Food Warming Equipment UFS Service Manual

OPERATING

INSTRUCTIONS

TM

REFRIGERATORS

TEMP SETTING

R SERIES URS SERIES SR SERIES

RBQ-96 F SERIES UFS SERIES

&

FREEZERS

DEFROST

CYCLE

Press for

"ON DEMAND"

or Defrost

Override

FWE COLD-SERVE CABINETS

FWE’ s “COLD-TEMP”
Food Sentry System
keeps food cold or
fresh frozen —
without dehydration!

CONGRATULATIONS...

...and thank you for purchasing an FWE COLD-SERVE Refrigerator or
Freezer Cabinet.Your unit has been designed and manufactured under
rigid controls to assure you the most efficient service. It is a full time
unit, and may be used continuously.

Please take a moment to read through this booklet of important
information pertaining to your cabinet. By following a routine of
proper use and care described on the following pages, your cabinet
will last for many years.

IMPORTANT: Your Manufacturer Registration Card must be
returned within 30 days after initial delivery to put warranty into effect.

2

FOOD SENTRY CONTROLS

FWE MOBILE REFRIGERATORS AND FREEZERS

Q

UICK-START

Q

Q

GUIDE

“COLD-TEMP” FOOD SENTRY SYSTEM

POWER ON / OFF - Turns cabinet ON and OFF.

Also Changes Display to °Celsius or °Fahrenheit Scale:

You may change the Digital thermometer scale to either
°C or °F as follows:While unit is OFF, press and hold the

“ON/OFF” key

switch from

3

for five (5) seconds.The display will then

“dgF” to “dgC”

Power Indicator Light -

Indicates that the power is on.

Temp Display - Digital temperature display shows
the temperature of the cabinet.

You may change the Digital thermometer scale to
either °C or °F as follows:While unit is OFF, press
and hold the
The display will then switch from
Repeat to change scale again.

Cycling Indicator Light -

When light is
cabinet is cooling down to desired temperature.
When cooling elements are activated, light will

“ON”

come
temperature, and go
reached desired temperature.

. Repeat to change scale again.

“dgF” = Degrees
“dgC” = Degrees

“ON/OFF” key

“ON”

until cabinet has reached desired

Fahrenheit

Celsius

for five (5) seconds.

“dgF” to “dgC”

, this indicates that the

“OFF”

when unit has

.

TEMP SETTING - Raising the Temperature

Press to raise the temperature of the cabinet.

TEMP SETTING - Lowering the Temperature

Press to lower the temperature of the cabinet.

TEMPERATURE RECALL

Press to display either
actual temperature, or desired

Actual:

The factory default setting shows the actual internal cabinet temperature
and acts as a digital thermometer. A momentary touch of the
will recall the original dial setting.The display will then automatically return to the
actual internal temperature.

Set Point:

To have temperature read-out display the
press and hold the
display will flash either
To switch back again, repeat this step holding the
key for five (5) seconds.

Activated red light indicates DEFROST is in progress.

DEFROST CYCLE - “ON DEMAND” DEFROST

Press to ACTIVATE DEFROST at any time.
Press to CANCEL DEFROST in progress (Defrost Override).

“Actual Internal Cabinet”

“Set Point”

“Temp”

key for five (5) seconds.The fourth (4th) digit on the

“S”

(Set), or

“A”

(Actual) to indicate which mode is active.

temperature.

“Set Point”

“Recall Temp Set”

“Temp Recall”

temperature,

key

FWE MOBILE REFRIGERATORS AND FREEZERS

INSTALLATION

SERIAL AND MODEL NUMBER

These numbers are found on the nameplate (serial tag) affixed
to the unit.The serial tag is located by the electrical cord.
Please record them on the back of this booklet. When ordering
parts and/or ser vice, you will need to provide this information.
The voltage and amperage of the unit are also stamped on the
serial tag.

UNPACKING

After uncrating your cabinet, remove all tape and padding
which held all doors, shelves, racks, cord, etc., in place
during shipment.

ELECTRICAL REQUIREMENTS AND GROUNDING

FWE standard models operate on 110/120 volt,
60 Hz, 1 ph, A.C. (unless ordered otherwise), and are equipped
with a three prong grounding cord plug for your protection against
possible shock hazards. Be sure to plug only into a properly
grounded three prong wall receptacle. If you have any questions
with regard to adequate wiring or grounding in your building,
a qualified electrician should be contacted before using your
cabinet. The amperage of your cabinet is stamped on the
name plate attached to the unit.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE
THE GROUNDING PRONG FROM THE CORD PLUG.

WARNING: ONLY A QUALIFIED ELECTRICIAN SHOULD

ATTEMPT TO REPAIR OR REPLACE ELECTRICAL
COMPONENTS OR WIRING.

BE SURE THAT MODEL IS UNPLUGGED FROM ELECTRICAL
SOURCE BEFORE REMOVING CONTROL PANEL.

4