Foma P905i User Manual

Download

Manual for

Easy Search/

Contents/Precautions

Before Using the Handset

Voice/Videophone Calls

PushTalk

Phonebook

Sound/Screen/Light Settings

Security Settings

Camera

Mail

i-αppli

GPS Function

Osaifu-Keitai/ToruCa

Character Entry

i-mode/i-motion/

i-Channel

Full Browser

Data Display/Edit/Management

Music Playback

Other Convenient Functions

Network Services

Data Communication

Overseas Use

Appendix/External Devices/

Troubleshooting

Index/Quick Manual

’07.10

Before using your FOMA phone

You can download the latest information about this manual from the following DoCoMo web site:

・User’s Manual (PDF file) Download (http://www.nttdocomo.co.jp/english/support/manual/index.html)

※The URL and the content of the web site might be modified without notice.

DoCoMo W-CDMA system

Thank you for selecting the “FOMA P905i”.

Before or during use of the FOMA P905i, make sure that you read this manual and the separate manuals such as for the battery pack thoroughly so that you can use the FOMA P905i correctly. If you feel any inconvenience in reading the manual, contact the DoCoMo Information Center listed on the back page of this manual. The FOMA P905i is designed to be your close partner. Treat it carefully at all times to ensure long-term performance.

●

Because the FOMA phones use radio waves, they cannot be used in places where radio waves do not reach, such as inside tunnels, underground, or in buildings; or the outside where radio waves are weak or out of the FOMA service area. They may not be used in the high-rise buildings even when the antennas are unobstructed. You may also experience interruption of calls even when using without moving while the radio waves are strong enough for the three antennas to appear on the display.

●

Use the FOMA phone carefully to avoid disturbing other people when in public, or in crowded or quiet places.

●

Since the FOMA phones use radio waves as the medium of telecommunication, calls may be tapped by the third party. However, the W-CDMA system automatically supports tapping prevention, so your conversation will be incomprehensible to the third party.

●

The FOMA phones change your voice into digital signals and send them to the other party. In places where the radio waves are weak, the digital signals may not be converted correctly, and in such a case, the voice may sound different from the actual original voice.

●

It is recommended that you make separate notes of the information stored in the FOMA phone and keep such notes in a safe place. DoCoMo cannot be held responsible in any way for the loss of data stored in the phone.

●

The user hereby agrees that the user shall be solely responsible for the result of the use of SSL. Neither DoCoMo nor the certifiers as listed herein make any representation and warranty as for the security in the use of SSL. In the event that the user shall sustain damage or loss due to the use of SSL, neither DoCoMo nor the certifiers shall be responsible for any such damage or loss. Certifiers: VeriSign Japan K.K., Cybertrust, Inc., GeoTrust Japan, Inc., RSA Security Inc.,

and SECOM Trust Systems Co., Ltd.

●

This FOMA phone supports FOMA Plus-Area.

●

The

FOMA phone can be used only via the FOMA network provided by DoCoMo and in DoCoMo’s roaming area.

If this is the first time for you to use the FOMA phone, read this manual in the order as described below. Then you will get acquainted with the outline of preparing and operating procedures for using your FOMA phone.

1. Check “Safety Precautions” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P.12

2. Attach and then charge the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P.41

3. Turn on the power, set the initial settings, and check your phone number . . . . . . . . . . . . . . P.45

4. Check the keys on the FOMA phone for their roles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P.24

5. Check the meanings of icons that appear on the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P.26

6. Learn how to operate the menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P.31

7. Get well acquainted how to make and receive calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P.52

For those who use the FOMA phone for the first time

Easy Search/Contents/Precautions

In this manual, illustrations and symbols are used in the explanations so that you can easily understand how to use the FOMA phone correctly.

The operating procedures and displays in this manual are described with the default settings of the “White” handset. However, they are described also with “Menu icon setting” set to “Pink gold”, and “Stand-by display” of “Display setting” set to “OFF”.

Unless otherwise specified, the descriptions of the operating procedures in this manual start from the Stand-by display.

Operations are described in the method of “Scroll Selection” (see page 31).

Displays and illustrations described in this manual are for reference. The actual ones might differ.

In this manual, “Osaifu-Keitai compatible i-αppli which supports the IC card function” is described as “Osaifu-Keitai compatible i-

ppli”.

How to Refer to This Manual

By the following search methods, you can find pages where your desired functions and services are described:

How to Read/Refer to This Manual

Note that “FOMA P905i” is referred to as “FOMA phone” in this manual.

The functions which use a microSD memory card are described in this manual; however, you need to obtain a microSD memory card separately to make these functions available. See page 293 for the microSD memory card.

It is prohibited to copy all or part of this manual without permission.

The instructions contained in this manual may be changed without notice.

From the Index

Search from the index when you know the names of functions or services.

From Easy Search

Search from keywords for the functions you frequently use or the functions that are convenient if you can know any.

From the Tabs on the Cover

Search from the tabs printed on the cover.

See the next page for details.

From the Contents



P.6

Search from the contents that categorize functions.

From the Main Functions



P.8

Search from the main functions when you want to use.

From the Function List



P.394

Search from the function list.

From Quick Manual



P.458

Quick Manual gives you a clear, brief description about basic functions. You can take it when you go out. Further, Quick Manual “For Overseas Use” is attached, so refer to it when you use the FOMA phone overseas.

Illustrations for keys

In this manual, the illustrations for keys are simplified. For the illustration for keys used in this manual, see “Phone Parts and Functions” on page 24.

For the description of the operating procedures in this manual, see page 31.

Actual key

Illustration in

this manual

(Body color: Black/White)

-1

(Body color: Red)

(Body color: Pink gold)

Easy Search/Contents/Precautions

How to search for “Alarm” is explained here as an example of search method.

From the Index



P.450

Search for a function or a service name as shown below.

Add to a phonebook entry

Add to phonebook (Phone)

84, 87

Add to phonebook (UIM)

84, 87

Additional service

378

Additional guidance

378

Address link function

164

Alarm

335

Alarm setting

341

Answer setting

Antenna

Any key answer

Power saver

220

Area mail

202

Go to page 335 where “Alarm” is explained.

From Easy Search



P.4

Search for the function you frequently use or that is convenient if you can know any as shown below.

Other things you can do

To reduce the battery consumption ...................107 <Power Saver Mode>

To scan QR codes or Bar codes .......................146 <Bar Code Reader

To check the location where you are,

or the surroundings .........................................

232

To use the microSD memory card.....................293 <microSD Memory Card>

To exchange information using infrared rays .... 303 <Infrared Data Exchange>

To listen to music............................................... 323 <MUSIC Player>

To use the FOMA phone as an alarm clock......335 <Alarm>

To use the FOMA phone as a calculator........... 345 <Calculator>

To use the FOMA phone overseas....................386 <International Roaming>

To bring software programs up to date.............. 434 <Software Update>

To bring security up to date ...............................440 <Scanning Function>

Go to page 335 where “Alarm” is explained.

From the Tabs on the Cover



Cover page

Search for the function you want to set in the order of “Cover” → “First page of Chapter” → “Description page” as shown below.

One Seg

Full Browser/PC Movie

Data Display/Edit/ Management

Music&Video Channel/ Music Playback

Other Convenient Functions

Character Entry

Network Services

PC Connection

Overseas Use

Multiaccess . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Multiaccess› 332

Multitask. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Multitask› 332

Informing You of an Incoming Call/Mail Message by Voice . . . . . . . . . . . . . .‹Reading Aloud› 333

Turning Power On/Off Automatically at a Specified Time. . . . . . . . . . . ‹Auto Power ON/OFF› 335

Using Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Alarm› 335

Using Calendar to Manage Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Schedule› 337

Using ToDo to Manage Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹ToDo› 340

Setting Operating Conditions of Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Alarm Setting› 341

Using Your Original Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Private Menu Setting› 341

Storing Your Name, Mail Address and Other Information. . . . . . . . . . . . . . . . . ‹Own Number› 342

Recording Voice during a Call or Standby as Voice Memo

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Voice Memo during a Call› ‹Voice Memo› 343

Recording Images during a Videophone Call as a Movie Memo . . . . . . . . . . . ‹Movie Memo› 343

Go to page 335 where “Alarm” is explained.

Easy Search/Contents/Precautions

335

Other Convenient Functions

You can set Alarm to alert you at the specified time with an alarm tone, animation and illumination. You can store up to five alarms.

m

StationeryAlarm



Highlight an alarm and pressl()



Do the following operations.

Pressl().

+m-4-4

Alarm

Using Alarm

Item Operation/Explanation

(Alarm)

You can set whether to validate or invalidate the alarm.



ON or OFF

(Time)



Enter the time for sounding the alarm.

You cannot set the same time as the time set for the stored alarm.

(Alarm)



Select a type of alarm tone



Select a folderSelect an alarm tone.

(Volume)



UseBo to adjust the volume.

If you set “Step”, the alarm tone is silent for about three seconds, and then the volume steps up every about three seconds, from Level 1 through Level 6.

(Snooze)

You can set whether to activate Snooze. If you set to “OFF”, set the duration that the alarm tone is to continue sounding.



ON or OFFEnter a ring time (minutes).

You can enter from “01” through “10” in two digits.

(Auto power ON)

You can set whether to turn on the power automatically to make an alarm sound when the alarm time arrives during power off.



ON or OFF

(Prefer manner mode)

You can set the alarm tone which sounds at the specified time during Manner Mode.



ON or OFF

. . . . Sounds at the same volume as set

for “Alarm volume”.

OFF

. . . Sounds at the volume set for this

function.

Function Menu while Alarm is displayed

Function menu

Operation/Explanation

Edit

Go to step 1 of “Using Alarm” on page 372.

Detail

You can display the stored alarm contents.

Set this

You can validate the stored alarm.



YES

You can validate also by pressing

().

Set all

You can validate all the stored alarm.



YES

Release this

You can invalidate the stored alarm.



YES

You can invalidate also by pressing

().

Release all

You can invalidate all the stored alarm.



YES

Information

During a call, the alarm tone sounds at the level set for “Volume” (earpiece volume).

If any of the following events occurs in Snooze state, Snooze is released:

･

When you receive a voice call, videophone call, or PushTalk call

･

When you receive a mail message or Message R/F while “Receiving display” is set to “Alarm preferred”

･

When you receive a location provision request while “Location request menu” or the setting by service is set to other than “OFF”

･

When an alarm tone of “Schedule”, “ToDo”, “Book program” or “Timer recording” sounds.

When you set the power to automatically turn on and an alarm to sound, the default alarm tone sounds if the alarm which is set with the UIM restrictions has been selected.

Turn off the FOMA phone after setting “Auto power ON” to “OFF” when you are near electronic devices using highprecision control or weak signals, or where the use is prohibited such as in airplanes and hospitals.

■

When you set an alarm for “Alarm”, “Schedule”, and “ToDo”

The icon appears on the desktop. “ ” . . . Displayed when an alarm is set for today (except

the setting for past time).

“ ” . . . Displayed when an alarm is set for tomorrow or

onward only.

If you set “Display setting”→“Clock”→“Clock display” to “OFF”, or set the alarm of the stored schedule event/ToDo item to “OFF”, the icons are not displayed.

Note: The page above is a sample.

Menu number (See page 33)

Function name You can find this in Index.

Operating procedure (See page 31)

Reference display (Characters and settings are for reference.)

You can search by chapter.

Options and their explanations

Items shown on the display (Some items cannot be executed.)

Operation and supplementary explanation for each item

Cautions or references for using each function

Operations related to the function and explanations for supplementary operations

Chapter title

Easy Search/Contents/Precautions

Easy Search

To retrieve the operation for the desired function with simple words, refer to the following:

To know convenient functions for making calls

To/Not to notify your phone number to the other party ...

47 <Caller ID Notification> To switch to a videophone call during a voice call...52<Switch to Videophone Call>

To change a volume level of the other party’s voice .....

63 <Volume>

To put a call on hold during a call........................ 64 <Holding>

To do the following when you cannot answer calls

To put an incoming call on hold before answering ....

64 <On Hold> To convey the message that you need to

refrain from talking on the phone ......................65 <Public Mode (Drive Mode)>

...................... 66 <Public Mode (Power Off)>

To record voice/video messages......................... 67 <Record Message Setting>

To change melody or illumination

To adjust the ring volume ....................................64 <Ring Volume>

To change ring tones according to callers........... 84 <Add to Phonebook>

To change ring tones........................................... 98 <Select Ring Tone>

To know incoming calls by vibrator.................... 100 <Vibrator>

To silence the keypad sound............................. 101 <Keypad Sound>

To activate Manner Mode..................................102 <Manner Mode>

To change colors/lighting patterns of Call

indicator for incoming calls.............................. 111 <Illumination>

To change/know display settings

To know the meaning of marks (icons) on the display

............................................................................ 28 <Display>

To change the menu display ............................... 35 <Simple Menu>

To change the Stand-by display (Wallpaper) ....104 <Display Setting>

To display a calendar on the Stand-by display......

104 <Calendar>

To change the character size ............................115 <Character Size>

To make full use of mail

To send Deco-mail ............................................ 175 <Deco-mail>

To send images................................................. 179 <Attachments>

To sort and save mail automatically ..................196 <Auto-sort>

Easy Search/Contents/Precautions

※

1 This is a pay service.

※

2 This is a pay service which is available on a subscription basis.

To make full use of camera

To shoot with the photo light..............................143 <Photo Light>

To change the shooting size.............................. 143 <Image Size>

To save to the microSD memory card ...............144 <Storage Setting (Store In)>

To display shot images......................................274 <Picture Viewer>

To use the FOMA phone with a sense of security

To lock the FOMA phone from away

when it gets lost .............................................. 120 <Omakase Lock>

※1

To keep Phonebook entries from prying eyes ....

126 <Secret Mode>

To reject calls without a caller ID.......................128 <Call Setting without ID>

To reject calls from the phone numbers

not in the Phonebook ......................................129 <Reject Unknown>

To separately store Phonebook and other

data files in preparation for their erasure ........129 <Data Security Service>

※2

To make full use of One Seg

To watch One Seg.............................................247<Activate 1Seg>

To record One Seg programs........ 252

Record Video><

Record Still Images

To book/To set timer recording for One Seg programs

.................................................... 253 <Book Program><Timer Recording>

To change settings of video and audio.............. 256 <User Settings>

Other things you can do

To reduce the battery consumption ...................107 <Power Saver Mode>

To scan QR codes or Bar codes .......................146 <Bar Code Reader

To check the location where you are,

or the surroundings .........................................

232

To use the microSD memory card..................... 293 <microSD Memory Card>

To exchange information using infrared rays ....303 <Infrared Data Exchange>

To listen to music...............................................323 <MUSIC Player>

To use the FOMA phone as an alarm clock ...... 335 <Alarm>

To use the FOMA phone as a calculator...........345 <Calculator>

To use the FOMA phone overseas....................386 <International Roaming>

To bring software programs up to date.............. 434 <Software Update>

To bring security up to date ...............................440 <Scanning Function>

The operating procedures for frequently used functions are summarized in Quick Manual. (See page 458)

Easy Search/Contents/Precautions

Contents

How to Read/Refer to This Manual.......................................1

Easy Search ........................................................................... 4

Contents .................................................................................6

Main Functions of FOMA P905i............................................8

Making Full Use of FOMA P905i!........................................10

Safety Precautions.............................................................. 12

Notes on Handling .............................................................. 17

Intellectual Property Rights ............................................... 20

Accessories and Main Options.......................................... 22

Before Using the Handset

Phone Parts and Functions, Styles, Display, Method for Selecting Menu, Simple Menu, Guide, UIM (FOMA Card), Battery, Charging, Power ON/OFF, Select Language, Initial Setting, Set Time, World Time Watch, Caller ID Notification, Own Number, etc.

Voice/Videophone Calls

Making a Call/Videophone Call, Switching between a Voice Call and Videophone Call, Call Records, Chaku-moji, WORLD CALL, Hands-free, Receiving a Call/ Videophone Call, Answer Setting, Volume, Ring Volume, Public Mode (Drive Mode), Public Mode (Power Off), Record Message Setting, Chara-den, etc.

PushTalk

What is PushTalk?, Making a PushTalk Call, Add Member, Receiving a PushTalk Call, PushTalk Phonebook, Setting PushTalk Calling/Receiving, etc.

Phonebook

Available Phonebooks, Add to Phonebook (FOMA phone/UIM), Group Setting, Search Phonebook, No. of Phonebook, Two-touch Dial, Voice Dial, Data Security Service, etc.

Sound/Screen/Light

Settings

Select Ring Tone, Vibrator, Manner Mode, Display Setting, Private Window, Backlight, Color Theme Setting, Menu Icon Setting, Kisekae Tool, Feel Settings, Illumination, Desktop Icon, Font, Character Size, etc.

Security Settings

117

Passwords, Change Security Code, UIM Setting, Releasing PIN Lock, Lock All, Omakase Lock, Self Mode, Personal Data Lock, Keypad Dial Lock, Secret Mode, Mail Security, Restrictions, Call Setting without ID, Reject Unknown, etc.

Camera

131

Before Using Cameras, Still Image Shoot, Moving Image Shoot, Settings for Shooting Images, Setting Image Size/Image Quality, Bar Code Reader, Text Reader

i-mode/i-motion/i-Channel

151

What is i-mode?, iMenu, Last URL, My Menu, Change i-mode Password, Enter URL, Bookmark, Screen Memo, Download, i-mode Settings, SSL Certificate, Client Certificate, What is i-motion?, What is i-Channel?, etc.

Mail

171

i-mode Mail, Deco-mail, Template, Attachments, Photo-sending, Mail Auto-receive, Receive Option, Check New Message, Inbox, Outbox, Draft, Auto-sort, Message R/F, Area Mail, Chat Mail, SMS, Web Mail, etc.

i-αppli

209

What is i-αppli?, i-αppli Download, i-αppli Run, iα

ppli Settings,

Starting i-

ppli Automatically, i-αppli Stand-by Display, iα

ppli(microSD)

Osaifu-Keitai/ToruCa

223

What is Osaifu-Keitai?, What is iC Transfer Service?, Osaifu-Keitai Compatible i-

ppli, What is ToruCa?, Obtain ToruCa Files, ToruCa Viewer, ToruCa File List/Detailed ToruCa File Display, ToruCa Settings, IC Card Lock

Easy Search/Contents/Precautions

GPS Function

231

About Using GPS Function, Position Location, GPS compatible i-αppli, Provide Location, Notify of Location, Location History, Service Settings, GPS Settings

One Seg

243

What is One Seg?, Before Using One Seg, Channel Setting, Activate 1Seg, Program Guide i-

ppli, Data Broadcasting, TVlink,

Recording One Seg, Book Program/Timer Recording, User Settings

Full Browser/PC Movie

259

Full Browser, Full Browser Settings, What is PC Movie?, Downloading PC Movies, PC Movie Player

Data Display/Edit/

Management

271

Data Box, Picture Viewer, i-motion Player, Video Player, Chara-den, Melody Player, Kisekae Tool, microSD Memory Card, Managing Folders, Infrared Data Exchange, iC Communication, PDF Viewer, Document Viewer, AV Output, etc.

Music&Video Channel/

Music Playback

315

What is Music&Video Channel?, Setting Programs, Playing Back/Operating Programs, Playing Back Music, Saving Music Files, MUSIC Player, Playlist

Other Convenient

Functions

331

Multiaccess, Multitask, Reading Aloud, Alarm, Schedule, ToDo, Private Menu Setting, Own Number, Voice Memo, Movie Memo, Call Data, Calculator, Text Memo, UIM Operation, Bluetooth, Reset Settings, Initialize, etc.

Character Entry

355

Character Entry, Mode 1 (5-touch), Common Phrases, Cut/Copy/Paste, Own Dictionary, Learned Words, Download Dictionary, Mode 2 (2-touch), Mode 3 (NIKO-touch)

Network Services

363

Check New Messages, Voice Mail, Call Waiting, Call Forwarding, Nuisance Call Blocking, Caller ID Request, Dual Network, English Guidance, Service Numbers, Arrival Call Act, Remote Control, Multi Number, 2in1, OFFICEED, Additional Service

PC Connection

379

Available Data Communication, Before Using, Preparation Flow for Data Communication, AT Command, CD-ROM, DoCoMo Keitai Datalink

Overseas Use

385

Outline of International Roaming (WORLD WING), Available Services, Confirmation for Using, Making a Call from the Country You Stay, Receiving a Call, Switch 3G/GSM, Network Search Mode, Operator Name Display, Set Roaming Guidance, Network Services, etc.

Appendix/External Devices/

Troubleshooting

393

Function List, Options and Related Equipment, Troubleshooting, Error Messages, Warranty and Maintenance Services, i-mode Trouble Diagnosis Site, Software Update, Scanning Function, Specifications, Number of Savable/Storable/ Protectable Items, SAR, Export Administration Regulations, etc.

Index/Quick Manual

449

Index, Quick Manual, Quick Manual “For Overseas Use”

Easy Search/Contents/Precautions

FOMA (Freedom Of Mobile multimedia Access) is the name of the DoCoMo service based on the W-CDMA format, authorized as one of the world’s standards for third-generation mobile telecommunication systems (IMT-2000).

Main Functions of FOMA P905i

Remarkable i-mode!

i-mode is an online service that enables you to get useful information from i-mode menu sites (programs) or i-mode web pages. This service also enables you to send or receive mail messages with ease.

◆

i-mode mail/Deco-mail/ Decomail-pictograph

P.172, P.175, P.272

Besides mail text, you can attach up to 2 Mbytes of files or 10 files (JPEG, ToruCa, PDF, etc.) in total. The FOMA phone supports Deco-mail/Decomail-pictographs, so you can change the character color, character size, and background color of mail text, and insert images and moving pictographs.

◆Mega i-αppli/Intuitive Games P.210

By downloading i-αppli programs from sites, you can enjoy playing games or have stock price information or weather forecasts updated automatically. As the large capacity mega i-

ppli is supported, you can enjoy playing high-resolution 3D games and full-length role playing games. In addition, the intuitive games are supported, which you can play by inclining or swinging your FOMA phone as you sense. As the voice recognition is supported by P905i, the operation responding to your voice is also available.

◆High-Speed Area Supported P.380

FOMA High-Speed Area is supported so that high speed communication is available with download speed of up to 3.6 Mbps and upload speed of up to 384 kbps.

◆International Roaming P.386

You can use your FOMA phone, phone number, and mail address overseas as they are. (Supported in GSM/3G area) Voice calls, videophone calls, i-mode, i-mode mail, SMS, and network services are available. “

しゃべって翻訳

forP

(Speech Translation for P)”, which translates spoken Japanese into English and spoken English into Japanese, is pre-installed.

◆GPS P.232

You can use the location information obtained by GPS to search for a map of your location and information of the surrounding area, notify of your location by attaching to mail, and navigate yourself to your destination. The pre-installed

“

地図アプリ

(Map Application)” enables you to easily use the

highly accurate map.

◆Chaku-uta Full®/Uta-hodai/

Music&Video Channel

※

/Video Clips

P.168, P.316, P.321, P.323

This FOMA phone supports Chaku-uta Full® that enables you to download a whole music file and Uta-hodai that enables you to enjoy listening music as much as you like at a flat rate. This FOMA phone also supports Music&Video Channel that, just by setting up beforehand, automatically downloads music programs in the night. You can watch programs containing moving images on your P905i. Further, this FOMA phone supports up to 10 Mbytes of i-motion movies, so it also supports Video Clip that enables you to enjoy a whole music clip file.

“Chaku-uta Full” is a registered trademark of Sony Music Entertainment Inc.

※

This is a pay service which is available on a subscription basis.

◆Osaifu-Keitai/ToruCa P.224, P.225

By downloading Osaifu-Keitai compatible i-αppli, you can replenish electronic money from a site into the IC card in the FOMA phone and check your account for the balance and usage details. In addition, the “DCMX” i-

ppli program that provides the DoCoMo credit service is pre-installed. Further, “iC transfer service” is supported so that you can easily move data from the existing IC card to a new one when you replace your FOMA phone such as at the time of phone model change. ToruCa is an electronic card that you can obtain from scanning devices or sites and can easily exchange using mail or infrared data exchange.

◆Kisekae Tool P.109, P.292

By downloading the displays of your cartoon characters from an i-mode site, you can change the Stand-by display or Menu display at a time. You can change the order of displayed menus according to the frequency of use to customize the Menu display as you like.

Easy Search/Contents/Precautions

◆Bluetooth P.348

The wirelessly-connected FOMA phone and a Bluetooth device enable you to talk or listen to music while you are carrying the FOMA phone in your bag.

◆Feel＊Talk/Feel＊Mail P.109

Animation of 45 characters and illumination reproduces the atmosphere of conversation or mail messages.

◆Wide VGA Display

You can display still or moving images in the wide VGA (480 dots x 854 dots) display of approx. 3.0 inches, and you can enjoy watching One Seg programs on the impressive display. Also, the light sensor automatically adjusts the backlight in accordance with the ambient brightness, and the LCD AI compensate the image quality in accordance with the brightness.

◆Horizontal Open Style P.26

You can watch One Seg programs and videos in the wide horizontal display in Horizontal Open Style. Further, you can see the Internet web pages with Full Browser without scrolling sideways. Work with Style enables you to activate One Seg just by switching styles.

◆One-push Open P.26

■

One-push Answer 

P.63

When a call comes in, just press the one-push open button, and you can open the FOMA phone to answer the call.

■

Recv. Mail/Call at Open 

P.106

When a missed call or new mail message is found, just press the one-push open button, and you can open the FOMA phone to display the detailed Missed Call display or the Inbox List.

◆Mail Blind P.198

You can show the characters on the detailed mail display and Message Composition display in gray to make them hard to see from persons around you. (The characters on the Character Entry display are not shown in gray.)

◆Image Stabilizer P.144

Owing to the Image Stabilizer function, you can shoot still images or moving images with less blur by the outside camera.

◆Document Viewer P.310

On your FOMA phone, you can display Microsoft Word files, Microsoft Excel files, and Microsoft PowerPoint files created by personal computers.

◆Security Settings P.117

Various settings such as the lock functions and security settings for “safety” are available.

■

Omakase Lock 

P.120

When you have lost the FOMA phone, you can lock the FOMA phone and release it by contacting DoCoMo. For inquiries, see the back page of this manual. Omakase Lock is a pay service

※

You are not charged if you apply for this service at the same time as applying for the suspension of the use or during the suspension.

Note that Omakase Lock might be activated by an offer from the contractor of the FOMA phone when the contractor and the user of the FOMA phone differ.

■

Data Security Service 

P.129

This service enables you to save Phonebook entries, images, and mail messages from your FOMA phone to the Data Storage Center, and restore the saved data, when you lost your FOMA phone or in other cases, to your FOMA phone from the Data Storage Center. Further, you can edit or manage data held at the Data Storage Center using your personal computer and can reflect the edited data to your FOMA phone. For details on Data Security Service, refer to “Mobile Phone User’s Guide [i-mode]”. For inquiries, see the back page of this manual. Data Security Service is a pay service that is available on a subscription basis.

◆Network P.363

Voice Mail Service (Charged)

・

A separate subscription is required.

Dual Network Service (Charged)

・

A separate subscription is required.

SMS (Free)

・

No subscription is required.

Call Waiting Service (Charged)

・

A separate subscription is required.

Multi Number (Charged)

・

A separate subscription is required.

Call Forwarding Service (Free)

・

A separate subscription is required.

2in1 (Charged)

・

A separate subscription is required.

Easy Search/Contents/Precautions

Making Full Use of FOMA P905i!

◆Videophone P.50

You can talk with a person who is away from you, seeing each other. By the default setting, the voice of the other party is set to be output from the speakers, so you can start talking immediately. You can switch, without disconnecting, from an ordinary voice call to a videophone call.

◆PushTalk P.76

You can communicate with multiple persons (up to five persons including yourself) just by selecting them from the PushTalk Phonebook and pressing the PushTalk key.

◆i-Channel P.169

i-Channel distributes graphical information such as news or weather forecast. By selecting a channel you want to see from the Channel List, you can obtain detailed expressive information created by Flash (see page 154).

This is a pay service which is available on a subscription basis.

The service is provided only in Japanese.

◆One Seg P.244

You can watch One Seg (terrestrial digital TV broadcasting service for mobile objects) programs. You can display captions and data broadcasting, record video or still images from a program being broadcasted. Moreover, you can book the One Seg programs you want to watch or set timer recording. While watching a One Seg program, you can compose i-mode mail messages or check the sent/received i-mode mail messages by using multiple windows as well.

Talk while pressing the PushTalk key

Receiver

Hello!

Caller

Talk between two persons

Caller

Receiver

Dial

I’m coming soon.

Receiver

Talk with multiple persons

Talk while pressing the PushTalk key

Before contract After contract

Connected

-Zo

Easy Search/Contents/Precautions

◆2in1 P.372

This service enables you to have two number/two mail addresses on your single FOMA phone and to use your FOMA phone as if you were using two sets, by using the dedicated mode function. You can sort Phonebook entries, mail boxes, dialed/received call records, and Stand-by displays into “A mode” and “B mode” to manage them separately. You can also use “Dual mode” to simultaneously manage both A and B modes.

This is a pay service which is available on a subscription basis.

◆MUSIC Player P.323

On a single player, you can play back and enjoy Chaku-uta Full® music files, Windows Media

Audio (WMA) files, and SD-Audio files. You can download Chaku-uta Full

music files from sites and may be able to display their images and lyrics while playing them back. In the case of SD-Audio or WMA files, you can obtain your favorite music files from music CDs or Internet web pages and save them on the microSD memory card by using your personal computer. You can save music files also by using the Napster

application program.

◆Chaku-moji P.55

While calling up the other party, you can have your message displayed on his/her Call Receiving display. The receiving end can know your subject/feeling by reading the message before answering the call.

A Mode

Phone number: 090-AAAA-AAAA

Mail address: XXA@docomo.ne.jp

Phonebook: For A Mode

B Mode

Phone number: 090-BBBB-BBBB

Mail address: XXB@docomo.ne.jp

Phonebook: For B Mode

Call/Mail in A Mode

Call/Mail in B Mode

Mode

Phonebook A Inbox A Dialed/Received Calls A Voice Mail A

・・

Dual

Mode

Phonebooks A, B Inboxes A, B Dialed/Received Calls A, B Voice Mail A, B

・・

Mode

Phonebook B Inbox B Dialed/Received Calls B Voice Mail B

・・

Easy Search/Contents/Precautions

■

Before using the FOMA phone, read these safety precautions carefully so that you can use it correctly. After reading the precautions, keep them in a safe place.

■

Be sure to observe these safety precautions because they are designed to protect you or those around you from causing injury and to avoid unnecessary damage to the property.

■

The symbols below indicate the levels of danger or damage that can be caused if the particular precautions are not observed.

■

The following symbols show specific directions:

■

“Safety Precautions” are divided into the following six sections:

General precautions for FOMA phone, batteries, adapters/chargers, and UIM.............................................................P.13

Precautions for FOMA phone.........................................................................................................................................P.13

Precautions for batteries ................................................................................................................................................P.15

Precautions for adapters/chargers.................................................................................................................................P.16

Precautions for UIM .......................................................................................................................................................P.17

Notes on using near electronic medical equipment .......................................................................................................P.17

Safety Precautions

Danger

This symbol indicates that incorrect handling will almost certainly cause death or serious injury.

Warning

This symbol indicates that incorrect handling poses a risk of causing death or serious injury.

Caution

This symbol indicates that incorrect handling poses a risk of causing injury or damage to the product or property.

Denotes things not to do. (Prohibition)

Denotes not to disassemble.

Denotes not to use where it could get wet or not to wet it.

Denotes not to touch with wet hands.

Denotes mandatory instructions (matters that must be complied with).

Denotes to pull the power plug out of the outlet.

Always follow the safety precautions.

Don’t

Do not

disassemble

Avoid

Water

Not wet

hands

Pull the

power plug

out

Easy Search/Contents/Precautions

Do not use or leave the FOMA phone and its accessories in places with a high temperature such as near fire or places exposed to direct sunlight, or in cars under the blazing sun.

The devices could be deformed or malfunction, or the battery may leak, overheat, burst, or catch fire, thus resulting in the deterioration of performance and shortening of the life of devices. Also, part of the case could get heated, causing bare skin burns.

Do not disassemble, modify or solder the FOMA phone or accessories.

Accidents such as fire, injury, or electric shock, or malfunction may result. The battery may leak, overheat, burst or catch fire.

Do not wet the FOMA phone or accessories.

If liquids such as water or pet urine get onto them, overheating, electric shock, fire, malfunction, injury or others may result. Pay attention to the place of use and the way of handling.

Use only the batteries and adapters/chargers approved by DoCoMo for your FOMA phone.

If you use any type of battery, adapter or charger other than the specified one, your FOMA phone, battery or other accessories may leak, overheat, burst, catch fire or malfunction. Battery Pack P15 FOMA AC Adapter 01/02 FOMA AC Adapter 01 for Global use FOMA DC Adapter 01/02 Desktop Holder P24 FOMA Dry Battery Adapter 01 FOMA Portable Charging Adapter 01 FOMA USB Cable with Charge Function 01

※

For other compatible products, contact a handling counter such as a DoCoMo shop.

Do not place the batteries, the FOMA phone, adapters/chargers, or UIM in cooking appliances such as microwave ovens or high-pressure containers.

The battery may leak, overheat, burst, or catch fire. The FOMA phone or the adapter/charger may overheat, smoke, or catch fire, or its circuit parts may become damaged.

Do not throw the FOMA phone or accessories, or subject them to severe shocks.

The battery may leak, overheat, burst, or catch fire. Also, malfunction or fire may result.

Be careful not to let electroconductive materials (metal pieces, pencil leads etc.) contact with the charging terminals or connector terminal. Also, make sure that those are not entered into the inside of the FOMA phone.

Short-circuit could cause fire or malfunction of the FOMA phone.

General precautions for FOMA phone, batteries, adapters/chargers, and UIM

Danger

Warning

Don’t

Do not

disassemble

Avoid Water

Don’t

When you are in a place such as a gas station where flammable gas is generated, turn off the FOMA phone, and never do charging. Otherwise, catching fire may result.

Ensure that you use Osaifu-Keitai with the FOMA phone turned off when you are in the vicinity of the gas station. (When IC card Lock is set, turn off the power with the lock released.)

If odor, overheat, discoloration, or deformation is detected during use, battery charge, or storage, immediately observe the following:

1. Pull the power plug out of the outlet or cigarette lighter socket.

2. Turn off the power to the FOMA phone.

Remove the battery pack from the FOMA phone. If you use the FOMA phone and its accessories as they are, overheat, burst, or catching fire could result or the battery could leak.

Do not place the FOMA phone or accessories on unstable locations such as wobbly tables or slanted locations.

The FOMA phone or accessories may fall, resulting in injury or malfunction.

Do not store in humid or dusty places, or in high temperature environments.

Malfunction may result.

If children use the FOMA phone or accessories, a guardian should explain the safety precautions and correct operations. The guardian should also make sure that the instructions are followed during use.

Otherwise, injury may result.

Keep out of the reach of babies and infants.

Accidental swallowing or injury may result.

Be especially careful when you use the FOMA phone for a long time with the adapter/charger connected. If you use i-

ppli programs, talk on the videophone, watch One Seg and so on for a long time during charging, the temperature of the FOMA phone, battery pack, or adapter/ charger might rise.

If you directly touch the part of high temperature continuously, redness, itching, or rash might be caused or low-temperture bare skin burns may result depending on your physical conditions or predisposition.

Do not directly point the infrared data port at someone’s eyes during transmission.

His/her eyes may possibly be affected. Other infrared devices may operate erroneously if the infrared data port is pointed at them during transmission.

Caution

Precautions for FOMA phone

Warning

Don’t

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Easy Search/Contents/Precautions

Do not shine the photo light close to eyes.

Doing so can damage eyesight. Also, accidents such as injury might occur if someone is startled or dazzled by the light.

Do not put the FOMA phone in the place where it could be affected by an expanded airbag, e.g., on the dashboard.

If the airbag expands, the FOMA phone could hit you and others, causing accidents such as injury and the FOMA phone could malfunction and become damaged.

If you have any implanted electronic medical equipment, do not place your FOMA phone in a chest pocket or inner pocket.

If the FOMA phone is positioned close to electronic medical equipment, it may cause that equipment to malfunction.

Do not allow liquids such as water, or foreign materials such as metal pieces or flammable materials to get into the UIM insertion slit or microSD memory card slot of the FOMA phone.

Fire, electric shock or malfunction may occur.

Do not light the photo light to drivers of a car, and others.

It disturb the driving, and accidents may result.

Turn off the FOMA phone in places where use is prohibited such as in airplanes and hospitals.

Otherwise, electronic devices and electronic medical appliances may be adversely affected. If the Auto Power ON function is set, deactivate the setting, then turn the power off. For use inside medical facilities, make sure that you comply with their regulations. You may be punished for using the FOMA phone in airplanes, which is prohibited by law.

When talking with the FOMA phone set to Hands-free, be sure to keep the FOMA phone away from your ear. Further, when you play games or play back music with the earphone/ microphone connected, adjust the sound volume to moderate volume.

The excessive volume impairs your hearing. Further, accidents may result if it is difficult to hear surrounding sound.

For those with weak heart conditions, the vibrator and ring volume must be adjusted carefully.

Those functions may cause an effect on the heart.

If thunder starts to rumble while you are using the FOMA phone outdoors, house the antenna, turn off the power, and move to a safe place.

Otherwise, you could be struck by lightning or suffer an electric shock.

Don’t

Turn off the FOMA phone when near electronic devices using high-precision control or weak signals.

The FOMA phone may possibly cause these devices to malfunction.

※

Electronic devices that may be affected: Hearing aids, implanted cardiac pacemakers, implanted defibrillators, other medical electronic devices, fire alarms, automatic doors and other automatically controlled devices. If you use an implanted cardiac pacemaker, implanted defibrillator or any other electronic medical device, consult the manufacturer or retailer of the device for advice regarding possible effects from the radio waves.

If the display part or camera lens is broken, be careful about broken glasses or the exposed interior of the FOMA phone.

Plastic panels are used for the surfaces of the display part and camera lens so that glasses do not easily get scattered, however, pay attention not to erroneously touch the broken part or interior. Otherwise, your hands may hurt.

Do not swing the FOMA phone by its antenna or strap.

The FOMA phone may hit you or persons around you, and accidents such as injury or malfunction and damage may result.

Do not use in places crowded with people.

The antenna may hit against others, causing injury.

Do not use the FOMA phone with the damaged antenna.

If the damaged antenna comes in contact with your skin, injury such as a burn could be caused.

When using the motion tracking, ensure that you check around you for safety, securely take hold of your FOMA phone, and do not swing to an extent more than necessitated.

The motion tracking is the function to incline or swing the FOMA phone for operation. If you excessively swing your FOMA phone, it might happen that it hits against persons or objects, resulting in critical accidents or damage.

When a metallic strap is attached to your FOMA phone, be careful that it does not hit against persons or objects when using the motion tracking.

Accidents such as injury or malfunction and damage may result.

Do not place magnetic cards or similar objects near the FOMA phone or between phone parts.

Information on magnetic cards such as cash cards, credit cards, telephone cards and floppy disks may be deleted.

Caution

Don’t

Easy Search/Contents/Precautions

Do not bring magnetic substances close to your FOMA phone.

Strong magnetic items might result in erroneous operation.

If you erroneously break the display part and then crystal liquid get leaked, never take or suck the liquid to or into your mouth, or apply to skin. If the crystal liquid get put into the eyes or mouth, immediately cleanse with pure water and then see your doctor. When it adheres to your skin or clothes, immediately wipe it away with alcohol etc., and then cleanse with detergent.

Otherwise, the loss of eyesight or injury to your body may result.

Do not close your ears to the speakers while a ring tone sounds or playing back a melody by the FOMA phone.

Otherwise, your hearing could be impaired.

Do not open the FOMA phone by pressing the one-push open button near persons around you or your face.

The FOMA phone may hit you or persons around you, causing accidents and injuries.

Do not use the FOMA phone with the hook for Horizontal Open Style protruded.

Otherwise, injury may result.

Electronic devices in some types of cars can be affected by use of the FOMA phone.

For safety’s sake, make sure not to use the FOMA phone inside such cars.

Itching, rash or eczema may be caused depending on your physical conditions or predisposition. If an abnormality occurs, stop using the FOMA phone immediately, and then seek medical attention.

Metals are used for the following parts:

Be careful not to get your finger or a strap caught between the FOMA phone when you close or open it.

Accidents such as injury or damage may result.

Where it is used Material Finishing

Charging terminal Phosphor

bronze

Gold-plated finish with nickel-plated ground

Metal part of the One Seg antenna

Brass Chrome-plated finish with

nickel-plated ground

Hook for Horizontal Open Style

Stainless steel Chrome-plated finish with

nickel-plated ground

Command Navigation key

Polycarbonate Steam pressed aluminum,

Hard coat

“P905i” logo panel on the Private window side

ABS Steam pressed tin,

Hard coat

Metal part of the one-push open button

Aluminum

−

Don’t

When you watch a One Seg program, watch in a place bright enough taking a certain distance from the display.

Otherwise, your visual acuity could be reduced.

■

Check the description on the label of the battery pack for the type of battery.

Do not let any metal object such as a wire come in contact the battery terminals. Also do not carry or store the battery together with any metal objects like a necklace.

The battery may leak, overheat, burst or catch fire.

Do not use excessive force to attach the battery to the FOMA phone even when you cannot attach it successfully. Also, check that the battery is the right way round when you attach it.

The battery may leak, overheat, burst or catch fire.

Do not throw the battery into fire.

The battery may leak, overheat, burst or catch fire.

Do not pierce it with nails, hit it with a hammer, or step on it.

The battery may leak, overheat, burst or catch fire.

If the battery fluid gets into your eyes, do not rub them. Flush your eyes with clean water and get medical attention immediately.

Otherwise, the loss of eyesight may result.

If charging is not completed at the end of the specified charging time, stop charging.

Otherwise, the battery may leak, overheat, become damaged or catch fire.

Immediately stop using the FOMA phone and keep it away from fire if the battery leaks or emits an odor

The leaked battery fluid may ignite, causing fire or burst.

When any abnormality due to external shock such as the deformation or scratches by dropping is found on the battery pack, immediately stop using it.

The battery may leak, overheat, burst, or catch fire. Also, malfunction or fire may result.

Precautions for batteries

Description Type

Li-ion Lithium-ion battery

Danger

Warning

Don’t

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Easy Search/Contents/Precautions

Be careful that your pets do not bite into the battery pack.

The battery may leak, overheat, burst, or catch fire. Also, malfunction or fire may result.

An exhausted battery should not be disposed of with other waste.

The battery may catch fire or damage the environment. After insulating the battery terminals with tape, take it to a handling counter such as a DoCoMo shop or dispose of it in accordance with local waste disposal regulations.

Do not charge the wet battery.

The battery pack may overheat, catch fire, or burst.

If the battery fluid comes in contact with skin or clothes, immediately stop using, then rinse it out thoroughly with clean water.

Skin injury may result.

Do not use a damaged adapter/charger cord or power cord.

Electric shock, overheating or fire may result.

Do not use the AC adapter and desktop holder in steamy places such as a bathroom.

Electric shock may occur.

The DC adapter is for use only in a negative (-) grounded vehicle. Do not use it in a positive (+) grounded vehicle.

Fire may result.

If it starts to thunder, do not touch the FOMA phone and adapter/charger.

You might be struck by lighting or suffer an electric shock.

Never short-circuit the charging terminals when the adapter is plugged into the power outlet or cigarette lighter socket. Also, never touch the charging terminals with fingers or other bare skin.

Fire, malfunction, electric shock or injury may result.

Place the charger and desktop holder on a stable location during charging. Do not cover or wrap the charger and desktop holder in cloth or bedding.

The FOMA phone may drop off, or the charger and desktop holder may overheat, causing fire or malfunction.

Caution

Precautions for adapters/chargers

Warning

Don’t

Do not touch the power cord of the adapter/charger, or power outlet with wet hands.

Electric shock may result.

Use the adapter/charger at the specified V AC.

If you use it at a wrong voltage, fire or malfunction may result. When using the FOMA phone overseas, use FOMA AC adapter available overseas. AC adapter: 100 V AC DC adapter: 12/24 V DC [For negative (-) grounded vehicles only] AC adapter available overseas: 100 V to 240 V AC [Connect only to household AC outlet]

If a fuse of the DC adapter has blown, replace it with a specified fuse.

If you use an unspecified fuse, fire or malfunction may result. For the specified fuse, refer to each instruction manual.

Keep the power plugs dust-free.

Otherwise, fire may result.

When plugging the AC adapter into the power outlet, firmly plug it in, taking care not to contact with metal straps or the like.

Otherwise, electric shock, short-circuit or fire may result.

When pulling the adapter/charger out of the outlet or cigarette lighter socket, do not forcibly pull the adapter/charger cable or power cable, instead take hold of the power plug and then pull.

If you pull the plug out by the cord, the cord may be damaged, which could result in electric shock or fire.

When the adapter/charger is not to be used for a long period of time, unplug the power cord from the outlet.

Otherwise, electric shock, fire, or malfunction may result.

If liquids such as water get in the charger, unplug the power cord immediately from the outlet or cigarette lighter socket.

Otherwise, electric shock, smoke or fire may result.

Do not place heavy objects on the adapter/charger cord and power cord.

Electric shock or fire may result.

Before cleaning, pull the power plug out of the outlet or cigarette lighter socket.

Otherwise, electric shock may result.

Caution

Not wet

hands

Pull the

power plug

out

Pull the

power plug

out

Don’t

Pull the

power plug

out

Easy Search/Contents/Precautions

Be careful not to touch the cut surface of the UIM (IC portion) when removing it.

You may hurt your hand or fingers.

■

The description below meets “Guidelines on the Use of Radio-communication Equipment such as Cellular Telephones – Safeguards for Electronic Medical Equipment” by the Electromagnetic Compatibility Conference Japan.

Comply with the following in hospitals or health care facilities:

Do not carry the FOMA phone into operating rooms, intensive care units (ICU) or coronary care units (CCU).

Turn off the FOMA phone in hospital wards.

If there is any electronic medical equipment near you, turn off the FOMA phone even when in a location such as a lobby.

Comply with any regulations of hospital and health care facilities instructing you not to use or carry in a mobile phone.

If the Auto Power ON function is set, deactivate the setting, then turn the power off.

Turn off the FOMA phone in crowded areas such as inside trains during rush hour, as someone with an implanted cardiac pacemaker or implanted defibrillator may be near you.

Operation of an implanted cardiac pacemaker or implanted defibrillator can be affected by radio waves.

If you use an implanted cardiac pacemaker or implanted defibrillator, use the mobile phone 22 cm or more away from an implanted cardiac pacemaker or implanted defibrillator.

Operation of an implanted cardiac pacemaker or implanted defibrillator can be affected by radio waves.

Patients using electronic medical equipment other than implanted cardiac pacemakers or implanted defibrillators (outside medical establishments for treatment at home, etc.) should check the influence of radio waves upon the equipment by consulting its manufacturer.

Operation of electronic medical equipment can be affected by radio waves.

Precautions for UIM

Caution

Notes on using near electronic medical equipment

Warning

■

Do not wet the equipment.

The FOMA phone, battery, adapter/charger, and UIM are not waterproofed. Do not use them in environments, which are high in humidity such as in bathrooms, and do not allow them to get wet from rain. Furthermore, if carrying them against your body, they become moist due to perspiration and the internal parts may become corroded, causing malfunction. If the parts are found to have been damaged due to exposure to the liquids, any repairs will not be covered by warranty, or repairs may not be possible. This may be repaired at a cost if repairs are possible.

■

Use a dry soft cloth such as the one for cleaning glasses to clean the equipment.

The screen of the FOMA phone sometimes has a special

coating so that they are easier to see. If you rub it roughly with a dry cloth, it might be scratched. Take care of the way of handling, and use only a dry, soft cloth such as the one for cleaning glasses. If the screen is left with water drop or stain adhered, smear may be generated or the coating might peel off.

Do not use alcohol, thinner, benzene, detergent or other

solvents for cleaning, otherwise the printing may be removed or discoloration may result.

■

Occasionally clean the terminals of the equipment using a dry cotton swab.

If the terminals become soiled, the connection might deteriorate so that the power turns off or the battery does not charge fully. Wipe the terminals with a dry cloth or cotton swab.

■

Do not place the FOMA phone near an air conditioner outlets.

Condensation may form due to rapid changes in temperature, and this may corrode internal parts and cause malfunction.

■

Do not apply excessive force onto the FOMA phone and battery pack.

If you put the FOMA phone in a bag along with many other articles or sit with the FOMA phone in a clothes pocket, the LCD display, internal circuitry and the battery pack could be damaged or malfunction. Also, if your FOMA phone is left with an external device connected to the connector terminal or earphone/microphone terminal, the connector could be damaged, or malfunction.

■

Carefully read each instruction manual attached to the FOMA phone, battery pack, adapter/charger, or desktop holder.

■

Do not rub or scratch the display part with metals.

Doing so might cause damage to the part, resulting in trouble or malfunction.

■

Avoid using in extremely high or low temperatures.

The FOMA phone should be used within a temperature range of 5°C to 35°C and a humidity range of 45% to 85%.

■

The FOMA phone, if operated near landline phones, television sets, radios or other devices that are in use, may affect them. You should operate your FOMA phone as far away from such equipment as possible.

Notes on Handling

General notes

Notes on handling the FOMA phone

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Easy Search/Contents/Precautions

■

It is recommended that you make separate notes of the information stored in the FOMA phone and keep such notes in a safe place.

We take no responsibility for any loss of the stored data items.

■

Do not insert an external device to the connector terminal or earphone/microphone terminal at a slant when connecting, and do not pull it out when it is inserted.

Malfunction or damage may result.

■

Make sure that nothing, such as a strap, gets caught between the parts of the FOMA phone when you close it.

Otherwise, malfunction or damage may result.

■

The FOMA phone becomes warm during use or charging but this is not an abnormality. Use the FOMA phone as it is.

■

Do not leave the camera in places exposed to direct sunlight.

Pixels may be discolored or burns may result.

■

Usually, use your FOMA phone with the caps to the Earphone/Microphone/AV output terminal and connector terminal mounted.

Dust or water might enter into the FOMA phone, causing malfunction.

■

Do not operate the FOMA phone with the rear cover left removed.

The battery pack might come out, or trouble or damage may result.

■

Do not apply an excessively thick sticker onto the surfaces of the display, keys, or buttons.

Damage may result.

■

While you are using the microSD memory card, never take it off or turn the power to the FOMA phone off.

Data may be erased or damage may result.

■

Batteries have a limited life.

Though it varies depending on the usage state, you are advised to replace the battery if its usable time is extremely short even when you fully charge it. Make sure that you buy the specified battery.

■

Charge the battery in a place with an appropriate ambient temperature of 5°C to 35°C.

■

Make sure that the battery is charged when you use the FOMA phone for the first time or have not used it for a long period of time.

■

The usable time of the battery differs depending on the usage environment or its remaining life.

■

Depending on how the battery pack is used, it might swell as its operating life becomes short, but this is not a problem.

■

Store the batteries in a place out of direct sunlight.

When you do not use the battery for a long time, remove the battery from the FOMA phone or adapter/charger with the battery power completely drained, and store it in the polyethylene bag used for wrapping.

■

Do not leave and store the battery pack as is with no battery remained.

The performance and operating life of the battery might be lowered or shortened.

■

Charge the battery in a place with an appropriate ambient temperature of 5°C to 35°C.

Notes on handling batteries

Notes on handling chargers/adapters

■

Charge the battery where:

・

There is very little humidity, vibration, and dust.

・

There are no landline phones, television sets or radios nearby.

■

During charging, the adapter/charger may become warm. This is not an abnormality, so continue charging.

■

Do not use the DC adapter for charging the battery when the car engine is not running.

The car battery could go flat.

■

When using the power outlet having the disengaging prevention mechanism, observe the instructions given in that instruction manual.

■

Do not give a strong shock. Also, do not deform the charging terminals or terminal guide.

Malfunction may result.

■

Never use more force than necessary when inserting/ removing the UIM.

■

The UIM may become warm during use, but this is not a sign of a malfunction. Continue using it as it is.

■

The warranty does not cover damage caused by inserting the UIM into some other types of IC card reader/writer.

■

Always keep the IC portion clean.

■

Use a dry soft cloth such as the one for cleaning glasses to clean the equipment.

■

It is recommended that you make separate notes of the information stored on the UIM and keep such notes in a safe place.

We take no responsibility for any loss of the stored data items.

■

For the environmental protection, bring any unneeded UIMs to a handling counter such as a DoCoMo shop.

■

Avoid using in extremely high or low temperatures.

■

Do not damage, carelessly touch, or short-circuit the IC.

Data might be lost or malfunction may result.

■

Do not drop the UIM or subject it to strong impacts.

Malfunction may result.

■

Do not bend the UIM or place objects on it.

Malfunction may result.

■

Into the FOMA phone, do not insert the UIM with a label or sticker pasted.

Malfunction may result.

■

You may be imposed punishment according to the law and rule (such as the nuisance prevention ordinance) if you use the FOMA phone to give a remarkable nuisance and misdeed to the public.

Notes on handling the UIM

Notes on handling the camera

Please be considerate of the privacy of individuals around you when shooting and sending photos using camera-equipped mobile phones.

Easy Search/Contents/Precautions

■

FOMA phone supports the security function that meets the Bluetooth Specification for the security during connection using Bluetooth. However, the security may not be sufficient depending on the configuration. Take care of the security while making connection using Bluetooth.

■

Even if any leak of data or information occurs while making connection using Bluetooth, we take no responsibility.

■

With the FOMA phone, you can use the following; Headset, Hands-free, Audio, Dial-up Communication, Object Push, and Serial Port. Also, the Audio/Video remote-control might be available depending on the Audio. (Only with compatible Bluetooth devices)

Supported version

Bluetooth Specification Ver. 1.2 compliant

※1

Supported profiles※2(Supported services) HSP

Headset Profile

HFP

Hands-Free Profile

A2DP

Advanced Audio Distribution Profile

AVRCP

Audio Video Remote Control Profile

DUNP

Dial-up Networking Profile

OPP

Object Push Profile

SPP

Serial Port Profile

※

1 The FOMA phone and all Bluetooth function-installed

devices have ensured that they conform to the Bluetooth Specification according to the rules the Bluetooth SIG defines, and are all authenticated. However, operating methods might differ, or data might not be exchanged even when they are connected wirelessly, depending on the features or specifications of connecting devices.

※

2 Standardizes the connecting procedures of Bluetooth per

feature of a device.

■

Radio frequencies

The radio frequencies the Bluetooth function of the FOMA phone uses are as follows:

Notes on using Bluetooth function

2.4FH1

2.4 : Indicates radio facilities that use 2400 MHz frequencies.

FH : Indicates the modulation system is the FH-SS

system.

1 : Indicates that a supposed coverage distance is 10

meters or less.

: Indicates that all radio frequencies 2400 MHz through

2483.5 MHz are used, and that the frequencies for mobile object identifiers shall not be avoided.

■

The FeliCa reader/writer functions on the FOMA phone use very weak radio waves that are license free from radio stations.

■

The FeliCa reader/writer is operated on the 13.56 MHz frequencies. When you use another reader/writer nearby, take enough distance between your FOMA phone and the reader/writer. Further ensure that there are no radio stations that are operated on the same frequencies.

■

Do not use the modified FOMA phone. Using a modified FOMA phone infringes the Radio Law.

The FOMA phones are granted technical regulations conformity certification as the specified radio equipment under the Radio Law and bear a “technical conformity mark

” on the nameplate as evidence of conformity. Unscrewing the FOMA phone and modifying internal components void the technical regulations conformity certification. Do not use the FOMA phone in this state, which infringes the Radio Law.

■

Be especially careful not to operate the FOMA phone during drive.

You are punished for making calls while driving with the FOMA phone in your hand. If this is considered to be of necessity, tell the caller handsfree that you will “redial”, and then park your car in a safe place, and then redial.

■

Use the Bluetooth functions in Japan only.

The Bluetooth functions on the FOMA phone have been authorized in compliance with the radio transmission standards in Japan. You might be imposed punishment if you use it overseas.

■

Use the FeliCa reader/writer functions in Japan only.

The FeliCa reader/writer functions on the FOMA phone have been authorized in compliance with the radio transmission standards in Japan. You might be imposed punishment if you use it overseas.

■

Cautions on Using Bluetooth Devices Bluetooth operates at radio frequencies assigned to the in-house radio stations for a mobile object identifier that have to be licensed and is used in production lines of a factory, specific unlicensed low power radio stations, and amateur radio stations (hereafter, referred to “another radio station”) in addition to scientific, medical, or industrial devices such as microwave ovens.

1. Before using this product, make sure that “another

radio station” is not operating nearby.

2. If radio interference between this product and

“another radio station” occurs, move immediately to another place or stop radio transmission to avoid interference.

3. Contact the following for further details:

DoCoMo Information Center: 0120-005-250 (in English, toll free)

0120-800-000 (in Japanese, toll free)

※

Can be called from mobile phones and PHSs.

Notes on handling the FeliCa reader/ writer

Caution

Easy Search/Contents/Precautions

You have no right to copy, modify, or distribute the contents such as text, images, music, or software programs downloaded from web pages on the Internet, or images shot by the cameras of this product without permission from the copyright holder except for when the copy or quote is for personal use that is allowed by the copyright law. Note that it may be prohibited to shoot or record live performances or exhibitions even for personal use. Make sure that you refrain from shooting portraits of other persons and distributing such portraits over the Internet without consent, as this violates portrait rights.

“FOMA”, “mova”, “PushTalk”, “PushTalkPlus”, “i-mode”, “i-αppli”, “i-

ppliDX”, “i-motion”, “Deco-mail”, “Chaku-motion”, “Chara-den”, “ToruCa”, “mopera”, “mopera U”, “WORLD CALL”, “Dual Network”, “FirstPass”, “visualnet”, “V-live”, “i-Channel”, “DCMX”, “iD”, “Security Scan”, “i-shot”, “i-motion mail”, “i-area”, “Short Mail”, “WORLD WING”, “Public mode”, “DoPa”, “sigmarion”, “musea”, “IMCS”, “OFFICEED”, “2in1”, “Chokkan Game”, and the logos of “FOMA”, “i-mode”, “i-

ppli”, “DCMX”, “iC”, “iD”, “Music&Video Channel”, “HIGH-SPEED” and “WORLD WING” are trademarks or registered trademarks of NTT DoCoMo, Inc.

“Catch Phone (Call waiting service)” is a registered trademark of Nippon Telegraph and Telephone Corporation.

Free Dial logo mark is a registered trademark of NTT Communications Corporation.

McAfee® is registered trademarks or trademarks of McAfee, Inc. and/or its affiliates in the US and/or other countries.

G-GUIDE, G-GUIDE MOBILE and their logos are registered trademarks in Japan of U.S. Gemstar-TV Guide International, Inc. and/or its affiliates.

QuickTime is a registered trademark of Apple Inc., in the US and other countries.

NAVIDIAL and NAVIDIAL logo mark are trademarks of NTT Communications Corporation.

Microsoft®, Windows®, and Windows Vista® are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries.

Windows Media® is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

Powered by JBlend™ Copyright 2002-2006 Aplix Corporation. All rights reserved. JBlend and JBlend-related trademarks are trademarks or registered trademarks of Aplix Corporation in Japan and other countries.

is a registered trademark of FeliCa Networks, Inc.

Intellectual Property Rights

Copyrights and Portrait Rights

Trademarks

The microSD logo is a trademark.

The microSDHC logo is a trademark.

“Multitask” is a registered trademark of NEC Corporation.

QR code is a registered trademark of Denso Wave Inc.

使いかたナビ® is a registered trademark of CANNAC, Inc.

“VIERA” is a registered trademark of Matsushita Electric Industrial Co., Ltd.

Java and Java related trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries.

The Bluetooth word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by NTT DoCoMo, Inc. is under license. Other trademarks and trade names are those of their respective owners.

is a trademark of HI CORPORATION.

The image stabilization technology utilized is PhotoSolid®, a product of Morpho, Inc. PhotoSolid

is the registered trademark of Morpho, Inc. in Japan

and other countries.

Napster is a registered trademark of Napster, LLC. and/or its affiliates in the US and/or other countries.

Other company names and product names described in the text are trademarks or registered trademarks of those companies.

This product contains NetFront Sync Client of ACCESS CO., LTD. Copyright

This product contains IrFront software of ACCESS CO., LTD. Copyright

1996-2007 ACCESS CO., LTD. ACCESS and IrFront are trademarks or registered trademarks of ACCESS CO., LTD. in Japan and other countries.

Contains Flash®Lite™ and Adobe®Reader

technology by Adobe Systems Incorporated. Flash Lite copyright

1984-2007 Adobe Systems Incorporated. All rights reserved. Adobe, Flash, Flash Lite and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.

FeliCa is a contactless IC card technology developed by Sony Corporation.

FeliCa is a registered trademark of Sony Corporation.

Others

Easy Search/Contents/Precautions

Licensed by QUALCOMM Incorporated under one or more of the following United States Patents and/or their counterparts in other nations: 4,901,307 5,504,773 5,109,390 5,535,239 5,267,262 5,600,754 5,416,797 5,490,165 5,101,501 5,511,073 5,267,261 5,568,483 5,414,796 5,659,569 5,056,109 5,506,865 5,228,054 5,544,196 5,337,338 5,657,420 5,710,784 5,778,338

This product contains software licensed complying with GNU General Public License (GPL), GNU Lesser General Public License (LGPL), etc.

For more details, see “readme.txt” in the “GPL

・

LGPL

等について

”

folder on the bundled CD-ROM. (“readme.txt” is only available in Japanese version.)

Advanced Wnn V2 of OMRON SOFTWARE Co., Ltd. is used for conversion methods for Japanese language. “Advanced Wnn V2”

OMRON SOFTWARE Co., LTD. 1999-2007

This product is loaded with Bluetooth® Stack for Embedded Systems Spec 1.2 developed by Toshiba Corp.

This product contains “Sense”, the voice analysis technology of Alegria Corporation for Feel

＊

Talk.

This product is licensed under the MPEG-4 patent portfolio license for the personal and non-commercial use of a consumer to (i) encode video in compliance with the MPEG-4 Visual Standard

(“MPEG-4 Video”) and/or

(ii) decode MPEG-4 Video that was encoded by a consumer

engaged in a personal and non-commercial activity and/or was

obtained from a licensed video provider. No license is granted or implied for any other use. Additional information may be obtained from MPEG LA, LLC. See http://www.mpegla.com.

This product is licensed under the AVC patent portfolio license for the personal and non-commercial use of a consumer to (i) encode video in compliance with the AVC Standard (“AVC

Video”) and/or (ii) decode AVC Video that was encoded by a consumer engaged

in a personal and non-commercial activity and/or was obtained

from a video provider licensed to provide AVC Video. No license is granted or shall be implied for any other use. Additional information may be obtained from MPEG LA, LLC. See http://www.mpegla.com.

This product is licensed under the VC-1 patent portfolio license for the personal and non-commercial use of a consumer to (i) encode video in compliance with the VC-1 Standard (“VC-1

Video”) and/or (ii) decode VC-1 Video that was encoded by a consumer engaged

in a personal and non-commercial activity and/or was obtained

from a video provider licensed to provide VC-1 Video. No license is granted or shall be implied for any other use. Additional information may be obtained from MPEG LA, LLC. See http://www.mpegla.com.

This product is manufactured or sold under license from InterDigital Technology Corporation.

This product uses GestureTek’s technology. Copyright

The abbreviations used for respective operating systems (Japanese version) in this manual are as shown below: Windows Vista is the abbreviation of Windows Vista

(Home Basic, Home Premium, Business, Enterprise, and Ultimate). Windows XP is the abbreviation of Microsoft

Windows® XP

Professional operating system or Microsoft

Windows® XP Home Edition operating system. Windows 2000 is the abbreviation of Microsoft

Windows® 2000

Professional operating system.

This product is protected by certain intellectual property rights of Microsoft Corporation and third parties. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary and third parties.

This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary.

Content providers are using the digital rights management technology for Windows Media contained in this device (“WM-DRM”) to protect the integrity of their content (“Secure Content”) so that their intellectual property, including copyright, in such content is not misappropriated. This device uses WM-DRM Software to play Secure Content (“WM-DRM Software”). If the security of the WM-DRM Software in this device has been compromised, owners of Secure Content (“Secure Content Owners”) may request that Microsoft revoke the WM-DRM Software’s right to acquire new licenses to copy, display and/or play Secure Content. Revocation does not alter the WM-DRM Software’s ability to play unprotected content. A list of Revoked WM-DRM Software is sent to your device whenever you download a license for Secure Content from the Internet or from a PC. Microsoft may, in conjunction with such license, also download revocation lists onto your device on behalf of Secure Content Owners.

Easy Search/Contents/Precautions

Other Options → See page 421

Accessories and Main Options

FOMA P905i Handset (With Warranty and Back Cover P22)

FOMA P905i CD-ROM

The PDF versions of “Manual for PC connection setting” and “Kuten Code List” are included.

Instruction Manual

Quick Manual included (See page 458)

FOMA AC Adapter 01/02 (With Warranty and Instruction Manual)

Desktop Holder P24

(With Instruction Manual)

Battery Pack P15

(With Instruction Manual)

Li-ion

Before Using the Handset

Phone Parts and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Styles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Navigation Displays and Key Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Displaying Description of Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Icons› 30

Private Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Method for Selecting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Using Simple Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

When You do not Remember Key Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Guide› 36

Using UIM (FOMA Card) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Attaching/Removing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Charging FOMA Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Checking Battery Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Battery Level› 44

Turning Power On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Power ON/OFF› 44

Switching to English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Select Language› 45

Executing Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Initial Setting› 45

Setting Date and Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Set Time› 46

Displaying World Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹World Time Watch› 47

Notifying the Other Party of Your Phone Number . . . . . . . . . . . . . . . . .‹Caller ID Notification› 47

Checking Your Own Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Own Number› 48

Before Using the Handset



Earpiece

･

For listening to the other party’s voice



Display

(See page 28)

l

Mail key

･

For showing the Mail menu (See page 187)

･

For operating the function corresponding to the navigation displays (See page 27)

･

For checking new mail messages (See page 183)

m

Menu key/IC Card Lock key

･

For showing the Main Menu (See page 31)

･

For operating the function corresponding to the navigation displays (See page 27)

･

For locking the IC card (See page 230)

r

Clear key

･

For returning to the previous operation

･

For clearing entered text or a phone number

･

For resetting Main Menu (See page 109)

d

Send/Answer key, Hands-free key

･

For making/receiving calls (See page 50 and page 60)

･

For talking with Hands-free (See page 60)

･

For accessing a voice dial entry (See page 94)



Microphone

･

For speaking to the other party



Infrared data port

･

Used for infrared data exchange and the infrared remote-controller. (See page 303 and page 306)



Light sensor

･

For sensing brightness (See page 107)



Inside camera

･

For shooting photos of yourself (See page 133)

･

For catching sight of yourself during a videophone call

o

Command Navigation key

･

For operating functions and menus (See page 27)

Phone Parts and Functions



 























Design of keys is different by the handset body color. Illustrations above are for “Black”/“White” handset.























% &

(

)



■

For inserting or pulling the Flat-plug Earphone/Microphone with Switch (option)

Take hold of the plug and insert or pull it straight into or out. Be careful not to take hold of the cover and plug together when you pull it out.

Plug

Before Using the Handset

i

i-mode key/i-αppli key

･

For showing the i-mode menu (See page 152)

･

For operating the function corresponding to the navigation displays (See page 27)

･

For showing the i-αppli Software List (See page 211)

c

Camera key/One Seg key

･

For activating a camera in “Photo mode” (See page 139)

･

For switching the camera mode while a camera is activated (See page 143)

･

For operating the function corresponding to the navigation displays (See page 27)

･

For starting One Seg (See page 247)

h

Power/End key

･

For ending calls

・

For ending respective functions

･

For turning on the power (for at least one second)/For turning off the power (for at least two seconds) (See page 44)



Numeric keys

･

For entering phone numbers and text

(for at least one second)

For activating Manner Mode (See page 102)

(for at least one second)

For activating Public Mode (Drive Mode) (See page 65)

(for at least one second) For measuring your current location and executing the GPS function (See page 232)

(for at least one second) For switching the backlight on/off (See page 107)

x

Multi key

･

For showing the Multitask menu (See page 333)

･

For showing the display for setting “Switch 3G/GSM” (See page 390)

･

For switching functions, when multiple functions are running (See page 333)



Hook for Horizontal Open Style



Connector terminal

･

For connecting the AC adapter (option), DC adapter (option), or FOMA USB Cable with Charge Function 01 (option)



Call/Charging indicator

･

Flickers for incoming calls/mail and during a call. (See page 111)

･

Lights in red during charging.



Private window

(See page 30)



One Seg antenna

･

For receiving One Seg broadcasting (See page 245)



Outside camera

･

For shooting portraits and/or landscapes (See page 133)

･

For catching sight of persons and/or landscapes during a videophone call



Speakers

･

For sounding ring tone

･

For listening to the other party’s voice through this speaker when Hands-free is activated (See page 60)



FeliCa mark

･

The IC card is mounted.

Use the IC card function placing this mark over the scanning device. You cannot dismount the IC card. (See page 225)



FOMA antenna

The FOMA antenna is embedded in the FOMA phone. Do not cover the antenna with your hand for better communication.



Photo light

･

Flickers when you shoot with a camera.

･

Used for shooting in a dark place. (See page 143)

microSD memory card slot

･

For inserting microSD memory card (See page 293)

Back cover

･

Remove this when attaching/removing the battery pack,

UIM, and microSD memory card. (See page 38, page 41 and page 293)

Do not peel off the black sticker on the back of the back cover. If you peel it off, you might not be able to read and write the IC card.

Charging terminals

Strap hole

PushTalk key

･

For making/receiving PushTalk calls (See page 76 and page 78)

･

For showing the PushTalk Phonebook (See page 79)

･

For activating “MUSIC Player” (See page 323)

Side upper key

･

For scrolling up page by page

<Press and hold for at least one second with the FOMA

phone opened>

･

For activating 2in1 (See page 372)



Side lower key

･

For scrolling down page by page

･

For using Record Message (See page 68)

･

For checking for missed calls and new mail (See page 112)

<Press and hold for at least one second with the FOMA

phone closed>

･

For activating Manner Mode (See page 102)

Earphone/Microphone/AV output terminal

(See page 312 and page 346)

(

One-push open button

(See page 26)

)

Horizontal open lever

(See page 26)

Before Using the Handset

The P905i comes with two styles.

■

Normal Style

You can open the FOMA phone easily by one-push key operation. (One-push Open)

You can open it also manually without using the button.

You need to close the FOMA phone manually. If it does not close, open it fully and then close it.

■

Horizontal Open Style

Hold down the part A and open the display part with the horizontal open lever slid into the direction B. You can watch One Seg programs and use Full Browser in a wide horizontal display.

You can use most functions in Horizontal Open Style even if they are not shown in a wide horizontal display.

If the FOMA phone is not in state of C when you open the display, re-open the FOMA phone after closing it once.

When you open the FOMA phone in Horizontal Open Style, a One Seg program automatically starts in synchronization with the style.

m

SettingsOther settingsWork with style1Seg or OFF

Even when “1Seg” is set, the One Seg program does not start if a display other than the Stand-by display is shown.

Styles

One-push open button

Information

When you open the FOMA phone by pressing the one-push open button, it might not open fully depending on its direction.

When you open the FOMA phone by pressing the one-push open button, be careful not to drop it by its rebound.

When you press the one-push open button in Horizontal Open Style, the FOMA phone will open in Normal Style after it is closed.

Before switching the styles, be sure to completely close the FOMA phone. If you operate the horizontal open lever in Normal Style or with the display part unlatched, malfunction or damage may result.

Work with Style

Horizontal open lever

Before Using the Handset

When you want to execute an operation on the display, press the corresponding key as below.

■

Basic display examples and key assignments

■

Operating Command Navigation key

■

Key operations in Horizontal Open Style

You can operate the keys in the same way as in Normal Style while the vertical display is shown. While the horizontal display is shown, the Navigation icons do not appear and the key operation might differ depending on the function. In this manual, the Command Navigation keys (

ZoXoCoVo

) for the

horizontal display are described corresponding to the horizontal display.

Navigation Displays and Key Operations



Indicates the operation you can perform with the

key.





Indicates the operation you can perform with the

key.





Indicates the operation you can perform with the

key.



Indicates the direction in which you can scroll and select items with the

key.



Indicates the operation you can perform with the

key.





Indicates the operation you can perform with the

key.



・

Moves the cursor or highlighted display up. (Press and hold to scroll continuously.)

・

Scrolls the display while a site or mail text is displayed.

・

Press from the Stand-by display to bring up the Channel List. (See page 170)

・

Converts entered characters to katakana, kanji or other characters. (See page 357)

Right/Redial

・

Moves the cursor to the right.

・

Press from the Stand-by display to bring up the Redial List. Press and hold for at least one second to bring up the Sent Address List. (See page 53 and page 195)

・

Scrolls forward page by page. (Press and hold to scroll continuously.)

・

Moves to the next page while displaying a site.

OK key

・

Fixes the operation.

Left/Received Calls

・

Moves the cursor to the left.

・

Press from the Stand-by display to bring up the Received Call List. Press and hold for at least one second to bring up the Received Address List. (See page 54 and page 195)

・

Scrolls back page by page. (Press and hold to scroll continuously.)

・

Returns to the previous page while displaying a site.

Down

・

Moves the cursor or highlighted display down. (Press and hold to scroll continuously.)

・

Scrolls the display while a site or mail text is displayed.

・

Press from the Stand-by display to bring up the Search Phonebook display. Press and hold for at least one second to store a Phonebook entry. (See page 84 and page 89)

・

Converts entered characters to kanji, katakana or other characters. (See page 357)

+Zo

+Xo

+Co +Vo

Before Using the Handset

Display























 !



"#$















Battery level (estimate) (See page 44)



Radio waves reception level (estimate)

Strong Weak You are out of the FOMA service area or radio

waves do not reach.

During Self Mode (See page 121)



During i-mode (See page 152)

During i-mode communication (See page 152)

During packet communication (The icon differs depending on the communication status.)

During PushTalk communication (See page 76)

You get out of the service area while Network Search Mode is set to “Manual”. (See page 390)



During SSL communication (See page 153)



(white) Unread i-mode mail or an SMS message

exists. (See page 182 and page 207)

(black) The area for i-mode mail and SMS messages

in the FOMA phone is full. (See page 182 and page 207)

The area for SMS messages on the UIM (FOMA card) is full.

(white) Unread mail exists, and the area for SMS

messages on the UIM (FOMA card) is full.

(black) Both the FOMA phone and UIM (FOMA card)

are full.

Area mail exists. (See page 202)



(white) Unread Messages R/F exist. (See page 200)

(black) The area for Messages R/F in the FOMA

phone is full. (See page 200)



(white) i-mode mail is held at the i-mode Center.

(See page 183)

(black) The box for i-mode mail at the i-mode Center

is full. (See page 182)

(white) Messages R/F are held at the i-mode Center.

(See page 200)

(black) The box for Messages R/F at the i-mode

Center is full. (See page 200)

i-mode mail is held at the i-mode Center while Receive Option Setting is set to “ON”. (See page 202)



During a voice call

During a videophone call (64K)

During a videophone call (32K)

During 64K data communication



During measuring the current location (See page 232)

Location Request Menu is set to “ON” or “Permission schedule”, and it is within the validity period. (See page 240)

Location Request Menu is set to “Permission schedule” and it is out of the validity period. (See page 240)



A microSD memory card is inserted. (See page 294)

Data is being read to/written from the microSD memory card.

A write-protected microSD memory card is inserted. (See page 294)

The inserted microSD memory card cannot be used. (See page 294)

A microSD memory card is inserted, and the FOMA USB Cable with Charge Function 01 (option) is connected in microSD Mode. (See page 300)

A microSD memory card is inserted, and the FOMA USB Cable with Charge Function 01 (option) is connected in MTP Mode. (See page 300)



(blue) A Bluetooth device is connected.

(See page 350 and page 351)

(black) A Bluetooth device is connected and power

consumption is low. (See page 350)



During Lock All (See page 120)

During Personal Data Lock (See page 121)

During Keypad Dial Lock (See page 125)

During Secret Mode or Secret Data Only (See page 126)

Before Using the Handset

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

For the horizontal display, icons from  through  appear at the lower left of the display.

The clock at the upper right of the display (at the lower center of the horizontal display) does not appear when icon





is displayed.

When the Stand-by display is shown, the notification icon or desktop icon appears. (See page 112)

During IC Card Lock (See page 230)

Both Keypad Dial Lock and Personal Data Lock are set.

Both Keypad Dial Lock and Secret Mode/ Secret Data Only are set.

Both IC Card Lock and Lock All are set.

Both IC Card Lock and Personal Data Lock are set.

Both IC Card Lock and Keypad Dial Lock are set.

Both IC Card Lock and Secret Mode/Secret Data Only are set.

IC Card Lock, Keypad Dial Lock, and Personal Data Lock are simultaneously set.

IC Card Lock, Keypad Dial Lock, and Secret Mode/Secret Data Only are simultaneously set.



Type of in-use network (See page 387)

You are in the OFFICEED area. (See page 378)



Timer Lock At Close is set. (See page 122)



During Multitask (See page 332)

Multiple functions are activated. (See page 332)

During watching a One Seg program (See page 247)

During music playback (See page 324)

During music pause (See page 324)



During infrared data exchange (See page 303 and page 306)



The FOMA USB Cable with Charge Function 01 (option) is connected in Communication Mode.

The FOMA USB Cable with Charge Function 01 (option) is connected in microSD Mode. (See page 300).

During talk or communication through a USB Hands-free compatible device (See page 60)

A USB Hands-free compatible device is connected. (See page 60)

A USB Hands-free compatible device is connected in microSD Mode. (See page 60)



Vibrator is set. (See page 100)



Ring Volume is set to “Silent” or Mail/Msg. Ring Time is set to “OFF”. (See page 64 and page 101)



During Manner Mode (See page 102)

Remote Monitoring is set to “ON”. (See page 73)



During Public Mode (Drive Mode) (See page 65)



The call cost has exceeded the specified limit. (See page 344)



An alarm is set. (See page 255 and page 336)



A Music&Video Channel program is booked. (See page 316)



Backlight is set to “OFF”. (See page 107)



Side Keys Guard is set to “ON”. (See page 125)

USB Mode Setting is set to “microSD mode”. (See page 300)

USB Mode Setting is set to “MTP mode”. (See page 300)

〜・

Voice mail messages for Number B are held at the Voice Mail Center in Dual Mode of 2in1. (See page 377)

〜・

Voice mail messages are held at the Voice Mail Center. (See page 364)

〜

The number of record messages (See page 67)

〜

The number of videophone record messages (See page 67)

Notification icon

Desktop icon

Before Using the Handset

The symbols at the top of the display (such as , , and ) are called icons. You can check the meanings of the selected icons on the display.

m

SettingsDisplayIconsUse

to highlight an icon.

Various information is displayed on the Private window like the following examples: Press

</>

or p with the FOMA phone closed to display information on the Private window for about 15

seconds.

Information

Some characters and symbols on the display and Private window might be modified or abbreviated. In addition, the Private window is displayed in monochrome.

The color liquid crystal display uses high-precision production technology. The slightest change in the environment or other factors may result in unlit or permanently lit pixels, but this is not a manufacturing defect.

The color display is shown in black and white in this manual, so the color tone of the actual display looks different.

+m-3-6

Icons

Displaying Description of Icons

Private Window

■

When a missed call is found

When the FOMA phone is closed, “Missed call” appears. Press

to display the missed call record. The name is displayed for the missed call coming from the party stored in the Phonebook. When there are multiple missed calls, up to three missed call records are displayed each time you press

If you have received 30 or more incoming calls after a missed call, the missed call record disappears.

Missed call records might not be displayed while another function is activated.

After you display a missed call record, “Missed call” disappears.

■

When a new mail message or Message R/F is received

When the FOMA phone is closed, a Feel＊Mail image is played back, and then “New mail” appears. When you press

, the latest Feel＊Mail image is played back. (For Messages R/F, the Feel＊Mail image is

not played back.) When “Mail” on page 106 is set to “ON”, the received date/time, sender’s address (name), and subject of the mail or the received date/time and subject of the Message R/F are displayed. The sender’s name is displayed for the mail coming from the party stored in the Phonebook. When multiple mail messages or Messages R/F are received, up to three mail messages or Messages R/F appear each time you press

with “New mail”

displayed.

Press< to end the playback of the Feel＊Mail image or to clear the received date/time, and others.

For the mail message and Message R/F to the box or folders with security set, Feel＊Mail images, the received date/time, and others are not played back/displayed.

When a mail message or Message R/F comes in while “Receiving display” is set to “Operation preferred” and a display other than the Stand-by display is shown, “New mail” appears without showing any information.

Depending on the setting for “Auto-display”, “New mail” appears when a Message R/F is received but information is not displayed.

After you display the received date/time and others of the received mail or Message R/F, “New mail” disappears.

When a mail message or Message R/F comes in during a voice call or a videophone call, information is not displayed even when “Receiving display” is set to “Alarm preferred”.

When you set “Secret mail display” to “OFF” and you receive a secret mail message in Normal Mode, a Feel＊Mail image is not played back.

Clock Schedule alarmReceiving a call During a voice callDialing

Before Using the Handset

You can change displayed contents by pressing < while clock is shown.

Press

of the FOMA phone to bring up Main Menu so that you can execute, set, or check respective functions.

Some functions can be selected also by the operation other than pressing m. In this manual, the operation by the easier way is described.

You can also switch to Simple Menu focusing on only basic functions for easy operation. (See page 35)

This FOMA phone supports Kisekae Tool (see page 109). If you use Kisekae Tool to change the design of the Menu display, some menu configurations change according to the usage frequency depending on the type of the menu. Further, some menu numbers that are assigned to the menu items do not apply. In that case, you cannot operate as described in this manual, so you are advised to show Normal Main Menu by “Disp. default MENU” (see page 109), or reset Main Menu by “Reset menu screen” (see page 109). When you set “Menu icon setting” to “

ドコモダケP905i

(DoCoMo-dake_P905i)” of Kisekae Tool, you can restore to normal

menu structure temporarily by selecting “

基本メニュー呼び出し

(Display normal menu)” from main menu item.

■

Scroll Selection

Main Menu is composed of 12 main menu icons indicating each function.

If you select a main menu icon, the Sub-menu Item Selection display appears. If you further select a sub-menu item, the Lower Sub-menu Item Selection display appears.

By repeating selecting, you can set and check the function.

■

Menu Number Selection

You can display some functions by pressing m + the menu number (See page 394).

■

Multitask is Supported

You can simultaneously use some functions in the Main Menu. (See page 332)

In this manual, the description of the command navigation key operation (selection of top/bottom/left/right, and press of

after selecting/entering a function item) is omitted. Scroll selection is explained below using the

example of selecting the function “Quality alarm”:

■

When i-Channel is received

When “i-Channel ticker” on page 106 is set to “ON” and the FOMA phone is closed, tickers flow on the Private window.

Press</> or p to end the tickers’ flow.

Change Clock Display

Method for Selecting Menu

Scroll Selection

Description Example of Steps

Time only Icons and Date/time

Main menu icon

Sub-menu item

Function name of lower sub-menu item

Items which appear on the display

No tone . . . . . . . . .

Does not sound.

High tone

. . . . . . . .

High alarm sounds.

Low tone

. . . . . . . .

Low alarm sounds.

m

SettingsTalkQuality alarmSelect an alarm.

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Before Using the Handset

Select “Settings” from Main Menu. Main Menu at purchase differs depending on the body color. (See page 397)

Select “Talk” from “Settings”.

Select “Quality alarm” from “Talk”.

Select a main menu icon from the menu function

Select a sub-menu item from the menu function

Press

+Mo

to highlight the icon. Press and hold

+Mo

to scroll the icons continuously.

If you have not touched any keys for at least 15 seconds, the Stand-by display returns.

+m +Mo +Oo

Main Menu

Select a desired lower sub-menu item (function)

+Oo+Bo

The highlighted item is the currently selected one.

Press

+Xo

to highlight the item below,

and

+Zo

to highlight the item above.

Press and hold

+Bo

to scroll the items

continuously.

Press

+No

to scroll page by page.

+Oo+Bo

Press

+Xo

to highlight the item below,

and

+Zo

to highlight the item above.

Press and hold

+Bo

to scroll the items

continuously.

When the items are listed over multiple pages, the total number of pages and the current page number are shown at the upper right of the display.

Before Using the Handset

Some menu items have even more detailed menus. The example below shows how to set “Low tone” for “Quality alarm”.

Menu Number Selection is explained below using the following example:

From the Stand-by display, press

m75

Set or check the function

Menu Number Selection

Description Example of Menu Number

+Oo+Bo

The highlighted item is the currently selected one.

Press

+Xo

to highlight the item below,

and

+Zo

to highlight the item above.

Press and hold

+Bo

to scroll the items

continuously.

Bring up the function using the menu number

Menu number

Sounding Alarm when a Line is Likely to be Disconnedted



+m-7-5

-7-5

Before Using the Handset

If you press i when “ ” appears at the lower right of the display, the Function menu including selectable items such as “Save”, “Edit” or “Delete” in each operation appear on the display. The contents of the Function menu depend on the display from which you bring up the Function menu.

When the items are listed over multiple pages, the total number of pages and the current page number are shown at the upper right of the Function Menu display.

In this manual, the operation of the Function menu is described as follows:

An actual operation is done as follows:

Function Menu

Description Example for Function Menu

■

To select items quickly <Direct selection>

Press the numeric key corresponding to the displayed item number.

■

Item scroll

When menu items are listed over multiple pages, you can show the previous/next page by pressing Bo with the uppermost/ lowermost item highlighted. You can press

to scroll through page by page. When / is displayed on the

display, you can scroll through page by page also by pressing

()/c().

For such as lower sub-menu items, depending on the display being shown, you might be able to scroll through page by page also by pressing

instead of No.

Function menu

Operation/Explanation

Delete all You can delete all files.



Enter your Terminal Security CodeYES

Item displayed in the Function menu

Operating procedures after selecting an item in the Function menu

Press+i().

Use

+Mo

to highlight

“Delete all” and press

+Oo

().

Enter your Terminal Security Code and press

+Oo

().

Use

+Bo

to highlight

“YES” and press

+Oo

().

Item number

Before Using the Handset

Simple Menu is a menu focusing on only basic functions for easy operation.

This manual describes the operating procedures in Normal Main Menu only. For how to operate in Simple Menu, see the respective pages of each function.

You cannot use the Multitask function. (See page 332)

You can switch between Normal Main Menu and Simple Menu.

※

Select “YES” to set every item of “Character size” on page 115 to “Large”. Even when you release Simple Menu, either of the

settings does not return. When “Large” has already been set, the confirmation display does not appear.

■

Check box

With the functions you can select multiple items, put a check mark for check boxes to select them. Each time you press

(),

“”

and

“”

switches.

With some functions, you can put or clear check marks at a time by pressing

()



and

selecting “Select all/Release all” or by pressing

(/).

“”

is placed to the selected item depending on the function.

■

After finishing the operation

The Lower Sub-menu Item Selection display is shown. When you press

, the Stand-by display returns (except during

Multitask). The Stand-by display or the former display automatically returns depending on the function.

■

To cancel the operation midway

Press

. The contents of the setting are abandoned and the Stand-by display or the former display returns. The

confirmation display appears asking whether to abandon the setting contents depending on the function. You can press

to return to the previous operation.

■

When the “YES/NO” selection display appears

PressBo to highlight “YES” or “NO”, then press Oo().

Using Simple Menu

Switch to Simple Menu

For Reset Settings

Simple Menu Normal Main Menu

※

From the Stand-by display, press

Before Using the Handset

You can search for the functions you want to know and use, and then check the operating methods. You can execute some functions from “

使いかたナビ

(Guide)”. This function is available in Japanese Mode only.

m

ステーショナリー

(Stationery)使いかたナビ

(Guide)Select an item.

基本の操作

(Basic operations)

. . Displays the basic functions. Go to step 4.

おすすめ機能

(Recommendable functions)

. . . . . . . . . . . . . . . . . . . . . . . . . . . Displays the recommendable functions. Go to step 4.

機能検索

(Function search)

. . . . Searches for a function.

ボイス検索

(Search by voice)

. . . Searches by vocalizing a keyword. Go to step 2 on page 37.

検索履歴

(Search history)

. . . . . . Displays up to 30 search histories. Go to step 4.

Highlight each item and press l( ); then the detailed operating methods are displayed.

The

使いかたナビ

(Guide) display appears also by selecting the

使いかたナビ

(Guide) icon

“ ” pasted on the desktop at purchase.

Select a search method if you select “

機能検索

(Function search)” in step 1.

文字入力キーワード検索

(From your words)

. . . Enter a keyword and retrieve.

索引検索

(From index)

. . . . . . . . . . . . . . . . . . . . Retrieves functions with Japanese syllabic order. You can display the

preceding or following row by pressing

CVo

. Go to step 4.

機能一覧検索

(From Function List)

. . . . . . . . . . Retrieves from the function list. Go to step 4.

Highlight each item and press l( ); then the detailed operating methods are displayed.

If you highlight “

文字入力キーワード検索

(From your words)” and press l( ), select “

文字入力キーワード検索

(From your words)” or “

文字入力のしかた

(How to input words)”.

Configuration of Simple Menu

Phone Mail i-mode Camera

1Seg Tools Settings

Guide

When You do not Remember Key Operation

使いかたナビ

(Guide) display

Before Using the Handset

Enter a keyword.

Up to 50 search results are displayed.

You can enter up to 24 full-pitch/48 half-pitch characters.

Select a functionSelect an item.

機能の説明

(Description)

. . . . . . . . . . .Displays explanations for the function.

操作のしかた

(How to operate)

. . . . . .Displays the operating method.

この機能を使う

(Operate function)

. . .Executes the function. Operate each function.

関連機能

(Relevant function)

. . . . . . . .Displays up to 10 relevant functions. Repeat step 4.

For some functions, press Oo( ) several times for selection.

If you select “

基本の操作

(Basic operations)” in step 1, the description about the function is displayed when that function is

selected. Press

( ) to execute the function.

You can display explanations about the function also by pressing l( ) while highlighting the function.

To delete search history, press i( ) and select “1

件削除

(Delete this)” or “

全削除

(Delete all)”, then select “YES”.

You can search for a function by vocalizing a keyword. Set “Search by voice” of “Read aloud settings” to “ON” to hear voice guidance for operations.

使いかたナビ

(Guide) displayボイス検索

(Search by voice)

You can display the detailed operating methods by pressing l( ) and selecting “

ボイス検索

(Search by voice)” or

“

音声入力のしかた

(How to input voice)”.

Vocalize a keyword when the voice recognition start tone sounds.

Start vocalizing the keyword within seven seconds after the voice recognition start tone sounds. Up to nine detected results are displayed.

You cannot change the sound volume of the voice recognition start tone. It does not sound during Manner Mode.

The keywords you can input by voice are limited to the ones that have been pre-installed to the FOMA phone. If the vocalized keyword is not recognized easily, vocalize a different word.

See page 94 for voice input.

Select a detected resultSelect an item.

このキーワードで検索

(Search from this)

. . . Retrieves with the keyword you have selected. Up to 50 searched results are

displayed. Go to step 4 on page 37.

キーワードの追加

(Add keywords)

. . . . . . . . Add a new keyword. Repeat step 2 and step 3.

Search by Voice

Before Using the Handset

The UIM is an IC card that holds your information such as phone numbers. It can hold data such as Phonebook entries and SMS messages as well. By sharing a UIM, you can operate multiple FOMA phones for multiple purposes. You cannot use the FOMA phone for communication such as voice and videophone calls, i-mode, sending/ receiving mail, or packet communication unless the UIM is inserted. For details on how to use the UIM, refer to the UIM instruction manual. When inserting or removing the UIM, take care not to accidentally touch or scratch the IC.

You need to turn off the power and then remove the battery before you insert the UIM. (See page 41)

■

Inserting

■

Removing

Using UIM (FOMA Card)

Insert/Remove UIM

Pull the claw to pull the tray out.

Pull out the tray straight until it clicks.

Place the UIM on the tray with its IC-side facing up.

Fit the cut corner of the UIM and tray in place.

Push the tray inwards.

Push the tray inwards firmly until it is fixed.

Claw

IC-side is faced up

Cut

Information

Make sure that you insert/remove the UIM with the FOMA phone closed and held in your hand.

Take care not to force the UIM into place because this can break it. And take care not to force the tray into place because it can brake the tray and the guide rail.

Take care not to lose the UIM once you remove it.

When you replace your UIM (except during Omakase Lock), you need to enter the four- to eight-digit Terminal Security Code after turning on the power. When you enter the correct Terminal Security Code, the Stand-by display appears. If you enter the incorrect Terminal Security Code five times in succession, the power turns off. (However, you can turn on the power again.)

Follow step 1 of “Inserting” to pull out the tray and remove the UIM.

■

If the tray is disengaged

Fit and push it straight into the guide rail.

Before Using the Handset

You can set two passwords, PIN1 and PIN2, for a UIM. (See page 118)

The FOMA phone has the UIM restriction function as a security function to protect your data and files. If you obtain data and files by the method below with the UIM inserted, UIM restrictions are automatically set to them.

・

When downloading images or melodies and so on, from sites or Internet web pages

・

When receiving i-mode mail with file attachments

The data or files with the UIM restrictions can be browsed, played back, started, edited, attached to mail, or transferred via infrared rays only when the UIM used for obtaining is inserted. When the UIM used for obtaining the data or files is not inserted, or when another UIM is inserted, these functions are not operable.

In the explanation hereafter, the UIM used to obtain data and files is referred to as “your UIM” and other UIMs as “another person’s UIM”.

When the UIM is not inserted or when another person’s UIM is inserted, the following types of data and files are displayed with the restrictions symbol, “ ”:

・

Videophone record messages

・

Movie memos

・

Melodies

・

Images

・

i-motion movies

・

i-αppli programs

・

Chara-den images・PDF files

・

Kisekae Tool files

・

Chaku-uta®/Chaku-uta Full® music files・Templates

・

Downloaded dictionaries

・

Screen memos

・

Files attached or pasted to i-mode mail in the Inbox

・

Files attached to i-mode mail in the Outbox/Draft (except the data shot or edited with the FOMA phone)

・

Messages R/F with files (melodies or images) attached or pasted

・

Images inserted into Deco-mail text

※

This function applies to the pre-installed i-αppli programs, Chara-den images, Decomail-pictographs, etc. if they are reinstalled (upgraded) from a site.

※

“Chaku-uta” is a registered trademark of Sony Music Entertainment Inc.

The data set with the UIM restrictions appear on the preview display as shown on the right.

About Password of UIM

UIM Restrictions

♪

If the UIM used for obtaining the data or mail messages is inserted, you can browse or play back UIMrestricted data.

♪

Unless the UIM used for obtaining the data or mail messages is inserted, you cannot browse or play back UIM-restricted data.

Your UIM

Another person’s

UIM

Replacing UIMs

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Before Using the Handset

If you use the blue UIM with your FOMA phone, note that following specifications differ from those of the green/ white UIM:

※

WORLD WING is the DoCoMo FOMA international roaming service that enables you to use the current phone number overseas for making and receiving calls using the UIM (green/white) and service compatible mobile phone.

※

You do not need to subscribe to WORLD WING if you have subscribed to the FOMA service after September 1, 2005. If you offered that you did not need WORLD WING at the time you signed up for the FOMA service, or when you have midway

canceled WORLD WING, you are required to take the procedures to newly subscribe to WORLD WING.

※

If you have signed up for the FOMA service before August 31, 2005, and have not yet subscribed to WORLD WING, you are required to subscribe to it.

※

This service is not available with some billing plans.

※

If you lose your UIM (green/white) or have it stolen overseas, immediately contact DoCoMo to take the steps necessary for suspending the use of the UIM. For inquiries, see “DoCoMo Information Center” on the back page of this manual. Note that you

are still charged the call and communication fees incurred after you lose it or have it stolen.

Information

When the UIM restrictions are set for data and files, you cannot set those data and files for the functions such as “Display setting” and “Select ring tone” when another person’s UIM is inserted instead.

If you have set the data and files with the UIM restrictions for the functions such as “Display setting” and “Select ring tone”, these will work with their default settings if you remove your UIM or insert another person’s UIM. If you insert your UIM again, then your settings will be enabled again.

UIM restrictions are not set for the data received using the infrared data exchange function or data transmission (OBEX) function or the still images/moving images shot or edited with the FOMA phone.

Even when another person’s UIM is inserted, data and files set with the UIM restrictions can be moved or deleted.

The settings of the following functions are stored on the UIM:

・

SMS validity period

・

SMS center selection

・

Select language

・

PLMN setting

・

Validating/Invalidating DoCoMo Certificate 1 and user certificate・PIN1 code, PIN2 code・PIN1 code entry set

Differences of UIM (FOMA Card)

Functions

UIM

(blue)

UIM

(green/white)

Reference

Number of digits of the phone number that can be stored in the UIM Phonebook 20 max. 26 max. P.85 Operation of user certificate to use FirstPass Cannot be used Can be used P.165

Use of WORLD WING

※

Cannot be used Can be used P.386 Use of Service Numbers for “DoCoMo repair counter” and “General inquiries <DoCoMo Information Center>”

Cannot be used Can be used P.370

Before Using the Handset

Use the FOMA phone’s dedicated Battery Pack P15.

■

Attaching

■

Removing

Attaching/Removing Batteries

While pressing the “ ” part in the direction A, slide the back cover (2 mm or more) in the direction B to unlock.

With the arrow mark facing up, fit the tab side of the battery pack to the FOMA phone securely, and then push the battery pack into the direction B while pressing it against the direction A.

Slide the back cover in the direction of the arrow and attach it in place.

Arrow mark

While pressing the “ ” part in the direction of A, slide the back cover (2 mm or more) in the direction of B to unlock.

Take hold of the projection of the battery pack to lift it up.

Projection

Information

Make sure that you attach/remove the battery with the FOMA phone closed and held in your hand after you turn off the power. Also, make sure not to press the one-push open button when you attach/remove the battery.

Make sure that the tray for the UIM is not drawn out when attaching the battery. If the tray is drawn out, the battery cannot be attached. Note that if the battery is forcibly attached, the UIM or tray may be damaged.

If you try to force the battery into place, you could damage the charging terminals of the FOMA phone.

For details, refer to the instruction manual for Battery Pack P15.

Before Using the Handset

Use the FOMA phone’s dedicated Battery Pack P15.

Life of battery pack

Battery packs are consumables. The usable time shortens slightly each time they are charged.

When the usable time of the battery pack becomes half the time it was purchased, replacing is recommended because the battery pack is nearing the end of its life. Depending on the use conditions, the battery pack may swell as it nears the end of its life, but this is not a problem.

The life of the battery pack may shorten if you use i-αppli programs, talk on the videophone, watch One Seg programs and so on for a long time during charging.

Charging

For details, refer to the instruction manuals for the FOMA AC Adapter 01/02 (option), FOMA AC Adapter 01 for Global use (option), and FOMA DC Adapter 01/02 (option).

The FOMA AC Adapter 01 supports 100 V AC only. The FOMA AC Adapter 02 and FOMA AC Adapter 01 for Global use support from 100 V AC through 240 V AC.

The shape of the plug for the AC adapter is for 100 V AC (for domestic use). To use the AC adapter that supports from 100 V AC through 240 V AC overseas, you need to have a conversion plug adapter that is compatible with the voltage of the country you stay. Do not use a transformer for overseas travel to charge the battery pack.

Even during charging, you can still answer calls if the FOMA phone is turned on. This will consume the charged amount so that charging will take longer. Also, the standby time or talk time might be shorter if you charge the battery pack with your FOMA phone open.

If you have a long time videophone call during charging, the temperature in the FOMA phone may rise and charging may be suspended. In such a case, wait for a while and try charging again.

Do not watch One Seg programs for a lengthy time during charging as the operating life of the battery might be shortened.

Remove and insert the connector slowly and carefully, without using unnecessary force.

Do not remove the battery pack during charging.

Do not charge for long periods of time (several days) with the FOMA phone turned on.

If you leave the FOMA phone powered on for long periods of time during charging, you may not be able to use the FOMA phone for long duration as expected and the low battery alarm may sound soon, because the FOMA phone receives the power from the battery pack after charging is completed. If this happens, charge the battery pack correctly. When charging the battery pack again, first remove the FOMA phone from the AC adapter (or desktop holder) or DC adapter and then set it again.

Estimated usable time for battery pack

(The usable time for the battery pack varies with the charging time and the remaining life of the battery pack.)

※

The continuous talk time is the estimated time that the FOMA phone can be used for calls when radio waves can be sent and received normally.

※

The continuous standby time is the estimated time when radio waves can be received normally. The standby time could be about half of this estimate depending on the charge level of the battery pack, function settings, other ambient conditions such as temperature, and the status of radio waves in the area (weak or no radio waves, for instance). When you use i-mode communication, the talk/communication time and standby time will be shorter. Further, even if you do not make calls or not execute i-mode communication, the talk/communication time and standby time will be shorter if you watch One Seg programs, compose i-mode mail, start up a downloaded i-αppli program or the i-αppli Stand-by display, execute data communication or Multiaccess, use a camera, play back music, or use Bluetooth connections.

※

The continuous talk time and the continuous standby time may be shortened depending on the network environment in the country you stay.

※

The continuous standby time for standstill is the average number of hours you can use the FOMA phone in standstill status when it is closed and can receive radio waves normally.

※

The continuous standby time for in motion is the average number of hours you can use the FOMA phone in the combined status of “standstill” “moving” and “out of the service area” when it is closed, in an area where it can receive radio waves normally.

※

The One Seg watching time is the estimated time for when radio waves can be received normally with the Flat-plug Stereo Earphone Set P01 (option) connected. The watching time might be shortened depending on the

charge level of the battery pack, function settings,

other ambient conditions such as temperature, and the status of radio waves in the area (weak or no radio waves, for instance).

Estimated time for charging battery pack

※

The charging time is an estimate of time for when empty battery pack is charged with the FOMA phone turned off. The charging time will be longer if you charge the battery pack with the power of the FOMA phone turned on.

Charging FOMA Phone

For environmental protection, bring the exhausted battery pack to an NTT DoCoMo, dealer, or recycle shop.

Li-ion

AC adapter Approx. 130 minutes DC adapter Approx. 130 minutes

Network

Switch 3G/GSM

Continuous standby time Continuous talk time

FOMA/3G

3G In motion: Approx. 420 hours Voice call: Approx. 200 minutes

Videophone call: Approx. 110 minutes

Auto In motion: Approx. 370 hours

Standstill: Approx. 590 hours

GSM

Auto Standstill: Approx. 220 hours Voice call: Approx. 190 minutes

One Seg watching time

Approx. 270 minutes (In ECO mode: Approx. 400 minutes)

Before Using the Handset

■

DC adapter (option) With the DC adapter, you can use a cigarette lighter socket (12 V/24 V) of cars to charge the FOMA phone with the battery pack attached. For details, refer to the instruction manual for the FOMA DC Adapter 01/02.

Charge with AC Adapter and Desktop Holder

Information

If the fuse blows off when charging with the DC adapter, be sure to use a 2A fuse. The 2A fuse is consumables, so purchase at auto parts stores in your neighborhood.

Connect the AC adapter (option) to the desktop holder (option).

Insert the AC adapter’s plug into a power socket.

Put the bottom of the FOMA phone into the stopper of the desktop holder (A) to fit the head to the lock claw, and then depress the FOMA phone until it clicks (B).

Check that the Call/Charging indicator lights in red. When the Call/Charging indicator flickers, dismount the AC adapter and battery pack from the FOMA phone and then re-mount them for charging. If the symptom persists, troubles with the AC adapter, desktop holder or battery pack may be involved, so consult a handling counter such as a DoCoMo shop.

The charging confirmation tone (see page 101) sounds when charging starts and ends. However, it does not sound when the power is off or during Manner Mode or Public Mode (Drive Mode).

Be sure to set the FOMA phone firmly onto the desktop holder. Also, be careful that the connector cap or a commercial strap is not caught between the FOMA phone and desktop holder.

Charging can be done even when the FOMA phone is open.

When charging is completed, hold the desktop holder and lift up the head of FOMA phone to remove.

Unplug the AC adapter from the power socket when you are not going to use it for a long time.

■

Indicator and display during charging and when charging is completed

When the FOMA phone is turned off, “ ” does not appear. If you start charging with the battery flat, the Call/Charging indicator might not light immediately; however, charging itself has started.

Call/Charging indicator

“” display

Charging Lights in red Blinks

Charging completed Off Lights

■

When charging with the AC adapter only

Insert the connector with the engraved surface facing up until it clicks. Pull straight the connector out while pressing the release buttons.

※

Check the facing direction (front or rear) of the AC adapter plug and then insert or pull it horizontally into or out of the FOMA phone. Malfunction could result if you try to pull it forcibly.

Engraved surface

Release buttons

Call/Charging indicator

Desktop Holder P24

Plug in horizontally with engraved side facing down

100 V AC

FOMA AC Adapter 01/02

Stopper

Power socket

Lock claw

AC Adapter’s plug

Connector

Before Using the Handset

When the FOMA phone is turned on, an estimate of the battery level is indicated by the icon.

・

Almost full . . . . . . . . . . . .

・

Getting low . . . . . . . . . . .

・

Almost empty . . . . . . . . .

Charge the battery when it is almost empty.

You can check an estimate of the battery level by the display and sound.

m

SettingsOther settingsBatteryBattery level

The pictograph disappears after about three seconds.

Press and hold

for at least one second.

After the Wake-up display (see page 105) is displayed, the Stand-by display appears.

If you have stored many Phonebook entries or mail messages, it may take a while for the display to appear.

If Set Time is set, the current date and time are shown.

When “ ” is displayed, the FOMA phone is out of the service area or in the place where the radio waves do not reach. Move to a location where “ ” disappears.

If “Starting System Wait a minute” is displayed, wait for a while and then proceed.

Battery Level

Checking Battery Level

Check by Display and Tone

Almost full Getting low Almost empty

Three beeps Two beeps One beep

※

Almost empty. Charge the battery.

■

When the battery is running out

The display on the right appears and the low battery alarm sounds for about 10 seconds. To stop this alarm, press any key other than

and >. About one minute later, the FOMA phone will be

turned off.

During a call, a beeping tone from the earpiece notify you of the low battery. About 20 seconds later your call will be cut and then one minute later the FOMA phone will be turned off.

Power ON/OFF

Turning Power On/Off

Turn Power On

Recharge Battery display

Stand-by display

Before Using the Handset

Press and hold

for at least two seconds.

The exit display appears and the power turns off.

You cannot turn on the power immediately after turning off the power. Wait a few seconds.

m

設定

(Settings)ディスプレイ

(Display)バイリンガル

(Select language)



Japanese (

日本語

) or English (

英語

)

The following functions are different between Japanese display and English display:

If the date and time, Terminal Security Code, Keypad Sound, Caller ID Setting, or Location Request Menu is not set, the Initial Setting display appears when the power is turned on. You can set the initial settings also from each menu function separately.

Turn on the powerYES

When the display for entering your Terminal Security Code, PIN 1 code, or PIN 2 code appears, follow the operation on page 45.

Set the date and time.

You can select “Auto time adjust ON” or “Auto time adjust OFF” for setting the time. (See page 46)

■

When your UIM is replaced (except during Omakase Lock)

Enter the four- to eight-digit Terminal Security Code after turning on the power. When you enter the correct Terminal Security Code, the Stand-by display appears. If you enter the incorrect Terminal Security Code five times in succession, the power turns off. (However, you can turn on the power again.)

■

When “PIN1 code entry set” of “UIM setting” is set to “ON”

Enter the four- to eight-digit PIN1 code after you turn on the power. When you enter the correct PIN1 code, the Stand-by display appears. See page 118 for PIN1 code.

■

When “Auto reset setting” of “Notice call cost” is set to “ON” (except during Omakase Lock)

Enter the four- to eight-digit PIN2 code after you turn on the power. When you enter the correct PIN2 code, the Stand-by display appears. If you press

without entering the correct PIN2 code, “Auto reset setting” is set to “OFF” and the

Stand-by display appears. See page 118 for PIN2 code.

Turn Power Off

Information

Each entry display appears in the order of “PIN1 code” → “Terminal Security Code” → “PIN2 code”.

+m-1-5

Select Language

Switching to English

Functions Japanese English

Info Notice Setting

電子音

(Electrical tone)

ボイス

(Voice)

OFF

Not available

OFF

“Clock”

→

“Day of week” of

Display Setting

Available Not available

使いかたナビ

(Guide)

Available Not available

Voice Guidance Available Not available

Information

When you insert the UIM, the “

バイリンガル

(Select language)” setting is stored on the UIM.

Initial Setting

Executing Initial Settings

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Before Using the Handset

Set your Terminal Security Code.

You can set your Terminal Security Code required for setting functions. (See page 118)

1. Enter “0000”



Enter your new Terminal Security Code (four to eight digits)YES

Set Keypad Sound.

You can set the keypad whether to make a sound. (See page 101)

1. ON or OFF

Set Location Request Menu.

You can set whether to notify your current location for when a GPS location provision request arrives. (See page 240)

Set the size of characters.

You can set the size of characters on the display at a time. (See page 115)

You can select whether to correct the time automatically or set it manually. The time is set/displayed on the 24-hour basis.

m

SettingsClockSet timeAuto time adjust ON or Auto time adjust OFF

Auto time adjust ON

. . . . Corrects the date/time automatically. The setting is completed.

If the time is not automatically corrected such as when “ ” is displayed and the date/time has not been set, the display for manually correcting the time appears. Follow step 2 to set the date/time.

Auto time adjust OFF

. . . Sets the date/time manually.

When “Notice call cost” is set to “ON”, you need to enter your Terminal Security Code.

Enter year, month, date and time.

UseMo to move the cursor and enter numbers by the numeric keys.

To enter one-digit numeral for the date and time, enter two digits beginning with “0” as in “01” through “09”.

Highlight “time zone” and press l( ), to set the time zone. Use Mo to select a region and press

().

Information

When an unset function is found, the Initial Setting display for an unset function appears each time you turn on the power.

The completed settings are valid even when total setting is interrupted by an incoming call or canceled by pressing

-h

-r

midway.

When the power is automatically turned on by alarm notification, the Initial Setting display does not appear even if there is any unset function.

When you finish the initial setting, the confirmation display appears telling that updating software is executed automatically. This display appears only at the first time, and after that, does not appear until you execute Reset Settings or Initialize.

+m-3-1

Set Time

Setting Date and Time

■

About date/time correction function

The time displayed on the FOMA phone is corrected according to the clock information obtained from the network. The time is corrected when you show the Stand-by display with “Auto time adjust ON” set. If you want to set the time with a lag, set the time manually.

Some few second errors might occur. You might not be able to correct the time depending on the radio wave conditions, or the i-

ppli program set for the i-αppli Stand-by display.

When you receive the clock information overseas and the time difference correction information differs from the previously received one, “Time is adjusted” is displayed and the time difference is corrected automatically. Press “OK” to update the time and show Redial, Dialed Calls, Received Calls, sent/received mail messages and others in local time.

When the time difference is corrected overseas, the sub clock (Japanese date/time, etc.) is displayed below the clock on the Stand-by display.

Depending on the networks overseas, the time difference might not be corrected.

Before Using the Handset

You can display the time of the specified area under the Stand-by display clock.

m

SettingsClockWorld time watchON or OFF



Use

to select an area and press

().

You can advance the time displayed for the overseas country you stay and for a region of World Time Watch by one hour.

m

SettingsClockSummer timeON or OFF

You can set the FOMA phone to send your phone number to the called party’s phone when dialing. Your phone number is important information, so take utmost care when notifying your phone number. This function is available only when the other party’s phone supports Caller ID.

You can set whether to notify your caller ID on the network.

m

ServiceCaller ID notificationDo the following operations.

Each time you dial out, you can set whether to notify your caller ID.

Enter a phone number

bring up the detailed display of a Phonebook entry, redial item, dialed call record, or received call record.

()



Notify caller IDDon’t notify or Notify caller (OFF or ON)

To release “Notify caller ID”, select “Cancel prefix”. Whether to notify or not follows the setting for “Activate” of “Caller ID notification”.

Information

Unless Set Time is set, the functions which use the clock such as Schedule do not work correctly. Further, the date/time for redial items and received call records are not stored.

The FOMA phone has an internal backup battery. The set time is stored in the internal backup battery so is kept even when you change the battery. However, the time could be reset if the battery is detached for two or more weeks. In this case, charge the FOMA phone and then set the clock again. Also, when using the FOMA phone for the first time after purchase, attach the battery to the FOMA phone and then charge it. This charges the internal backup battery as well.

The sub clock is not displayed while “Set time” is set to “Auto time adjust OFF” or in Japan.

This function supports clock settings from 00:00 on January 1, 2007 through 23:59 on December 31, 2037.

World Time Watch

Displaying World Time

Information

World Time Watch does not appear when “Display setting” → “Clock” → “Clock display” is set to “OFF”, or when you use the FOMA phone overseas.

Summer Time

Caller ID Notification

Notifying the Other Party of Your Phone Number

+m-1-7

Set Caller ID Notification to Network

Item Operation/Explanation

Activate



ON or OFF

Check setting

You can check the setting contents of “Activate”.

Set Caller ID Notification when Making a Call

Before Using the Handset

You can select whether to notify the other party of your phone number also by entering “186”/“184” before the other party’s phone number.

186→Destination phone number

d

()

Pressl( ) to make a videophone call.

184→Destination phone number

d

()

Pressl( ) to make a videophone call.

Your phone number (own number) is stored on the UIM.

m

PhonebookOwn number

You can press No to switch the tabs.

See page 342 for storing/displaying personal data.

Set “Notify/Not Notify” by Entering “186/184”

To notify your caller ID

Not to notify your caller ID

Information

When you make a call and hear the guidance requesting your caller ID (see page 369), follow the steps of “To notify your caller ID” to enter “186” and redial.

When you make a PushTalk call, “Activate” of “Caller ID notification” or “Notify caller ID” is valid, but “notify/not notify” by adding “186”/ “184” is invalid.

You cannot set “Caller ID notification” while “ ” is displayed.

+m-0

Own Number

Checking Your Own Number

Own Number display

Phone number tab

List tab

Information

In Dual Mode of 2in1, you can switch between Number A and Number B by pressing

+Oo

( ) from the Own Number

display. “ ” appears for Number A, and “ ” appears for Number B.

When you replace a UIM with another one (2in1 contractor → 2in1 contractor) while using 2in1, perform “2in1 function OFF” (see page 373) and then set “2in1 setting” to “YES”, or perform “Auto acquire No. B” (see page 342), to acquire the correct Number B. When you replace a UIM with another one (2in1 contractor

→

2in1 non-contractor), perform “2in1 function OFF” as well to update

the owner’s information to the correct one.

Voice/Videophone Calls

Making Calls/Videophone Calls

About Videophone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Making a Call/Videophone Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Switching between a Voice Call and Videophone Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Using Call Records . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Redial› ‹Dialed Calls› ‹Received Calls› 53

Setting Chaku-moji . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Chaku-moji› 55

Sending Touch-tone Signals Quickly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Pause Dial› 57

International Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹WORLD CALL› 57

Setting for International Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹International Dial Assist› 58

Storing Numbers to be Added to the Beginning of a Phone Number . . . . . . . ‹Prefix Setting› 59

Making a Call with Specified Sub-address . . . . . . . . . . . . . . . . . . . . . . .‹Sub-address Setting› 59

Setting Alarm for Reconnecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Reconnect Signal› 59

Reducing Surrounding Noise to Make Voice Clear . . . . . . . . . . . . . . . . . . . ‹Noise Reduction› 59

Switching to Hands-free . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Hands-free› 60

Using Hands-free Compatible Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹In-Car Hands-free› 60

Receiving Calls/Videophone Calls

Receiving a Call/Videophone Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Switched between a Voice Call and Videophone Call by the Other Party . . . . . . . . . . . . . . . . 62

Setting Response of Key Operation for Answering Incoming Calls . . . . . . ‹Answer Setting› 62

Setting Response for when Opening FOMA Phone during Ringing . . . ‹Setting when Opened› 63

Setting Response for when Closing FOMA Phone during a Call . . . . . ‹Setting when Folded› 63

Adjusting Earpiece Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Volume› 63

Adjusting Ring Volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Ring Volume› 64

When You Cannot or Could not Answer the Call

Putting an Incoming Call on Hold when You cannot Answer at Once. . . . . . . . . . . ‹On Hold› 64

Putting a Call on Hold during a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Holding› 64

Setting Hold Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Set Hold Tone› 65

Using Public Mode (Drive Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Public Mode (Drive Mode)› 65

Using Public Mode (Power Off) . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Public Mode (Power Off)› 66

If You could not Answer an Incoming Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Missed Call› 67

Recording Voice/Video Messages when You cannot Answer the Call

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Record Message Setting› 67

Recording Voice/Video Messages when You cannot Answer the Call during Ringing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Quick Record Message› 68

Playing Back/Erasing Record Messages/a Voice Memo/Videophone Record Messages/Movie Memos

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Play/Erase Messages› ‹Play/Erase Videophone Messages› 68

Making Full Use of Videophone Calls

Using Chara-den . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Useful Functions for Videophone Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Setting Videophone Hands-free. . . . . . . . . . . . . . . . . . . . . . . . . ‹Hands-free with Videophone› 71

Setting Image Quality for Videophone Calls. . . . . . . . . . . . . . . . . . . . . . . . ‹Visual Preference› 71

Changing Image Displays for Videophone Calls . . . . . . . . . . . . . . . . . . . . . . . . ‹Select Image› 71

Redialing as a Voice Call when a Videophone Call cannot be Connected

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Voice Call Auto Redial› 72

Setting for Switching between a Voice Call and a Videophone Call. . . .‹Notify Switchable Mode› 72

Selecting Response to Incoming Videophone Calls during i-mode . . . ‹Videophone while Packet› 72

Connecting FOMA Phone to External Devices to Use Videophone Function . . . . . . . . . . . . . 73

Checking inside the Room when You are Out . . . . . . . . . . . . . . . . . . . . . ‹Remote Monitoring› 73

Voice/Videophone Calls

You and the other party can talk viewing each other’s images.

DoCoMo videophones conform to 3G-324M, standardized by the international standard 3GPP. You cannot connect to the videophone that uses a different format.

3GPP (3rd Generation Partnership Project):

This is the regional standards organization for developing common technical specifications for third-generation mobile telecommunication systems (IMT-2000).

3G-324M:

This is the international standard for the third generation of mobile videophones.

The P905i supports only 64 kbps communication speed of videophone dialing. You can talk but cannot make a videophone call at 32 kbps communication speed.

■

Display during videophone calls

…Receiving image (Image through

the other party’s camera or substitute image)

…Sending image (Image through

your camera or substitute image)

…Call duration …Status

: 64K communicating

: 32K communicating : Voice sending/receiving (gray): Voice sending/

receiving failed

※1

: Image sending/receiving (gray): Image sending/receiving failed

※2

: Camera image sending : Substitute image sending

: Chara-den talking : Hands-free activated : AV output : Bluetooth communicating : Portrait : Close-up : Landscape : Night Mode : Chara-den Whole Action Mode : Chara-den Parts Action Mode : DTMF Transmission Mode

※

1 When voice sending fails, the other party cannot hear your

voice. When voice receiving fails, you cannot hear the other party’s voice.

※

2 When image sending fails, the sending image is not

displayed at the other end. When image receiving fails, the receiving image is not

displayed. When voice or image sending/receiving fails, it does not recover automatically. You need to make a videophone call again.

About Videophone









Enter the other party’s phone number, starting with the city code.

When 27 or more digits are entered, the lower 26 digits only are displayed.

To store an entered phone number in the Phonebook, press

( ). Go to step 2 of “Storing Displayed Phone Number/Mail Address in Phonebook” on page 88.

Even when you are dialing within the same area, you need to enter the city code before the phone number. <Example>

To make calls to mobile phone

To make calls to PHS

Press

or Oo().

“ ” blinks during dialing, and lights during a call.

Press l().

“ ” blinks during dialing and lights during the call.

During a videophone call, you can press

() to display the substitute image at the other party. To resume the image through your camera, press

( ) again.

Press

to end the call after talking.

Making a Call/Videophone Call

City code Local code Phone number



XXXX



XXXX

090−XXXX−XXXX 080−XXXX−XXXX

Other party’s phone number (11 digits)

070−XXXX−XXXX

Other party’s phone number (11 digits)

When Making a Voice Call

When Making a Videophone Call

The digital communication charging starts from this display.

Voice/Videophone Calls

Information

If you hear the guidance requesting your caller ID (see page 369), follow the steps of “To notify your caller ID” on page 48 to enter “186” and redial.

When the Flat-plug Earphone/Microphone with Switch (option) is connected, you can hear the other party’s voice from the earphone. (See page 346)

If you close the FOMA phone during a call, the FOMA phone works in accordance with the setting of “Setting when folded”. (See page 63)

If you switch to Horizontal Open Style during a call, the FOMA phone is set to “No tone”. (See page 63)

You can press numeric keys to send touch-tone signals during a call. During a Chara-den call, you need to switch to DTMF Transmission Mode. (See page 71)

You cannot make a call in Horizontal Open Style. However, when the Flat-plug Earphone/Microphone with Switch (option) is connected, you can make a call in Horizontal Open Style.

In Dual Mode of 2in1, you can make a call after selecting Number A or Number B. (See page 374)

You can make a voice call also by pressing

-d

and then entering the party’s phone number. If you enter a wrong number, press

-h

to clear the display and then redial.

Just after purchase, Hands-free is automatically activated by “Hands-free w/ V. phone” (see page 71). However, Hands-free is deactivated during Manner Mode regardless of “Hands-free w/ V. phone”.

When you make a videophone call with substitute image, note that you will still be charged for the digital communication, not the voice calls.

If you make a videophone call at 110/119/118 from the FOMA phone, it is automatically dialed out as a voice call.

During a videophone call, you can send a Chara-den image to the other party instead of the image through your camera. (See page 69)

The international videophone call is available using the DoCoMo international call service “WORLD CALL”. (See page 57)

■

Display during dialing

The other party’s name and icon will be displayed if the party’s phone number and name are stored in the Phonebook. However, the image will not be displayed, even if it is stored in the Phonebook.

If the same phone number is stored with multiple names in the Phonebook, the name that comes first in the search order (see page 89) is displayed.

The phone number instead of the name will be displayed if the Phonebook entry has been stored as secret data, or if Personal Data Lock is activated.

■

If you entered a wrong phone number

Each time you press

, the digit on the far right is

cleared. If you press and hold

for at least one second,

all the digits are cleared and the Stand-by display returns.

Press No to move the cursor to the digit you want to clear, and then press

to clear it. To clear all the digits on

and to the right of the cursor, press and hold

for at

least one second.

■

If a videophone call could not be connected

The reason why it could not be connected is displayed. (The displayed reason might not be the same as the actual reason depending on the type of the other party’s phone and contract for network services.)

Messages Reasons

Check number, then redial

You have dialed a non-existent phone number.

Busy The other party is busy. (Depending

on the receiver’s phone, this message might be displayed during packet

communication as well.) Busy with packet transmission

The packet communication is

progress at the other end. Out of service area/ power off

The other party’s phone is out of the

service area or turned off. Set caller ID to ON Your caller ID is not notified.

(when dialing “visualnet”) Your call is being forwarded

During forwarding

Redial using voice call

The other party activates Call

Forwarding Service but the forwarding

destination phone does not support

videophone calls. Upper limit has been exceeded Connection failed

The upper limit for the plan with the

limit function (Type Limit, Family Wide

Limit) is exceeded. Please make your call from the i-mode web page

You did not make a videophone call

from the IP (Information Provider) site

among i-mode official sites (at dialing

to V-live). Connection failed Redial after setting “Activate” of

“Caller ID notification” to “ON”.

・

This may appear in the case other than above.

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Voice/Videophone Calls

■

Auto-redialing

If “Voice call auto redial” is set to “ON”, and a videophone call is not connected, a voice call is automatically made.

Videophone calls cannot be connected to the phones that do not support the videophone function, or to the phones that are out of the service area or turned off even if they are videophones. If you have set “Voice call auto redial” to “ON” and attempt to dial a phone that does not have the videophone function, the number will be redialed as a voice call. However, this operation might not work if you call an ISDN-synchronous 64K or PIAFS access point or an ISDN videophone that does not support 3G-324M (as of October 2007), or if you dial the wrong number. Note that you could be charged for the communication.

Once the videophone call has started communications, redialing as a voice call will not be made.

Function Menu while Entering Phone Number

Function menu

Operation/Explanation

Notify caller ID

See page 47.

Prefix numbers

See page 59.

Int’l dial assist

See page 58.

Select image

See page 72.

Multi number

You can select a phone number to be notified to the other party. (See page 372.)

Add to phonebook

See page 87.

Compose message

You can compose a mail message to send to the phone number set as the destination address. Go to step 3 on page 172.

Chaku-moji

See page 55.

You (caller) can switch between a voice call and a videophone call. This function is available for the mobile phones that can switch between a voice call and a videophone call.

When the other party’s phone has a function to switch between the calls, “ ” is displayed on your phone and you can switch from the voice call to videophone call.

During a voice call

c

()



Change

When the other party’s phone has a function to switch between the calls, you can switch from the videophone call to voice call by selecting “CHG to voice call” from the Function menu.

During a videophone call

i

()



CHG to voice callYES

Switching between a Voice Call and Videophone Call

Switch from a Voice Call to Videophone Call

Switch from a Videophone Call to Voice Call

When you select an image to be sent to the other party, select “Select image”. Go to step 2 of “Set by Call” on page 72.

When “Cancel” is selected, the FOMA phone cancels switching and returns to the voice call.

While switching, the voice guidance is played back.

Information

You can switch between a voice call and a videophone call repeatedly.

When i-mode or packet communication is in progress, the communication is disconnected and then the voice call is switched to the videophone call.

Select “NO” on the confirmation display to stop switching and to resume the videophone call.

While switching, the voice guidance is played back.

Voice/Videophone Calls

The FOMA phone can store the other party’s phone number and date/time you have dialed or received. You can call back to the other party.

■

Redial

Up to 30 records of dialed voice calls, videophone calls and PushTalk calls are stored in total, and the older record of dialing to the same phone number is deleted. However, the dialing by PushTalk is retained in Redial separately from that of the voice call or videophone call even if you dial to the same phone number.

■

Dialed Calls

Up to 30 records of dialed voice calls, videophone calls and PushTalk calls are stored in total, and up to 30 records of 64K data and packet communications are stored in total as well. The older records of dialing to the same phone number are also retained.

■

Received Calls

Up to 30 records of incoming voice calls, videophone calls and PushTalk calls are stored in total, and up to 30 records of 64K data and packet communications are stored in total as well. The older records coming from the same phone number are also retained.

When a call is switched between a voice call and a videophone call, the call that is dialed/received first is stored.

When more than 30 calls are dialed, the older records are automatically deleted. Even if you turn off the FOMA phone, call records are not deleted.

In Dual Mode of 2in1, up to 60 redial items, 90 dialed call records, and 120 received call records for Number A and Number B are stored in total.

■

Icons for Redial, Dialed Calls, and Received Calls

When packet communication is in progress at the other end, the message to the effect that the communication cannot be switched is displayed and the voice call continues without switching to the videophone call.

You cannot switch from the voice call to the videophone call while “Multi calling” is displayed during the call if you have signed up for Call Waiting Service.

It takes about five seconds to switch. Switching may take a longer time depending on the radio wave conditions.

Depending on how the caller’s phone is working or on the radio wave conditions, switching between a voice call and videophone call may fail and the connection may be cut off.

If you switch between the voice call and videophone call during a call, the call duration and call cost are counted respectively for the calls. You are not charged while “Changing” is displayed.

You cannot switch between the videophone call and voice call unless “Notify switchable mode” is set to “Indication ON” at the other end. See page 72 for “Notify switchable mode”.

When you switch a videophone call to voice call, Hands-free is deactivated.

Redial Dialed Calls Received Calls

Using Call Records

Information

<>< >< >

※

Dialed and received calls/missed calls of voice call

※

Dialed and received calls/missed calls of videophone call

※

The unchecked missed call icons are highlighted.

Press Vo.

m

PhonebookDialed/recv. calls



Dialed calls

The list for call records is displayed.

For redial items of PushTalk, press

( ) to show the Redial List of the group. Highlight a party and press

to make a PushTalk call. If you do not highlight any party and press

, you can make a

group call.

Press m( ) to display the Sent Address List.

Select a call record.

The detailed display for the call record is displayed.

When the other party is stored in the Phonebook, the phone number, name, and icon are displayed. If the same phone number is stored with multiple names in the Phonebook, the name and icon that come first in the search order (see page 89) are displayed.

※

Dialed and received calls/missed calls of PushTalk

※

Dialed and received group calls/missed group calls of PushTalk

※

Dialed and received calls/missed calls of PushTalk via server’s phonebook

Voice/Video messages are recorded on Record Message

Incoming calls of Remote Monitoring

※

Dialed and received calls/missed calls of international call

※

Dialed and received calls/missed calls of international videophone call

Dialed calls of 64K data communication

※

Received calls/missed calls of 64K data communication

Dialed calls of packet communication

※

Received calls/missed calls of packet communication

Received calls of 64K data communication and packet communication when no external device is connected

Received Chaku-moji message

Records with time difference corrected

Records for Number B (only in Dual Mode of 2in1)

Use Redial/Dialed Calls

When Using Redial

When Using Dialed Calls

For Redial

Voice/Videophone Calls

PressCo.

You can display the Received Call List also by

m

Phonebook



Dialed/recv. callsReceived

calls



All calls or Missed calls.

All calls

. . .All the records including

missed calls

Missed calls

. . .The records of missed calls only In Dual Mode of 2in1, the number of missed calls for Number A and Number B is displayed respectively. (If unchecked missed calls are found, the number of them is displayed.)

For received call records of PushTalk, press

( ) to show the Received Call List of the group

with “

★

” mark added to the caller. Highlight a party and

press

to make a PushTalk call. If you do not highlight

any party and press

, you can make a group call.

Pressm( ) to display the Received Address List.

Select a received call record.

The caller ID is displayed if it was provided; and if this caller has been stored in the Phonebook, the phone number, name, and icon are displayed. If the same phone number is stored with multiple names in the Phonebook, the name and icon that come first in search order (see page 89) are displayed. If there was a call for packet communication, the sender’s access point name (APN) is displayed. When the other party’s phone number is not notified, the reason for no caller ID is displayed.

For missed calls, the ring time is displayed on the right of the received date/time.

When a Chaku-moji message is received, it is displayed.

+m-2-4

Use Received Calls

Received Call List

Detailed Received Call

display

■

To make a call to a displayed redial item, dialed call record, or received call record

Press

to make a voice call. You can make a voice call

also by pressing

( ) from the detailed display.

Press

( ) to make a videophone call and press

to make a PushTalk call.

Information

You can make a voice call to the most recently dialed or received number by pressing

-d

from the Stand-by

display and then

+No

When you make/receive a call with an additional number of Multi Number, the stored name for the additional number is displayed below the phone number on the detailed display. If you store a phone number for “Number setting” of “Multi number”, the phone number is displayed as well.

The dialed call records of 64K data communication are stored only when the FOMA USB Cable with Charge Function 01 (option) is connected.

Even if you make a voice call (or videophone call) to the phone number in a received call record with a Chaku-moji message displayed, the received Chaku-moji message is not sent.

When a call comes in from a party who uses a dial-in phone number, a different phone number might be displayed.

Function Menu while Redial/Dialed Calls/Received Calls is Displayed

Information

Function menu

Operation/Explanation

Notify caller ID

See page 47.

Prefix numbers

See page 59.

Int’l dial assist

See page 58.

2in1 dial

You can select a phone number to be notified to the other party in Dual Mode of 2in1. (See page 374)

Multi number

You can select a phone number to be notified to the other party. (See page 372)

Chaku-moji

See page 55.

Character size

You can switch the character size for the list between Large and Standard.

The setting here applies to “Dialed/recv. calls” of “Character size”.

Add to phonebook

See page 87.

You can store the phone number in the Phonebook also by pressing

() from the detailed display. Go to step 2 of “Storing Displayed Phone Number/Mail Address in Phonebook” on page 88.

Feel＊Talk

See page 110.

Ring time

[Received Call List only]

You can display the ring time for missed calls. Even if you have set “Missed calls display” of “Ring time” to “Not display”, the missed calls which stopped ringing within the ring start time and their ring times are displayed.

Add desktop icon

See page 114.

Compose message

You can compose a mail message to send to the phone number set as the destination address. Go to step 3 on page 172.

Compose SMS

You can compose an SMS message to send to the phone number set as the destination address. Go to step 3 of “Composing SMS Messages to Send” on page 206.

Voice/Videophone Calls

When making a voice call or videophone call, you can send your text message to tell the subject during calling.

For details on Chaku-moji or compatible models, refer to DoCoMo web page or “Mobile Phone User’s Guide [Network Services]”.

The sending end is charged, but the receiving end is not charged.

Sent address

[Redial/Dialed Calls only]

See page 195.

Received address

[Received Calls only]

See page 195.

Delete this



YES

Delete selected



Put a check mark for redial items, dialed call records, or received call records to be deleted

l

()



YES

Delete all



Enter your Terminal Security CodeYES

Select image

See page 72.

Store in P-Talk PB



YES

Store P-Talk group



Select a group.

When members who are not stored in the PushTalk Phonebook are found, the confirmation display appears asking whether to store them.



Enter a group name.

You can enter up to 16 full-pitch/32 half-pitch characters.

Information

Delete this> <Delete selected> <Delete all>

If you execute “Delete all” from the Function menu of Redial/ Dialed Calls, all records in both Redial and Dialed Calls are deleted. Even if you execute “Delete this” or “Delete selected” of Redial, the records are not deleted from Dialed Calls and they are retained. To delete the dialed call records, delete them from the Function menu while “Dialed calls” is displayed.

Store in P-Talk PB>

You cannot store from the call record for the party who is not stored in the Phonebook.

Store P-Talk group>

You cannot store in a PushTalk group unless all the members are stored in the FOMA phone’s Phonebook.

Chaku-moji

Setting Chaku-moji

Function menu

Operation/Explanation

You can store up to 10 Chaku-moji messages in the Message List.

m

ServiceChaku-mojiCreate message



Highlight <Not stored> and press l()



Enter a message.

To edit a stored message, highlight it and press l().

You can enter up to 10 characters regardless of whether they are pictographs, symbols, or full-pitch/half-pitch characters.

Enter a phone number

bring up the detailed display of a Phonebook entry, redial item, dialed call record, or received call record.

()



Chaku-moji



Do the following operations.

■

When a Chaku-moji message is received

A Chaku-moji message is displayed below a caller. The Chaku-moji message is stored in Received Calls as well.

The Chaku-moji message is displayed only during ringing. It is not displayed during a call.

Even when a Chaku-moji message comes in within the ring start time set by “Ring time”, it is received and recorded in Received Calls.

The Chaku-moji message is displayed on the Private window when “Chaku-moji” of “Called” on page 106 is set to “ON”.

The Chaku-moji message is not displayed during Lock All, Omakase Lock, or Personal Data Lock. However, you can check the Chaku-moji message from Received Calls after the lock is released.

Store Chaku-moji Messages

Make a Call with a Chaku-moji Message

Function menu

Operation/Explanation

Create message

You can create a Chaku-moji message just before dialing.



Enter a message.

You can enter up to 10 characters regardless of whether they are pictographs, symbols, or full-pitch/half-pitch characters.

The Chaku-moji message created using this function is not stored in the Message List.

Select message

From the Message List, you can select the stored Chaku-moji message.



Select a message.

Sent messages

From the Sent Message List, you can select a Chaku-moji message to be sent. Up to 10 sent Chaku-moji messages only are stored in the Sent Message List. If you send the same Chaku-moji message, the older one is deleted. When the number of sent Chaku-moji messages exceeds 10, the messages are deleted from the oldest one.



Select a sent message.

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Voice/Videophone Calls

Press

or Oo().

Pressl( ) to make a videophone call.

The Chaku-moji message being sent is displayed during dialing.

Up to 10 sent Chaku-moji messages are stored in Sent Messages, and you can check for the other party’s phone number and the date/time the Chaku-moji messages were sent. Older messages sent to the same phone number are also retained.

In Dual Mode of 2in1, up to 10 records for Number A and Number B can be displayed in total.

m

ServiceChaku-mojiSent messages

. . .Chaku-moji message

successfully sent

. . .Chaku-moji message

unsuccessfully sent

. . . . . .Chaku-moji message

for Number B (only in Dual Mode of 2in1)

When the transmission result is not displayed, “ ” or “ ” is not displayed.

Depending on the radio wave conditions, the transmission result might not be displayed correctly.

Select a sent message.

When the other party’s phone number is stored in the Phonebook, the phone number, name, and icon are displayed.

Information

When a Chaku-moji message has arrived at the other party’s phone, “Transmission completed” is displayed, and you are charged a transmission fee.

When a Chaku-moji message does not arrive at the other party’s phone such as when the other party’s phone is not a Chaku-moji compatible mobile phone or the call is not allowed by “Message disp. settings” at the receiving end, “Transmission failed” is displayed. In this case, you are not charged a transmission fee.

Depending on the radio wave conditions, the transmission result may not be displayed at the sending end even if a Chaku-moji message has arrived at the other party’s phone. In this case, you are charged a transmission fee.

Even if you make a call sending a Chaku-moji message, the Chaku-moji message is not displayed and you are not charged a transmission fee (the call is not recorded in Received Calls at the receiving end) when the other party’s phone is out of the service area, turned off, during Public Mode (Drive Mode), or the ring time for Record Message Setting is set to zero seconds. Also, the transmission result is not displayed at the sending end.

When a videophone call is not connected and automatically dialed as a voice call, the Chaku-moji message is resent as well.

Chaku-moji does not support PushTalk.

You cannot send/receive Chaku-moji messages overseas.

Detailed Sent Message

You can set how incoming Chaku-moji messages are displayed.

m

ServiceChaku-moji



Message disp. settingsSelect an item.

Display all messages

. . .Displays Chaku-moji messages from all callers.

Numbers stored in PB

. . .Displays Chaku-moji messages only from the callers

stored in the Phonebook.

Calls with callerID

. . .Displays Chaku-moji messages only from the caller

notifying his/her phone number.

Hide all messages

. . .Does not display Chaku-moji messages.

You can set how your FOMA phone works for incoming Chaku-moji messages for when “Setting when opened” is set to “Answer”.

m

ServiceChaku-moji



Prefer Chaku-mojiON or OFF

. . . . .Does not answer by opening the FOMA phone

during ringing, so you can check a Chaku-moji message.

OFF

. . . .Answers by opening the FOMA phone during

ringing.

Function Menu while Detailed Sent Message is Displayed

Function menu

Operation/Explanation

Store

You can store a sent Chaku-moji message in the Message List.



You can store also by pressing l().

Delete this



YES

Delete all



Enter your Terminal Security CodeYES

Message Display Settings

Information

When you set to “Numbers stored in PB”, you cannot receive Chaku-moji messages from the callers stored in the Phonebook B in A Mode of 2in1 (and vice versa).

Prefer Chaku-moji

Voice/Videophone Calls

You can send touch-tone signals from your FOMA phone to use services such as reserving tickets, checking bank balance, etc.

You need to store a number string to be sent as a touch-tone signal in the Pause Dial List. If you have inserted a pause (p), you can send a number string breaking at the point where the pause is inserted.

m

SettingsOther settingsPause dial

l

()

When a number string is already stored, it is displayed.

To delete a stored pause dial, press i( ) and select “Delete”, then select “YES”.

Enter a number string.

Enter the pause (p) by pressing and holding

for at

least one second.

You can use only

through

9,s,a

enter a number string and the pause (p).

You can enter up to 128 digits.

You cannot enter a pause (p) at the beginning and end of a number string, or enter it consecutively.

m

SettingsOther settingsPause dial

Oo

()



Enter a phone number

d

or Oo()

A voice call is made. Once the line is connected, a number string stored in Pause Dial is displayed up to the first pause (p).

When the other party’s phone number is stored in the Phonebook, you can retrieve it selecting from the Search Phonebook display by pressing

You can search for the phone number also from Received Calls by pressing

or from Redial by

pressing

Check that the line is connected

d

or Oo()

A number string up to the first pause (p) is sent, and a number string up to the next pause (p) is displayed. A number string up to the pause (p) is sent each time you press

or Oo(). When you have finished sending the last number, the “Talking” display appears.

To send multiple pieces of a number string at a time, press and hold

for at least one second, and select

“Send at one time”.

+m-8-4

Pause Dial

Sending Touch-tone Signals Quickly

Store Pause Dial

Send Pause Dial

WORLD CALL is the international call service available from DoCoMo mobile phones. When you have signed up for FOMA service, you have contracted to use “WORLD CALL” (except those who have applied not to use it).

You can call about 240 countries and regions.

The WORLD CALL charges are added to your monthly FOMA bill.

The application/monthly fee is free of charge.

Changes in procedures for international call “My Line” service is not available for mobile communications such as mobile phones, so cannot be used with WORLD CALL. However, in conjunction with the launch of “My Line” service, the dialing procedure for international calls from mobile phones has changed. Note that the old way of dialing (the way without “010” from the following operation) no longer works.

The service is not available with some billing plans.

Contact “DoCoMo Information Center” on the back page of this manual for inquiries about WORLD CALL.

When using international carriers other than DoCoMo, contact them.

Information

During a call, you can send a number string also by displaying the Function menu of the Pause Dial display.

Some devices on the receiving end cannot receive signals.

You cannot send a number string with pauses during a videophone call.

WORLD CALL

International Calls

■

About international videophone calls

You can make international videophone calls to the other party who uses a specific 3G mobile phone overseas. Press

( ) instead of

or Oo( ) in the steps of “Enter a Phone Number to Make an International Call”. (See page 58)

For the information about connectable countries and telecommunications carriers, refer to the DoCoMo Global Service web page.

Images sent from the other party may blur on your FOMA phone or you may not be able to connect, depending on the other party’s phone used for the international videophone call.

Voice/Videophone Calls

Enter numbers in order of 009130→010

→

country code→area code (city code)

→

destination phone number

d

or Oo()

When the area code (city code) begins with “0”, enter it except for the “0”. However, include “0” when making a call to some countries or regions such as Italy.

Press l( ) to make an international videophone call.

When you enter a phone number for dialing or storing it in the Phonebook, press and hold

for at least one second to enter “+”. You can use “+” to make international calls without entering an international call access code such as 009130-010.

If you set “Auto assist setting” of “Int’l dial assist” to “ON”, an international call access code of “IDD prefix setting” is automatically entered.

(for at least one second)



Enter numbers in order of country code

→

area code (city code)→destination phone

number

d

or Oo()



Dial

When the area code (city code) begins with “0”, enter it except for the “0”. However, include “0” when making a call to some countries or regions such as Italy.

Press l( ) to make an international videophone call.

When you select “Dial with orig. No.”, you can make a call without adding an international call access code.

You can make a call adding a country code or international call access code to a phone number. (Except for some countries or regions, if the phone number starts with “0”, the “0” at the beginning is automatically deleted.)

Enter a phone number

bring up the detailed display of a Phonebook entry, redial item, dialed call record, or received call record.

()



Int’l dial assist



Select a country nameSelect a name

d

or Oo()

Press l( ) to make an international videophone call.

When the beginning of the phone number is “+”, you can select only an international call access code.

When “Japan” is selected as a country name, the display for selecting a name is not displayed.

Enter a Phone Number to Make an International Call

Use “+” to Make an International Call

International Dial Assist

You can set whether to replace “+” at the beginning of a phone number with an international call access code for when you make an international call from Japan.

m

SettingsNetwork setting



Int’l dial assistAuto assist setting



ON or OFFSelect a country name



Select a name.

When no country code or international call access code is stored, the confirmation display appears asking whether to store it. Select “YES” and go to step 2 of “Country Code Setting” on page 58 for a country code, and go to step 2 of “IDD Prefix Setting” on page 58 for an international call access code.

You can store up to 27 country codes to be added for making international calls from overseas.

m

SettingsNetwork setting



Int’l dial assistCountry Code set.



Highlight <Not recorded> and press

().

If you select a stored country name, you can check the stored contents.

Enter a country name Enter a country code.

You can enter a country name of up to 8 full-pitch/16 half-pitch characters.

You can enter a country code of up to 5 digits. But you cannot use #,

, and +.

You can store up to three international call access codes to be added to the beginning of a phone number for making an international call.

m

SettingsNetwork setting



Int’l dial assistIDD prefix setting



Highlight <Not recorded> and press

().

If you select the stored item, you can check the stored contents.

Enter a nameEnter an international call access code

You can enter a name of up to 8 full-pitch/16 half-pitch characters.

You can enter an international call access code of up to 16 digits.

International Dial Assist

Setting for International Calls

Auto Assist Setting

Country Code Setting

IDD Prefix Setting

Voice/Videophone Calls

You can store prefix numbers such as international call access codes or “186”/“184” and add them to the phone number for dialing. You can store up to seven prefix numbers.

m

SettingsNetwork setting



Prefix settingHighlight <Not recorded>

and press

().

If you select a stored prefix, you can check the stored contents.

To delete a stored prefix, press i( ) and select “Delete this” or “Delete all” then select “YES”. If you select “Delete all”, you need to enter your Terminal Security Code.

Enter a nameEnter a prefix number.

You can enter a name of up to 8 full-pitch/16 half-pitch characters.

You can enter a prefix number of up to 16 digits. The keys for entry are limited to

through

9,s

and

You can add a prefix number to the beginning of phone number when you make a call.

Enter a phone number

bring up the detailed display of a Phonebook entry, redial item, dialed call record, or received call record.

Function Menu while Country Code Setting/IDD Prefix Setting is Displayed

Function menu

Operation/Explanation

Edit

Go to step 2 of “Country Code Setting” on page 58 for Country Code Setting, and go to step 2 of “IDD Prefix Setting” on page 58 for IDD Prefix Setting.

You can edit the item also by pressing

().

Delete this



YES

Delete all



Enter your Terminal Security CodeYES

Information

Delete this

> <

Delete all>

You cannot delete the country code or international call access code set by “Auto assist setting”.

Prefix Setting

Storing Numbers to be Added to the Beginning of a Phone Number

Prefix Numbers

()



Prefix numbers



Select a name

d

or Oo()

Press l( ) to make a videophone call and

press

to make a PushTalk call.

For making a PushTalk call, adding a prefix number such as “186” or “184” to the beginning of the phone number is disabled.

You can set whether to regard the numbers after “:” of a phone number as a sub-address to access the specified phones or data terminals.

The sub-address is a number assigned to identify each ISDN terminal connected to an ISDN line. It is also used for selecting contents on “V-live”.

m

SettingsOther settings



Sub-address settingON or OFF

You can set an alarm that sounds until a voice call, videophone call, or PushTalk communication is reconnected after disconnected owing to bad radio wave conditions.

m

SettingsTalkReconnect signal



Select an alarm.

m

SettingsTalkNoise reduction



ON or OFF

Sub-address Setting

Making a Call with Specified Sub-address

Information

Even if you set “Sub-address setting” to “ON”, “:” at the top of phone numbers and “

” immediately after the prefix number or “186”/“184” are not regarded as sub-address mark-off symbols.

+m-7-7

Reconnect Signal

Setting Alarm for Reconnecting

Information

The reconnectable time differs depending on the usage status and radio wave conditions. An estimate is about 10 seconds and the call charge is applied also for that duration.

While you are disconnected, no sound is transmitted to the other party.

+m-7-6

Noise Reduction

Reducing Surrounding Noise to Make Voice Clear

Voice/Videophone Calls

When you switch to Hands-free, sound such as the other party’s voice is audible over the speaker.

During a call

d

When Hands-free is activated, “ ” is displayed.

You can activate/deactivate Hands-free during a call. For videophone calls and PushTalk calls, you can activate/deactivate also during dialing or connecting.

Press

again to deactivate Hands-free.

The sound volume during a Hands-free call follows the setting specified by “Volume” (earpiece volume).

You can switch to Hands-free even during Manner Mode. Also, you will still hear voice through the speaker even when you activate Manner Mode during a Hands-free call.

You can make or receive voice calls from a Hands-free compatible device such as In-Car Hands-Free Kit 01 (option) or a car navigation system by connecting with your FOMA phone. You can connect your FOMA phone to a Hands-free compatible device using two ways of connections as follows:

Connect using a cable (USB connection):

To use/charge via the In-Car Hands-Free Kit 01 (option), you need to have the FOMA In-Car Hands-Free Cable 01 (option).

Connect using Bluetooth (wireless):

To connect to a Bluetooth compatible Hands-free device, you need to register and connect it to the FOMA phone.

※

For how to operate Hands-free compatible devices, refer to the respective instruction manuals.

Hands-free

Switching to Hands-free

Information

While the Flat-plug Earphone/Microphone with Switch (option) is connected, you cannot hear voice through the speaker even if you switch to Hands-free.

Keep the FOMA phone well away from your ear during a Hands-free call. Otherwise you could affect or damage your hearing.

Talk into the FOMA phone within a distance of about 50 cm.

In-Car Hands-free

Using Hands-free Compatible Devices

Information

To connect using a cable (USB connection), set “USB mode setting” to “Communication mode”.

“ ” appears while you are talking or communicating using a USB Hands-free compatible device.

When you receive a call, the ring tone sounds and the Call/Charging indicator flickers.

To vibrate the FOMA phone for incoming calls, set “Phone” or “Videophone” of “Vibrator” to other than “OFF”.

When receiving a videophone call, “Incoming V.phone” is displayed.

“ ” is displayed at the upper right of the phone number for incoming international calls.

“ ” might appear while the FOMA phone is connected to a USB Hands-free compatible device, and “ ” while “USB mode setting” is set to “microSD mode”, depending on the Hands-free device connected.

The display or ring tone for incoming calls follows the settings of the FOMA phone.

When the sound is set to output from a Hands-free compatible device, the ring tone sounds from that device even when Manner Mode is activated or “Ring volume” of the FOMA phone is set to “Silent”.

The receiving operation in Public Mode (Drive Mode) works in accordance with the “Public (Drive) mode” setting.

The receiving operation while Record Message is activated works in accordance with the “Record message setting” setting.

When the sound is set to output from the FOMA phone, the FOMA phone works in accordance with “Setting when folded” if it is closed during a call. When the sound is set to output from a Hands-free device, the communication state does not change regardless of “Setting when folded” even if you close the FOMA phone.

Receiving a Call/Videophone Call

Information

Chaku-moji message

(See page 55)

Voice/Videophone Calls

Press

or Oo( ) to answer the call.

Press

or Oo()

to answer the

videophone call.

You can send the image through your camera to the other party. Press

( ) to take a videophone call, and the substitute image is sent to the other party. (Substitute image answering)

Press m during a call to switch between the image through your camera and substitute image for sending to the other party.

Press

to end the call after talking.

For Answering a Voice Call

For Answering a Videophone Call

Information

If you close the FOMA phone during a call, the FOMA phone works in accordance with the setting of “Setting when folded”. (See page 63)

You might hear beeps (in-call ring tone) during a call. If you have signed up for any of Voice Mail Service, Call Waiting Service, or Call Forwarding Service and set “Arrival call act” to “Answer”, the beeps (in-call ring tone) will sound for another incoming call, enabling you to do the following operations: Voice Mail Service . . . Transfer the call to the Voice Mail Service Center.

(See page 365) Call Waiting Service . . . Put your current call on hold and answer the incoming

call. (See page 366) Call Forwarding Service . . . Transfer the call to the registered forwarding

destination. (See page 368)

You can set “Reject unknown” not to accept calls from the phone numbers not stored in the Phonebook.

You cannot answer a call in Horizontal Open Style. However, when the Flat-plug Earphone/Microphone with Switch (option) is connected, you can answer a call in Horizontal Open Style.

When “Answer setting” is set to “Any key answer”, the call is placed on hold if you answer the call by pressing

with the FOMA phone closed. If you have set “Setting when folded” to “No tone” or “End the call”, the other party hears nothing, and if you have set “Setting when folded” to “Tone on”, the call hold tone is played back. You can start talking by opening the FOMA phone.

Just after purchase, Hands-free is automatically activated during a videophone call as “Hands-free w/ V. phone” has been set to “ON”. (See page 71) However, Hands-free is deactivated during Manner Mode regardless of “Hands-free w/ V. phone”.

Even if Call Forwarding Service is set to “Activate”, the call is not forwarded unless the forwarding destination is a phone compatible with the videophone conforming to 3G-324M (see page 50). Check the phone you are forwarding the call to and then activate the service. The videophone caller does not hear the guidance to the effect that the call is forwarded. (The message to the effect that the call is to be forwarded appears, depending on the receiver’s FOMA phone.)

If a videophone call comes in from the phone number to be rejected by Nuisance Call Blocking Service, the video guidance for Call Rejection is played back and the call is disconnected.

You can send a Chara-den image to the other party instead of the image through your camera. (See page 69)

■

Display for incoming calls

When a caller’s phone number is provided

If you store the caller’s name, phone number, and image in the Phonebook, the name, phone number, and icon (or image) are displayed.

If the same phone number is stored with multiple names in the Phonebook, the name that comes first in the search order (see page 89) is displayed.

The phone number but not the name is displayed during Personal Data Lock.

For a forwarded call, the forwarder’s phone number is displayed below the caller. (It might not be displayed in the case of some forwarders.)

When you receive a call to an additional number of Multi Number, the stored name for the additional number is displayed below the caller. (With a forwarded call, you can press

( ) to switch to display of the forwarder.)

When a caller’s phone number is not provided

The reason for no caller ID is displayed. (See page 128)

Information

Voice/Videophone Calls

When you have set “Notify switchable mode” to “Indication ON”, the caller (the other party) can switch between a voice call and videophone call.

You (receiving end) cannot switch between a voice call and videophone call.

The display for switching to a videophone call appears during a voice call.

YES

. . .Sends the image through

your camera to the caller.

. . . .Sends a pre-installed

substitute image to the caller.

While switching, the message to that effect is displayed and the voice guidance is played back.

When the caller (the other party) switches a videophone call to a voice call, the message telling that the call is being switched appears, the voice guidance is played back, and then the call is switched to a voice call.

Function Menu while a Call is Ringing

Function menu

Operation/Explanation

Call rejection

You can disconnect the call without answering.

Call forwarding

See page 368.

Voice mail

See page 365.

Switched between a Voice Call and Videophone Call by the Other Party

Switched from a Voice Call to Videophone Call by the Other Party

Switched from a Videophone Call to Voice Call by the Other Party

You can set to start talking (Any key answer) or to stop the ring tone (Quick silent) by pressing a key besides

Oo,d,m

(for videophone call) or p (for

PushTalk call) for when a call or PushTalk call comes in.

m

SettingsIncoming call



Answer settingSelect a key operation.

Any key answer

You can start talking by pressing any key shown below:

When receiving a videophone call, you can start talking by pressing

Oo,d

or m.

Quick silent

The following are the keys you can press to stop the ring tone, vibrator or voice guidance: When “Setting when opened” is set to “Keep ringing”, you can open the FOMA phone in Normal Style to stop the ring tone, vibrator or voice guidance. Even if you stop it, the other party hears a calling tone.

After you stop the ring tone, vibrator or voice guidance by the key operation above, you can press

Oo,d

(for videophone call), or press p (for PushTalk

call) to start talking.

OFF

You can start talking by pressing a key shown below:

※

1 You can start talking also by pressing l when five

record messages have already been recorded.

※

2 While “ ” is displayed, you cannot start talking

or stop the ring tone, vibrator or voice guidance.

+m-5-8

Answer Setting

Setting Response of Key Operation for Answering Incoming Calls

Voice

call

※1

Oo,d,0

through

9,a

s,r,m,c

※2

,No,

PushTalk call

Oo,d,p,0

through

a,s,r,l,c,Bo,<

Voice call

through

9,a,s,r

m,c

※2

,No,

Videophone call

through

9,a,s,r

※2

,No,

PushTalk call

through

9,a,s,r

l,c,Bo,<

Voice call

Oo,d

Videophone call

Oo,d,m

PushTalk call

Oo,d,p

Voice/Videophone Calls

m

SettingsIncoming call



Setting when opened



Select an incoming type



Keep ringing or Answer

m

SettingsTalkSetting when folded



Phone/VideophoneSelect an item.

No tone

. . . . . . The voice is muted. The hold tone does

not sound. The setting is completed.

Tone on

. . . . . . The other party hears the hold tone set

for “Holding tone” of “Set hold tone” while the FOMA phone is closed.

End the call

. . . The call is finished. This is the same

operation as pressing

during a

call. The setting is completed.

Speaker ON or Speaker OFF

Speaker ON

. . . . The hold tone sounds from the

speaker.

Speaker OFF

. . . The hold tone does not sound from the

speaker.

m

SettingsTalkSetting when folded



PushTalkSpeaker call or End the call

Information

While the Flat-plug Earphone/Microphone with Switch (option) is connected, you can press the switch to start talking, regardless of “Answer setting”. (See page 347)

Setting when Opened

Setting Response for when Opening FOMA Phone during Ringing

Information

If you receive a videophone call with “Answer” set, the still image set for “Substitute image” of “Select image” is sent to the other party.

You cannot answer calls by opening the FOMA phone in Horizontal Open Style even when “Answer” is set.

+m-1-8

Setting when Folded

Setting Response for when Closing FOMA Phone during a Call

Set Response for when Closing FOMA Phone during a Voice Call/Videophone Call

Set Response for when Closing FOMA Phone during PushTalk

m

SettingsTalkVolumeUseBo or

to adjust the earpiece volume.

Adjust the earpiece volume to Level 1 (minimum) through Level 6 (maximum).

During a call, PushTalk call, or calling, you can press

or </> to adjust the volume, and while entering

phone number, you can press and hold

(for at least

one second) to adjust it. Press

or </> within two

seconds to adjust it.

Information

This function is disabled when the Flat-plug Earphone/ Microphone with Switch (option) is connected. The communication state does not change even if you close the FOMA phone during a voice call or PushTalk communication. If you close the FOMA phone during a videophone call, the substitute image is sent to the other party with the line connected.

If you close the FOMA phone during a videophone call with “No tone” activated, a substitute image is sent to the other party. When “Tone on” is set, the still image set for “Holding” of “Select image” is sent.

If you set to “No tone” or “Tone on”, “Holding” is displayed on the Private window when the FOMA phone is closed.

Even when “End the call” has been set, the call does not end if you close your FOMA phone from Horizontal Open Style. “No tone” works for a voice call/videophone call, and “Speaker call” works for a PushTalk call.

Volume

Adjusting Earpiece Volume

Information

The earpiece volume adjusted during a call is retained even after the call ends.

When you adjust the earpiece volume, the sound volume during a Hands-free call or speaker call for PushTalk is also adjusted.

Voice/Videophone Calls

You can adjust the ring volume for incoming calls and mail.

m

SettingsSoundRing volume



Select an incoming type



Use

to adjust the volume.

Following icons are displayed on the Stand-by display while the ring volume is set to “Silent”:

: The ring volume for voice calls, PushTalk calls or

videophone calls is “Silent”.

: The ring volume for mail, chat mail or Messages

R/F is “Silent”.

: The ring volume for voice calls, PushTalk calls, or

videophone calls is “Silent” and the ring volume for mail, chat mail, or Messages R/F is “Silent”.

If you have set “Step”, the ring tone is silent for about three seconds, and then the volume steps up every three seconds, from Level 1 through Level 6.

During ringing of a voice call or videophone call, you can adjust the ring volume also by pressing

or by

pressing and holding

</>

for at least one second. However, you cannot adjust the ring volume in the following cases:

・

Ring Volume is set to “Step”.

・

“Answer setting” is set to “Quick silent” and you stop the ring tone or voice guidance.

・

During Manner Mode

・

Incoming calls within the ring start time specified by “Ring time”

During ringing

h

The FOMA phone makes three rapid beeps for confirmation and the call is put on answer-hold (On Hold).

The confirmation tone does not sound while Manner Mode is activated or when “Phone” of “Ring volume” is “Silent”.

The other party hears the hold tone set for “On hold tone” of “Set hold tone”. For videophone calls, the still image set for “On hold” of “Select image” is displayed.

PressOo() or

to release hold

and answer the call.

If “Answer setting” is set to “Any key answer”, you can release hold of voice calls by pressing any key of

through

9,a,s,r,m,c,Mo

<,>,l

, or i.

If a videophone call is on hold, the image through your

camera is sent to the other party by pressing

() or

to release hold. If you press

( ) to release hold, the substitute image is sent.

+m-5-0

Ring Volume

Adjusting Ring Volume

On Hold

Putting an Incoming Call on Hold when You cannot Answer at Once

During a call

Oo

()

The other party hears the hold tone set for “Holding tone” of “Set hold tone”. For videophone calls, the still image set for “Holding” of “Select image” is displayed.

You can put the call on hold by closing the FOMA phone during the call if you have set “Setting when folded” to “Tone on”.

Press Oo() or

to release hold

and answer the call.

If a videophone call is on hold, the image through your

camera is sent to the other party by pressing

()

to release hold. If you press

( ) to release hold, the substitute image is

sent.

If you have set “Setting when folded” to “Tone on” and put the call on hold by closing the FOMA phone, open the FOMA phone or connect the Flat-plug Earphone/ Microphone with Switch (option) to answer the call. If you connect the Flat-plug Earphone/Microphone with Switch to answer the videophone call, the substitute image is sent to the other party.

Information

The caller is charged for the call even during answer-hold (On Hold).

If you press

-h

during answer-hold (On Hold), the call

will be disconnected.

Holding

Putting a Call on Hold during a Call

Information

The caller is charged for the call even while the call is on hold.

If a new call comes in while the current call is put on hold, the hold (Holding) is released.

Voice/Videophone Calls

You can set the guidance the other party hears during on hold.

m

SettingsTalkSet hold tone



On hold tone or Holding tone



Select a hold tone.

Tone 1/2

. . . The caller hears the pre-installed guidance in

Japanese.

JESU JOY OF MAN’S

. . . The caller hears the melody. You can set this for

“Holding tone” only.

Voice announce

. . . The caller hears the sound recorded by “Voice

announce”. If it has not been recorded, this is not displayed.

Pressl( ) to play back a hold tone. Press

to end the demo playback.

Public Mode is an auto-answer service that puts importance on manners in public spaces. Once you activate Public Mode, the guidance is played back telling that you cannot answer the call as you are currently driving or in a place (a train, bus, movie theater, etc.) where you should refrain from answering the call. Then the call is disconnected.

Press and hold

for at least one second.

Public Mode is activated and “ ” is displayed. When a call comes in, the guidance “The person you are calling is currently driving or in an area where cell phone should not be used. Please try again later.” is played back for incoming calls.

To deactivate Public Mode, perform the same operation. Then, Public Mode is deactivated and “ ” disappears.

Set Hold Tone

Setting Hold Tone

Public Mode (Drive Mode)

Using Public Mode (Drive Mode)

Information

You can activate/deactivate Public Mode only from the Stand-by display. You can activate/deactivate Public Mode even when “ ” is displayed.

You can make calls as usual even during Public Mode.

If you make an emergency call at 110/119/118, Public Mode is released.

When Public Mode and Manner Mode are activated simultaneously, Public Mode has priority.

If a “User unset” call comes in while “Caller ID request” is set to “Activate”, the Caller ID Request guidance is played back. (The Public Mode guidance is not played back.)

You cannot use this function during data communication.

■

Relations between incoming calls during Public Mode (Drive Mode) and respective services

■

When Public Mode (Drive Mode) is activated

・

Even when a call comes in, the ring tone does not sound. The “Missed call” icon appears on the display and the call is stored in “Received calls”. The guidance is played back to the caller to the effect that you are currently driving or in an area where mobile phones should not be used. Then the call is disconnected. When a PushTalk call comes in, no answer is made and the message “Connection failed” appears on the caller’s display. For the talk among three or more members, the message to the effect that you are driving is conveyed to them. However, when the power is off or “ ” is displayed, the caller hears the out-of-service area guidance instead of the Public Mode guidance.

・

The ring tone does not sound and the Call/Charging indicator does not flicker even when mail or a message comes in. In addition, the set vibrator does not work.

・

The ring tone for 64K data communication, alarm tone, and charging confirmation tone do not sound, and a melody while i-

ppli is running is not played back.

・

The tickers of i-Channel are not displayed.

・

The Call/Charging indicator does not light for “Illum. when folded”.

Service

Responses to

Incoming Voice Calls

Responses to Incoming

Videophone Calls

Voice Mail

Service

※

Plays back the Public Mode guidance, and then the call is connected to the Voice Mail Service Center.

Does not play back the video guidance for Public Mode, and the call is connected to the Voice Mail Service

Center. Call Forwarding

Service

※

Plays back the Public Mode guidance, and then the call is forwarded to the forwarding destination. Whether the guidance is played back or not depends on the guidance setting of Call Forwarding Service. If “Plays guidance” is set, plays back the Public Mode guidance. If “Does not play guidance” is set, does not play back the guidance.

Does not play back the

video guidance for

Public Mode, and the

call is forwarded to the

forwarding destination.

If the destination does

not support videophone

calls, the call is

disconnected.

Call Waiting Service

Plays back the Public Mode guidance, and then the call is disconnected.

Plays back the video

guidance for Public

Mode, and then the call

is disconnected.

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Voice/Videophone Calls

※

When the ring time is set to 0 seconds, the FOMA phone is out of the service area, or the power is off, the Public Mode guidance is not played back, but Voice Mail Service or Call Forwarding Service works. Note that in this case the call is not notified by the “Missed call” icon and not stored in “Received calls”.

Public Mode (Power Off) is an auto-answer service that puts importance on manners in public spaces. Once you activate Public Mode (Power Off), the guidance is played back telling that you cannot answer the call as you are currently in a place (hospital, airplane, around priority seat in a train, etc.) where use is prohibited. Then the call is disconnected.

Enter “:25251”

d

Public Mode (Power Off) is set. (Nothing is changed on the Stand-by display.) After setting Public Mode (Power Off) and turning off the power, the guidance “The person you are calling is currently in an area where use is prohibited. Please try again later.” is played back for incoming calls.

To release Public Mode (Power Off), dial “:25250”.

To check the setting for Public Mode (Power Off), dial “

25259”.

Nuisance Call Blocking Service

For the call from the phone number registered to be rejected, plays back the Call Rejection guidance, and then the call is disconnected.

For the call from the phone number registered to be rejected, plays back the video guidance for Call Rejection, and then the

call is disconnected. Caller ID Display Request Service

For the caller without a caller ID, plays back the Caller ID Request guidance, and then the call is disconnected. For the caller with a caller ID, plays back the Public Mode guidance, and then the call is disconnected.

For the caller without a

caller ID, plays back

the video guidance for

Caller ID Request, and

then the call is

disconnected.

For the caller with a

caller ID, plays back

the video guidance for

Public Mode, and then

the call is

disconnected.

Public Mode (Power Off)

Using Public Mode (Power Off)

Service

Responses to

Incoming Voice Calls

Responses to Incoming

Videophone Calls

■

Relations between incoming calls during Public Mode (Power Off) and respective services

■

When Public Mode (Power Off) is activated

The setting stays activated until you dial “:25250” to deactivate Public Mode (Power Off). You cannot deactivate the setting just by turning on the power. The guidance is played back to the caller telling that you are currently in a place where you should turn off the power. Then the call is disconnected. When a PushTalk call comes in, no answer is made and the message “Connection failed” appears on the caller’s display. For the talk among three or more members, the message to the effect that you do not participate is conveyed to them. The Public Mode (Power Off) guidance is played back even when you are out of the service area or out of reach of radio waves.

Service

Responses to

Incoming Voice Calls

Responses to Incoming

Videophone Calls

Voice Mail Service

Plays back the Public Mode (Power Off) guidance, and then the call is connected to the Voice Mail Service

Center.

※

Does not play back the video guidance for Public Mode (Power Off), and the call is connected to the Voice

Mail Service Center. Call Forwarding Service

Plays back the Public Mode (Power Off) guidance, and then the call is forwarded to the

forwarding destination.

※

Whether the guidance is played back or not depends on the guidance setting of Call Forwarding Service. If “Plays guidance” is set, plays back the Public Mode (Power Off) guidance. If “Does not play guidance” is set, does not play back the guidance.

Does not play back the

video guidance for

Public Mode (Power

Off), and the call is

forwarded to the

forwarding destination.

If the destination does

not support videophone

calls, the call is

disconnected.

Nuisance Call Blocking Service

For the call from the phone number registered to be rejected, plays back the Call Rejection guidance, and then the call is disconnected.

For the call from the

phone number

registered to be

rejected, plays back the

video guidance for Call

Rejection, and then the

call is disconnected.

Voice/Videophone Calls

※

When the ring time is set to 0 seconds, the Public Mode (Power Off) guidance is not played back, but Voice Mail Service or Call Forwarding Service works.

When you could not answer calls (Missed calls), the “Notification icon” appears on the Stand-by display. You can check Received Calls by selecting the icon.

OoOo

()

Press

to return to the former display.

When multiple icons are found, use Mo to highlight an icon and press

().

See page 30 for when the FOMA phone is closed.

By activating Record Message, you can play back an answer message to incoming calls and record callers’ voice/video messages when you cannot answer them even if you have not signed up for Voice Mail Service. You can record up to five messages for voice calls and up to two messages for videophone calls. Each message can be recorded for up to 20 seconds.

Caller ID Display Request Service

For the caller without a caller ID, plays back the Caller ID Request guidance, and then the call is disconnected. For the caller with a caller ID, plays back the Public Mode (Power Off) guidance, and then the call is disconnected.

For the caller without a caller ID, plays back the video guidance for Caller ID Request, and then the call is disconnected. For the caller with a caller ID, plays back the video guidance for Public Mode (Power Off), and then the call is disconnected.

Missed Call

If You could not Answer an Incoming Call

Service

Responses to

Incoming Voice Calls

Responses to Incoming

Videophone Calls

Notification icon

+m-5-5

Record Message Setting

Recording Voice/Video Messages when You cannot Answer the Call

m

LifeKitRec. msg/voice memo



Record message settingON or OFF



Select an answer message.

Press l( ) to play back the answer message. Press

to end the demo playback.

When “Japanese 1”, “Japanese 2”, or “English” is set, a beep sounds after playing back the answer message to the other party. If “Voice announce” is set, the beep does not sound.

Enter a ring time (seconds).

Enter from “000” through “120” in three digits.

You cannot set the same ring time for Remote Monitoring, Auto Answer Setting and Record Message Setting. Set a different time for each.

While Record Message is activated, “ ”〜“” (the number of recorded messages for voice calls) and “ ”

〜

“ ” (the number of recorded messages for

videophone calls) are displayed.

Activate Record Message

■

Incoming calls when Record Message Setting is set to “ON”

For videophone calls, the still image set for “Preparing” of “Select image” is displayed on the other party’s display while playing back the answer message, and the still image set for “Record message” of “Select image” is displayed while recording.

To answer a call while the answer message is played back or a voice/video message is recorded, press

() or

For videophone calls, press

() or

to send

the image through your camera, or press

() to send a substitute image. You can answer a call also by pressing the switch on the Flat-plug Earphone/Microphone with Switch (option). For videophone calls, the image through your camera is sent to the other party.

Incoming Call Playing back the

answer message

Recording a voice/

video message

Displaying an icon on the

desktop (See page 112)

The ring

time

elapses

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Voice/Videophone Calls

Even if a call comes in while Record Message is not activated, you can record the caller’s voice/video message just for that incoming call.

During ringing

l

() or

Manner Mode is also activated. The caller will hear the answer message and then can leave you a voice/video message.

Record Message does not work when five messages for voice calls and two messages for videophone calls have already been recorded or when a PushTalk call comes in. Only Manner Mode is set when you operate by pressing

When “Side keys guard” is set to “ON”, you cannot activate Record Message by pressing

with the

FOMA phone closed.

Information

Record Message does not work when “ ” is displayed.

When Public Mode (Drive Mode) and Record Message are simultaneously activated, the former has priority and the latter does not work.

The priority order of answer messages is as follows: “Setting for Phonebook entry”

→

“Group setting” → “Record

message setting”.

If “Voice announce” selected as an answer message is deleted, the answer message will be set to “Japanese 1”.

When Voice Mail Service or Call Forwarding Service is set at the same time as Record Message, the priority depends on the ring time set for Voice Mail Service or Call Forwarding Service. To give Record Message priority, set the ring time for Record Message Setting shorter than that for Voice Mail Service or Call Forwarding Service. Even when you do this, Voice Mail Service or Call Forwarding Service will work if there are already five record messages for voice calls and two record messages for videophone calls.

You cannot receive a call from a third party while a voice/ video message is being recorded. The third party will hear the busy tone.

Quick Record Message

Recording Voice/Video Messages when You cannot Answer the Call during Ringing

m

LifeKitRec. msg/voice memo



Play/Erase msg.



Select a record message or voice memo.

A beep sounds and playback starts.

On the Record Message List, recorded items are indicated by “

★

”.

It is played back at the volume set for “Volume” (earpiece volume).

When playback ends, a double-beep sounds and the message “Playing” is cleared from the display.

The date and time the message/memo was recorded are displayed during playback. When a caller’s phone number is provided, it is displayed. If the caller is stored in the Phonebook, his/her name is also displayed. However, the name is not displayed and the phone number only is displayed in the following cases:

・

When you play back a record message from the caller stored as secret data in Normal Mode

・

When you play back a record message for Number A in B Mode (or vice versa) while using 2in1

If the caller’s phone number is displayed during playback, you can make a voice call to that phone number by pressing

. Press l() to make

a videophone call and press

to make a PushTalk

call.

+m-5-5

Play/Erase Messages Play/Erase Videophone Messages

Playing Back/Erasing Record Messages/a Voice Memo/Videophone Record Messages/Movie Memos

Play Back/Erase Record Messages/ a Voice Memo

<> <>

Record Message List

■

To play back using

From the Stand-by display, press > to play back the latest record message. When record messages are not recorded, a voice memo is played back.

■

To skip to next message

Each time you press > during playback, messages are played back in the following order: the next new record

message

→

the oldest record message → a voice memo.

■

To cancel playback midway

PressOo() or

Voice/Videophone Calls

m

LifeKitRec. msg/voice memo



Play/Erase VP msg.Select a videophone

record message or movie memo.

On the Videophone Record Message List, recorded items

are indicated by “

★

”.

It is played back at the same volume of the playback sound of i-motion movies.

The date and time the message/ memo was recorded are displayed during playback.

Play Back/Erase Videophone Record Messages/Movie Memos

Videophone Record

Message List

■

To play back using

From the Stand-by display, press and hold > for at least one second to play back the latest videophone record message. When videophone record messages are not recorded, the latest movie memo is played back.

■

To cancel playback midway

PressOo() or

Function Menu of the Record Message List/ Videophone Record Message List

Function menu

Operation/Explanation

Play

You can play back a message.

Erase this



YES

You can erase a message/memo also by pressing

( ) during playback.

Erase rec. msg.

You can erase all record messages from the Record Message List, and can erase all videophone record messages from the Videophone Record Message List.



YES

Erase movie memo

[Videophone Record Message List only]

You can erase all movie memos.



YES

Erase all

You can erase all record messages and a voice memo from the Record Message List, and can erase all videophone record messages and movie memos from the Videophone Record Message List.



YES

You can send a Chara-den image instead of the image through your camera.

See page 288 for Chara-den images.

You can set a Chara-den image to be sent to the other party for making a videophone call.

Chara-den display/Chara-den List

l

()

Enter the destination phone number and press

( ) to make a videophone call.

When the other party’s phone number is stored in the Phonebook, you can retrieve it selecting from the Search Phonebook display by pressing

You can search for the phone number also from Received Calls by pressing

or from Redial by

pressing

You can set a Chara-den image for “Substitute image” of “Select image”.

Chara-den display/Chara-den List/Chara-den Recording display

i

()



Substitute image

From the Chara-den List, you can set it also by pressing

().

You can perform settings for a Chara-den call. These settings are effective only for during a videophone call.

During a Chara-den call

i

()



Chara-den setup



Do the following operations.

Using Chara-den

Set by Call

Information

The priority order of substitute images to be sent to the

other party is as follows: “Setting by call”

→

“Setting for

Phonebook entry”

→

“Group setting” → “Select image”.

Substitute Image

Chara-den Setup

Item Operation/Explanation

Switch Chara-den



Select a Chara-den image.

If you switch Chara-den images, the action mode switches to Whole Action Mode.

Action list

You can display the list for actions that you can operate.

Highlight an action and press Oo()

to execute the action. Press

() to

check the details of the action.

You can display the Action List also by pressing

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Voice/Videophone Calls

You can switch images to be sent to the other party from through the inside camera to through the outside camera.

During a videophone call



()

Press l( ) again to switch to the image through your inside camera.

The setting here is effective only for the current videophone call.

You can switch images to be sent to the other party from the image through your camera to the still image or Chara-den image set as the substitute image. See page 288 for Chara-den.

During a videophone call



()

The substitute image is sent to the other party. “ ” is displayed while the still substitute image is being sent, and “ ” is displayed if you have set a Chara-den image as a substitute image (during a Chara-den call).

Pressm( ) again to switch from the substitute image to the image through your camera.

Change action

You can switch the action mode between Whole Action Mode ( ) and Parts Action Mode ( ).

You can switch modes also by pressing

SW substitute img.

You can switch a substitute image to be sent to the other party to the still image set for “Pre-installed” of “Select image”.

SW org. subst. img.

You can switch a substitute image to be sent to the other party to the still image set for “Original” of “Select image”.

Useful Functions for Videophone Calls

Switching Cameras

At videophone start-up Inside camera

Item Operation/Explanation

At videophone

start-up

Whole Action

Mode

Send Substitute Images

Information

The priority order of substitute images to be sent to the other party is as follows: “Setting by call”

→

“Setting for

Phonebook entry”

→

“Group setting” → “Select image”. Note that “Setting for Phonebook entry” and “Group setting” are disabled when a videophone call comes in without notifying the caller ID.

Even when you make a videophone call sending a substitute image, you are charged for the digital communication.

You can switch the display locations of the receiving image and the sending image.

During a videophone call, press



().

Each time you press c( ), the displays switch.

You can adjust the magnification for the camera image to be sent to the other party. During a videophone call, the maximum magnification is about 3.3 times for the inside camera and about 5.5 times for the outside camera.

During a videophone callUse

adjust the magnification.

The former zoom setting returns when the videophone call ends.

Switch Image Display Positions

+cc

Zoom

At videophone start-up Wide

Function Menu during Videophone Call

Function menu

Operation/Explanation

CHG to voice call

See page 52.

Photo light

You can turn on the photo light when sending the image through the outside camera to the other party.



ON or OFF

Talk on BT/ Phone

You can set whether to communicate through the FOMA phone or a Bluetooth device. (See page 352)

At videophone

start-up

OFF

Voice/Videophone Calls

Send DTMF tone/ DTMF tone OFF

During a Chara-den call, you can switch to the DTMF Transmission Mode that enables you to enter the data from the numeric keys and to send DTMF (touch-tone signals). You can operate it only during a Chara-den call.

“Send DTMF tone” is displayed when the mode is not DTMF Transmission Mode and “DTMF tone OFF” is displayed in DTMF Transmission Mode.

In DTMF Transmission Mode, you cannot operate the action of Chara-den images.

The DTMF tone may not be received depending on the device of a receiving end.

V.phone settings (Visual preference)

See page 71.

V.phone settings (Brightness)

You can adjust the brightness of the camera image to be sent to other party to -3 (dark) through +3 (bright).



BrightnessSelect a brightness level.

V.phone settings (White balance)

You can adjust the colors of the camera image to be sent to the other party, to make the colors look more natural.



White balanceSelect an item.

Fine weather

. . . . . . For talking outdoors in

fine weather

Cloudy weather

. . . For talking in cloudy

weather or in the shade

Automatic

. . . . . . . . For adjusting white

balance automatically

Light bulb

. . . . . . . . For talking under

incandescent light

V.phone settings (Color mode set)

You can switch the color tone of the camera image to be sent to the other party.



Color mode setSelect a color tone.

V.phone settings (Night mode)

You can lengthen the camera’s exposure time to make the camera image to be sent clear in a dark place.



Night modeON or OFF

V.phone settings (Focus)

You can set the focus for the outside camera during a videophone call.



FocusClose-up or Landscape

The focus for the inside camera is fixed to “Portrait” (suitable mode to shoot portraits), so you cannot change the setting.

Chara-den setup

See page 69.

Backlight

You can select whether to light the display constantly or light for about 15 seconds after an operation.



Constant light or 15 seconds light

LCD AI

See page 107.

Own number

You can display your phone number.

Key guide

You can display the guide of key operation during a videophone call.

Function menu

Operation/Explanation

At videophone

start-up

At videophone

start-up

Automatic

At videophone

start-up

Normal

At videophone

start-up

OFF

At videophone

start-up

Landscape

You can set whether to switch to Hands-free automatically for when a videophone call starts.

m

SettingsVideophone



Hands-free w/ V. phoneON or OFF

See page 60 for the operation while Hands-free is activated and how to switch to Hands-free.

You can set the quality of both the receiving image and sending image on the display.

m

SettingsVideophone



Visual preferenceSelect an image quality.

“Prefer motion spd” is effective for moving images. When there is little motion, the quality becomes better if you set to “Prefer img qual”.

If you operate from the Function menu during a videophone call, the setting is effective only for the current videophone call.

You can set an image to be sent to the other party instead of the camera image.

m

SettingsVideophoneSelect image



Select an item.

On hold

. . . . Sets an image for during answer-hold

(On hold).

Holding

. . . . Sets an image for while a call is on hold

(Holding).

Substitute image

. . . . . . . . . . . Sets a substitute image (still image or

Chara-den) for when a camera is off.

Record message

. . . . . . . . . . . Sets an image while recording a record

message.

Preparing

. . . Sets an image for while playing back an

answer message.

Movie memo

. . . . . . . . . . . Sets an image for while recording a movie

memo.

Hands-free with Videophone

Setting Videophone Hands-free

Visual Preference

Setting Image Quality for Videophone Calls

Information

If the radio wave conditions weaken during a videophone call, the image may appear like a mosaic.

Select Image

Changing Image Displays for Videophone Calls

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Voice/Videophone Calls

Select an image.

Pre-installed

. . .For sending a pre-installed still image to

the other party.

Original

. . . . . .For sending an appropriate message

with a still image stored using “Set display”.

Chara-den

. . . .For sending a Chara-den image selected

by “Substitute image”. (See page 69) (Displayed only when “Substitute image” has been selected in step 1.)

Pressl( ) to play back a demo to check the still image or Chara-den image.

To change the setting of “Original” or “Chara-den”, press

( ), select “Change setting”, then select a still image or Chara-den image. If you have selected “Original”, select a still image after selecting a folder. See “Set display” for settable still images.

You can set an image to be sent to the other party for making a videophone call.

Enter a phone number

bring up the detailed display of a Phonebook entry, redial item, dialed call record, or received call record.

()



Select image



Me or Chara-den

The setting is completed when you select “Me”.

To cancel the setting by call, select “Release”. The setting is completed.

Select a Chara-den image.

If a videophone call cannot be connected, it will be automatically redialed as a voice call.

m

SettingsVideophone



Voice call auto redialON or OFF

Information

Even if you delete the still image selected from “Original”, that still image is displayed to the other party. To change, set by “Change setting” or “Set display”.

Set by Call

Voice Call Auto Redial

Redialing as a Voice Call when a Videophone Call cannot be Connected

Information

The charges for calls once switched to voice calls are billed at the rates for the voice calls.

You can let the other party know that your FOMA phone can switch between a voice call and videophone call. This function is set to “Indication ON” at the time of contract. When “Notify switchable mode” is set to “Indication ON”, the caller can switch between the videophone call and voice call.

You cannot operate “Notify switchable mode” when you are out of the service area or radio waves do not reach, or during a call.

m

SettingsVideophone



Notify switchable mode



Do the following operations.

m

SettingsIncoming call



V-phone while packetSelect an item.

V-phone priority

. . .Shows the Videophone Call Receiving display. When

you answer the videophone call, packet communication is disconnected.

Packet downld priority

. . .Rejects the videophone call and continues the

communication.

V-phone answerphone

. . .Connects the incoming videophone call to the Voice

Mail Service Center.

Call forwarding

. . .Forwards the incoming videophone call to the

forwarding destination.

Voice Call Auto Redial does not work when a videophone call cannot be connected such as when the line is busy or the other party’s phone is in Public Mode (Drive Mode). However, Voice Call Auto Redial works when you make a videophone call to a phone that does not support the videophone function.

Notify Switchable Mode

Setting for Switching between a Voice Call and a Videophone Call

Information

Item Operation/Explanation

Indication ONYESOK

Indication OFF



YESOK

Check indication

You can check the setting of the function.

Videophone while Packet

Selecting Response to Incoming Videophone Calls during i-mode

Voice/Videophone Calls

You can operate your FOMA phone from an external device such as your personal computer for making or receiving videophone calls by connecting them using the FOMA USB Cable with Charge Function 01 (option). To use this function, you need to install a videophone application program on a dedicated external device or personal computer, and further, you need to prepare equipment (commercial item) such as an earphone/ microphone or USB compatible web camera.

For operating environments for a videophone application program and how to set or operate it, refer to the instruction manual or other literature for an external device.

You can use “

ドコモテレビ電話ソフト

(DoCoMo

Videophone Software)” for the application program that supports this function. Download it from the DoCoMo Videophone Software web site. (For details such as operating environment for the personal computers, refer to the support web page.)

http://videophonesoft.nttdocomo.co.jp/

(Japanese only)

※

You cannot make a videophone call at 32 kbps communication speed.

Information

If you have not signed up for Voice Mail Service or Call Forwarding Service, “Packet downld priority” works even if you set to “V-phone answerphone” or “Call forwarding”.

Connecting FOMA Phone to External Devices to Use Videophone Function

Information

You cannot make a videophone call from the external device during a voice call.

When you have signed up for Call Waiting Service, an incoming videophone call from an external device during a voice call is recorded as a missed call in Received Calls. The same applies for an incoming voice call, videophone call, and 64 data communication during a videophone call from an external device.

Base station

FOMA videophone communication speed 64K or 32K

※

FOMA

network

You can use the inside camera of the FOMA phone as a monitoring camera to observe the remote location from a phone that has the videophone function based on 3G-324M. While “Remote monitoring” is set to “ON”, the FOMA phone automatically starts Remote Monitoring when it receives a videophone call from a phone number stored as “Other ID” of “Remote monitoring”. (The FOMA phone needs to be set to Normal Style.)

m

SettingsVideophone



Remote monitoring



Enter your Terminal Security Code.

To release Remote Monitoring, select “Set”, then select “OFF”.

Other ID<Not recorded>



Enter a phone number.

To change, select the stored phone number.

You can store up to five phone numbers that can enter up to 26 digits by using numerals, #,

, or +.

To return to the setting display for Remote Monitoring, press

from the Other ID List after storing phone number.

Ring timeEnter a ring time (seconds).

You can enter the time from “003” through “120” in three digits until Remote Monitoring starts after receiving a videophone call.

You cannot set the same ring time for Remote Monitoring, Auto Answer Setting and Record Message Setting. Set a different time for each.

SetON

When receiving videophone calls from the phone numbers stored as “Other ID”, the FOMA phone automatically answers to start Remote Monitoring after the ring time elapses.

“ ” is displayed while this function is set to “ON”.

You cannot set to “ON” in Manner Mode.

Remote Monitoring

Checking inside the Room when You are Out

Other ID List

Function Menu of the Other ID List

Function menu

Operation/Explanation

Look-up address

You can call up a phone number in the Phonebook, Dialed Calls, or Received Calls to enter it.



Select an item.

Phonebook

. . . . . . Call up a Phonebook

entry and select a phone number.

Dialed calls

. . . . . . Highlight a phone number

and press

().

Received calls

. . . Highlight a phone number

and press

().

Delete this



YES

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Voice/Videophone Calls

Make a videophone call from a stored phone number.

After the ring time set for “Remote monitoring” elapses, Remote Monitoring automatically starts.

The image through the receiving end’s camera appears on the display and the sound comes out of the speaker.

You cannot set Voice-only Remote Monitoring.

Make a videophone call notifying your caller ID. If the caller ID is not notified, Remote Monitoring will not start and the call will be handled as an ordinary incoming videophone call.

Remote Monitoring ends when the calling end or receiving end presses

Delete all



YES

Information

If you delete all phone numbers stored as “Other ID”, “Remote monitoring” is set to “OFF”.

Perform Remote Monitoring

Function menu

Operation/Explanation

■

For answering a videophone call without starting Remote Monitoring at the receiving end

PressOo() or

before the FOMA phone

answers a videophone call automatically. If you press

( ), the videophone call starts sending the

substitute image to the other party.

When a remote monitoring call comes in, “Setting when opened” is disabled.

If you press

when a remote monitoring call comes in,

the call will be cut and Remote Monitoring will not start.

Information

When your FOMA phone is used for the receiving end, an image through the caller’s camera appears, and sound comes out. (You cannot switch to a substitute image.)

Remote Monitoring does not start during Manner Mode and Public Mode (Drive Mode). However, it starts even during Lock All.

When Remote Monitoring is set to “ON” and a videophone call comes in from the phone number set as “Other ID”, Remote Monitoring starts after the set ring time, even when “Ring time”, “Auto answer setting”, or “Record message setting” is set and regardless of their ring times.

When Remote Monitoring is not performed, it is recorded in Received Calls as a missed videophone call.

If the Flat-plug Earphone/Microphone with Switch (option) is connected when a remote monitoring call comes in, the ring tone will sound from both the earphone and the speaker, even when “Headset usage setting” is set to “Headset only”.

You may be imposed punishment according to the law and rule (such as the nuisance prevention ordinance) if you use the FOMA phone to give a remarkable nuisance and misdeed to the public.

The ring tone for Remote Monitoring sounds. (You cannot change the ring tone for Remote Monitoring.) The ring tone sounds at the volume set for “Videophone” of “Ring volume”, but at “Level 2” if you have set “Step”, “Level 1” or below. The flickering color is “Gradation”, and its flickering pattern is “Standard”, regardless of the Illumination setting.

You cannot put incoming remote monitoring calls on answer-hold (On Hold).

If you set both Call Forwarding Service and Remote Monitoring, and give priority to Remote Monitoring, set its ring time shorter than that for Call Forwarding Service.

To use Call Forwarding Service for Remote Monitoring, store the phone number of dialing side as “Other ID” and set a 3G-324M videophone as the forwarding destination.

Please be considerate of the privacy of individuals around you when shooting and sending photos using camera-equipped mobile phones.

Information

PushTalk

What is PushTalk? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Making a PushTalk Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Adding a Member during PushTalk Communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Receiving a PushTalk Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Storing in PushTalk Phonebook . . . . . . . . . . . . . . . . . . . . . . . ‹Store in PushTalk Phonebook› 79

Making a PushTalk Call Using PushTalk Phonebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Deleting PushTalk Phonebook Entries . . . . . . . . . . . . . . .‹Delete from PushTalk Phonebook› 80

Making Full Use of PushTalk Phonebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Setting PushTalk Calling/Receiving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

PushTalk

You can communicate with multiple persons (up to five persons including yourself); press the PushTalk key to access the PushTalk Phonebook, select the persons you want to talk with, and press the PushTalk key. You are charged a PushTalk communication fee each time you press (talk) the PushTalk key.

For details on PushTalk or compatible models, refer to DoCoMo web page or “Mobile Phone User’s Guide [Network Services]”.

■

PushTalkPlus

※

This service enables you to have a PushTalk call with up to 20 persons including you. You can use the shared Phonebook on the network, and can check the members for their status, thus PushTalk becomes more useful.

※

You need to subscribe separately.

For details such as how to operate, refer to the booklet which is supplied at subscription.

Enter the other party’s phone number

p

When you are dialing, a confirmation tone for starting a PushTalk call sounds for a few seconds, and then the same ring tone as the voice (videophone) call sounds.

You can make a group call to multiple persons using the PushTalk Phonebook. (See page 79 and page 80)

When the other party answers, talk while pressing

When the other party answers, a confirmation tone for starting communication sounds.

“ ” blinks during dialing and lights during communication.

When you get the talker’s right, the talker’s right obtained tone sounds. The other party hears your voice only while you are pressing

and having the

talker’s right. When you release

, the talker’s right is released, and a confirmation

tone sounds.

You cannot get the talker’s right and an error tone sounds even if you press

when another member has

it.

Pressl( ) or press i( ) and select “Add member” to add a member. Go to step 1 on page 77.

What is PushTalk?

Making a PushTalk Call

Press

to end the communication after

talking.

A tone to notify the disconnection of communication sounds at the other end.

When the call you made is a group call, the PushTalk communication itself continues even if you press

, and the icon indicating that you are not participating appears on each member’s display and a confirmation tone sounds. However, when all the members exit, the PushTalk communication itself ends.

Information

The talker is charged a communication fee from when he/ she presses

and the talker’s right obtained tone sounds.

You cannot make emergency calls at 110/119/118 from PushTalk.

The duration you can talk per talker’s right is limited. The talker’s right release notice tone sounds before the limited time arrives, and the talker’s right is released. In addition, the PushTalk communication itself ends when no one gets the talker’s right in a certain period of time.

Just after purchase, Hands-free is automatically activated by “Hands-free w/ PushTalk” (See page 81). However, Hands-free is deactivated during Manner Mode regardless of “Hands-free w/ PushTalk”.

The FOMA phone works according to “Setting when folded” if you close it during communication. You can set also by pressing

( ) and selecting “Set. when folded”.

(See page 63)

Whether to notify others of your phone number when you make PushTalk calls follows the setting for “Activate” of “Caller ID notification” (see page 47). However, when you set “Notify caller ID” from the Function menu for dialing, or when “Notify”/“Not notify” is displayed in the detailed Redial/Dialed Call/Received Call display, each of those settings will work.

When you make a PushTalk call with your phone number notified, your phone number as well as all members’ phone numbers are notified to all members including added members. When you make the PushTalk call without notifying your phone number, “User unset” appears in the caller’s and member’s fields on the displays of all the members including added members. Your phone number is very important information, so take the utmost care to notify it to others.

If you make a PushTalk call during i-mode communication, the i-mode communication is disconnected.

You cannot use PushTalk by Number B of 2in1.

■

Making/Receiving a PushTalk group call

You can use the PushTalk Phonebook or Redial/Dialed Calls/ Received Calls to communicate with multiple members. While making or receiving a PushTalk group call, the group name and the members in the group are displayed. Press

to confirm other members. When a call is received with the other party’s phone number not provided, “User unset” is displayed.

PushTalk

■

Display while dialing/communicating



The phone number of the member who has the talker’s right is displayed, and the state of the talker’s right is displayed in color of the round icon at the upper left. When the name of that member, phone number, and image are stored in the Phonebook, his/her name and image are displayed. However, when you cannot receive a member’s information correctly, “?” is displayed. When the FOMA phone is closed, the phone number (name) of the member who has the talker’s right is displayed on the Private window.



The state of members is shown by icons during dialing or communicating. (Characters other than shown below might appear.)

※

Displayed only for the PushTalk communication among three or more members.



The number of times you have got the talker’s right is the total of the number of and the number shown in . When 999 times are exceeded, the counting is reset to 0.

■

Re-participating or participating midway in PushTalk communication

Use Redial/Dialed Calls/Received Calls to make a PushTalk call so long as the PushTalk communication continues among other members.

If the PushTalk communication has already been finished, your call is dialed as a new PushTalk call.

Color of the round icon at the upper left

State of the talker’s rights

Blue Calling

Green You can get the talker’s right.

Blinking in green

You have the talker’s right.

Blinking in yellow

Another member has the talker’s right.

Blinking in

green and red

The talker’s right will be released automatically in a few seconds because it has long been retained (A release notice tone sounds).

Icon State of members

※

Calling

Has participated in the PushTalk call.

※

Does not answer, has ended the PushTalk call, out of the service area, or the power is off.

※

Has activated Public Mode (Drive Mode).







During group

communication

You can make a PushTalk call to another member during PushTalk communication and add that member to the communication. You can add a person to the members by accessing the PushTalk Phonebook, Phonebook, or Dialed Calls/ Received Calls, or by directly entering a phone number. You can add up to five members (including yourself), and can repeat adding up to that number.

Members can be added from the calling end only.

You can add even the members who use the PushTalk compatible models which do not have this function.

If you have already made a call to four members, you cannot add a new member though you can call up a member who has exited the call again.

The added members are not stored in Redial/Dialed Calls.

During PushTalk communication

l

()



Do the following operations.

Adding a Member during PushTalk Communication

Item Operation/Explanation

View PushTalk PB

You can call up a PushTalk Phonebook entry to make a PushTalk call. (See page 80) Instead of pressing

p, press l() to

call.

Pressc to switch between the PushTalk Phonebook List and PushTalk Group List.

View phonebook

You can call up a Phonebook entry to make a PushTalk call.



Call up a Phonebook entryHighlight a

phone number and press

().

Direct input

You can enter a phone number to make a PushTalk call.



Enter a phone number

l

()

View call records

You can call up Dialed Calls/Received Calls to make a PushTalk call.



Dialed calls or Received calls



Select a recordSelect a phone number

l

()

Information

The caller cannot add members if he/she uses a PushTalk compatible model which does not have this function.

For a member who uses a PushTalk compatible model which does not have this function, the members added during PushTalk communication are not shown and a confirmation tone does not sound.

PushTalk

When a PushTalk call comes in, “PushTalk call” is displayed, the ring tone sounds, and the Call/Charging indicator flickers.

“PushTalk group call” is displayed for an incoming group call.

To reject a call, press

( ) during ringing and select “Call rejection”. You can reject the call also by pressing

Pressp to answer a PushTalk call



Talk while pressing p.

You can answer also by

pressing

or Oo()

instead of pressing

. You can

answer also by pressing

with

the FOMA phone closed.

When you get talker’s right, the talker’s right obtained tone is played back. The other party hears your voice only while you are pressing

and having the

talker’s right. When you release

, the talker’s right is

released and a confirmation tone sounds.

You cannot get the talker’s right and an error tone sounds, even if you press

when another member

has it.

“Setting when opened” and “Record message setting” become invalid.

Press

to end the communication after

talking.

A tone for confirming the end of communication sounds at the other end.

When the call you received is a group call, the PushTalk communication itself continues even if you press

, and the icon indicating that you are not participating appears on each member’s display and a confirmation tone sounds. However, when all the members exit, the PushTalk communication itself ends.

Receiving a PushTalk Call

Information

The talker is charged a communication fee from when he/ she presses

and the talker’s right obtained tone sounds.

Just after purchase, Hands-free is automatically activated by “Hands-free w/ PushTalk” (see page 81). However, Hands-free is deactivated during Manner Mode regardless of “Hands-free w/ PushTalk”.

The FOMA phone works according to “Setting when folded” if you close it during communication. You can set also by pressing

( ) and selecting “Set. when folded”.

(See page 63)

You cannot use “On hold” or “Holding” function for PushTalk.

A PushTalk call that comes in during a voice call, a PushTalk call that comes in during Public Mode (Drive Mode), and a voice call (when “PushTalk arrival act” is set to other than “Answer”), a videophone call, data communication, or a PushTalk call that comes in during PushTalk communication are recorded as missed calls in Received Calls.

A PushTalk call that comes in during a videophone call or during data communication does not work and is not recorded in Received Calls.

After you finish PushTalk communication or when you cannot answer to a PushTalk call, you can use a received call record to make a PushTalk call and to re-participate or participate midway in the communication so long as the PushTalk communication continues among other members. If the PushTalk communication among other members has already been finished, your call is dialed as a new PushTalk call.

When a caller adds members during PushTalk communication, the added members are not stored in Received Calls.

See page 82 for how to respond to the PushTalk call during i-mode communication.

When the caller is defined as the one to be rejected, the call is rejected. The setting of call rejection applies to the setting for both voice calls and videophone calls.

When a PushTalk call comes in during Lock All or Omakase Lock, “ ” appears after the lock is released.

Information

PushTalk

From the items stored in a FOMA phone’s Phonebook entry, you need to store a name (reading) and a phone number in the PushTalk Phonebook. You can store up to 1,000 entries in the PushTalk Phonebook.

pm

()



Do the following operations.

You can store also by selecting <New>.

If you store multiple phone numbers from a Phonebook entry, the phone number previously stored in the PushTalk Phonebook is overwritten.

Store in PushTalk Phonebook

Storing in PushTalk Phonebook

PushTalk

Phonebook List

Item Operation/Explanation

View phonebook

You can access an entry already stored in the FOMA phone’s Phonebook and store it in the PushTalk Phonebook.



Call up a Phonebook entry



Select a phone numberYES

Direct input

You can store the entry in the PushTalk Phonebook after storing it in the FOMA phone’s Phonebook.



PhoneSelect a storing method.

New

. . . Go to step 2 on page 84.

Add

. . . Go to step 3 of “Storing Displayed

Phone Number/Mail Address in Phonebook” on page 88.

When multiple phone numbers are stored in a Phonebook entry, press

( ) and select the phone number you want to store in the PushTalk Phonebook. The “

★

” mark is added to the phone number that has already been stored in the PushTalk Phonebook.

View call records

You can access a dialed call record or received call record to store it in the PushTalk Phonebook. You cannot store in the PushTalk Phonebook from the dialed/received call record of the party who is not stored in the FOMA phone’s Phonebook.



Dialed calls or Received calls



Select a recordSelect a phone number



YES

Information

In the PushTalk Phonebook, you cannot store the Phonebook entries set to B by Phonebook 2in1 Setting.

You can store PushTalk Phonebook entries in groups. You can store up to 19 members per group and create up to 10 groups.

PushTalk Phonebook List

c

()

Press c( ) to show the PushTalk Phonebook List.

Select a group

m

()



Put a check mark for members to be stored

l

()

You can store also by selecting <Edit group members> from the Group Member List.

Store in Group

PushTalk Group List

Group Member List Group Member

Selection display

Function Menu of the Group Member Selection Display

Function menu

Operation/Explanation

Members to store

You can display only members applied with a check mark.

PressOo( ) to store the members to the group.



Select a search method.

Reading?

. . . See page 89.

Group?

. . . . See page 89.



Select a member.

You can display the Group Member Selection display with the searched members selected.

PushTalk

You can make a group call to up to four members using the PushTalk Phonebook or PushTalk group.

PushTalk Phonebook List



Put a check mark for members you want

to make a call to

p

or l()

Pressc( ) to show the PushTalk Group List.

When you do not check any members, the call is made to the highlighted member.

PushTalk Group List



Select a group.

Select a group and press p or

( ) to make a call to all

the members in the group.

Pressc( ) to show the PushTalk Phonebook List.

Put a check mark for members you want to make a call to

p

or l()

When you do not check any members, the call is made to the highlighted member.

Making a PushTalk Call Using PushTalk Phonebook

PushTalk Phonebook List

Make a Call from PushTalk Group

PushTalk Group List

Group Member List

Information

When five or more members are stored in a group, you cannot make a call to all the members by selecting the group.

PushTalk Phonebook List

i

()



DEL from P-Talk PB



Do the following operations.

PushTalk Group List

i

()



DEL from PT groupYES

Group Member List

i

()



DEL group members



Do the following operations.

Delete from PushTalk Phonebook

Deleting PushTalk Phonebook Entries

Item Operation/Explanation

Delete this



Select a deleting method.

DEL from P-Talk PB

. . . Deletes an entry in the PushTalk

Phonebook only. Does not delete the entry in the FOMA phone’s Phonebook.

DEL from all PBs

. . . Deletes an entry in both the PushTalk

Phonebook and FOMA phone’s Phonebook.



YES

Delete all



Enter your Terminal Security CodeYES

The FOMA phone’s Phonebook entries are not deleted.

Delete from PushTalk Group

Delete Group Members

Item Operation/Explanation

Delete this



YES

Delete all



Enter your Terminal Security CodeYES

Information

Even when you delete PushTalk groups or group members, the PushTalk Phonebook entries and FOMA phone’s Phonebook entries are not deleted.

PushTalk

Making Full Use of PushTalk Phonebook

Function Menu of the PushTalk Phonebook List/ PushTalk Group List/Group Member List

Function menu

Operation/Explanation

Members to call

When the PushTalk Phonebook List or Group Member List is displayed, you can display the checked members only.

Press p or Oo( ) to make a PushTalk call.

Press i( ) to select “Notify caller ID” and then you can select whether to notify your phone number. When “Cancel prefix” is selected, the FOMA phone works according to the setting by “Caller ID notification”.

Search PushTalk PB

[Phonebook List only]



Select a search method.

Reading?

. . See page 89.

Group?

. . . . See page 89.



Select a member.

You can display the PushTalk Phonebook List with the searched members selected.

Store in P-Talk PB

[Phonebook List only]

See page 79.

DEL from P-Talk PB

[Phonebook List only]

See page 80.

Edit group members

[Group List/ Member List]

You can edit the members in the group. Go to step 2 on page 79.

Edit group name

[Group List only]



Enter a group name.

You can enter up to 16 full-pitch/32 half-pitch characters.

DEL from PT group

[Group List only]

See page 80.

DEL group members

[Member List only]

See page 80.

Auto answer set.

See page 81.

Ring time setting

See page 81.

Hands-Free

See page 81.

m

SettingsPushTalk



Do the following operations.

Set. when folded

See page 63.

i-mode arrival act

See page 82.

P-Talk arrival act

See page 81.

Network connection

You can connect to the network to use PushTalkPlus. This is available only when you have singed up for PushTalkPlus. (See page 76)

Setting PushTalk Calling/Receiving

Function menu

Operation/Explanation

Item Operation/Explanation

Auto answer setting



Select an item.

. . . . Automatically answers immediately

after receiving regardless of “Ring time setting”.

OFF

. . . Does not answer automatically.

Ring time setting



Enter a ring time (seconds).

Enter two digits from “01” through “60”.

“Disconnected” is displayed at the other end after the ring time has elapsed.

Hands-free w/ PushTalk

You can set whether to hear the other party’s voice from the speaker or from the earpiece for when PushTalk communication starts.



ON or OFF

See page 60 for how the FOMA phone works while Hands-free is activated and how to switch to Hands-free during communication.

PushTalk arrival act



Select an item.

Voice mail

. . . Connects an incoming voice call to the

Voice Mail Service Center.

Call forwarding

. . . Forwards an incoming voice call to the

forwarding destination.

Call rejection

. . . Rejects an incoming voice call and does

not answer.

Answer

. . . Shows the Voice Call Receiving display.

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

PushTalk

You can set whether to show the PushTalk Call Receiving display when a PushTalk call comes in during i-mode communication.

i

i-mode settingsi-mode arrival act



Select an item.

PushTalk preferred

. . .Ends i-mode communication and brings up the

PushTalk Call Receiving display.

i-mode preferred

. . .Rejects receiving a PushTalk call and continues

i-mode communication. The call is not recorded in Received Calls.

Information

When you set to “ON”, calls are automatically answered even when the FOMA phone is closed regardless of “Setting when folded”.

When you set to “ON”, calls are automatically answered after switching to Hands-free regardless of “Hands-free w/ PushTalk”.

When you set to “ON”, the ring tone, vibrator, Call/Charging indicator, and backlight do not work. Calls are not automatically answered during Manner Mode.

Even when “ON” is set, Hands-free is deactivated if you open the FOMA phone after you answer a call with the FOMA phone closed.

If you press

-h

for an incoming voice call while “Answer” is set, the Call Receiving display appears after you finish the PushTalk communication, and then you can answer the voice call. To continue the PushTalk communication, press

( ) and select “Call rejection”, “Call forwarding”, or

“Voice mail”.

i-mode Arrival Act

Phonebook

Phonebooks Available for FOMA Phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Storing Phonebook Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Add to Phonebook› 84

Storing Displayed Phone Number/Mail Address in Phonebook . . . . . . . . . . . . . . . . . . . . . . . . 87

Setting Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Group Setting› 88

Dialing from Phonebooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Search Phonebook› 89

Editing Phonebook Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Edit Phonebook› 90

Deleting Phonebook Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Delete Data› 91

Checking Number of Phonebook Entries . . . . . . . . . . . . . . . . . . . . . . . . . . ‹No. of Phonebook› 91

Making Full Use of Phonebooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Making a Call with a Few Touches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Two-touch Dial› 93

Accessing Phonebook Entries by Voice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Voice Dial› 93

Saving (Restoring/Updating) Phonebook to Data Storage Center . . . ‹Data Security Service› 95

Phonebook

You can use two types of Phonebook, namely the Phonebook in the FOMA phone itself, and the Phonebook on the UIM. Use them fully for Phonebook management.

Phonebooks Available for FOMA Phone

FOMA phone

UIM

Number of entries 1,000 entries 50 entries

Contents of Phonebook

Basic item

Name (Reading)

○○

Group 19 groups 10 groups

Phone number 4 phone

numbers

1 phone

number

Phone number icon

○×

Mail address 3 mail

addresses

1 mail

address

Mail address icon

○×

Address

○×

Location information

○×

Birthday

○×

Memo

○×

Image 100 images

Memory No. From 000 to

999

Setting item

Ring tone

○

Vibrator

○

Illumination

○

Picture

○

Chara-den 100

Chara-den

images

Mail ring tone

○

Mail vibrator

○

Mail illumination

○

Answer message

○

Restrictions

Restrict dialing

○×

Call rejection

Call acceptance

Call forwarding

Voice mail

Secret code

○×

Storage in Secret Mode or Secret Data Only

○×

○

: Can be stored.

: Cannot be stored.

You can set your UIM into another FOMA phone and use the UIM Phonebook entries.

You can store Phonebook entries in the FOMA phone (Phone) or on the UIM.

(for at least one second)Phone or UIM

The Edit Name display appears. Go to step 2 and enter a name.

Do the following operations.

Contents of Group

Name

○○

Ring tone

○×

Vibrator

Illumination

Picture

Chara-den

Mail ring tone

Mail vibrator

Mail illumination

Answer message

Add to Phonebook

Storing Phonebook Entries

FOMA phone

UIM

For the FOMA phone For the UIM

pYou can press No to switch between the “Basic item”

tab and “Settings” tab on the FOMA phone’s Phonebook.

Item Operation/Explanation

<Name>

You can enter the name of the person or company in kanji, hiragana, katakana, alphabetic characters, or numerals.



Enter a name.

For the FOMA phone, you can enter up to 16 full-pitch/32 half-pitch characters. You can enter pictographs and symbols as well.

For the UIM, you can enter up to 10 full-pitch characters/21 half-pitch alphanumeric characters. (Half-pitch katakana characters cannot be entered.) When the entry contains both full-pitch and half-pitch characters, you can store up to 10 characters from the beginning regardless of full-pitch or half-pitch characters.

Phonebook

You can enter the reading in half-pitch katakana, alphabetic characters, or numerals.



Enter a reading.

For the FOMA phone, you can enter up to 32 half-pitch characters. You can enter half-pitch symbols as well.

For the UIM, you can enter up to 12 full-pitch characters/25 half-pitch alphanumeric characters. (Half-pitch katakana characters cannot be entered.) When the entry contains both full-pitch and half-pitch characters, you can store up to 12 characters from the beginning regardless of full-pitch or half-pitch characters.

If the displayed reading is acceptable, you do not need to edit it. However, depending on the characters entered for names or entering method, they are not reflected in the reading.

If you enter “ゎ (reduced size)” or “

ヮ

(reduced size)” for a name, “ワ (half-pitch, regular size)” (for the FOMA phone) and “

ワ

(regular size)” (for the UIM) are displayed in the reading field.

<Group>

In the FOMA phone, 19 groups are available. On the UIM, 10 groups are available.



Select a group.

When the storage is completed with no group selected, the Phonebook entry is stored in “No setting”.

Item Operation/Explanation

You can store up to four phone numbers per Phonebook entry in the FOMA phone. You can set an icon for each phone number to categorize mobile phone numbers, office phone numbers, and so on. You can store only one phone number per Phonebook entry on the UIM.



Enter a phone number.

Enter from the city code for the phone numbers.

You can enter up to 26 digits. However, you can enter up to 20 digits for blue UIMs.

Press and hold

for at least one second to insert a pause (p) into the phone number you store. However, you cannot insert the pause (p) to the beginning of phone number or insert it consecutively. The pause (p) inserted to the end of phone number is not stored.

If you insert “:” in the middle of a phone number, you cannot make a call. However, the phone number is recorded in Redial or Dialed Calls.

You can store the phone number which includes “#” such as that for information service as well.



Select an icon.

If you have stored a phone number in the FOMA phone, another “ <Phone number>” will appear in the Add-to-Phonebook display. To store another phone number, select “ <Phone number>”.

You can store up to three mail addresses per Phonebook entry in the FOMA phone. You can set an icon for each mail address to categorize mobile phone addresses, home addresses, and so on. You can store only one mail address per Phonebook entry on the UIM.



Enter a mail address.

The mail address can consist of up to 50 half-pitch alphabets, numerals or symbol characters.

When the mail address is “phone number@docomo.ne.jp”, store the phone number only.

For the FOMA phone, you can set a secret code as well. (See page 93)



Select an icon.

If you have stored a mail address in the FOMA phone, another “ <Mail address>” will appear in the Add-to-Phonebook display. To store another mail address, select “ <Mail address>”.

Item Operation/Explanation

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Phonebook



Enter a ZIP code



Enter a postal address.

You can enter up to 7 digits for the zip code.

You can enter up to 50 full-pitch/100 half-pitch characters for the postal address. Further, you can enter pictographs as well.

You cannot enter “〒” or “-” (hyphen) in the zip code.



Select an item.

By position loc.

. . . Measures the current location and store

the location information. After checking the location information, press



().

From loc. history

. . . Select a location information detail from

Location History and store it.

Attach from image

. . . Stores the location information from an

image. Select a folder, then the image.

To delete the stored location information, select “Delete location info”.

When you press i( ) during measuring the current location, the confirmation display appears asking whether to display the result obtained so far from the location information.

To cancel measuring the current location, press

or l().

Press l( ) from the confirmation display for the location information to restart measuring in “Quality mode”.



Enter a birthday.

You can enter the birthday from January 1, 1800 through December 31, 2099.

<Memo>



Enter a memo.

You can enter up to 100 full-pitch/200 half-pitch characters. Further, you can enter pictographs as well.

Item Operation/Explanation

<Image>

The stored still image is displayed when you call up the Phonebook entry.



Select an item.

Select image

. . . You can store a still image in Data Box.

Shoot image

. . . You can store the shot still image.

Perform step 2 through step 3 of “Shoot a Still Image” on page 139.

To release the stored still image, select “Release image”.

The size of a still image you can store is Stand-by (480 x 854) or smaller and up to 300 Kbytes in JPEG format or GIF format.

If you store a still image larger than 72 x 54 dots, it is displayed shrunk on the detailed Phonebook display.

If you store a still image larger than 240 x 180 dots, it is displayed shrunk on the Call Receiving display.

When “Disp. PH-book image” is set to “ON”, the stored still image is displayed for an incoming call. However, when another image is stored in the “Picture” field, that image is preferentially displayed for the incoming call.



Enter a memory number.

Enter a three-digit number of “000” through “999”.

The lowest empty memory number “010” through “999” is entered in advance. If “010” through “999” are all occupied, the lowest empty memory number from “000” through “009” is entered.

You can set a ring tone for when a voice call or videophone call comes in from the person stored in the Phonebook.



Select ring tone

Go to step 2 on page 98.

To release the stored ring tone, select “Release ring tone”.

You can set a vibration pattern for when a voice call or videophone call comes in from the person stored in the Phonebook.



Select vibrator



Select a vibration pattern.

To release the stored vibrator, select “Release vibrator”.

Item Operation/Explanation

Phonebook

Pressl().

If you have not entered any name, “ ” is not displayed and you cannot store the entry.

You can set an illumination color for when a voice call or videophone call comes in from the person stored in the Phonebook.



Select illuminationSelect a color.

To release the stored illumination, select “Release illumination”.

You can set an image to be displayed for when a call comes in from the person stored in the Phonebook.



Select pictureSelect a type of image



Select a folderSelect an image.

To release the stored image, select “Release picture”.

<Chara-den>

The stored Chara-den image is displayed as a substitute image for videophone calls with the person stored in the Phonebook.



Select Chara-den



Select a Chara-den image.

To release the stored Chara-den image, select “Release Chara-den”.

You can set a ring tone for when a mail message comes in from the person stored in the Phonebook.



Select ring tone

Go to step 2 on page 98.

To release the stored mail ring tone, select “Release ring tone”.

You can set a vibration pattern for when a mail message comes in from the person stored in the Phonebook.



Select vibrator



Select a vibration pattern.

To release the stored mail vibrator, select “Release vibrator”.

You can set an illumination color for when a mail message comes in from the person stored in the Phonebook.



Select illuminationSelect a color.

To release the stored mail illumination, select “Release illumination”.

You can set an answer message for Record Message by Phonebook entry.



Select answer message



Select an answer message.

To release the stored answer message, select “Release answer message”.

Item Operation/Explanation

You can store the displayed or selected phone number, mail address, and still image in the FOMA phone’s or UIM’s Phonebook.

■

The Phonebook entries while editing

When the low battery alarm sounds

The Phonebook entry you are editing is saved automatically. The confirmation display appears asking whether to resume editing when you continue editing after charging the battery or when you operate step 1 on page 84 and select the storage location for the interrupted Phonebook entry after changing to a charged battery. Recall . . . You can resume editing the Phonebook entry.

New. . . . . You can edit a new Phonebook entry. In this case,

the interrupted data is retained. If you execute “Add to phonebook” after storing the new Phonebook entry, the confirmation display appears again.

Only the most recently interrupted entry is retained.

If you resume editing the data but then cancel editing without storing it, that data will be abandoned. Once you recall the data, be sure to store it.

If you receive a call or mail

You can respond it leaving the edited data as it is, thanks to the Multitask function. To return to the Phonebook Edit display, press and hold

for at least one second to switch the menu. You can return to the Phonebook Edit display also by ending the call or mail function.

Storing Displayed Phone Number/ Mail Address in Phonebook

Operation

Storable items

While a phone number is entered Phone number

While a redial item, dialed call record, or received call record is displayed

Phone number

While Sent Address or Received Address is displayed

Phone number/ Mail address

While a site or screen memo is displayed

Phone number/ Mail address

While the text of Message R/F or mail is displayed

Phone number/ Mail address

While the data scanned by Bar Code Reader or Text Reader is displayed

Phone number/ Mail address

While a ToruCa file is displayed

Phone number/ Mail address

While your current location or location history is displayed

Location information

While a registered LCS client is displayed Name/

Phone number

While the Still Image List or a still image is displayed

Still image

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Phonebook

Bring up/Select an item to be stored

i

()



Add to phonebook

To store the address of the sender (or of another recipient of simultaneous mail) of the received mail or the destination address of the sent mail into the Phonebook, select “Store address”. When the addresses of the sender and another recipient of simultaneous mail are found or the multiple destination addresses are found, the display for selecting an address appears. Use

to select the

mail address or phone number you want to store.

To store the results scanned by Text Reader in a Phonebook entry, select “Store phone No.” or “Store mail add.”.

To store a still image in the Phonebook, select “Phonebook” from “Set display”.

When “Add to phonebook” is displayed on the Scanned Code Result display for Bar Code Reader, select “Add to phonebook”; then other information in the scanned code than the phone number or mail address is entered into each field.

Phone or UIMSelect a storing method.

New

. . Go to step 2 on page 84.

Add

. . . Adds data to the existing Phonebook entry. When

storing data on the UIM, “Overwrite” is displayed.

Select a search method



Search the Phonebook



Select a Phonebook entry to be stored

Oo

()

The phone number or mail address is entered automatically.

See step 2 on page 84 to edit other items in the Phonebook entry.

When you store into the FOMA phone’s Phonebook, you can remain the original entry and store a new entry into a different location by changing the memory number.

()



YES

If you store the entry in the UIM Phonebook, select “Overwrite” to overwrite the original entry, or select “Add” to store it as a new entry.

You can sort Phonebook entries into groups such as “Company”, “Friend” etc. according to your relationship, or “Baseball”, “Ceramic art” etc. according to your interest. You can use the sorted Phonebook entries as separate Phonebooks for easy access to the entry you want to search for. You can set a ring tone, vibration pattern, or illumination by group.

m

PhonebookGroup setting

The groups on the UIM are indicated by “ ”.

To reset the group names and respective settings by group, which have already been stored, press

( ), select “Reset group”, and then select

“YES”.

Highlight a group and press l()



Select an item to be setSet the contents.

When you select “ Group name”, enter a group name. You can store up to 10 full-pitch/21 half-pitch characters. However, you can store only up to 10 characters (regardless of full-pitch or half-pitch characters) when you enter both full-pitch and half-pitch characters for a UIM group name.

See step 2 on page 84 for the operations of the other items. However, you cannot set for groups on the UIM.

Select a stored group, or press i( ) and select “Check setting” to check its settings. However, you cannot check the settings of the groups on the UIM.

Press l().

Information

The Phonebook entry does not store the information of “Notify caller ID” included in Redial/Dialed Calls. To set Caller ID Notification, add “186”/“184” to the phone number and store it.

Characters that cannot be stored may be replaced by spaces or deleted, and then stored.

You may not be able to store the information from some sites into the Phonebook.

Group Setting

Setting Groups

Phonebook

You can retrieve stored Phonebook entries by eight search methods.

Xo

Do the following operations.

The display for the same search method as the previous one appears once you have carried out a search. Press

to show the Search Phonebook display.

Search Phonebook

Dialing from Phonebooks

Search Phonebook

display

Item Operation/Explanation

All?

You can bring up all Phonebook entries.

The tabs appear on the top of the Phonebook List. (See page 90)

Reading?

You can enter the reading of the other party’s name from the first character and search. You do not need to enter the full reading.



Enter a part of the reading

Bo

The tabs appear on the top of the Phonebook List. (See page 90)

Group?

You can bring up Phonebook entries stored in the specified group.



Select a group.

The tabs appear on the top of the Phonebook List. (See page 90)

If you press i( ) on the Group List, the Function menu for “Group setting” is displayed.

Memory No.?

[FOMA phone only]

You can search for the entry by the memory number assigned when it was stored in the Phonebook.



Enter the memory number.

Enter from “000” through “999” in three digits.

The tabs appear on the top of the Phonebook List. (See page 90)

From the Stand-by display, you can press

and then press Bo to display the Memory No. Dial display. From there you can make a voice call by entering the memory number of the phone number.

Name?

You can enter the other party’s name from the first character and search. You do not need to enter the full name.



Enter a part of the name

Bo

Phone number?

You can enter a part of the other party’s phone number and search. You can search for the entry even from the middle of phone number.



Enter a part of the phone number

Bo

You can display the Phonebook List also by entering a part of the phone number from the Stand-by display or the “Talking” display, and pressing

Select an entry

d

()

When the entry contains multiple phone numbers, or when you searched by “Mail address?”, press

from

the detailed display to select a phone number.

You can make a videophone call by pressing

( ) or PushTalk call by pressing p.

Mail address?

You can enter a part of the other party’s mail address and search. You can search for the entry even from the middle of mail address.



Enter a part of the mail address

Bo

2-touch dial?

[FOMA phone only]

You can bring up the list of Phonebook entries in memory number 000 through 009.

Phonebook entries not yet stored or being

set with secret are displayed as <

−−−

Item Operation/Explanation

Information

In a search method other than “Group?” and “2-touch dial?”, enter nothing and press

+Bo

; then you can search all

through the Phonebook.

When no Phonebook entry is found that matches the condition you entered by “Reading?” or “Memory No.?”, the entry that is the closest to the condition is displayed.

■

Search order

The Phonebook entries are searched in the order of readings you entered for storing, as follows:

“Space at the beginning of the reading”

→

“Japanese

syllabary (

ア、イ、ウ、エ、オ、

... ン)”→ “Alphabet (A, a,

B, b, ...Z, z)”

→

“Numerals (0 through 9)” → “Symbols”

→

“No reading”. For “All?” and “Reading?”, searching is done in the following order:

“Japanese syllabary (

ア、イ、ウ、エ、オ、

... ン)”

→

“Alphabet (A, a, B, b, ...Z, z)” → “Space at the beginning of the reading”

→

“Numerals (0 through 9)” → “Symbols”

→

“No reading”.

※

The Memory No. Search searches in the order of the memory numbers.

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Phonebook

■

About Phonebook List

When you search from “All?”, “Reading?”, “Group?”, or “Memory No.?”, the tabs appear on the top of the Phonebook List. With “All?” and “Reading?”, the entries are sorted by every column of reading, with “Memory No.?” by every 100 of the memory number, and with “Group?” by every group. Press

to display the Phonebook entries in the tab at left or right. However, when there are 12 or more Phonebook entries in a tab, pressing

(), c(), or

brings up the previous or next page.

After you search by “Reading?”, you can move the cursor

to the “

ア

” through “ワ”, “英”, and

“

他

” tab by pressing each numeric key from the List. When

you successively press the same numeric key, you can move the cursor within the same column.

<Example> Press

to display the “ナ” tab. Each time

you press

, the cursor moves to the top

of “

ニ

” “ヌ” and so on.

After you search by “Group?”, you can move the cursor to the top of each column in the tab by pressing each numeric key from the List. When you successively press the same numeric key, you can move the cursor within the same column. <Example> Press

to move the cursor to the top of

the “

ナ

” column. Each time you press

the cursor moves to the top of “

ニ

” “ヌ” and so

on.

After you search by “Memory No.?”, you can move the cursor to the “000~” to “900~” tab by pressing each numeric key from the List. <Example> Press

to move the cursor to the “500~”

tab.

You can make a voice call to the phone number stored for the name highlighted on the Phonebook List, by pressing

. Also, press l( ) to make a videophone call

and press

to make a PushTalk call. When multiple phone numbers are stored for the name, the one stored first will be dialed.

“ ” appears for the Phonebook entries set to A by Phonebook 2in1 Setting, “ ” appears for the Phonebook entries set to B, and “ ” appears for the Phonebook entries set to common data. (Only in Dual Mode)

Phonebook List

Detailed Phonebook display

m

()



Select an item to be edited



Edit the contents.

See step 2 on page 84 for how to edit the Phonebook entry.

Even if you edit the Phonebook entry in the FOMA phone (Phone), you can remain the original contents in the original location and store the edited contents in the different location by changing the memory number.

■

About the detailed display

UseNo to highlight a tab, then the detailed contents are displayed.

For the Phonebook entry stored on the UIM, “ ” is displayed on the memory number field.

When Notify Caller ID is set to “Notify caller”, “ ” appears, and when set to “Don’t notify”, “ ” appears.

Under the still image, “ ” appears for the Phonebook entries set to A by Phonebook 2in1 Setting, “ ” appears for the Phonebook entries set to B, and “ ” appears for the Phonebook entries set to common data. (Only in Dual Mode)

When a Phonebook entry contains the setting for Multi Number or Chaku-moji, the set contents are displayed in the Item List/Phone Number display.

Item list

The first stored phone number, mail address, postal address, birthday, and memo are displayed.

Phone number

Mail address

When you select the item, you can compose an i-mode mail message with that mail address entered into the address field.

Personal information

When you select a postal address, memo, or still image, the full display appears. Press

Oo()

to return to the former display. When you select the location information, the Function menu of the location information appears. (See page 232)

Settings

When you select each item, a demo is played back. Press

Oo()

to end the demo.

Edit Phonebook

Editing Phonebook Entries

Detailed Phonebook

display (Item List)

Group Reading

Name

Memory No.

Still image

Notify caller ID

Phonebook

()



YES

If you edited the UIM Phonebook entry, select “Overwrite” to overwrite the original contents, or “Add” to save the contents as a new entry.

Detailed Phonebook display

i

()



Delete dataSelect an itemYES

You can delete an item highlighted by pressing

from the detailed display or delete the Phonebook entry.

Phonebook List

i

()



Delete dataDo the following operations.

Delete Data

Deleting Phonebook Entries

Delete from the Detailed Phonebook Display

Delete from the Phonebook List

Item Operation/Explanation

Delete this



YES

Delete selected



Put a check mark for Phonebook entries

to be deleted

l

()



YES

You can check or uncheck all items by pressing

( ) and selecting “Select all in tab/Select all/Release all in tab/ Release all”.

Perform the same operation as that of “Delete all” when you have selected all Phonebook entries including secret ones.

Delete all in tab

You can delete all the Phonebook entries for the displayed tab.



YES

Delete all

You can delete all Phonebook entries including secret entries.



Enter your Terminal Security CodeYES



YES

Information

When you delete a Phonebook entry that is stored in the PushTalk Phonebook, the PushTalk Phonebook entry is also deleted.

m

PhonebookNo. of phonebook

Phone Phonebook . . . The number of Phonebook entries stored

in the FOMA phone (Phone)

Secret . . . . . . . The number of Phonebook entries stored

as secret data during Secret Mode or Secret Data Only

Image . . . . . . . The number of Phonebook entries in

which still images are stored

Chara-den . . . The number of Phonebook entries in

which Chara-den images are stored

PushTalk . . . . The number of Phonebook entries stored

in the PushTalk Phonebook

Voice dial . . . . The number of Phonebook entries set as

voice dial entries

Rest . . . . . . . . : The number of phone numbers that

can still be stored

: The number of mail addresses that

can still be stored UIM Phonebook . . . The number of Phonebook entries stored

on the UIM

No. of Phonebook

Checking Number of Phonebook Entries

Information

While you are using 2in1, the number of displayable Phonebook entries for each mode is displayed. (See page 375)

Making Full Use of Phonebooks

Function Menu of the Phonebook List

Function menu

Operation/Explanation

New

You can store a new Phonebook entry. Go to step 1 on page 84.

Sort

You can change the display order.



Select a type of order.

You can sort Phonebook entries in reverse order by selecting “Ascending” or “Descending”.

You cannot sort on the Phonebook List with tabs displayed.

Attach to mail

You can send i-mode mail with the Phonebook entry attached. Go to step 2 on page 172.

Send Ir data (Send phonebook)

See page 305.

Send Ir data (Send all phonebook)

See page 305.

transmission (Send phonebook)

See page 306.

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Phonebook

transmission (Send all phonebook)

See page 307.

Send to Bluetooth (Send phonebook)

You can send the Phonebook entry using Bluetooth.



Send phonebook



Select a Bluetooth device to be sent



YES

When no Bluetooth devices are registered, the confirmation display appears asking whether to search.

See page 350 for registering and connecting Bluetooth devices.

Send to Bluetooth (Send all phonebook)

You can send all Phonebook entries using Bluetooth.



Send all phonebook



Select a Bluetooth device to be sent



Enter your Terminal Security CodeYES

When “Session number setting” of “Bluetooth settings” is set to “ON”, enter your Terminal Security Code and then a session number.

When no Bluetooth devices are registered, the confirmation display appears asking whether to search.

See page 350 for registering and connecting Bluetooth devices.

Copy to microSD

See page 295.

Connect to Center

See page 95.

Delete data

See page 91.

Character size

You can switch the character size for the list between Large and Standard.

The setting here applies to “Phonebook” of “Character size”.

Set secret/ Release secret

You can activate/deactivate Secret for the Phonebook entry.

If you select “Set secret” in ordinary mode (not in “Secret mode” or “Secret data only”), enter your Terminal Security Code.

Information

You cannot send Phonebook entries from the UIM.

See page 348 for the Bluetooth.

Function Menu of the Detailed Phonebook Display

Function menu

Operation/Explanation

Function menu

Operation/Explanation

Notify caller ID

See page 47.

Prefix numbers

See page 59.

Int’l dial assist

See page 58.

2in1 dial

You can select a phone number to be notified to the other party in Dual Mode of 2in1. (See page 374)

Multi number

You can select a phone number to be notified to the other party. (See page 372)

Chaku-moji

See page 55.

Restrictions

See page 127.

Edit data

Go to step 1 on page 90.

Delete data

See page 91.

Store in P-Talk PB

You can store the phone number in the PushTalk Phonebook.

Add desktop icon

See page 114.

Compose message

You can compose i-mode mail to send to the mail address. Go to step 3 on page 172.

Compose SMS

You can compose an SMS message to send to the phone number set as the destination address. Go to step 3 of “Composing SMS Messages to Send” on page 206.

Attach to mail

You can send i-mode mail with the Phonebook entry attached. Go to step 2 on page 172.

Send Ir data (Send phonebook)

See page 305.

Send Ir data (Send all phonebook)

See page 305.

transmission (Send phonebook)

See page 306.

transmission (Send all phonebook)

See page 307.

Send to Bluetooth (Send phonebook)

See page 92.

Send to Bluetooth (Send all phonebook)

See page 92.

Copy to microSD

See page 295.

Connect to Center

See page 95.

Copy name

You can paste the copied text to a mail message and others.

Function menu

Operation/Explanation

Phonebook

Copy phone number/ Copy mail add./ Copy address/ Copy location info/ Copy birthday/ Copy memo

From the detailed display, press Mo to highlight an item to be copied. The items in the Function menu differ depending on the highlighted items in the Phonebook entry.

You can paste the copied text to a mail message and others.

Secret code

You need to add the recipient’s secret code when sending i-mode mail to anyone who has registered a secret code. Once you set the secret code for the mail address in the Phonebook entry, it will be added automatically whenever you send mail to that address.



Enter your Terminal Security Code



Set code

From the detailed display, press Mo to highlight a phone number or mail address to be set with a secret code.

To check the secret code, select “Check code”.

To release the secret code, select “Release code”.



Enter a four-digit secret codeYES

In the Function menu, “Secret code” is

indicated by “

★

”, after it is set.

Enter a four-digit number for secret code. You cannot set “0000”.

Character size

See page 92.

Set secret/ Release secret

See page 92.

Copy to UIM/ Copy from UIM

See page 346.

Select image

See page 72.

Function menu

Operation/Explanation

When the entry is stored in memory number “000” through “009” in the FOMA phone’s Phonebook, you can dial the phone number just by pressing the lowest one digit of memory number and

Numeric key (

)

d

or Oo()

You can make a videophone call by pressing

( ) or a PushTalk call by pressing p.

Just vocalize the other party’s voice dial name and then the Phonebook entry is accessed for making a call.

You can store up to 100 voice dial entries selecting from among the Phonebook entries stored in the FOMA phone (Phone).

m

PhonebookPhonebook settings



Voice dial setting<New>

You can edit the stored voice dial name by pressing

( ). Go to step 3.

To delete the stored voice dial entry, press i() and select “Delete” or “Delete all” and then select “YES”.

Information

You cannot set secret codes for UIM Phonebook entries.

The secret code can be added only when the recipient’s mail address is in the form of “phone number” or “phone number@docomo.ne.jp”. It cannot be added to any other form of mail address.

If you have stored the mail address as “phone number

＋

secret code@docomo.ne.jp”, you cannot reply to mail messages from the party of that mail address. After changing the mail address to “phone number@docomo.ne.jp”, set the secret code.

Two-touch Dial

Making a Call with a Few Touches

Information

When the Phonebook entry contains multiple phone numbers, the first phone number will be dialed.

When you set “Restrict dialing” to a Phonebook entry of memory number 000 through 009, set it to the first phone number in the Phonebook entry.

When you store a Phonebook entry of memory number from 000 through 009 as secret data, make a call to that entry in Secret Mode or Secret Data Only.

Voice Dial

Accessing Phonebook Entries by Voice

+m-2-6

Voice Dial Setting

ᵡᶍᶌᶒᶇᶌᶓᶃᶂ

Phonebook

Search the Phonebook



Select a Phonebook entry.

The display for search method you used last time appears.

The “★” mark is added to the Phonebook entry stored in the Voice Dial List.

Enter a voice dial name.

You can enter up to 22 half-pitch katakana characters.

The reading (katakana only) of the Phonebook entry is displayed as the voice dial name. Correct the name to the easy-to-identify words.

By your voice, you can access the Phonebook entry you set in the Voice Dial List. When “Read aloud settings” is set to “ON” and “Voice dial” is checked, the operation is guided by the voice guidance.

(for at least one second)As soon as the voice recognition start tone sounds, vocalize the voice dial name.

Start vocalizing within seven seconds after the voice recognition start tone sounds. Once the voice is recognized as a voice dial entry, the detected result is displayed.

You cannot change the volume of the voice recognition start tone. The voice recognition start tone does not sound during Manner Mode.

If you say the word “

ボイス検索

(Boisukensaku)”, “

使い

かたナビ

(Guide)” starts up. Go to step 2 on page 37.

If you say the word “

ボイス設定

(Boisusettei)”, the

display of “Voice settings” appears. (See page 95)

When “Auto voice dial” is set to “ON”, the display for Auto Voice Dial appears after the voice is recognized as a voice dial entry. Then about two seconds later, the FOMA phone automatically dials out.

Highlight a detected result and press

d

().

The first phone number in the selected Phonebook entry is dialed.

You can bring up the detailed Phonebook display by

pressing l( ). Highlight a phone number and

press

or Oo( ) to make a voice call. Also,

you can make a videophone call by pressing

( ) or a PushTalk call by pressing p.

Information

The voice dial name set by this function is effective only for calling up a voice dial entry. For the voice guidance function, the reading (name) stored in the Phonebook is read aloud.

When multiple similar voice dial names are stored or when the voice dial name is short, the recognition rate lowers and a wrong voice dial entry (Phonebook entry) might be accessed. In this case, rename the existing voice dial name and store it.

You cannot store “

ボイスケンサク

(Boisukensaku)” and “

ボ

イスセッテイ

(Boisusettei)” as a voice dial name.

Dial from Phonebook by Voice

You need to set “Voice earphone dial” to “ON” and open the FOMA phone in advance.

Press and hold the switch of the Flat-plug Earphone/Microphone with Switch for at least one second.

Perform the operations in step 1 and step 2 of “Dial from Phonebook by Voice” on page 94.

You can make a call also by pressing the switch of the Flat-plug Earphone/Microphone with Switch instead of pressing

or Oo.

You can access a voice dial entry with the FOMA phone closed as well. You need to set “Voice earphone dial” to “ON” in advance, and connect with the Bluetooth device using the Headset service or Hands-free service.

For using the Hands-free service, the Bluetooth device needs to support a voice recognition function.

Press the switch of the Bluetooth device.

Press and hold the switch of the Bluetooth device or

of the FOMA phone for at least one second when the FOMA phone is closed.

Access a voice dial entry following the voice guidance.

Once the voice is recognized as a voice dial entry, the detected result is displayed on the Private window.

The FOMA phone automatically dials out about two seconds after the voice guidance to that effect finishes.

Information

When you vocalize, keep your mouth away from the microphone about 10 cm. If your voice is too distant, it may be difficult to recognize your voice.

Pronounce the voice dial name as clearly as possible.

Before and after voice production, avoid making the sounds unrelated to the voice dial name such as clearing your throat, clicking your tongue, noisy breathing or other noise.

Vocalize in quiet, noise-free locations.

While vocalizing, do not put your fingers over the microphone, or press or brush the keys.

To access a voice dial entry using the Flat-plug Earphone/Microphone with Switch

To access a voice dial entry using a Bluetooth device

Phonebook

m

SettingsOther settings



Voice settings



Do the following operations.

You can save the Phonebook stored in your FOMA phone to the Data Storage Center. By accessing the Data Storage Center, you can restore/update the Phonebook to your FOMA phone. Data Security Service is a pay service that is available on a subscription basis.

You cannot use Data Security Service when you are out of the service area.

For details on Data Security Service, refer to “Mobile Phone User’s Guide [i-mode]”.

m

LifeKitData Security Service



Do the following operations.

Voice Settings

Item Operation/Explanation

Auto voice dial

You can automatically make a call to the phone number accessed by voice.



ON or OFF

Voice earphone dial

You can access the voice dial entries by using the Flat-plug Earphone/Microphone with Switch (option) or Bluetooth Headset F01 (option).



ON or OFF

Read aloud settings

See page 333.

Read aloud volume

See page 333.

Read aloud speed

See page 334.

Read aloud output

See page 334.

Read aloud valid set.

See page 334.

Data Security Service

Saving (Restoring/Updating) Phonebook to Data Storage Center

Item Operation/Explanation

Connect to Center



Enter your Terminal Security CodeYES

Sent/recv. PB data list

You can display the records of communication such as saving the Phonebook, mail messages, or images to the Data Storage Center.



Select a record.

Select a communication completion time in the list to switch to the detailed display.

On the site of the Data Storage Center, you can set so as to periodically update and save the Phonebook entries in your FOMA phone to the Data Storage Center.

For details, refer to “Mobile Phone User’s Guide [i-mode]”.

PB image sending

You can set whether to save images set for the Phonebook entries to the Data Storage Center.



ON or OFF

Information

You cannot save the UIM Phonebook.

When the Phonebook entries saved to the Data Storage Center exceeds the number of Phonebook entries storable in the FOMA phone’s Phonebook, the excess entries cannot be updated.

Up to 30 records are saved. When more than 30 records are saved, the older records are overwritten.

You cannot save the images whose output from FOMA phone is prohibited.

Auto-update

Information

The Phonebook is not automatically updated while another function is working at the time of Auto-update.

If the Phonebook cannot be updated, the notification icon of “ ” (PB in Center updated) appears on the Stand-by display. Select “ ”, and the update display appears if Auto-update is set. If Auto-update is not set, the update display appears after you enter your Terminal Security Code.

Item Operation/Explanation

Sound/Screen/Light Settings

Sound Settings

Changing Ring Tone of FOMA Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Select Ring Tone› 98

Setting Sound Effects of Ring Tone or Melody . . . . . . . . . . . . . . . . . . . . . . . . .‹Melody Effect› 99

Informing You of an Incoming Call by Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Vibrator› 100

Using Recorded Sound as Ring Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Voice Announce› 100

Changing Calling Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Melody Call Setting› 100

Setting Keypad Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Keypad Sound› 101

Setting Charging-start/end Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Charge Sound› 101

Sounding Alarm when a Line is Likely to be Disconnected . . . . . . . . . . . . . . .‹Quality Alarm› 101

Setting Ring Time for Mail and Messages R/F . . . . . . . . . . . . . . . . ‹Mail/Message Ring Time› 101

Sounding Ring Tone from Earphone Only . . . . . . . . . . . . . . . . . . . . . ‹Headset Usage Setting› 101

Silencing Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Manner Mode› 102

Selecting Manner Mode Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Manner Mode Set› 103

Screen/Light Settings

Changing Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Display Setting› 104

Displaying an Image Stored in Phonebook during Ringing . . . . ‹Display Phonebook Image› 106

Setting Displays for Private Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Private Window› 106

Displaying Arrival Information by Opening FOMA Phone. . . . . ‹Received Mail/Call at Open› 106

Setting Lights for Display and Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Backlight› 107

Adjusting Quality of Display Automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹LCD AI› 107

Setting Quality of Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Image Quality› 107

Setting Color Combination for Display . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Color Theme Setting› 108

Setting Display of Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .‹Menu Icon Setting› 108

Using Kisekae Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Kisekae Tool›109

Using Feel Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Feel Settings› 109

Setting Color of Call/Charging Indicator and Others. . . . . . . . . . . . . . . . . . . . . . ‹Illumination› 111

Checking Missed Calls and New Mail by Tone and Call/Charging Indicator

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Info Notice Setting› 112

Using Icons on Desktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Desktop Icon› 112

Changing Character Font . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Font› 114

Changing Character Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‹Character Size› 115

Setting Clock Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Sound/Screen/Light Settings

You can set ring tones by incoming type. If you select an i-motion movie, the i-motion movie and sound are played back for incoming calls/messages. (Chaku-motion)

The ring tone is the PCM sound source, chord of 128 tones, and ADPCM compliant.

See “Add to Phonebook” for setting a ring tone by Phonebook entry, and see “Group Setting” for setting it by group.

■

Ring Tone List (pre-installed)

+m-1-3

Select Ring Tone

Changing Ring Tone of FOMA Phone

Display Title

The Name of Lyricist/

Composer

Pattern 1

ーー

Pattern 2

ーー

Pattern 3

ーー

Pattern 4

ーー

Pattern 5

ーー

YOU RAISE ME

※1

YOU RAISE ME UPComposer:

LOVLAND ROLF

THIS LOVE

※1

THIS LOVE

Composer: ANGELA AKI

EL COLIBRI EL COLIBRI

Composer: SAGRERAS JULIO S

LA FILLE AUX

CHEVEUX

※1

LA FILLE AUX CHEVEUX DE LIN

Composer: DEBUSSY CLAUDE ACHILLE

SOMEDAY MY PRINCE

SOMEDAY MY PRINCE WILL COME

Composer: CHURCHILL FRNK E

POLET SHMAJA POLET SHMAJA

Composer: RIMSKIJ KORSAKOVICH NICOLAS ANDR

RHAPSODY ON A THEME

RHAPSODY ON A THEME OF PAGANINI OP 43

Composer: RACHMANINOFF SERGEI

JAZZ

※1

ーー

3D tone1

※1

ーー

3D tone2

※1

ーー

3D tone3

※1

ーー

3D tone4

※1

ーー

bubble

ーー

waterdrop

ーー

Mail 1

ーー

Mail 2

ーー

CHURAUMI KAKUREKUMANOMI

※2

ーー

※

1 3D sound supported. See page 99 for 3D sound.

※

2 i-motion movie

(Note) Uppercases of Roman alphabet are used for titles,

lyricists, and composers. The name of lyricists and composers are described conforming to the JASRAC web page. Whole part of long titles may not be displayed due to restriction of the display size.

License No. T-0790001

m

SettingsSoundSelect ring tone



Select an incoming type.

Select an item and press l( ) to check the contents actually played back or displayed.

Select ring toneSelect a type of ring tone.

Melody

. . . . . . . . . . .Sets a melody as a ring tone.

MUSIC

. . . . . . . . . . .Sets a Chaku-uta Full®music file as

a ring tone.

motion

. . . . . . . . .Sets an i-motion movie as a ring

tone. (Chaku-motion/Chaku-uta

)

Voice announce

. . .Sets the sound recorded by “Voice

announce as a ring tone. The setting is completed.

OFF

. . . . . . . . . . . . . .Sets a ring tone off. The setting is

completed.

Select a folderSelect a ring tone.

If you select “MUSIC” in step 2, select “Fullsong ring tone” or “Point ring tone”. (See page 327)

See page 162 when you select “Search by i-mode”.

Information

You can set the Call Receiving display by selecting “Phone” or “Videophone”, and then by selecting “Select calling disp.”. Go to step 2 on page 105.

You can set the Mail Receiving display by selecting “Mail”, “Chat mail”, “MessageR” or “MessageF”, and then by selecting “Select receiving disp.”. Go to step 2 of “Set Stand-by Display” on page 104.

The priority order of ring tones is as follows: “Read aloud

settings”

→

“Setting for Phonebook entry” → “Group setting”

→

“Select ring tone”. When a call comes in to the additional

number, the ring tone specified by “Set as ring tone” of “Multi number” sounds. If a call comes in to Number B while using 2in1, the priority order of the ring tones is as follows: “Read aloud settings”

→

“Setting for Phonebook entry” → “Group setting”

→

“Ringtone set. for No. B” (see page 373).

The ring tone or images set at purchase might be played back or displayed for incoming calls or messages, depending on the combination of this function and “Display setting”.

Foma P905i User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual