ASB-880U, ASB-10120U
SB-3608, SB-3611
LOUDSPEAKER
INSTRUCTION MANUAL
We take this opportunity to thank you for buying this product.
W
e recommend you read the instruction manual before switching on the machine and follow the instructions
that are given. Keep the manual for future reference.
SECURITY AND THE ENVIRONMENT
ELECTRICAL SECURITY
C
heck that the current in the mains connection where the machine is to be installed corresponds to the
power supply of the machine.
To avoid damaging the equipment, electrical shocks, fire or physical injury when you connect or disconnect
the equipment from the power supply, pull the plug firmly out of the mains socket holding the plug, never the
cable.
Always do this with dry hands.
Keep the power supply cable far from sources of heat. Do not put heavy objects on top of it or change it.
Clean dust and dirt off the power supply cable regularly.
Do not open the machine; you could get an electric shock.
CAUTION
While installing the machine, make sure it is switched off and unplugged.
Do not open the machine. Touching the internal parts is dangerous and you could receive an electric shock.
The machine must not be splashed or dripped on. Never place recipients with liquid inside on the machine.
Do not place anything inside the machine.
LOCATION
Place the equipment on a horizontal surface with enough space around it to allow ventilation.
Avoid direct sunlight, heat sources and excessive dust.
Do not place the machine near magnetic fields or static electricity.
Do not use surfaces which vibrate or receive impact.
Do not pile machines on top of one another.
VENTILATION
Never block or cover the ventilation slits on the machine.
Do not expose it to direct sunlight or place it near sources of heat.
PERIODS OF INACTIVITY
When the machine is not going to be used for a long period of time, disconnect it from the mains.
If you are using an adapter, take into account that it will continue using electricity even if the machine is
switched off. If it is not going to be used for a long period of time, disconnect it from the mains.
THE ENVIRONMENT
To save energy, switch the machine off when you are not going to use it for a long time. The machine could
contain substances that are harmful to the environment or human health. To minimize the effect of these
substances the machine must be correctly managed and recycled when you decide to dispose of it.
When you dispose of it remember: it cannot be thrown into a conventional rubbish bin.
If it contains or uses batteries, these must be disposed of separately.
The machine (without batteries) must be disposed of correctly. Put it in a container specially intended for the
collection of electronic and electrical appliances, at the dump or hand it over to the dealer when you purchase
similar equipment, so that the dealer can dispose of it correctly (at no added cost).
- 2-
E
N
SIGNIFICANCE OF THE SYMBOLS ON THE MACHINE*
The symbol formed by the expression “Class 1 laser product” written in a rectangle
indicates that visible or invisible laser radiation could be produced. Avoid direct expose to
the laser.
The symbol formed by a ray of lightening inside a triangle shows that the machine has
c
onnection terminals or a circuit with areas with a current which could cause an electric
shock, even in normal working conditions.
The symbol formed by an exclamation mark in a triangle shows that the instruction manual
must be referred to for information on how the machine works and its use.
The symbol formed by one square inside another square shows that the machine has
double electrical insulation.
The European Community symbol shows that the machine complies with the current
European Union legislation, as well as its transposition to local legislation.
The symbol of a rubbish bin crossed out and over a horizontal line shows that when the
product is disposed of it must be done properly, placing it in a special selective electronic
and electrical equipment container or through a dealer when purchasing a similar product,
at no additional cost. It also shows that the machine was put on the market after 13th
August 2005 (European Community Directive 2002/96/CE of Electrical and Electronic
recycling, and its Spanish equivalent R.D.208/2005).
In accordance with what is set out in the aforementioned decree, FONESTAR is registered
in the RAEE (Registro de Aparatos Eléctricos y Electrónicos) in a special section REI
(Registro de establecimientos Industriales), with the entry number 001851.
*It is possible that some of these symbols do not appear on the machine.
EXEMPTION OF LIABILITY
The characteristics of the equipment and the content of the manual can change without forewarning.
FONESTAR, S.A. does not assume responsibilities regarding the inappropriate use of the equipment or the
information supplied in this instruction manual, and specifically disclaims any implied liability for marketability
or fitness for any other use.
All rights reserved by FONESTAR, S.A.
- 3-
E
N
DESCRIPTION
THIS MANUAL CORRESPONDS TO THE FOLLOWING MODELS:
ASB-880U, ASB-10120U
- Biamplified loudspeaker with extra-resistant PP injection-moulded case.
- USB/SD/MP3 player with remote control.
- Output for passive loudspeaker.
- Woofer protected by front metal grille.
- Carrying handles, suspension points, floor supports and monitor shaped.
- Hole in the base for 35 mm tube.
SB-3608, SB-3611
- Loudspeaker with extra-resistant PP injection-moulded case.
- Woofer protected by front metal grille.
- Carrying handles, suspension points, floor supports and monitor shaped
- Hole in the base for 35 mm tube
ASB-880U, ASB-10120U
CONTROLS AND FUNCTIONS
- 4-
E
N
1.- USB/SD/MP3 player module.
1.- LED: USB/SD/MP3 module power indicator.
It lights up red when the loudspeaker is switched on. It flashes when the USB storage device or
the SD memory card are connected and the music is playing. To stop the USB/SD/MP3 module,
use the stop button on the remote control (this indicator will switch off).
2.- EQ: allows selection of the different equalizations.
3.- 8: a short press of this button forwards to the next track. A long press increases the volume of
playback.
4.- 12: to start and pause playback.
5.- 7: a short press of this button rewinds to the previous track. A long press reduces the volume of
the playback.
6.- INPUT: allows selection between the USB storage device and the SD memory card.
7- USB: USB storage device connection slot.
8.- SD: SD memory card connection slo0t.
9.- IR receiver for the remote control.
2.- MP3 VOL: USB/SD/MP3 player module general volume control
3.- MIC INPUT: microphone balanced input, XLR connectors and 6.3 mm jack.
4.- MIC VOL: microphone input volume control.
5.- LINE INPUT: line level auxiliary input, XLR connectors and 2 x RCA.
6.- LINE VOL: line input volume control.
7.- LINE OUT: line level balanced output, 6.3 mm jack connector.
8.- SPEAKER OUTPUT: amplified output for connecting to the passive loudspeaker, loudspeaker
connector 8 Ω.
9.- MASTER: general volume control.
10.- TREBLE/BASS: tone controls. Equalizer that adjusts the levels treble and bass. Gain controls of ±12 dB.
11.- POWER: LED power indicator for loudspeaker.
12.- CLIP: LED excess signal indicator. It lights up red when an input level is detected with a level that is too
high or when there is an excessive output level which could cause damage.
13.- AC SELECT: power supply voltage selector 115/230 V AC.
Note: in the model ASB-880U this selector is internal.
14.- POWER: on/off switch for the loudspeaker.
15.- AC socket. To connect the mains cable.
- 5-
E
N
E
N
- 6-
REMOTE CONTROL
1.- STOP: on/off button for the USB/SD/MP3 player.
2.- MODE: allows selection of the audio source between the USB storage
d
evice or the SD memory card.
3.- MUTE: activates/deactivates the audio output.
4
.- 7/8: allows selection of the previous/next audio track on the
USB/SD/MP3 player.
5.-
12
: to start and pause playback.
6.- +/-: controls the volume of the USB/SD/MP3 player.
7.- EQ: allows selection among the different equalizations that exist.
8.- 100+, 200+: allows the audio track number that is playing at that
moment to be increased by 100 or 200
9.- 0-9: numerical buttons to automatically select the audio track required.
CONNECTION
- Before connecting the power supply, make sure that the volume controls are at their minimum and the
POWER switch is off.
- Connect the mains cable to the power supply.
- Connect a line level signal to the LINE INPUT input of the loudspeaker, for a mixer output, a CD player,
etc. A USB storage device or an SD memory card can also be connected in the corresponding ports.
- If you wish, a dynamic microphone can be connected in the MIC INPUT.
- Switch on the loudspeaker with the POWER switch on the rear panel.
- Adjust the input volume to the required level using the corresponding controls.
- The loudspeaker output provides a line level (LINE OUT output) that can be taken to another amplified
loudspeaker, mixer, amplifier, recorder, etc.
- Furthermore, if you wish, a passive loudspeaker can be connected to the SPEAKER OUTPUT terminal.
- When not using the equipment, switch it off: turn the volume controls to minimum, deactivate it with the
power switch and disconnect the power supply from the mains.
E
N
- 7-
SB-3608, SB-3611
CONTROLS AND FUNCTIONS
1- INPUT: 4-contact loudspeaker connector.
The loudspeaker line must be connected in the following way:
Terminal 1+ = positive
Terminal 1- = negative
Loudspeaker connector seen from the side of the connection terminal
2.- OUTPUT: 4-contact loudspeaker connector, to connect more biamplified loudspeakers in cascade.
TECHNICAL SPECIFICATIONS
ASB-880U ASB-10120U
CHARACTERISTICS Biamplified loudspeaker with extra-resistant, PP injection-moulded case.
U
SB/SD/MP3 player with remote control.
O
utput for passive loudspeaker.
Woofer protected by front metal grille.
Monitor shaped loudspeaker with carrying handles, suspension points and
floor supports.
Hole in the base for a 35 mm tube.
AMPLIFIER 160 W maximum, 80 W RMS
Bass: 100 W maximum, 50 W RMS
Treble: 60 W maximum, 30 W RMS
200 W maximum, 100 W RMS
Bass: 120 W maximum, 60 W RMS
Treble: 80 W maximum, 40 W RMS
PROTECTION 3 protection circuits: short circuit, overload and temperature
LOUDSPEAKERS 1 x 8” woofer
1 compression motor: 1 3/8”
diaphragm
1 x 10” woofer
1 compression motor: 1 3/8”
diaphragm
RESPONSE
60-18,000 Hz 55-18,000 Hz
INPUTS 1 balanced mic., XLR and 6.3 mm jack
1 aux line, XLR and 2 x RCA
OUTPUTS 1 aux line, 6.3 mm jack
1 amplified for passive loudspeaker, 8 Ω speaker connector
INDICATORS Power on the front and on and peak on the rear panel
CONTROLS Input volume and general volume
USB/SD/MP3 player control
Bass and treble control
SUSPENSION
POINTS
6 x M8 points
POWER SUPPLY 230 V AC, 160 W 230/115 V AC, 240 W
DIMENSIONS 260 x 420 x 230 mm depth 320 x 515 x 270 mm depth
- 8-
E
N
S
B-3608
S
B-3611
CHARACTERISTICS Loudspeaker with extra-resistant, PP injection-moulded case.
Woofer protected by front metal grille.
Monitor shaped loudspeaker with carrying handles, suspension points and
floor supports.
Hole in the base for 35 mm tube.
P
OWER
2
00 W maximum, 100 W RMS
3
00 W maximum, 150 W RMS
LOUDSPEAKERS 1 x 8” woofer
1 compression motor: 1 3/8”
diaphragm
1 x 10” woofer
1 compression motor: 1 3/8”
diaphragm
RESPONSE
60-18,000 Hz 55-18,000 Hz
IMPEDANCE
8 Ω
SENSITIVITY
96 dB at 1 W/1 m 97 dB at 1 W/1 m
CONNECTORS
2 x 4-contact loudspeaker connectors (1+, 1-)
INDICATORS
Power on the front
CROSSOVER 2 ways
Crossover frequency at 2,500 Hz
SUSPENSION
POINTS
6 x M8 points
SOUND PRESSURE 119 dB at maximum power at 1 m 121 dB at maximum power at 1 m
DIMENSIONS 260 x 420 x 230 mm depth 320 x 515 x 270 mm depth
- 9-
E
N
WARRANTY
This product has been tested and has passed the corresponding quality control prior to being put on the market.
FONESTAR guarantees the suitability of the product for its specified use during a period of 2 years from the delivery date
and commits itself to repair or substitute the goods as expressed in the Spanish law ‘La Ley General para la Defensa de los
Consumidores y Usuarios, Real Decreto Legislativo 1/2007 16 Noviembre.
The lack of conformity in the first six months after purchase, due to a manufacturing defect, will be rectified with no more
than showing the proof of purchase. After six months FONESTAR reserves the right to demand proof of the product being
sold with that problem.
This warranty does not include damage produced by: inappropriate use or negligence, accidents, worn out parts due to use,
breakages, burns, spilt liquids or other substances, excessive humidity, battery deterioration and internal manipulation of the
device, the software or its components by unauthorized persons, and in general any use that is unrelated to the nature and
purpose of the product.
If any service is needed during the warranty period because of lack of conformity, please contact the business or distributor
where the product was purchased in no more than 2 months after being conscious of the problem. It is only necessary to
contact FONESTAR if it is impossible or imposes an undue burden for them to solve it..
To benefit from this warranty it is necessary to show the proof of purchase with the date clearly visible, with no corrections
or crossing out
This document adds information, and never decreases the consumers’ rights, which in all cases are protected by the Spanish
law ‘La Ley General para la Defensa de los Consumidores y Usuarios, Real Decreto Legislativo 1/2007 16 Noviembre.
FONESTAR is a member of ECOEMBALAJES ESPAÑA, S.A. “ECOEMBES”, with number 03497 and all our products carry the symbol,
backed by our membership and subscription to the above mentioned organization with the recycling and subsequent management of
our packaging.
FONESTAR, S.A. - NIF: A28780443 - Polígono Trascueto - 39600 Revilla de Camargo, Cantabria (SPAIN)
www.fonestar.com
- 11 -
www.fonestar.com
Loading...