FONESTAR TMRI-844, TPRI-845, TSRI-841 Instruction Manual

TMRI-844, TPRI-845, TSRI-841

WIRELESS PERSONAL MONITOR SYSTEM

40 PLL UHF 863-865 MHz CHANNELS

INSTRUCTION MANUAL

RI-840

MSHT-45P

MSHT-40M

TSI-40

EN

- 2-

W

e take this opportunity to thank you for buying this product.

We recommend you read the instruction manual before switching on the machine and follow the instructions
t

hat are given. Keep the manual for future reference.

SECURITY AND THE ENVIRONMENT

ELECTRICAL SECURITY
Check that the current in the mains connection where the machine is to be installed corresponds to the
power supply of the machine.
To avoid damaging the equipment, electrical shocks, fire or physical injury when you connect or disconnect
the equipment from the power supply, pull the plug firmly out of the mains socket holding the plug, never the
cable.
Always do this with dry hands.
Keep the power supply cable far from sources of heat. Do not put heavy objects on top of it or change it.
Clean dust and dirt off the power supply cable regularly.
Do not open the machine; you could get an electric shock.

CAUTION
While installing the machine, make sure it is switched off and unplugged.
Do not open the machine. Touching the internal parts is dangerous and you could receive an electric shock.
The machine must not be splashed or dripped on. Never place recipients with liquid inside on the machine.
Do not place anything inside the machine.

LOCATION
Place the equipment on a horizontal surface with enough space around it to allow ventilation.
Avoid direct sunlight, heat sources and excessive dust.
Do not place the machine near magnetic fields or static electricity.
Do not use surfaces which vibrate or receive impact.
Do not pile machines on top of one another.

VENTILATION
Never block or cover the ventilation slits on the machine.
Do not expose it to direct sunlight or place it near sources of heat.

PERIODS OF INACTIVITY
When the machine is not going to be used for a long period of time, disconnect it from the mains.
If you are using an adapter, take into account that it will continue using electricity even if the machine is
switched off. If it is not going to be used for a long period of time, disconnect it from the mains.

THE ENVIRONMENT
To save energy, switch the machine off when you are not going to use it for a long time. The machine could
contain substances that are harmful to the environment or human health. To minimize the effect of these
substances the machine must be correctly managed and recycled when you decide to dispose of it.
When you dispose of it remember: it cannot be thrown into a conventional rubbish bin.
If it contains or uses batteries, these must be disposed of separately.
The machine (without batteries) must be disposed of correctly. Put it in a container specially intended for the
collection of electronic and electrical appliances, at the dump or hand it over to the dealer when you purchase
similar equipment, so that the dealer can dispose of it correctly (at no added cost).

SIGNIFICANCE OF THE SYMBOLS ON THE MACHINE*

The symbol formed by the expression “Class 1 laser product” written in a rectangle
indicates that visible or invisible laser radiation could be produced. Avoid direct expose to
the laser.

The symbol formed by a ray of lightening inside a triangle shows that the machine has
connection terminals or a circuit with areas with a current which could cause an electric
s

hock, even in normal working conditions.

The symbol formed by an exclamation mark in a triangle shows that the instruction manual
must be referred to for information on how the machine works and its use.

The symbol formed by one square inside another square shows that the machine has
double electrical insulation.

The European Community symbol shows that the machine complies with the current
European Union legislation, as well as its transposition to local legislation.

The symbol of a rubbish bin crossed out and over a horizontal line shows that when the
product is disposed of it must be done properly, placing it in a special selective electronic
and electrical equipment container or through a dealer when purchasing a similar product,
at no additional cost. It also shows that the machine was put on the market after 13th
August 2005 (European Community Directive 2002/96/CE of Electrical and Electronic
recycling, and its Spanish equivalent R.D.208/2005).

In accordance with what is set out in the aforementioned decree, FONESTAR is registered
in the RAEE (Registro de Aparatos Eléctricos y Electrónicos) in a special section REI
(Registro de establecimientos Industriales), with the entry number 001851.

*It is possible that some of these symbols do not appear on the machine.

EXEMPTION OF LIABILITY

The characteristics of the equipment and the content of the manual can change without forewarning.
FONESTAR, S.A. does not assume responsibilities regarding the inappropriate use of the equipment or the
information supplied in this instruction manual, and specifically disclaims any implied liability for marketability
or fitness for any other use.

All rights reserved by FONESTAR, S.A.

- 3-

EN

DESCRIPTION

W

ireless personal monitor system for audio signal transmission in the band UHF 863-865 MHz. The system is
composed of a wireless in ear belt-pack monitor receiver (mod. RI-840) with silicone rubber earphones and
a

wireless hand-held microphone transmitter (mod. MSHT-40M) or a tie-clip microphone (mod. MSHT-45P)

w

ith wireless belt-pack transmitter, depending on the model chosen.

The system has 40 transmission channels in the band UHF 863-865 MHz, with PLL frequency control which
a

llows a transmission channel free of interference to be easily selected.

I

t is possible to use multiple receivers (RI-840) in the same channel with one transmitter.

CONTROLS AND FUNCTIONS

RI-840 Wireless in ear belt-pack monitor receiver with headphones.

1.- Information display: displays information on tuned frequency, channel number, battery level, RF signal

level and audio signal level. If the level of the batteries is low, the display will light up red.

2.- w/s: allow menu options to be selected in order to configure the wireless belt-pack receiver.

3.- SET: allows selection among the different configuration options: channel number and frequency, RF

transmission level (high/low), battery type selection (1.2 V - rechargeable/1.5 V - alkaline) to display the
battery level correctly and lock the receiver. In order to do so, press the SET button repeatedly and use
the w/s buttons to select the options.

4.- Battery compartment: uses two 1.5 V LR6-AA batteries, alkaline or rechargeable.When inserting the

batteries, make sure the polarity is correct.

5.- HEADPHONES OUTPUT: select the type of headphone output signal, single (L+R channels in left earphone)

or double (L+R channels in both earphones).

6.- Contacts to recharge the rechargeable batteries of the wireless receiver in the recharge docking station mod.

MSC-2.

7.- Antenna.

8.- VOL: wireless belt-pack receiver volume control.

9.- 3.5 mm stereo jack connector for connecting headphones/recording. If you wish to record a signal

received by the receiver RI-840, connect the recording equipment to the headphone output or use an
adapter to be able to use the headphone signal and the recorder simultaneously.

10.- POWER: receiver on/off switch.

Note: when the SET button is pressed to configure the different parameters of the receiver, a MUTE indicator

appears in the display and the receiver will not receive audio while the parameters are being
configured.

- 4-

EN

M

SHT-40M Wireless hand-held microphone transmitter

1.- Grille: protects the microphone capsule and helps to reduce noises from breathing or the wind blowing.

2.- Display: displays information on the tuned frequency, channel number, battery level, RF signal level
and audio signal level. If the battery level is low, the screen will light up red.

3.- Battery compartment: unscrew this cover to access the battery compartment.

4.- GAIN: adjust the sensibility of the audio input.

5.-

q

: hand-held microphone on/off switch.

6.- Battery compartment: use two 1.5 V LR6-AA type batteries, alkaline or rechargeable. When inserting
the batteries, make sure that the polarity is correct.

7.- SET: allows selection among the following configuration options: channel number and frequency, RF
transmission level (high/low), battery type selection (1.2 V - rechargeable/1.5 V - alkaline) to display the
battery level correctly and lock the microphone transmitter. In order to do so, press the SET button
repeatedly and use the w/s buttons to select the options.

8.- w/s: allow selection of the menu options to configure the hand-held wireless microphone.

9.- Contacts to recharge the wireless microphone’s rechargeable batteries in the recharge docking station
mod. MSC-2.

Note: when the SET button is pressed to configure the different microphone parameters, a MUTE indicator

appears in the display and the microphone does not transmit audio while the parameters are being
configured.

- 5-

EN