Page 1
FMC-640 / FMC-641 / FMC-643
MICROPHONES WITH HEADSET FOR
TELEPHONE USE
EN Instruction manual
FMC-640 FMC-643FMC-641
Page 2
EN
We take this opportunity to thank you for buying this product.
We recommend you read the instruction manual before switching on the machine and follow the instructions
that are given. Keep the manual for future reference.
SECURITY AND THE ENVIRONMENT
ELECTRICAL SECURITY
Check that the current in the mains connection where the machine is to be installed corresponds to the
power supply of the machine.
To avoid damaging the equipment, electrical shocks, fire or physical injury when you connect or disconnect
the equipment from the power supply, pull the plug firmly out of the mains socket holding the plug, never the
cable.
Always do this with dry hands.
Keep the power supply cable far from sources of heat. Do not put heavy objects on top of it or change it.
Clean dust and dirt off the power supply cable regularly.
Do not open the machine; you could get an electric shock.
CAUTION
While installing the machine, make sure it is switched off and unplugged.
Do not open the machine. Touching the internal parts is dangerous and you could receive an electric shock.
The machine must not be splashed or dripped on. Never place recipients with liquid inside on the machine.
Do not place anything inside the machine.
LOCATION
Place the equipment on a horizontal surface with enough space around it to allow ventilation.
Avoid direct sunlight, heat sources and excessive dust.
Do not place the machine near magnetic fields or static electricity.
Do not use surfaces which vibrate or receive impact.
Do not pile machines on top of one another.
VENTILATION
Never block or cover the ventilation slits on the machine.
Do not expose it to direct sunlight or place it near sources of heat.
PERIODS OF INACTIVITY
When the machine is not going to be used for a long period of time, disconnect it from the mains.
If you are using an adapter, take into account that it will continue using electricity even if the machine is
switched off. If it is not going to be used for a long period of time, disconnect it from the mains.
THE ENVIRONMENT
To save energy, switch the machine off when you are not going to use it for a long time. The machine could
contain substances that are harmful to the environment or human health. To minimize the effect of these
substances the machine must be correctly managed and recycled when you decide to dispose of it.
When you dispose of it remember: it cannot be thrown into a conventional rubbish bin.
If it contains or uses batteries, these must be disposed of separately.
The machine (without batteries) must be disposed of correctly. Put it in a container specially intended for the
collection of electronic and electrical appliances, at the dump or hand it over to the dealer when you purchase
similar equipment, so that the dealer can dispose of it correctly (at no added cost).
- 2-
Page 3
SIGNIFICANCE OF THE SYMBOLS ON THE MACHINE*
The symbol formed by the expression “Class 1 laser product” written in a rectangle
indicates that visible or invisible laser radiation could be produced. Avoid direct exposure
to the laser.
The symbol formed by a ray of lightening inside a triangle shows that the machine has
connection terminals or a circuit with areas with a current which could cause an electric
shock, even in normal working conditions.
The symbol formed by an exclamation mark in a triangle shows that the instruction manual
must be referred to for information on how the machine works and its use.
The symbol formed by one square inside another square shows that the machine has
double electrical insulation.
The European Community symbol shows that the machine complies with the current
European Union legislation, as well as its transposition to local legislation.
The symbol of a rubbish bin crossed out and over a horizontal line shows that when the
product is disposed of it must be done properly, placing it in a special selective electronic
and electrical equipment container or through a dealer when purchasing a similar product,
at no additional cost. It also shows that the machine was put on the market after 13th
August 2005 (European Community Directive 2002/96/CE of Electrical and Electronic
recycling, and its Spanish equivalent R.D.208/2005).
EN
In accordance with what is set out in the aforementioned decree, FONESTAR is registered
in the RAEE (Registro de Aparatos Eléctricos y Electrónicos) in a special section REI
(Registro de establecimientos Industriales), with the entry number 001851.
The symbol RoHS (Restriction of Hazardous Substances) shows that the product has been
designed and manufactured restricting the use of certain dangerous material(Directive
2002/95/CE on the restriction of certain dangerous substances in electrical and electronic
appliances, and its transferal to the Spanish regulations, R.D. 208/2005).
*It is possible that some of these symbols do not appear on the machine.
EXEMPTION OF LIABILITY
The characteristics of the equipment and the content of the manual can change without forewarning.
FONESTAR, S.A. does not assume responsibilities regarding the inappropriate use of the equipment or the
information supplied in this instruction manual, and specifically disclaims any implied liability for marketability
or fitness for any other use.
All rights reserved by FONESTAR, S.A.
- 3-
Page 4
EN
DESCRIPTION
Microphones with headset for telephone use, with a multiconfiguration module for different telephone
systems.
Mute function and choosing between microphone-headset and telephone available.
Cable with quick disconnection and clip incorporated.
They are light and suitable for use in different telephone system applications: telemarketing, secretarial,
technical services, etc.
Compatible with almost all telephone and switchboard operator jobs, as well as other intercom, call and
computer systems.
CONTROLS AND FUNCTIONS
1.- : Microphone selector with headset or telephone.
2. Lid.
3. 1, 2, 3, 4: Setup selector.
4. Connection for the microphone with headset.
5. A, B, C: Setup selector.
6. MUTE/TALK: Mute or talk button for the microphone.
7. Connector cable going to the telephone receiver.
8. Connection for the telephone headset.
CONNECTION
Connect the microphone with headset to the multiconfiguration module and this to the telephone receiver
connector, which at the same time is connected to the multiconfiguration module.
- 4-
Page 5
EN
INSTRUCTIONS FOR USE
The multiconfiguration module does not need batteries.
Before starting, put on the microphone with headset.
Regulate the position of the tube until the microphone is 5 cm (approx.) from your mouth and speak normally
into the microphone, to not saturate the signal. Turn the microphone gently and handle the cable and the
connectors carefully to avoid breakages. Do not apply excessive power to the headset, to avoid damaging
them.
Then pick up the telephone or press the corresponding button on the telephone to get a line. Check that
the button marked with a microphone with headset and a telephone is pressed down (the microphone
with headset position has been selected) and the MUTE/TALK button is not pressed down (the TALK
position has been selected).
The mic. with headset and telephone button lets you choose between using the microphone with headset
or the telephone receiver. When the button has been pressed down communication is made through the
microphone with the headset. With the button released, you can use the telephone receiver.
If you press the MUTE/TALK button the person on the other end of the line cannot hear, but you can hear
them. To continue with the conversation, press the button again to release it and select the TALK position.
CONFIGURATION SELECTION
Open the top lid of the multiconfiguration module. There are 2 selector switches marked 1, 2, 3, 4 and A, B,
C, D. With these selectors you can get 12 setups which provide a high possibility of compatibility. Test the
positions one by one until you can hear a clear ring tone through the mic. headset.
Take into account that there could be various setups giving a ring tone. Just choose the one which sounds
the best. There is at least one setting which fits your telephone.
.
- 5-
Page 6
EN
SPECIFICATIONS
FMC-640 FMC-641 FMC-643
Headset Mono headset
RESPONSE 100-5000 Hz 300-4000 Hz
SENSITIVITY 105 dB at 1 kHz ±3 dB 101 dB at 1 kHz ±3 dB 105 dB at 1 kHz ±3 dB
IMPEDANCE 150 Ω
POWER 30 mW maximum
SPEAKER 27 mm Mylar 40 mm Mylar 28 mm Mylar
PAD Synthetic leather Foam
ACCESSORIES - - Synthetic leather pad
Microphone
CAPSULE Omnidirectional electret
condenser
RESPONSE 40-16 000 Hz
SENSITIVITY -44 dB (V/Pa) -38 dB (V/Pa)
IMPEDANCE 1000 Ω 2200 Ω
MIC. SUPPORT Transparent extendable
tube, turns in all
directions
CONNECTOR 4-contact modular
CABLE 1.5 m extendable up to 3 m approx., with quick disconnection and clip
WEIGHT 0.1 kg
ACCESSORIES Multiconfiguration module for using with different telephone systems, mute function
and choice between microphone-headset or telephone
- Windshield
Noise cancelling electret condenser
Flexible tube with 270° rotation
- 6-
- 6-
Page 7
DECLARATION OF CONFORMITY
The FMC-640, FMC-641 and FMC-643 microphones with headset for telephone use comply with the
European Community Directives 2004/108/EC on Electromagnetic Compatibility.
Santander, 21st January 2011
Juan Vallejo
Technical Engineer, Sales Department
EN
WARRANTY
This product has been tested and has passed the corresponding quality control prior to being put on the market.
FONESTAR guarantees the suitability of the product for its specified use during a period of 2 years from the delivery date
and commits itself to repair or substitute the goods as expressed in the Spanish law ‘La Ley General para la Defensa de los
Consumidores y Usuarios, Real Decreto Legislativo 1/2007 16 Noviembre.
The lack of conformity in the first six months after purchase, due to a manufacturing defect, will be rectified with no more
than showing the proof of purchase. After six months FONESTAR reserves the right to demand proof of the product being
sold with that problem.
This warranty does not include damage produced by: inappropriate use or negligence, accidents, worn out parts due to use,
breakages, burns, spilt liquids or other substances, excessive humidity, battery deterioration and internal manipulation of the
device, the software or its components by unauthorized persons, and in general any use that is unrelated to the nature and
purpose of the product.
If any service is needed during the warranty period because of lack of conformity, please contact the business or distributor
where the product was purchased in no more than 2 months after being conscious of the problem. It is only necessary to
contact FONESTAR if it is impossible or imposes an undue burden for them to solve it.
To benefit from this warranty it is necessary to show the proof of purchase with the date clearly visible, with no corrections or
crossing out.
This document adds information, and never decreases the consumers’ rights, which in all cases are protected by the Spanish
law ‘La Ley General para la Defensa de los Consumidores y Usuarios, Real Decreto Legislativo 1/2007 16 Noviembre’.
FONESTAR
symbol, backed by our membership and subscription to the above mentioned organization with the recycling and subsequent
management of our packaging.
FONESTAR S.A. - NIF A28780443 - Apartado 191 - 39080 - Santander, Cantabria, (España)
www.fonestar.com
is a member of ECOEMBALAJES ESPAÑA, S.A. “ECOEMBES”, with number 03497 and all our products carry the
- 7-
- 7-
Loading...