FONESTAR TMRI-844, TPRI-845, TSRI-841 Instruction Manual

Download

Page 1

TMRI-844, TPRI-845, TSRI-841

WIRELESS PERSONAL MONITOR SYSTEM

40 PLL UHF 863-865 MHz CHANNELS

INSTRUCTION MANUAL

RI-840

MSHT-45P

MSHT-40M

TSI-40

Page 2

- 2-

e take this opportunity to thank you for buying this product.

We recommend you read the instruction manual before switching on the machine and follow the instructions t

hat are given. Keep the manual for future reference.

SECURITY AND THE ENVIRONMENT

ELECTRICAL SECURITY Check that the current in the mains connection where the machine is to be installed corresponds to the power supply of the machine. To avoid damaging the equipment, electrical shocks, ﬁre or physical injury when you connect or disconnect the equipment from the power supply, pull the plug ﬁrmly out of the mains socket holding the plug, never the cable. Always do this with dry hands. Keep the power supply cable far from sources of heat. Do not put heavy objects on top of it or change it. Clean dust and dirt off the power supply cable regularly. Do not open the machine; you could get an electric shock.

CAUTION While installing the machine, make sure it is switched off and unplugged. Do not open the machine. Touching the internal parts is dangerous and you could receive an electric shock. The machine must not be splashed or dripped on. Never place recipients with liquid inside on the machine. Do not place anything inside the machine.

LOCATION Place the equipment on a horizontal surface with enough space around it to allow ventilation. Avoid direct sunlight, heat sources and excessive dust. Do not place the machine near magnetic ﬁelds or static electricity. Do not use surfaces which vibrate or receive impact. Do not pile machines on top of one another.

VENTILATION Never block or cover the ventilation slits on the machine. Do not expose it to direct sunlight or place it near sources of heat.

PERIODS OF INACTIVITY When the machine is not going to be used for a long period of time, disconnect it from the mains. If you are using an adapter, take into account that it will continue using electricity even if the machine is switched off. If it is not going to be used for a long period of time, disconnect it from the mains.

THE ENVIRONMENT To save energy, switch the machine off when you are not going to use it for a long time. The machine could contain substances that are harmful to the environment or human health. To minimize the effect of these substances the machine must be correctly managed and recycled when you decide to dispose of it. When you dispose of it remember: it cannot be thrown into a conventional rubbish bin. If it contains or uses batteries, these must be disposed of separately. The machine (without batteries) must be disposed of correctly. Put it in a container specially intended for the collection of electronic and electrical appliances, at the dump or hand it over to the dealer when you purchase similar equipment, so that the dealer can dispose of it correctly (at no added cost).

Page 3

SIGNIFICANCE OF THE SYMBOLS ON THE MACHINE*

The symbol formed by the expression “Class 1 laser product” written in a rectangle indicates that visible or invisible laser radiation could be produced. Avoid direct expose to the laser.

The symbol formed by a ray of lightening inside a triangle shows that the machine has connection terminals or a circuit with areas with a current which could cause an electric s

hock, even in normal working conditions.

The symbol formed by an exclamation mark in a triangle shows that the instruction manual must be referred to for information on how the machine works and its use.

The symbol formed by one square inside another square shows that the machine has double electrical insulation.

The European Community symbol shows that the machine complies with the current European Union legislation, as well as its transposition to local legislation.

The symbol of a rubbish bin crossed out and over a horizontal line shows that when the product is disposed of it must be done properly, placing it in a special selective electronic and electrical equipment container or through a dealer when purchasing a similar product, at no additional cost. It also shows that the machine was put on the market after 13th August 2005 (European Community Directive 2002/96/CE of Electrical and Electronic recycling, and its Spanish equivalent R.D.208/2005).

In accordance with what is set out in the aforementioned decree, FONESTAR is registered in the RAEE (Registro de Aparatos Eléctricos y Electrónicos) in a special section REI (Registro de establecimientos Industriales), with the entry number 001851.

*It is possible that some of these symbols do not appear on the machine.

EXEMPTION OF LIABILITY

The characteristics of the equipment and the content of the manual can change without forewarning. FONESTAR, S.A. does not assume responsibilities regarding the inappropriate use of the equipment or the information supplied in this instruction manual, and speciﬁcally disclaims any implied liability for marketability or ﬁtness for any other use.

- 3-

Page 4

DESCRIPTION

ireless personal monitor system for audio signal transmission in the band UHF 863-865 MHz. The system is composed of a wireless in ear belt-pack monitor receiver (mod. RI-840) with silicone rubber earphones and a

wireless hand-held microphone transmitter (mod. MSHT-40M) or a tie-clip microphone (mod. MSHT-45P)

ith wireless belt-pack transmitter, depending on the model chosen.

The system has 40 transmission channels in the band UHF 863-865 MHz, with PLL frequency control which a

llows a transmission channel free of interference to be easily selected.

t is possible to use multiple receivers (RI-840) in the same channel with one transmitter.

CONTROLS AND FUNCTIONS

RI-840 Wireless in ear belt-pack monitor receiver with headphones.

1.- Information display: displays information on tuned frequency, channel number, battery level, RF signal

level and audio signal level. If the level of the batteries is low, the display will light up red.

2.- w/s: allow menu options to be selected in order to conﬁgure the wireless belt-pack receiver.

3.- SET: allows selection among the different conﬁguration options: channel number and frequency, RF

transmission level (high/low), battery type selection (1.2 V - rechargeable/1.5 V - alkaline) to display the battery level correctly and lock the receiver. In order to do so, press the SET button repeatedly and use the w/s buttons to select the options.

4.- Battery compartment: uses two 1.5 V LR6-AA batteries, alkaline or rechargeable.When inserting the

batteries, make sure the polarity is correct.

5.- HEADPHONES OUTPUT: select the type of headphone output signal, single (L+R channels in left earphone)

or double (L+R channels in both earphones).

6.- Contacts to recharge the rechargeable batteries of the wireless receiver in the recharge docking station mod.

MSC-2.

7.- Antenna.

8.- VOL: wireless belt-pack receiver volume control.

9.- 3.5 mm stereo jack connector for connecting headphones/recording. If you wish to record a signal

received by the receiver RI-840, connect the recording equipment to the headphone output or use an adapter to be able to use the headphone signal and the recorder simultaneously.

10.- POWER: receiver on/off switch.

Note: when the SET button is pressed to conﬁgure the different parameters of the receiver, a MUTE indicator

appears in the display and the receiver will not receive audio while the parameters are being conﬁgured.

- 4-

Page 5

SHT-40M Wireless hand-held microphone transmitter

1.- Grille: protects the microphone capsule and helps to reduce noises from breathing or the wind blowing.

2.- Display: displays information on the tuned frequency, channel number, battery level, RF signal level and audio signal level. If the battery level is low, the screen will light up red.

3.- Battery compartment: unscrew this cover to access the battery compartment.

4.- GAIN: adjust the sensibility of the audio input.

5.-

: hand-held microphone on/off switch.

6.- Battery compartment: use two 1.5 V LR6-AA type batteries, alkaline or rechargeable. When inserting the batteries, make sure that the polarity is correct.

7.- SET: allows selection among the following conﬁguration options: channel number and frequency, RF transmission level (high/low), battery type selection (1.2 V - rechargeable/1.5 V - alkaline) to display the battery level correctly and lock the microphone transmitter. In order to do so, press the SET button repeatedly and use the w/s buttons to select the options.

8.- w/s: allow selection of the menu options to conﬁgure the hand-held wireless microphone.

9.- Contacts to recharge the wireless microphone’s rechargeable batteries in the recharge docking station mod. MSC-2.

Note: when the SET button is pressed to conﬁgure the different microphone parameters, a MUTE indicator

appears in the display and the microphone does not transmit audio while the parameters are being conﬁgured.

- 5-

Page 6

- 6-

SHT-45P Tie-clip microphone with wireless belt-pack transmitter

1.- Display: displays information on the tuned frequency, channel number, battery level, RF signal level and audio signal level. If the battery level is low, the screen will light up red.

2.- w/s: allows selection of required optionsin order to conﬁgure the wireless belt-pack microphone.

3.- SET: allows selection among the different conﬁguration options: channel number and frequency, RF transmission level (high/low), battery type selection (1.2 V - rechargeable/1.5 V - alkaline) to display the battery level correctly and lock the receiver. In order to do so, press the SET button repeatedly and use the w/s buttons to select the options.

4.- Battery compartment: use two 1.5 V LR6-AA batteries, alkaline or rechargeable. When inserting the batteries, make sure the polarity is correct.

5.- Antenna.

6.- VOL: wireless belt-pack transmitter volume control.

7.- 3.5 mm mono jack connector for connection of microphone or required audio source.

8.- POWER: transmitter on/off switch.

9.- LINE/MIC: input signal sensitivity selector.

10.- Contacts to recharge the wireless microphone’s rechargeable batteries in the recharge docking station mod. MSC-2.

Note: when the SET button is pressed to conﬁgure the different parameters of the microphone, a MUTE

indicator appears in the display and the microphone will not receive audio while the parameters are being conﬁgured

Page 7

SI-40 UHF transmitter for desktop or installing in 1 U 19" rack

RONT PANEL

1.- Headphone output volume control.

2.- Headphone output for monitoring the signal to be transmitted.

3.- Information display: displays information about input and output signals, frequency, etc.

A. RF: radio frequency signal level indicator. B. AF: audio signal level indicator. C. FREQ: indicates that the information shown on the display is the transmission frequency. D. CHAN.: indicates that the information shown on the display is the transmission channel number. E. Conﬁguration information. F. MUTE: indicates that the signal is cut off during the conﬁguration of new parameters.

4.- SET: allows selection among the following conﬁguration options: channel number and its associated frequency (from CH1 to CH40), RF emission level (low, mid or high) and conﬁguration locking (LOCK/UNLOCK).

5.- w/s: allows selection of required options for the conﬁguration of the transmitter.

6.- L: wireless transmitter left channel volume control.

7.- R: wireless transmitter right channel volume control.

8.- POWER: transmitter on/off switch.

REAR PANEL

1.- Power supply

2.- AF-IN (STEREO): line level signal input, 3.5 mm stereo jack connector.

3.- AF IN (R): microphone/line level signal input, 6.3 mm mono jack connector.

4.- AF IN (L): microphone/line level signal input, 6.3 mm mono jack connector.

5.- Gain selector of inputs AF IN (L) and AF IN (R).

6.- TX-ANT: antenna connector.

- 7-

Page 8

- 8-

INSTALLATION AND CONNECTION

I-840 Wireless in ear UHF belt-pack monitor receiver with earphones

1.- Insert the batteries in the battery compartment respecting the polarity indicated on it. If rechargeable batteries have been used, they can be recharged following the instructions in the Rechargeable battery section.

.- Connect the earphones to the headphone output. If you wish to record a signal received by the receiver

I-840, connect a recording device to the headphone output or use an adapter to be able to use the

headphone signal and the recorder simultaneously.

3.- Select the type of headphone output signal required with the HEADPHONES OUTPUT selector, single (mono) or double (stereo).

MSHT-40M Wireless hand-held transmitter microphone

2.- Adjust the sensitivity of the audio input using the GAIN control.

MSHT-45P Tie-clip microphone with wireless belt-pack transmitter

2.- Connect the tie-clip microphone or the required audio source.

3.- Place the selector on the rear part of the tie-clip microphone in the LINE or MIC position depending on the type of signal you have connected to the input. Select LINE if connected to an audio source with line level or MIC if connected to a microphone.

TSI-40 UHF transmitter for desktop or installing in 1 U 19" rack

1.- Connect the audio sources on the rear of the transmitter and the mains adapter provided. Place the selector on the rear part of the device in the 0 dB or -20 dB position depending on the type of signal that you have connected to the AF IN (L) and AF IN (R) inputs. Position the selector in 0 dB for a source with line level and in -20 dB if a microphone was connected.

2- Place the device on a flat surface or in a 19" rack using the mounts supplied with the device.

Page 9

- 9-

INSTRUCTIONS FOR USE

RF CHANNEL SELECTION FOR TRANSMISSION/RECEPTION

The transmitter (hand-held microphone or belt-pack microphone) and the receiver (belt-pack in ear monitor) must be tuned to the same channel. Select a channel that is free of interference in the receiver and select the same channel in the transmitter. If you wish to use 2 or more transmitter/receiver monitor systems simultaneously observe the following indications to avoid interference:

- Use radio frequency channels with the maximum separation between them. Bear in mind the carrier frequencies of each channel, as is shown in the table below:

- It is possible to use multiple receivers (RI-840) in the same channel with one transmitter.

RECHARGEABLE BATTERIES

Insert the batteries in the battery compartment respecting the polarity in it. In order to recharge the batteries use the recharge docking station mod. MSC-2.

RI-840 Wireless in ear belt-pack monitor receiver with earphones Place the receiver in the corresponding compartment in the recharge docking station MSC-2. Remove the

plastic adapter beforehand in order to insert the wireless belt-pack transmitter. During the charging process, the LED CHARGE indicator of the recharge docking station will light up permanently in red. When the charging process has ﬁnished, the LED FULL indicator will light up green.

MSHT-40M Wireless hand-held transmitter microphone Place the microphone in the compartment designed for it in the recharge docking station MSC-2. During the

charging process, the LED CHARGE indicator of the recharge docking station will light up permanently in red. When the charging process has ﬁnished, the LED FULL indicator will light up in green.

MSHT-45P Tie-clip microphone with wireless belt-pack transmitter Place the microphone in the corresponding compartment in the recharge docking station MSC-2. Remove

the plastic adapter beforehand in order to insert the wireless belt-pack transmitter. During the charging process, the LED CHARGE indicator of the recharge docking station will light up permanently in red. When the charging process has ﬁnished, the LED FULL indicator will light up green.

Page 10

TROUBLE-SHOOTING

TECHNICAL SPECIFICATIONS

PROBLEM SOLUTION

There is no sound - Check the transmitter’s and receiver’s power supply.

- Check that the transmitter and the receiver are tuned to the same frequency/channel.

- Check if the transmitter is very far away from the receiver.

- Check if the receiver is situated near metal objects or if there are obstacles between the receiver and the transmitter.

Interference - When using 2 or more transmitters simultaneously check that the selected

channels do not interfere.

- Check if the interference is coming from another wireless microphone system, TV, radio, etc.

Distortion - Check if the receiver volume is selected very low or very high.

- Check if the interference is coming from another wireless microphone system, TV, radio, etc.

RI-840

CHARACTERISTICS Wireless in ear belt-pack monitor receiver with 40 selectable PLL UHF

863-865 MHz channels. Reception with mono FM modulation. For use with the FONESTAR wireless in ear monitor system. Several receivers (RI-840) can be used in the same channel with one transmitter. For use with models MSHT-40M-863, MSHT-41P-863, MSHT-42S-863, MSHT-43C-863, MSHT-44X-863 and MSHT-45P-863.

OUTPUTS Headphone, 3.5 mm stereo jack RESPONSE 50-15,000 Hz CONTROLS On/off

Volume control Single (L) or double (L+R) output selector Conﬁguration buttons and RF channel selection

POWER SUPPLY 2 x LR6-AA batteries. Accepts rechargeable batteries; integrated recharge

function

DIMENSIONS 64 x 108 x 24 mm depth ACCESSORIES Silicone earphones

Belt clip Rechargeable batteries

OPTIONAL MSC-2, MSC-12 and MSC-24: wireless microphone recharge docking

stations

- 10 -

Page 11

MRI-844 (transmitter: MSHT-40M + receiver: RI-840)

Personal in ear monitor system for audio signal transmission in the UHF 863-865 MHz band. Composed of a wireless hand-held microphone transmitter (MSHT-40M) and a wireless in ear monitor beltp

ack receiver (RI-840) with silicone rubber earphones. 40 selectable PLL UHF 863-865 MHz channels.

Possibility of using multiple receivers (RI-840) in the same channel with one transmitter.

TPRI-845 (transmitter: MSHT-45P + receiver: RI-840)

Personal in ear monitor system or audio signal transmission in the UHF 863-865 MHz band. Composed of a tie-clip microphone with belt-pack transmitter (MSHT-45P) and a wireless in ear belt-pack monitor receiver (RI-840) with silicone earphones. 40 selectable PLL UHF 863-865 MHz channels. Mono FM modulation. Possibility of using multiple receivers (RI-840) in the same channel with one transmitter.

MSHT-40M

CHARACTERISTICS Wireless hand-held microphone with unidirectional electret condenser

capsule and UHF transmitter for replacement or extension. 863-865 MHz 40 channels 823-832 MHz 32 channels 512-525 MHz 32 channels For models MSH-887, MSH-895 and MSH-898.

POWER SUPPLY 2 LR6-AA batteries. Accepts rechargeable batteries; integrated recharge

function

DIMENSIONS 257 x 52 mm Ø

ACCESSORIES

Rechargeable batteries

OPTIONAL MSC-2, MSC-12 and MSC-24: wireless microphone docking stations

MSHT-45P

CHARACTERISTICS Tie-clip microphone with unidirectional electret condenser capsule and

UHF wireless belt-pack transmitter for replacement or extension. Hand-held microphone with unidirectional electret condenser capsule and UHF transmitter for replacement or extension. 863-865 MHz 40 channels 823-832 MHz 32 channels 512-525 MHz 32 channels For models MSH-883, MSH-892 and MSH-898.

POWER SUPPY 2 x LR6-AA batteries. Accepts rechargeable batteries; integrated

recharge function

DIMENSIONS 64 x 108 x 24 mm depth

ACCESSORIES

Windshield Tie-clip Rechargeble batteries

OPTIONAL

MSC-2, MSC-112 and MSC-24: wireless microphone recharge docking

stations

- 11 -

Page 12

SRI-841 (transmitter: TSI-40 + receiver: RI-840)

Wireless personal monitor diversity system for audio signal transmission in the UHF 863-865 MHz band. C

omposed of a transmitter for desktops or for installing in a 1 U 19" rack (TSI-40) and a wireless in ear

monitor belt-pack receiver (RI-840) with silicone earphones. 4

0 selectable PLL UHF 863-865 MHz channels. FM modulation.

Possibility of using as many receivers (RI-840) as required in one channel with each transmitter.

TSI-40

DESCRIPTION UHF transmitter for desktop or installing in 1 U 19" rack.

40 selectable PLL UHF 863-865 MHz channels. Transmission with mono FM modulation. For use with the FONESTAR wireless monitor in ear system.

INPUTS 2 mic./L and R line, 6.3 mm jack

1 aux, 3.5 mm stereo jack

OUTPUTS Stereo headphone, 3.5 mm jack CONTROLS On/off

Volume controls: L and R channel and headphone output Conﬁguration and RF channel selection buttons RF output level control

POWER SUPPLY 12 V DC, 450 mA with adapter included DIMENSIONS 210 x 46 x 215 mm depth ACCESSORIES Antenna, 1 m cable with 6.3 mm mono jack connector and mounts for

assembly in 1 U 19" rack

- 12 -

Page 13

DECLARATION OF CONFORMITY

FONESTAR SISTEMAS S.A.

Polígono de Trascueto s/n 39600 Revilla de Camargo, Cantabria (España)

eclares, under its responsibility, that the following equipment:

escription: Wireless UHF personal in ear monitor systems Brand: FONESTAR Models: TMRI-844, TPRI-845

comply with that shown in theEuropean Parliament and Council directive 1999/5/EC of 9th March 1999, transposed to Spanish legislation through the Real Decreto 1890/2000, on 20th November.

This is class 1 equipment and has no use restrictions.

List of standards applied

Standard Area Compliance with he 1999/5/EC essential

directive requirements

EN 300 422-2 RADIO Section 3.2 1999/5/EC directive

Revilla de Camargo, 5th September, 2014

uan Vallejo

echnical Engineer, Sales departmentl

- 13 -

Page 14

WARRANTY

This product has been tested and has passed the corresponding quality control prior to being put on the market. FONESTAR guarantees the suitability of the product for its speciﬁed use during a period of 2 years from the

delivery date and commits itself to repair or substitute the goods as expressed in the Spanish law ‘La Ley General para la Defensa de los Consumidores y Usuarios, Real Decreto Legislativo 1/2007 16 Noviembre.

The lack of conformity in the ﬁrst six months after purchase, due to a manufacturing defect, will be rectiﬁed with no more than showing the proof of purchase. After six months FONESTAR reserves the right to demand proof of the product being sold with that problem.

This warranty does not include damage produced by: inappropriate use or negligence, accidents, worn out parts due to use, breakages, burns, spilt liquids or other substances, excessive humidity, battery deterioration and internal manipulation of the device, the software or its components by unauthorized persons, and in general any use that is unrelated to the nature and purpose of the product.

If any service is needed during the warranty period because of lack of conformity, please contact the business or distributor where the product was purchased in no more than 2 months after being conscious of the problem. It is only necessary to contact FONESTAR if it is impossible or imposes an undue burden for them to solve it.

To beneﬁt from this warranty it is necessary to show the proof of purchase with the date clearly visible, with no corrections or crossing out.

This document adds information, and never decreases the consumers’ rights, which in all cases are protected by the Spanish law ‘La Ley General para la Defensa de los Consumidores y Usuarios, Real Decreto Legislativo 1/2007 16 Noviembre.

- 14 -

FONESTAR is a member of ECOEMBALAJES ESPAÑA, S.A. “ECOEMBES”, with number 03497 and all our products carry the symbol, backed by our membership and subscription to the above mentioned organization with the recycling and subsequent management of our packaging.

FONESTAR, S.A. - NIF: A28780443 - Polígono Trascueto - 39600 Revilla de Camargo, Cantabria (Spain)

www.fonestar.com

Page 15

- 15 -

Page 16

www.fonestar.com

FONESTAR TMRI-844, TPRI-845, TSRI-841 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual