Foneric Electronics F2 User Manual

成型尺寸: 75x65mm
128g双铜纸，印4C，表面过光油，正反折页

F2

Smart Outlet

User
Manual

FCC Declaration

Caution:

Any Changes or modifications not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.

This device must be installed and operated with a minimum
distance of 20 cm between the radiator and user body.

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including
interference

that may cause undesired operation.

This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions:

Product Overview

popa Smart Outlet can be controlled through Wi-Fi wireless network.

You can switch on/off outlet and monitor its status wirelessly.

Wi-Fi/Power statusLED indicator1

2 Power /

Reset Button

- Quick press to switch on/off

- Press & hold for about 5 seconds to factory reset.
Note: all connection data will be cleared.

This Smart Outlet must be removed from
the app and then added back again.

(1)this device may not cause interference, and
(2)this device must accept any interference, including
interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement

LED Status Indication

Status

Search Wi-Fi
Adding a device
A device added successfully
Discovering a device
Connected to Wi-Fi (Outlet On)
Connected to Wi-Fi (Outlet Off)
Disconnected from Wi-Fi

Reset

OTA in Progress
OTA done

LED Indicator

Green blinking quickly
Green blinking slowly
Red blinking slowly 5 times
Red blinking slowly 5 times
Green staying on
Indication LED stay off
Red blinking quickly

Press & Hold for 5s,
then red blinking 1 time,
green blinking quickly

Red blinking slowly
Red blinking quickly 4 times

Easy Installation

1. Download popa APP

2. Connect your mobile device to a 2.4GHz Wi-Fi Network and
make sure it is connected to internet. The product ONLY
supports the 2.4GHz networks.

3. Factory reset the product
Follow the instructions on the user manual.

Features

Smart Controls
Works with Apple HomeKit
Works with Amazon Alexa
Works with the Google Assistant

Factory Resetting

Press & hold reset button
for about 5 seconds to
factory reset

What’s Included

Electrical Ratings

Smart AC Outlet
Input: AC120V, 60Hz

Output: AC120V, 15A Max, 1800W (Pure Resistive Load)
General use ONLY

Indoor dry location use ONLY

popa F2 Smart Outlet

User Manual

System Requirements

Mobile device running iOS12.0 or later
Existing Wi-Fi network
Stable Internet with good signal strength

4. Launch popa, tap “Add Device” on Home Screen, and follow

the in-app instructions to connect the product to your network.

Safety Warnings

Plug directly into electric outlet (not into extension cord)
For indoor use only
Unplug from outlet before cleaning
DO NOT clean with liquid
DO NOT remove ground pin (round pin) as there is risk of electric shock
DO NOT use in wet or damp areas
Keep children away from Smart Outlet
DO NOT exceed the recommended electrical ratings
DO NOT use in precision timing applications where inaccurate timing
could be dangerous (sunlamps, saunas, etc.)
DO NOT use with devices that should not be operated unattendedly
After switching off the the main power, DO NOT operate until the main
power indicator goes completely off (about 2 seconds delay)
DO NOT use the device when the casing is broken

3rd Party Connections

To setup Alexa or Google Assistant, go to “User”, look for 3rd Party
Connection and follow the in-app instructions.

Setup code

Failed to control the device/lost connection?

• Make sure your mobile device and the product are connected
to the same network.

• Check your network connectivity.

• Check for signal strength on

• Factory reset the product and try to add it again.

popa app.

Support:

If you encounter any issues during installation, please simply
contact [e-mail]
We will make things right for you within 48 hours.