in the ON position, the
WAIT TO START light will illuminate
if glow plug heat is necessary as a
starting aid. Wait until the light goes
off before starting. The light should
always illuminate briefly, when the ignition key is in the ON position. If
the light does not illuminate, there may be a problem. Refer to the
Starting chapter in this guide. After the engine starts, the light should
remain off.

The light should always illuminate at least momentarily when the engine
is cold and the ignition is turned to ON. If it does not illuminate, the
glow plug system should be checked and repaired promptly to avoid
difficulty in cold starting.

WAIT

TO

START

7

Warning lights

WATER IN FUEL

During refueling, it is possible for
water-contaminated diesel fuel to be
pumped into your tank. Your vehicle
fuel system is equipped with a fuel
filter/water separator to remove
water from the fuel. The WATER IN FUEL light will illuminate when the
ignition is turned to START (as part of the light function check) and
when the fuel filter/water separator has a significant quantity of water in
it.

If the light illuminates when the engine is running, stop the vehicle as
soon as safely possible, shut off the engine, then drain the filter bowl.
Refer to the General maintenance chapter for drain procedure.
Allowing water to stay in the system could result in extensive damage to,
or failure of, the fuel injection system.

Do not drain the water separator while the engine is running.

Fuel may ignite if the separator is drained while the engine is
running or the vehicle is moving.

WATER

IN

FUEL

8

Starting

STARTING THE ENGINE

Read all starting instructions carefully before you start your vehicle.
For temperatures below 0°C (32°F), the use of the correct grade engine

oil is essential for proper operation.
If your vehicle is equipped with a manual transmission, make sure the

parking brake is set fully before you turn the key. Depress the clutch
pedal and place the gearshift in the neutral position. The clutch must be
fully depressed in order to operate the starter. Do not press the
accelerator during starting.

If your vehicle is equipped with an automatic transmission, ensure the
gearshift lever is in P (Park) and the parking brake is set before you turn
the key. Do not press the accelerator during starting.

COLD WEATHER STARTING

Do not crank the engine for more than 30 seconds at a time as starter
damage may occur. If the engine fails to start, turn the key to OFF and
wait 30 seconds before trying again.

Do not use starting fluid such as ether in the air intake system (see Air
Cleaner Decal). Such fluid could cause immediate explosive damage to
the engine and possible personal injury.

Do not add gasoline, gasohol or alcohol to diesel fuel. This practice
creates a serious fire hazard and causes engine performance problems.

1. Make sure all vehicle occupants have buckled their safety belts. For
more information on safety belts and their proper usage, refer to Seating
and safety restraints chapter in the owner guide.

2. Make sure the headlamps and vehicle accessories are off.

3. Turn the key to the ON position.
When the WAIT TO START light
goes off, turn the key to START.
(For Canadian vehicles, the daytime
running lamps will be on if the
parking brake is not applied and the key is turned to ON.)

4. When the engine starts, release the key. The glow plugs will continue
to be activated for up to two minutes. If the engine is not started before
the activation ceases, the glow plug system must be reset by turning the
ignition key to OFF.

WAIT

TO

START

9

Starting

5. After the engine starts, allow it to idle for about 15 seconds. (Do not
increase engine speed until the oil pressure gauge indicates normal
pressure.)

STOPPING THE ENGINE

Turn the ignition to OFF. To prolong engine life (after extended high
speed or maximum GVW operation), it is recommended that a hot engine
be allowed to operate at low idle for about 7–10 minutes which would
allow sufficient time for the turbocharged engine to cool down.

COLD WEATHER OPERATION

Changing to a lighter grade engine oil also makes starting easier under
these conditions. Refer to “Engine Oil Specifications” in the General
maintenance information chapter.

At temperatures below –7°C (20°F), Number 2–D diesel fuel may thicken
enough to clog the fuel filter. Your engine is equipped with a fuel
filter/heater/water/separator to keep the wax melted which will help
prevent fuel filter clogging. However, if the engine starts but stalls after a
short time and will not restart, the fuel filter may be clogged. For best
results in cold weather, use Number 1–D diesel fuel or “winterized”
Number 2–D diesel fuel which has an additive to minimize wax
formation.

Your vehicle is also equipped with a bypass relief valve, located on the
in-tank fuel sending unit, which provides fuel flow to the engine if the
fuel pickup should become plugged by ice or wax. To allow this bypass
valve to function and avoid engine fuel starvation, it is recommended
that, during cold weather operation 0°C (32°F) or below, the fuel level in
your tank should not be allowed to drop below 1/4 full. This will help
prevent air from entering the fuel system and stalling the engine.

In cold weather below 0°C (32°F) your diesel engine will slowly increase
to a higher idle speed if left idling in P (Park). The sound of the engine
may change also, as an exhaust device engages to improve heater
performance and reduce exhaust smoke.

Operation in snow

Vehicle operation in heavy snowfall or in dry loose snow that may swirl
around the front of the vehicle may feed excessive amounts of snow into
the air intake system. This could plug the air cleaner with snow and
cause the engine to stall.

10

Starting

Operation in standing water

Ingestion of water into the diesel engine can result in immediate and
severe damage to the engine. If driving through water, slow down to
avoid splashing water into the intake. If the engine stalls, and ingestion
of water into the engine is suspected, do not try to restart the engine.
Consult your dealer for service immediately. Follow the cylinder
compression test procedure outlined in the Workshop Manual, then
check the engine oil for contamination.

Engine block heater (if equipped)

Refer to the Starting chapter in your Owner Guide.

11

Driving tips

DUAL FUEL TANK SELECTOR CONTROL (IF EQUIPPED)

If your vehicle is equipped dual fuel tanks, you will have a selector
control, located to the right of the steering wheel, which allows you to
draw fuel from either tank. Your fuel gauge will display the amount of
fuel in the currently selected tank.

Fuel level indication is delayed for several minutes when the tank
selector switch is actuated. Fuel level indication can be obtained
immediately by turning off and restarting the engine.

MANUAL TRANSMISSION SHIFT SPEEDS

Do not overspeed the engine when going downhill or steep grades. If
equipped, use the tachometer and do not allow engine speed to exceed
the redline area. Operating the engine beyond the recommended speeds
can cause severe engine damage.

If your vehicle is an F-Series equipped with a manual
transmission, your vehicle has an electronic operating strategy
which protects the engine system when the engine is operating
with high coolant temperatures; fueling to the engine will be
modified to prevent damage to the engine. Some power loss may
be experienced if the vehicle is overloaded.

12