Food Warming Equipment Company P-120-2 Service Manual
Home Page
Product Overview
Specification Page: S1–7
PROJECT: MODEL: QUANTITY: ITEM NO:
Quick Link Directory
HUMI-TEMP MOBILE BANQUET CABINETSi
“Easy Load” Full Radius Maneuvering for Pre-Plated Meals
“P-2 SERIES”
To achieve
maximum capacity,
maximum cover size
is 11" diameter.
For 12.375" cover size,
refer to “XL Series”.
(See Specification Page: S1–8)
E-Z Turn 6-Caster Configuration
Featuring “Easy Load”
and unloading 2 door design
and the ease of 6-caster
configuration maneuvering.
TM
Banquet Cabinets
Section 1
Take the worry out of serving delays and last minute
arrivals with FWE’s P-2 Series banquet cabinets.
The P-2 Series comes standard with a six caster
configuration for increased maneuverability and side
by side full doors for easy loading and unloading.
The series also features FWE’s patented “Humi-Temp”
Heat/Humidity System which eliminates hot and cold
gently
spots by
the interior of the cabinet. Humidity can be added
to preserve the moisture content of the food keeping
the food fresh and hot for hours.
The heat system is built into the cabinet to reduce
maintenance and cleaning costs. Clean up is
effortless. The controls are upfront and eye-level and
feature a full range thermostat adjustable to actual
temperature so they are easy to see and operate.
Our cabinets are built tough using stainless steel
throughout. Welded construction and our exclusive
tubular stainless steel base frame ensure that our
cabinets will withstand the most demanding use.
And when it comes to selection, no one offers more
than FWE. We offer sizes and capacities to fit any
operation. Make your choice FWE . . . the “Choice of
the Professionals”.
circulating hot, moist air throughout
P-200-2
◊
E-Z Turn 6-caster configuration
◊
“Humi-Temp” built-in heat system
◊
Removable humidity reservoir
◊
Heavy-duty “No Sag” removable shelves
◊
Full range thermostat adjustable to
actual
temperature
◊
Recessed eye-level controls
◊
All stainless steel
◊
All welded construction - no rivets
◊
Tubular stainless steel welded base frame
◊
Full extension bumper
◊
Heavy-duty polyurethane casters
◊
Heavy-duty hinges
◊
Positive close door latch
◊
Hi-temp door gasket
◊
Fully insulated throughout
◊
Two year limited warranty
U
®
L
U
C
L
®
Stainless
Steel
made to serve you better
NSF
®
PROJECT: MODEL: QUANTITY: ITEM NO:
SPECIFICATIONS:
"W"
▲
▲
"D"
▼
6'
▲
5'
4'
3'
"H"
2'
1'
▼
TOP
P-120-2 P-144-2 P-180-2 P-200-2
COVERED PLATES:
11"
MODEL
NUMBER
P-120-2
- [A] [A] [B]
P-144-2
P-180-2
P-200-2
[A] Capacities when using covers depend on height of plate and cover. Capacities shown are based on plate and cover height
of 3.125" and 2.625" respectively. 11" diameter cover is maximum when not using carriers and stacking directly on shelves.
[B] Available with 5 shelf optional accessory (at time of order @ additional charge) with 9.75" shelf clearance
(installed at factory only). Covered plates then stack 3 high on each shelf. Carriers cannot be used with this optional accessory.
When ordering carriers - Specify ❏ CP for covered plates or ❏ UP for uncovered plates.
CANNED HEAT Adapter Package is NOT available for this model series.
COVER & PLATE HEIGHT:
3.125'' 2.625''
96 120 3 4
120 144 3 5
[A] [A] [B]
150 180 3 5
[A] [A] [B]
160 200 4 5
[A] [A] [B]
▲
DOOR SWING: 21.25"
DIAMETER
SHELVES
COVERED
PLATES
SHELF
STACKED
SIZE
HIGH
22.25"
x 44.375"
22.25"
x 44.375"
22.25"
x 54.75"
22.25"
x 54.75"
SHELF
CLEARANCE
(mm)
57.6"
13.7"
(1463)
(348)
16.6"
66.9"
(422)
(1699)
16.6"
66.9"
(422)
(1699)
13.7"
(348)
(1829)
EASY LOAD HUMI-TEMP BANQUET CABINETS
OVERALL EXTERIOR
DIMENSIONS IN. (mm)
DEEP
"D"
(730)
(730)
(730)
(730)
WIDE
"W"
54"
(1372)
54"
(1372)
64.5"
(1638)
64.5"
(1638)
HIGH
"H"
72"
28.75"
28.75"
28.75"
28.75"
CLASS 100
NO.
OF
CASTER
DOORS
SIZE
5" 2
6" 2
6" 2
6" 2
SHIP
WT .
LBS.
(KG)
370
(168)
440
(198)
490
(222)
535
(242)
PERFORMANCE VALUES*
T
190°
RECOVERY
170°
E
150°
130°
M
110°
P
PREHEAT
RECOVERY
* Values are for mid-size model listed.
VOLTS 120
WATTS 1600
AMPS 13.3
HERTZ 50 / 60
PHASE Single
NEMA
PLUG
Dedicated circuit.
**
Consult factory.
•
70°
5 10 15 20 25 30 35 40 45 50 60
ELECTRICAL DATA
Also available in 1600W, 13.3 amp, and 5-15P.
TIME
75°F to 170°F
APPROX. 45 MIN.
120°F to 170°F
APPROX. 12 MIN.
P-120-2
P-144-2
G
5-15P
P-180-2
P-200-2
120
2100
17.5
50 / 60
Single
G
5-20P**
•
PREHEAT
FWE Products are used by major companies world-wide.
We can modify, design, or custom build equipment to fit
your special requirements.
CONSTRUCTION. Heliarc welded, single
unit construction of stainless steel;
20-gauge polished exterior, 22-gauge stainless
steel interior with easy-to-clean coved corners.
Welded tubular base frame shall be 1" square,
heavy gauge stainless steel tubing, with
10-gauge stainless steel reinforcing stress
plates at corners.
INSULATION. “Ultra-Guard” UG-26 high
density fiberglass insulation throughout; top,
back, bottom, sides, and doors.
PUSH BAR HANDLES. Heavy-duty, solid
formed 1" x .375" thick; mounted at each end of
unit. Mountings reinforced with stainless steel
channel.
BUMPER. Solid 1.5" wide continuous
wraparound aluminum channel, bolted to frame,
with snap-in, non-marking replaceable vinyl
cushion. Full perimeter bumper extends beyond
doors, handles, etc., for added protection. Shall
be continuous, with corner cut-outs to facilitate
cleaning.
DOORS AND LATCHES. Flush mounted,
stainless steel insulated doors. High temperature
gasket sealed; gasket shall be cabinet mounted.
Each door shall have two (2) heavy-duty edgemount
die cast hinges. Magnetic door latch shall be
edgemounted and full grip. The hinge and latch
mountings are reinforced with stainless steel
backing plates.
CASTERS.
casters in a configuration of two (2) rigid and four (4)
swivel with brake. Casters shall have a reinforced
yoke mounted to 10-gauge caster plate. The caster
mounting plate shall be secured to a 10-gauge
stainless steel reinforcing stress plate via welded
in place stainless steel studs. The reinforcing stress
plates shall be welded to the heavy gauge tubular
frame of the unit.
SHELVES. Triple plated, welded rod-type shelves
shall be removable. Shelves shall be supported by
high strength, “no fall” 14-gauge die-formed stainless
steel brackets. Bottom shelf shall be equipped with
“lift-up” hooks for easy access to facilitate cleaning.
HEATING SYSTEM / CONTROLS. Patented built-in
“Humi-Temp” system shall include an Incoloy
nickel-chromium alloy heating element and
Hi-Temp, self-lubricated, impedance protected
fan-cooled blower motor. Cabinet shall have
humidifying chamber and drawer style baffled
humidifier pan. Both shall be stainless steel and
removable. Controls shall be up-front, recessed
Maintenance free polyurethane tire
and shall include a full range thermostat adjustable
to actual temperature. Thermostat shall include
temperature scale marked in ten degree
increments (F/C) from 90° to 190°F (30° to 90°C).
An operational range thermometer, power supply
light, thermostat cycling light,
ON/OFF switch
ELECTRICAL CHARACTERISTICS.
3 wire grounded 10 foot extension power cord
and plug, side mounted for safety. See chart above
for amperage and receptacle configuration.
Dedicated circuit.
Food Warming Equipment Company, Inc.
P. O. Box 1001
Crystal Lake, IL 60039 USA
800-222-4393; 815-459-7500
Fax: 815-459-7989
Manufacturing Facilities:
7900 S. Route 31
Crystal Lake, IL 60014 USA
www.FWE.com sales@fweco.net
are also included.
and 20 amp
Optional Accessories:
■
Digital thermometer
■
1500 or 2000 watt element
■
220 volt, 50/60 Hz, single phase
■
CE compliant
■
Heat retention battery
■
Dutch doors
■
Key locking door latch
■
Paddle latch
■
Padlocking transport latch
■
Left hand door hinging
■
Door edge trim
■
Security packages
■
Top corner bumpers
■
Larger or type of casters
■
Cold plate cartridge
■
Floorlock (requires 6" casters)
■
Extra shelves
■
Plate carriers: CP or UP
FWE products may be covered under
one or more of the following U.S. patents:
288,299;238,300;3,952,609;4,192,991.
All specifications subject to change without notice.
© 11J Food Warming Equipment Company. Inc.
Loading...