Food Warming Equipment MT Installation Manual

OPERATING

INSTRUCTIONS

MOISTURE-TEMP CABINETS

HEATED HOLDING

CABINETS

With Separate

Controls

For Heat and

Moisture

MTU SERIES

MT SERIES

Heat Basin Water Pan

Thermometer

Air Temperature
“HEAT” Control Dial

Air Temperature Cycling Light
Air Moisture Cycling Light

Air Moisture Control Dial
“P” to Indicates Proof Position

Main Power Switch

MOISTURE-TEMP CABINETS

Serial Tag

and

Parts List

Control

Panel

Uprights and

tray slides

remove and
adjust easily
without tools

Heat System

Tunnel

1 FWE MOISTURE-TEMP HEAT SYSTEM

12" x 20" Water Pan

and Heat Basin

Moisture

Drip Trough

With

Removable

Drain Plug

FWE MOISTURE-TEMP CABINETS

COMPLETE AND RETURN YOUR WARRANTY CARD

CONGRATULATIONS

...and thank you for purchasing an FWE MOISTURE-TEMP
cabinet. Your unit has been designed and manufactured under
rigid controls to assure you the most efficient service.

Please take a moment to read through this booklet of important
information pertaining to your cabinet. By following a routine
of proper use and care described on the following pages, your
cabinet will last for many years.

IMPORTANT: Your Manufacturer Registration Card must be
returned within 30 days after initial delivery to put warranty
into effect.

SERIAL AND MODEL NUMBER

These numbers are found on the nameplate (serial tag) affixed
near the rear of the unit. Please record them in this booklet,
in the space provided on page 9. When ordering parts and/or
service, you will need to provide this information. The voltage
and amperage of the unit are also stamped on the serial tag.

UNPACKING

After uncrating your cabinet, remove all tape and padding which
held all doors, shelves, racks, cord, etc., in place during shipment.

ELECTRICAL REQUIREMENTS AND GROUNDING

The amperage of your cabinet is stamped on the name plate
serial tag attached to the unit. FWE models are equipped with
a three prong grounding cord plug for your protection against
possible shock hazards. Be sure to plug only into a properly
grounded three prong wall receptacle. If you have any questions
with regard to adequate wiring or grounding in your building, a
qualified electrician should be contacted before using your cabinet.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE
THE GROUNDING PRONG FROM THE CORD PLUG.

WARNING: ONLY A QUALIFIED ELECTRICIAN SHOULD ATTEMPT
TO REPAIR OR REPLACE ELECTRICAL COMPONENTS OR WIRING.

BE SURE THAT MODEL IS UNPLUGGED FROM ELECTRICAL
SOURCE BEFORE REMOVING CONTROL PANEL.

2

FWE MOISTURE-TEMP CABINETS

CONTROL PANEL

EASY-TO-USE CONTROLS

The ON-OFF rocker switch
activates power to the cabinet.
An indicator light on the main
power switch tells you when
your cabinet is plugged into
a power source.
MOISTURE-TEMP is equipped
with two (2) heating elements
and two (2) separate controls
which regulate these elements.
This allows you to adjust the
temperature and humidity
desired for the food product
you are holding.
The air moisture knob adjusts
the amount of humidity in the
cabinet from 1-7.
A CYCLING light indicates
that this function is activated.

Thermometer

Air Temperature
“HEAT” Control Dial

Air Temperature Cycling Light
Air Moisture Cycling Light

Air Moisture Control Dial
“P” to Indicates Proof Position

Main Power Switch

The air temperature control
goes from 90°F to 190°F (30°C to 90°C),
and adjusts the amount of heat in the cabinet.

Adding water to the
cabinet air to keep foods moist. However, if dry heat is required,
it does not harm the cabinet to be used without water in the
water pan.

An operational range thermometer shows the actual internal
temperature of the cabinet.

Some units are equipped with an OPTIONAL ACCESSORY
TIMER, which may be set manually for up to 12 hours.

3 FWE MOISTURE-TEMP HEAT SYSTEM

12" x 20" pan, humidity will be added to the