Food Warming Equipment Company PH-BCC-FS Service Manual

Home Page
Product Overview
Specification Page: S5–5
PROJECT: MODEL: QUANTITY: ITEM NO:
Quick Link Directory
BAKE CENTER COMPANION PROOFER/HEATERi
Humidified Holding System for Various Size Trays and Pans
“PH-BCC SERIES”
Universal Proofer/Heater supports the following Convection Ovens:
Bakers PrideBlodgettGarlandMontagueSouthbendVulcan
May stack with other brand Convection ovens. Consult factory.
®
®
®
®
®
®
BAKE CENTER COMPANION
Shown with optional shelves.
Shown with convection oven (in phantom)
provided by another manufacturer.
Space saving solution! Multi-purpose cabinet for proofing and heated holding – as well as a support base for your convection oven!
TM
Proofer/Heater Cabinets Section 5
PH-BCC-FS
FWE’s Proofer/Heater cabinets are perfect companions to your convection oven! This multi-purpose cabinet is built specifically to support the weight of your convection oven while providing a built-in proofing system.FWE’s Proofer/Heater Companion cabinets give you a faster pre-heat proofing time and maintain a 95°F - 95% heat/humidity balance for uniform raised dough results.
These units can double as full-time, heated serving cabinets, as well.The built-in “Proofing” System conditions the cabinets’ interior holding environment by gently circulating hot, moist air, surrounding the food and keeping it fresh and hot for hours.
Built strong like no others on the market, FWE’s Bake Center Companion will provide years of dependable service for your operation.
® Registered trademarks of manufacturers of convection ovens.
PH-BCC-HS
Shown with optional shelves.
Shown with Lexan Door and Left Hand
Door Hinging optional accessories.
Proofing/holding system
Separate controls for heat and humidity
Removable, oversized humidity reservoir
Full range thermostat adjustable to
actual
temperature
All stainless steel
All welded construction - no rivets
Tubular stainless steel welded base frame
Heavy-duty polyurethane casters
Up-front, recessed controls
Heavy-duty hinges
Positive close door latch
Hi-temp door gasket
Fully insulated throughout
Universal tray slides
Two year limited warranty
Stainless
U
U
®
L
C
L
®
Steel
made to serve you better
NSF
®
PROJECT: MODEL: QUANTITY: ITEM NO:
SPECIFICATIONS:
6'
5'
4'
"H"
3'
2'
1'
PH-BCC-FS PH-BCC-HS
For Full Size For Half Size
Convection Oven Convection Oven
CAPACITIES @ 4.5" SPACINGS
MODEL NUMBER
PH-BCC-FS
For Full Size
PH-BCC-HS
For Half Size
[A] Uprights punched on 1-1/2" centers. Tray slides are adjustable. [B] Universal Tray slides accommodate (1) 18" x 26", (2) 14" x 18", (2) 12" x 20", (2) 12" x 18",
(1) 20" x 22", (2) 10" x 20" trays and/or pans.
Pass-thru Door [add “P”] is available on all model sizes. Add 2.5" to depth dimension.
See-thru Lexan Door [add “L”] is available on all model sizes.
TRAY SLIDES PROVIDED
4 pair
4 pair
[A]
[B]
"D"
DIMENSIONS IN. (mm)
HIGH
DEEP
"H"
"D"
33"
31"
(838)
(787)
33"
31"
(838)
(787)
BAKE CENTER COMPANION
DOOR SWING: 22.25"
WIDE
"W"
38.25" (972)
30.25" (768)
"W"
TOP
NO.
OF
DOORS
1 5"
1 5"
CLASS 100
SHIP WT .
CASTER
SIZE
165 (75)
165 (75)
LBS. (KG)
*PERFORMANCE VALUES
T
190°
RECOVERY
170°
E
M
P
PRE-HEAT
RECOVERY
* Values are for largest model listed.
150° 130° 110°
70°
5 10 15 20 25 30 35
ELECTRICAL DATA
VOLTS 120
WATTS 1650
AMPS 13.75
HERTZ 50 / 60
PHASE Single
NEMA PLUG
PREHEAT
TIME
75°F to 160°F APPROX. 25 MIN.
120°F to 160°F APPROX. 6 MIN.
G
5-15P
Dedicated circuit.
Specify Brand and Model of Convection Oven at time of order:
Bakers Pride
Southbend
CONSTRUCTION. Heliarc welded, single unit construction of stainless steel; 20-gauge polished exterior, 22-gauge stainless steel interior with easy-to-clean coved corners. Welded tubular base frame shall be 1" square, heavy gauge stainless steel tubing, with 10-gauge stainless steel reinforcing plates at corners, reinforced top deck for use of heavy loads. INSULATION. “Ultra-Guard” UG-26 high density fiberglass insulation throughout; top, back, bottom, sides and door(s). DOORS AND LATCHES. Flush mounted, stainless steel insulated doors. High temperature gasket sealed; gasket shall be cabinet mounted. Each door shall have two (2) heavy-duty edgemount die cast hinges. Door latch shall be edgemounted, full grip, and positive closing. The hinge and latch mountings are reinforced
®
®
Blodgett
Vulcan
CASTERS.
tire casters in a configuration of two (2) rigid and two (2) swivel with brake. Casters shall have a reinforced yoke mounted to 10-gauge caster plate. The caster mounting plate shall be secured to a 10-gauge stainless steel reinforcing stress plate via welded in place stainless steel studs. The reinforcing stress plates shall be welded to the heavy gauge tubular frame of the unit. TRAY SLIDES. Welded rod-style tray slides are stainless steel for greater durability and sanitation. Fully adjustable / removable and designed to give secure bottom tray support. Removable stainless steel uprights shall be punched on 1.5" (38mm) spacings, o.c., for easy tray adjustment, and shall easily lift off heavy-duty stainless steel brackets without the use of tools for cleaning.
with stainless steel backing plates.
®
®
Garland
Other: _______________________
Maintenance free polyurethane
®
PROOFING SYSTEM/CONTROLS. Built in humidified holding system shall include two (2) separate long life Incoloy nickel-chromium alloy heating elements per cavity; separate, adjustable controls shall be provided for each function. One to control the interior air temperature, and one to control the interior air moisture with hydro immersion waterbath. An oversized and baffled, stainless steel water reservoir shall be removable for ease of cleaning/sanitation. System shall have a Hi-Temp, self-lubricated, impedance protected fan-cooled blower motor for moist air distribution. Controls shall be up-front, recessed and shall include a full range thermostat adjustable to actual temperature. Thermostat shall include temperature scale marked in ten degree increments (F/C) from 90° to 190°F (30° to 90°C). An operational range thermometer, adjustable moisture control (Low to High) with “P” to indicate “Proof” position, 20 amp ON/OFF power switch, humidity cycle light, and thermostat cycling light shall also be included. ELECTRICAL CHARACTERISTICS. 3 wire grounded 10 foot extension power cord and plug, side mounted for safety. See electrical data chart above for amperage and receptacle configuration. Dedicated circuit.
Montague
FWE Products are used by major companies world-wide.
®
We can modify, design, or custom build equipment to fit your special requirements.
Optional Accessories:
Digital thermometer
Mechanical timer
220 volt, 50/60 Hz, single phase
CE compliant
Heat retention battery
See-thru lexan door
Key locking door latch
Magnetic latch
Paddle latch
Padlocking transport latch
Left hand door hinging
Security packages
All swivel or larger casters
Door edge trim
Cold plate cartridge
Floorlock (requires 6" casters)
Extra tray slides
6" adjustable legs
Full extension bumper
Heavy-duty push bars
Food Warming Equipment Company, Inc.
P.O. Box 1001 Crystal Lake, IL 60039 USA 800-222-4393; 815-459-7500 Fax: 815-459-7989
Manufacturing Facilities: 7900 S. Route 31 Crystal Lake, IL 60014 USA www.FWE.com sales@fweco.net
FWE products may be covered under one or more of the following U.S. patents: 288,299;238,300;3,952,609;4,192,991.
All specifications subject to change without notice. ©10D Food Warming Equipment Company. Inc.
Loading...