Foma D902iS User Manual

Download

Manual for Data Communication

Data communication .......................................................................................... 1

Flow of setup for data communication ............................................................2

Connecting PC to FOMA terminal ..................................................................... 3

Installation of the communication configuration file (driver) ........................ 4

Communicating using the FOMA PC configuration software ........................5

Communicating without using the FOMA PC configuration software ........15

AT command ..................................................................................................... 25

■ About Manual for Data Communication

In this manual, the important items, which are needed for data communication by FOMA D902iS and the method of installing “communication configuration file (driver) for D902iS” and “FOMA PC configuration software” are explained.

■ Operations for Windows

In this manual, the contents correspond to Windows XP Service Pack 2. A part of the operations or screens may differ, depending on the environment.

Data communication

The data communication modes available from FOMA terminal and hints on use are explained.

･ FOMA terminal does not support the Remote

Wakeup.

･ FOMA terminal does not support fax communication. ･ When connecting FOMA terminal to DoCoMo’s

PDA “sigmarion Ⅱ” or “musea” for data communication, make sure to update “sigmarion Ⅱ” or “musea”. For details on update, visit the DoCoMo website.

Supported communication modes

FOMA terminal supports 3 communication modes: packet communication, 64K data communication and data transfer. These communications become available by installing the related software onto a PC from the attached CD-ROM, connecting FOMA terminal to the PC and making required settings.

■ Packet communication

Packet communication charges are based on the amount of data sent and received, which make it suitable for high-speed exchange of relatively small amounts of data such as sending and receiving mail. No communication charges are required when no data are exchanged even if you are connected to the network. Therefore, sending/ receiving data as needed while remaining connected to the network is possible. High-speed packet communication provides a maximum reception speed of 384 kbps and a maximum transmission speed of 64 kbps by using access points that support packet communication on FOMA, such as Docomo’s “mopera U/mopera” Internet connection service. These are offered by Best-effort connection which allows transmission speed to vary with the environment and the rate of congestion. Note that communications of large-size data such as for viewing and downloading websites containing images will require high charges.

■ 64K data communication

The 64K data communications allow data transfer/ reception at stabled communication rate of 64 kbps. Communication charges are based on the duration of the connection to the net work regardless of the volume of data, which make it suitable for sending and receiving relatively large amounts of data as in downloading multi-media contents. You need to use access points that support FOMA 64K data communication such as Docomo’s “mopera U/mopera” Int ern et c onn ec ti on

service or ISDN synchronized 64 kbps access points. Note that communicating for long time will require high charges.

■ Data transfer

It is the mode of non-charged communication in which data are transferred/exchanged via FOMA USB cable (optional). Various data including the phonebook, incoming/outgoing mail and bookmarks are sent/received.

Usage precautions

Internet service provider usage charge

When using the Internet from PC, usage charge to your Internet service provider (hereinafter called provider) is generally required. This charge is paid directly to the provider, and is separate from the FOMA service charge. For more information on usage charges, contact your provider.

･DoCoMo provides 2 Internet connection services:

mopera U and mopera. The mopera U service requires subscription and a monthly fee. It allows you to use broadband Internet connection and international roaming services. There is also a plan that requires a monthly fee only when you use the service. The mopera service, allows you to access the Internet without subscription and monthly fee. You can make a connection with Internet immediately. For details such as on charges, visit the DoCoMo website.

Setting the dialup connection (provider, etc.)

Different dialup connections are required for packet communication and 64K data communication. When performing packet communication, use the dialup connection for FOMA packet communication. When performing 64K data communication, use the dialup connection for FOMA 64 kbps data communication or ISDN synchronized 64 kbps data communication.

･You cannot connect to access points of PHS 64K/

32K data communication such as PIAFS or DoPa .

User authentication during network access

Some dialup connections require user authentication (ID and password) before a connection can be established. If user authentication is required, you must use your communication software or dialup network to enter your ID and password before connection. Your ID and password will be assigned by the provider or network administrator such as inhouse LAN, etc. For more information, contact your provider or network administrator.

Access authentication when using PC browser

To authenticate FirstPass (user certificate), you must install FirstPass PC software from the attached CDROM and configure it. For details, see “FirstPassManual” in the CD-ROM. To view “FirstPassManual” (PDF format), Adobe Reader (version 6.0 or later recommended) is required. If Adobe Reader is not installed in you r PC, you need to download the latest version from th e Adobe Systems Incorporated website (Communication fee is separately required for downloading). For details, see the Adobe Systems Incorporated website.

■ Operating environment for the FirstPass PC

software

Item Requirements

PC PC/AT compatible computer OS The Japanese version of

Memory requirements*

Hard disk capacity*

Browser Microsoft

*1 May vary with the PC system configurations.

Windows 98SE, Me, 2000 or XP Windows 98SE, Me, 2000: 32MB

or more Windows XP: 128MB or more

10 MB or more free disk space

and later version For Windows XP, Microsoft and later version

Internet Explorer 5.5

Internet Explorer 6.0

Conditions of packet communication and 64K data communication

To perform data communication from FOMA terminal, the following conditions must be satisfied.

･The PCs which may use a FOMA USB cable

(optional).

･You must be within the FOMA service area. ･Packet communication requires an access point

that supports FOMA packet communications.

･64K data communication requires an access point

that supports FOMA 64 kbps or ISDN synchronized

64 kbps data communication. However, even when the above requirements are satisfied, you may not be able to perform data communication if base station traffic is heavy, or the signal quality is poor.

● APN (Access Point Name) String to identify a provider, etc. to connect by packet communication. The APN for mopera U is “mopera.net” and mopera is “mopera.ne.jp”.

● cid (Context Identifier) The registration number when writing packet communication dialup connection (APN) information to FOMA terminal. 10 numbers from 1 to 10 are available for FOMA terminal. By default, “mopera.ne.jp” is registered in cid1, and “mopera.net” in cid3.

● W-TCP A TCP parameter designed to fully utilize TCP/IP transmission capacity during packet communications in a FOMA network. This communication setting is essential to enable full use of FOMA terminal capabil ity.

Flow of setup for data communication

The setup work needed to connect FOMA terminal to a PC to perform packet or 64K data communication is as follows:

Install the communication configuration file ☛P4

Connect a PC to FOMA terminal ☛P3

Check the communication configuration file ☛P4

Install the FOMA PC configuration software ☛P6

(Easy Setup) Packet communication setup

● mopera U / mopera ☛P7

● Other providers ☛P8

Execute communication ☛P11 (Disconnect ☛P12)

(Easy Setup) 64K data communication setup

● mopera U / mopera ☛P10

● Other providers ☛P11

Glossary of Data communication

● Administrator privilege A user level that provides complete access to all OS functions in Windows XP and 2000. There must be at least one user that has admini strator p rivileges fo r each PC. A user that has no administrator privileges is not normally allowed to inst all/unin stall dr ivers an d software.

Set up communications without using the FOMA PC configuration software ☛P15

Connect ☛P23 (Disconnect ☛P24)

Communication configuration file (driver)

Install the communication configuration file on a PC from the attached CD-ROM, before connecting FOMA terminal to a PC to perform packet communication or 64K data communication.

FOMA PC configuration software

When the FOMA PC configuration software (found on the CD-ROM) is installed on a PC, a number of settings required for data communication via connection between FOMA terminal and PC can be made from the PC by simple operation.

Checking operating environment

Use the communication configuration file and the FOMA PC configuration software in the following operating environments:

Item Requirements

PC OS The Japanese version of

Memory requirements

Hard disk capacity 5 MB or more free disk space

*1 USB port (conform to USB specification 1.1/2.0) is

required.

PC/AT compatible computer

Windows 98, Me, 2000 or XP Windows 98, Me: 32MB or more

Windows 2000: 64MB or more Windows XP: 128MB or more

INFORMATION

● Note that utilization may not be possible in certain operating environments. Furthermore, operation will not be guaranteed in an environment other than that described above or by upgrading. And DoCoMo assumes no responsibility for operation under such conditions.

● In this manual, Windows 98 and Windows 98SE are collectively shown as Windows 98.

Connecting PC to FOMA terminal

The connection should be made with the PC and FOMA terminal both switched on.

･Be sure to install the communication configuration

file (driver) before connecting with a PC in communication mode. ☛P4

Connecting a PC

Connect by using the FOMA USB cable (optional).

aOpen the cap on the FOMA terminal’s

external connection terminal

bInsert one end of the FOMA USB cable into

the FOMA terminal’s external connection terminal until it clicks

cInsert the other end of the FOMA USB cable into

the PC USB connector

･ When a PC and FOMA terminal are connected in

communication mode, appears on the display of FOMA terminal.

･ If you connect FOMA terminal to a PC in

communication mode before installing the communication configuration file, Windows may automatically detect that a FOMA USB cable has been inserted, request to install a driver, and the wizard screen will be displayed. In that case, remove FOMA terminal and click (Cancel) to exit the wizard.

キャンセル

Before installation/uninstallation

･

Installing and uninstalling the communication configuration file or the FOMA PC configuration software under Windows XP or 2000 can only be performed by a user with administrator privileges. Attempts made by other users will result in errors. For details on PC administrator privileges, refer to the instruction manual of the P C or conta ct your PC manufacturer or Microsoft Corporation.

･Before starting operation, make sure that no other

program is running. If there is any active program, save and exit the program before operation.

USB connector

Connector (label facing up)

Release button

■ Removing FOMA USB cable

Press release buttons on both sides of the connector for FOMA terminal and pull it out. Pull the connector for PC out from the side of PC.

･ Be sure to press release buttons on both sides

of the connector when pulling it out for FOMA terminal. Forcing to pull it out may cause a malfunction.

Connecting while charging

FOMA terminal can be connected using a desktop holder (optional) during the charging. However, charging time becomes longer.

aConnect the desktop holder to the AC

adapter

･ Plug the AC adapter into the wall outlet

bConnect FOMA terminal and FOMA USB

cable

cAlong with the desktop holder, insert FOMA

terminal at an angle as shown in the figure

･ Pull out the FOMA USB cable in front of the

desktop holder, when inserting FOMA terminal.

･ Check that the Enter key lights in red.

Desktop holder

AC adapter connector ( facing up)

Enter key

FOMA USB cable connector for FOMA terminal (label facing up)

Installation of the communication configuration file (driver)

Install the communication c onfigurat ion file onto a PC before connecting FOMA terminal to the PC to perform communication.

Installing the communication configuration file

Before operation, read “Before installation/ uninstallation” ☛P3

･Perform Steps 1 to 3 first, and then connect

FOMA terminal to a PC.

Insert the attached CD-ROM into a PC

The

ソフトウェアのセットアップ

setup) screen appears.

Click

2 3

通信設定ファイル

configuration file) Click

インストール開始

A screen requesting to connect FOMA D902iS to the PC appears.

Connect FOMA terminal to the PC

A progress screen for installation appears and automatically completed.

･Connect FOMA terminal while the power is on. ･Go to “Checking the communication

configuration file”, and check the type and name of the device installed.

(Software

(Communication

(Start installation)

INFORMATION

● FOMA terminal can be connected in communication mode by using a data communication adapter D01(optional), while charging. However, charging time becomes longer.

● Do not remove the FOMA USB cable during data communication, or give shock to FOMA terminal and desktop holder. It may cause the interruption of charging or data communication, malfunction or failure of PC or FOMA terminal, or loss of data.

● Starting to charge during data communication may not complete charging. To complete charging, it is recommended that you end the data communication first, and then start charging.

INFORMATION

● Installation may take a few minutes.

● When Windows rebooting is prompted on the screen,

follow the instruction and reboot.

● If a PC and FOMA terminal are connected before the communication configuration file is installed, another driver may be automatically installed. When this happens, performing the operation in Step 2 displays a message saying that the installed driver must be uninstalled. In this case, uninstall the driver following instruction shown on the display a nd install the communication config uration file.

Checking the communication configuration file

When the PC does not detect FOMA terminal correctly, settings and communication cannot be performed.

Example

For Windows XP

Click

スタート

ル

(Control Panel), the

メンテナンス

(Start),

コントロールパネ

パフォーマンスと

(Performance and

maintenance) icon and the

システム

(System) icon

The

システムのプロパティ

screen appears.

■ For Windows 2000, Me, 98:

スタート, 設定

a Click

ロールパネル

b Double-click the

Click the

デバイスマネージャ

The

■ For Windows Me, 98: Click the

Double-click a type of each device z

Check the name of the installed device

Check that all the names of installed devices are shown.

USB (Universal Serial Bus) Controller

Port (COM and LPT) or (COM/LPT)

Modem FOMA D902iS

*1 Displayed only under Windows Me and 98. *2 “x” of COMx varies by PC to be used.

ハードウェア

デバイスマネージャ

tab

ネージャ

Device type Device name

(System properties)

(Setting) and

システム

コント

icon

(Hardware) tab z

(Device manager)

screen appears.

デバイスマ

･ FOMA D902iS ･ FOMA D902iS Command* ･ FOMA D902iS Modem* ･ FOMA D902iS OBEX*

･ FOMA D902iS

Command Port (COMx)*

･ FOMA D902iS OBEX Port

(COMx)*

Uninstalling the communication configuration file

Before operation, read “Before installation/ uninstallation” ☛P3 Before uninstalling, make sure that FOMA terminal is removed from the PC.

Example

For Windows XP

Click

スタート

and the

プログラムの追加と削除

コントロールパネル

(Add/

delete Programs) icon

The

プログラムの追加と削除

■ For Windows 2000, Me, 98:

スタート

a Click

ネル

screen appears.

, 設定 and

コントロールパ

b Double-click the

(Add/delete applications) icon

と削除

Select FOMA D902iS USB z Click

と削除

(Update/delete)

･For Windows Me or 98, click

delete).

Check the name of program and click

(Yes)

The uninstall process of the configuration software starts.

Click OK

アプリケーションの追加

変更

追加と削除

(Add/

はい

INFORMATION

● When the installation fails or FOMA D902iS USB is not displayed on the screen of Step 1, insert the attached CD-ROM into the PC, click

on the

ル

uninstall the communication configuration file.

● When the communication configuration file is uninstalled and immediately reinstalled under Windows Me or 98, data communication may not be successful depending on the PC environment. In this case, the FOMA USB cable (optional) should be removed and reinserted before re-attempting data communication.

ソフトウェアのセットアップ

通信設定ファイ

screen and

Communicating using the FOMA PC configuration software

A number of settings are required when FOMA terminal is connected to a PC to perf orm packet communication or 64K data communication. The FOMA PC configuration software allows you to easily perform the following settings:

■ Easy setup

Creating a dialup connection for FOMA data communication and W-TCP setup can be performed automatically by following the instructions in the guide.

■ W-TCP setup

This function optimizes the settings in the PC required for FOMA packet communication. Optimization of the communication settings using W-TCP setup is required to enable communication capability to maximum extent.

■ Dialup connection (APN) setup

This function performs the dialup connection (APN) setup required for packet communication. Unlike 64K data communication, phone numbers cannot be used as a dialup connection for FOMA packet communication. Set a dialup connection name called APN in FOMA terminal for each dialup connection in advance, and enter the registration number (cid) in the phone number field of dialup connection. By default, “mopera.ne.jp” (APN) is registered in cid 1 to connect to mopera, and “mopera.net” (APN) for cid 3 to connect to mopera U, but the APN for connections to other providers and inhouse LAN must be set.

Installing the FOMA PC configuration software

･

Uninstall an old version of the FOMA PC configuration software (version 1.00 or 2.00), if already installed, before installing the FOMA PC configuration software (version 2.0.1) from the attached CD-ROM. You can display the version

メニュー

from information) of the FOMA PC configuratio n software.

･ If the following software (provided with the FOMA

model released before this time’s) are installed, uninstall them in advance

･ W-TCP environment configuration software

(hereinafter called “old W-TCP configuration software”)

･ FOMA data communication configuration

software (hereinafter called “old FOMA data communication configuration software”)

･ Before operation, read “Before installation/

uninstallation” ☛P3

Example

Insert the attached CD-ROM into the PC

The screen appears.

Click PC

software) Click 次へ (Next)

The FOMA PC configuration software license agreement appears.

Read the content of the screen and click

はい

(Menu)→

For Windows XP

ソフトウェアのセットアップ

設定ソフト

if you agree to the agreement

バージョン情報

(Version

(Software setup)

(PC configuration

Check that

(Reside in task tray) is selected and click

タスクトレイに常駐する

W-TCP設定(W-TCP setup) resides in the task tray

after the setup.

･This is recommended for setting and

cancellation of W-TCP communication. (☛P13)

･You can change the setting of resident

software after the installation.

Check the installation path and click

Check the name of the program folder and

click

Click 完了(Done)

FOMA PC software) is started up.

･Settings can be started from this screen.

INFORMATION

● If the FOMA PC configuration software, old W-TCP configuration software, or old FOMA data communication configuration software is already installed, the screen to cancel the installation appears. Click OK to uninstall this software and then install the FOMA PC configuration software.

● When installation, the confirmation screen to cancel the installation appears. To continue the installation, click

設定ソフト

キャンセル

いいえ

. To cancel, click はい and 完了.

(FOMA PC configuration

いいえ

(No) is clicked during

Setting packet communication by easy setup

Before setup, make sure that FOMA terminal and the PC are properly connected. ☛P3

Example

For Windows XP

Click

スタート, すべてのプログラム

programs) ( other than Windows XP), FOMA PC

フト

The FOMA PC configuration software is started up.

プログラム

and FOMA PC

(Programs) for

設定ソフト

(All

設定ソ

Select 『mopera U』

connection) or (mopera connection) z Click

･DoCoMo provides 2 Internet connection

services: mopera U and mopera. The mopera U service requires subscription and a monthly fee. The mopera service requires no subscription and a monthly fee.

･When mopera U is selected, a confirmation

message to agreement appears. If the subscription is completed, click

『

mopera』

への接続

はい

(mopera U

Using mopera U / mopera

･ Using other providers ☛P8

Example

1 2

For Windows XP

Start the FOMA PC configuration software z Click

かんたん設定

Select

パケット通信

communication) z Click

(Easy setup)

(Packet

Click OK on the FOMA

FOMA terminal settings) screen

接続先

(APN)情報 (Dialup connection (APN)

information) is obtained from FOMA terminal. Please wait.

Enter any connection name z Click

･The following characters (one-byte) cannot be

entered: ￥ / : ＊ ? ! <> ｜ 

端末設定取得

(Get

Click

･ The entry for

パスワード

･ For Windows XP or 2000, select the allowable

user. If you select users), all users that are allowed to logon to Windows can access the connection. For Windows Me or 98, (Select allowable user) is not displayed.

ユーザー名

(Password) is not required.

(User name) or

すべてのユーザー

使用可能ユーザーの選択

(All

Click OK

The PC must be rebooted for the changes to take effect. Click reboot the PC.

･If optimization of W-TCP setting has already

been performed, rebooting is not requir ed.

･Performing communication ☛P11

Using other providers

･Using mopera U / mopera ☛P7

はい

when a window prompts you to

Check that

selected and click

･ This screen is not displayed if optimization has

already been performed.

Check the settings and click

最適化を行う

(Optimize) is

完了

Example

For Windows XP

Perform Steps 1 to 4 of “Using mopera U / mopera” of “Setting packet communication by easy setup” ☛P7

･Select

その他

(Others) in Step 3 for the dialup

connection.

Enter any connection name z Click

先

(APN) 設定(Set dialup connection

(APN))

･The following characters (one-byte) cannot be

entered: ￥ / : ＊ ? ! <>｜

接続

■ Advanced setting (TCP/IP setting):

Click

詳細情報の設定

display the IP

ムサーバー

When dialup information is required, register such as addresses, based on the information assigned by the provider,etc.

アドレス

(Name server) setting screens.

(Set detail info) to

(IP address) and

ネー

Set the dialup connection (APN)

By default, “mopera.ne.jp” is registered in cid1, and “mopera.net” in cid3. Register a dialup connection (APN) for cid 2 or 4 to 10.

追加

a Click

The connection (APN)) screen appears.

b In

connection name (APN) of your provider, etc ., which supports the FOMA packet communication z Click OK

The display returns to the screen.

･Only one-byte alphanumeric characters,

Click OK

The display returns to the screen in Step 2. (APN) set in Step 3 appears in (Select dialup connection (APN)).

(Add)

接続先

(APN)

の追加

(Add dialup

接続先

(APN), correctly enter a dialup

接続先

(APN)設定

hyphens ( - ) and periods ( . ) can be entered for

接続先

(APN).

▼

接続先

(APN)

接続先

の選択

Check that

click

･This screen does not appear if optimization has

already been performed.

Check the settings and click

最適化を行う

is selected and

完了

Check the dialup connection name (APN) of

接続先

(APN)

の選択

and click

Enter the user name in

password in

･ Enter the user name and password assigned

by the provider, etc. correctly. Be careful about the upper/lower case of each character.

･ For Windows XP or 2000, select the allowable

user. If you select that are allowed to logon to Windows can access the connection. For Windows Me or 98,

使用可能ユーザーの選択

パスワード

ユーザー名

すべてのユーザー

is not displayed.

z Click

and the

, all users

Click OK

The PC must be rebooted for the changes to take

はい

effect. Click reboot the PC.

･If optimization of W-TCP setting has already

been performed, rebooting is not requir ed.

･Performing communication ☛P11

when a window prompts you to

Setting 64K data communication by easy setup

Before setup, make sure that FOMA terminal and the PC are properly connected. ☛P3

Using mopera U / mopera

･ Using other providers ☛P11

Example

For Windows XP

Perform Steps 1 to 3 of “Using mopera U / mopera” of “Setting packet communication by easy setup” ☛P7

･ Select 64K

in Step 2 for the communication procedure.

データ通信

(64K data communication)

Click

･The entry for

required.

･When the OS is Windows XP or 2000, select

the allowable user. If you select

ザー

Windows can access the connection. For Windows Me or 98, is not displayed.

ユーザー名

, all users that are allowed to logon to

パスワード

すべてのユー

使用可能ユーザーの選択

is not

Enter any connection name and select the

modem z Click

･ The following characters (one-byte) cannot be

entered: ￥ / : ＊ ? ! <> ｜

･ Check that FOMA D902iS is set for

(Modem selection).

択

モデムの選

Check the settings and click

Click OK

･Performing communication ☛P11

完了

Using other providers

･ Using mopera U / mopera ☛P10

Example

For Windows XP

Perform Steps 1 to 3 of “Using mopera U / mopera” of “Setting packet communication by easy setup” ☛P7

･ Select 64K

communication procedure, and 3 for the dialup connection.

データ通信

in Step 2 for the

その他

in Step

Enter the user name in

password in

･Enter the user name or password assigned by

the provider, etc. correctly. Be careful about the upper/lower case of each character.

･For Windows XP or 2000, select the allowable

user. If you select that are allowed to logon to Windows can access the connection. For Windows Me or 98,

使用可能ユーザーの選択

パスワード

ユーザー名

z Click

すべてのユーザー

is not displayed.

and the

, all users

Set each item z Click

･ Register the following items:

･

接続名

･

モデムの選択

･

電話番号

(Phone number) :

■ Advanced setting (TCP/IP setting):

詳細情報の設定

Click

and

ネームサーバー

ス

dialup information is required, register such as addresses based on the information assigned by the provider, etc.

: Optional : FOMA D902iS

Enter based on information

given by provider, etc.

to display the IP

setting screens. When

アドレ

Check the settings and click

Click OK

･Performing communication ☛P11

Performing communication

Starting communication set with the FOMA PC configuration software and disconnection are explained here.

Connect FOMA terminal to a PC ☛P3

Double-click the connection icon on the

desktop

･ The icon varies depending on the OS.

完了

･ When there is no connection icon made on

スタート

desktop, start from the

■ Starting from the

Windows XP:

スタート, すべてのプログラム,アク

a Click

セサリ

(Communication), and (Network connection)

b Double-click the connection icon

■ Starting from the

Windows 2000, Me or 98:

スタート, プログラム, アクセサリ, 通

a Click

and

信

(Network and dialup connections)

ダイヤルアップネットワーク

( network) for Windows Me/98)

b Double-click the connection icon

Check each item and click

･ When mopera U / mopera is selected, the entry

ユーザー名

for

スタート

(Accessories), 通信

スタート

ネットワークとダイヤルアップ接続

パスワード

menu.

menu of

ネットワーク接続

menu of

(Dialup

ダイヤル

is not required.

･ If required by the instructions of a subscribed

provider, enter the user name and the password, and then click (Connect) for Windows Me/98) according to the input instruction information.

ダイヤル (接続

･ The connection established screen may be

displayed depending on the OS. Click OK.

(Dial)

■ FOMA terminal screen while communicating

FOMA terminal displays a connecting screen when you execute packet or 64K data communication. The following screens are displayed when a connection has been established:

INFORMATION

● The transmission speed displayed on your PC may differ from actual speed.

● Data transmission is available only with FOMA terminal that was connected when the icon was created.

● When connecting FOMA terminal other than D902iS, installation of the communicatio n conf igurat ion fil e fo r your FOMA terminal is needed.

Disconnecting communication

Just exiting the browser may not disconnect the connection. To ensure disconnection, perform the following operation:

Click in the task tray

･Double-click for Windows Me and 98.

Click 切断(Disconnect)

Optimizing packet communication setup

The method of optimizing the PC packet communication setup for FOMA network by me ans of W-TCP setup and canceling optimization is explained here. The W-TCP setup is a TCP parameter tuning tool fo r optimizing TCP/IP transmission capacity during packet communication in the FOMA network. To enable communication capability of FOMA terminal to maximum extent, this communication setup is required.

For Windows XP

System optimization can be performed for each dialup connection.

Start FOMA PC

Click W-TCP

■ Starting from the task tray: Click

Perform the following:

■ When the system has not been optimized:

a Click

screen

b Select the dialup connection to be

optimized z Click

Optimization of the system settings and dialup settings are performed respectively.

■ When the system has been optimized:

The following screen appears. Make the required settings if changes are to be made.

設定ソフト

設定

最適化を行う

(☛P7) z

on the W-TCP setting

実行

(Execute)

■ Deactivating optimization:

システム設定

a Click

the W-TCP W-TCP (dialup)) screen

The W-TCP setting screen appears.

最適化を解除する

b Click

optimization)

Reboot the PC, following the instruction

shown on the screen

･The settings take effect after rebooting the PC.

Under Windows 2000, Me or 98

Start FOMA PC

Click W-TCP

■ Starting from the task tray: Click

Perform the following:

■ When the system setting has not been

optimized: Click

■ When canceling optimization of the

system setting: Click

Reboot the PC, following the instruction

shown on the screen

･The settings take effect after rebooting the PC.

Setting dialup connections (APNs)

Set the dialup connection (APN) for packet communication. Up to 10 dialup connections (APNs) can be set, which are to be registered under registration numbers (cid) 1 to 10 for management. By default, “mopera.ne.jp” is set for cid1 and “mopera.net” for cid3.

･Before setup, make sure that FOMA terminal and

the PC are properly connected. ☛P3

･For dialup connections (APNs) other than mopera

U / mopera, inquire your provider or network administrator.

Start FOMA PC

Click

The FOMA

接続先

端末設定取得

設定

(APN)設定

(System setting) in

設定 (ダイヤルアップ

(Deactivate

設定ソフト

(☛P7) z

最適化を行う

最適化を解除する

設定ソフト

(☛P7) z

screen appears.



) (Set

Click OK

FOMA terminal is accessed for reading the registered dialup connection (APN) information.

Make the dialup connection (APN) settings

■ Adding dialup connections (APNs): Click

追加

■ Editing or correcting registered dialup

connections (APNs): Select the dialup connection (APN) from the list z Click

集

(Edit)

■ Deleting the regist ered dialup connection

(APN): Select the dialup connection (APN)

削除

from the list z Click

(Delete)

･The dialup connection registered in cid1 and

cid3 cannot be deleted. (Selecting cid3 and

削除

clicking return to “mopera.net”.)

■ Saving settings as file: Click

(File) and

上書き保存

do not actually delete, but

ファイル

名前を付けて保存

(Overwrite)

(Save as...) or

･Save the settings as a file to back up the

dialup connection (APN) settings registered in FOMA terminal or save the dialup connection (APN) settings during editing.

■ Importing settings from file: Click

開く

(Open)

and

･Import settings from a file to edit dialup

connections (APNs) saved on the PC or write to FOMA terminal.

■ Importing the dialup connection (APN)

information from FOMA terminal: Click

イル

and FOMA

settings from FOMA terminal)

Access manually to FOMA terminal to import the registered dialup connection (APN) settings.

■ Writing the dialup connection (APN)

information to FOMA terminal: Click FOMA

端末へ設定を書き込む

FOMA terminal)

The displayed dialup connection (APN) settings are written to FOMA terminal.

端末から設定を取得

(Write settings to

編

ファイル

ファ

(Import

■ Creating dialup connections:

a Select an added or edited dialup

connection (APN) z Click

プ作成

(Create dialup connection)

The FOMA to FOMA terminal) screen appears.

b Click

When the dialup connection (APN) information have been writ ten t o FOMA terminal,the

プの作成

packet communication) screen appears.

c Enter any connection name z Click

端末設定書き込み

はい

z Click OK

パケット通信用ダイヤルアッ

(Create dialup connection for

カウント・パスワードの設定

account and password)

d Enter the user name in

the password in

パスワード

ダイヤルアッ

(Write setting

(Set

ユーザー名

z Click OK

･Not required for mopera U / mopera. ･For Windows XP or 2000, select the

allowable user. If you select

ユーザー

, all users that are allowed to logon to Windows can access the connection.

･Some providers, etc. may request you to

enter IP and DNS information settings. Should this be the case, click

設定

in the

プの作成

information and click OK.

e Click OK z Click OK f Click FOMA

A confirmation screen appears asking whether to overwrite.

g Click

パケット通信用ダイヤルアッ

screen, register the required

端末へ設定を書き込む

はい

z Click OK

INFORMATION

● Since the dialup connection (APN) setting is information saved in FOMA terminal, re-register the APN when connecting another FOMA terminal (terminal replaced by repair, etc.).

● To continue to use the dialup connection (APN) saved in the PC, save the registration number (cid) of the same APN to FOMA terminal.

● When FOMA terminal is detected as number other than COM1 to 9 by checking the communication configuration file, APN information may not be obtained or written during an APN setting. In that case, set the information using “HyperTerminal” that comes with Windows. ☛P15

ア

and

すべての

詳細情報の

Uninstalling the FOMA PC configuration software

Before operation, read “Before installation/ uninstallation” ☛P3

Uninstall preparations

Right-click in the task tr ay, an d cl ick (Do not reside) to cancel the resident of W-TCP setup.

常駐させない

Uninstalling

Example

For Windows XP

Click

スタート, コントロールパネル

the

プログラムの追加と削除

■ For Windows 2000, Me, 98:

a Click

スタート, 設定

ネル

b Double-click the

と削除

icon

and

コントロールパ

アプリケーションの追加

Select NTT DoCoMo FOMA PC

ト

(NTT DoCoMo FOMA PC configuration

software) z Click

･ For Windows Me or 98, click

変更と削除

追加と削除

and

icon

設定ソフ

Check that you have selected the correct program to delete and click

The uninstallation of the FOMA PC configuratio n software starts.

■ Canceling W-TCP optimization:

A confirmation screen appears when W-TCP has been optimized.

･Usually, click

optimization.

はい

and deactivate the

･Select whether to reboot immediately and

完了

click reboot the PC.

when Windows prompts you to

･Canceling of W-TCP optimization is

performed after the PC is rebooted.

Click OK

Communication

Communicating without using the FOMA PC configuration software

The method of dialup network setup for packet communication/64K data communication without using the FOMA PC configuration software is explained.

Setting operation procedures

Install the communication configuration file ☛P4 Connect a PC to FOMA terminal ☛P3

Set the dialup connection (APN) (This setting is not required for 64K data communication, and for packet communication via mopera U / mopera.)

Set to show/hide caller ID ☛P17 (Set as required.)

Other settings (AT commands) ☛P25

(Set as required.)

Dialup network setup

P17

P19 P22

P23

Settings

TCP/IP

P18 P21 P22

P23

Windows XP Windows 2000 Windows Me Windows 98

• For details on settings, inquire your provider or network administrator.

Dialup connection

Connect ☛P23 (Disconnect ☛P24)

Setting the dialup connection (APN) for packet communication

Communication software to input AT commands is required for making settings. The method of setting using “HyperTerminal” that comes with Windows is explained here.

Default

cid1：mopera.ne.jp cid3：mopera.net cid2, 4 to 10：not recorded

Example

1 2

For Windows XP

Connect FOMA terminal to a PC ☛P3 Click

スタート, すべてのプログラム, アクセサリミナル

and 通信 z Click

ハイパーター

(HyperTerminal). (And double-click

the Hypertrm icon under Windows 98.)

･For other than Windows XP,

displayed for

すべてのプログラム

プログラム

Enter any connection name in 名前 z

Click OK

Enter a fictional phone number (such as 0) for

電話番号方法

･ Since

Click

screen appears Enter the dialup connection (APN) z Press

･ Enter in the format “AT

<cid> : Enter any number between 2, 4 to 10. “PPP” : Enter “PPP”. “APN”: Enter the dialup connection (APN) in

, select FOMA D902iS from

(Connection procedure) z Click OK

市外局番

(Area code) does not effect the dialup connection (APN) setting, it is not necessary to change.

キャンセル

when the connection

CGDCONT =<cid>,

“PPP”, “APN””.

quotation marks.

接続

If OK appears, the dialup connection (APN) has now been set.

■ Resetting the dialup connection (APN)

settings:

AT + CGDCONT

Reset all cids.

･The settings are restored to the default

settings for <cid> = 1 and 3, and the settings for <cid> = 2, 4 to 10 are cleared.

AT + CGDCONT=<cid>

Reset the specified cid

■ Checking the dialup connection (APN)

settings:

AT + CGDCONT?

･ For details ☛P30

■ When nothing is displayed even if AT

command is entered: ATE1

･ For details ☛P28

Check that OK is displayed and click

ファイル了

･After

･“XXX”

Dialup connection (APN) and registration number (cid)

The dialup connection (APN) for packet communication can be set for registration numbers between cid1 to 10 in FOMA terminal. By default, “mopera.ne.jp” is set for cid1 and “mopera.net” for cid3. For connecting to other providers or corporate LANs, register the dialup connection (APN) for cid2, 4 to 10.

and

(End HyperTerminal)

現在、接続されています。切断してもよ

ろしいですか？

appears, click

と名前付けされた接続を保存しますか

(Save the connection named “XXX”?) appears.

いいえ

Click

ハイパーターミナルの終

(Connecting now. Disconnect?)

はい

･ For the dialup connection (APN), inquire your

provider or network administrator.

･ The dialup connection settings can be consider ed

as phonebook registration for packet communication. The comparison between dialup connection settings and the FOMA terminal phonebook entries is as follows:

Dialup connection

settings

Registration number (cid)

APN Party’s phone number

･ The registered cid become the connection

numbers of dialup connection setting.

Setting to show/hide caller ID

Take care when disclosing your caller ID since it is important information.

･ Settings must be “show” for using mopera U /

mopera.

Default not set

Example

For Windows XP

Perform Steps 1 to 5 of “Setting the dialup connection (APN) for packet

FOMA terminal phonebook

entries

Registration number (Phonebook No.)

communication” ☛P15 Set to show (186)/hide (184) caller ID

during packet communication

Enter in the format “AT ＊ DGPIR=<n>”.

AT ＊ DGPIR=1

When packet communication connection is being established, “184” is added to connect to the dialup connection (APN).

AT ＊ DGPIR=2

When packet communication connection is being established, “186” is added to connect to the dialup connection (APN).

■ When nothing is displayed even if AT

command is entered: ATE1

･ For details ☛P28

Check that OK is displayed and click

イル

and

ハイパーターミナルの終了

･ After

現在、接続されています。切断してもよ

ろしいですか？

･ “XXX”

appears. Click

■ Setting to show/hide caller ID by dialup

network settings

appears, click

と名前付けされた接続を保存しますか

いいえ

はい

ファ

The dialup network settings can also be used to append “186 (show)” or “184 (hide)” to the dialup connection number. If “186” (show) or “184” (hide) is set by both the AT ＊ DGPIR command and dialup network settings, the show/hide caller ID setting is as follows:

Setting made by

＊

DGPIR

command

Dialup network setting (<cid>=3)

＊ 99 ＊＊＊3#

184 ＊ 99＊＊＊ 3# 186 ＊ 99＊＊＊ 3#

･ To reset the show/hide setting made by the AT ＊

DGPIR command to the default (not set), enter “AT ＊ DGPIR=0”.

Setting for Windows XP

Setting the dialup connection

Click

スタート, すべてのプログラム, ア

クセサリ

The

ネットワーク接続

Click

新しい接続を作成する

connection) in

Not set Hide Show

Caller ID

is sent.

Caller ID is not sent.

Caller ID is sent.

, 通信 and

ネットワーク接続

screen appears.

ネットワークタスク

Caller ID

is not

sent.

(Network task)

The

新しい接続ウィザード

wizard) screen appears.

Click

A screen for selecting the type of network connection appears.

Select

インターネットに接続する

(Connect to Internet) z Click

The setup screen appears.

Select

接続を手動でセットアップする

(Set up connection manually) z Click

The Internet connection screen appears.

Select

ダイヤルアップモデムを使用して

接続する

z Click

The device selection screen appears.

･If there is only one modem installed, the device

selection screen is not displayed. Go to Step 8.

(Use dialup modem to connect)

(New connection

Caller ID

is sent.

(Create new

Select

モデムー

(Modem: FOMA D902iS (COMx)) z Click

FOMA D902iS (COMx)*1

へ

･ Check that only

(COMx)*

*1 “x” of COMx varies by PC to be used.

Enter any connection name in ISP名(ISP

name) z Click

Enter the number of the dialup connection

(one-byte) in

■ For packet communication:

Enter “ ＊99 ＊＊＊<cid>#”.

･For <cid>, enter the cid number registered

in “Setting the dialup connection (APN) for packet communication” ☛P15. “＊99＊＊＊ 3#” for mopera U and “＊99＊＊＊1#” for mopera.

■ For 64K data communication:

Enter the dialup connection phone number.

･“＊8701” for mopera U and “ ＊9601” for

mopera.

モデム−

is selected.

電話番号

FOMA D902iS

z Click

Enter the user name in

次

password in

の確認入力

z Set each items as shown below z Click

･When the access point is mopera U / mopera,

Click

Check the settings and click

･Check the settings without connecting to the

Setting TCP/IP protocol

Select the created dialup connection icon z

Click

パスワード

(Check and enter password)

the entry for

ワードの確認入力

items as shown and click

ユーザー名, パスワード

is not required. Set each

完了

Internet immediately.

ファイル

and

プロパティ

ユーザー名

and

パスワード

キャンセル

(Properties)

, the

and

パス

Check the setting of each item in the

(General) tab

･ When multiple modems are installed to the PC,

モデム

ー

select

方法

･ Check that only

(COMx)* *1 “x” of COMx varies by PC to be used.

･ Uncheck ( )

information).

FOMA D902iS (COMx)*1 in

モデム−

is selected.

FOMA D902iS

ダイヤル情報を使う

全般

接続

(Use dial

Click

4 5

Setting for Windows 2000

Setting the dialup connection

設定

Uncheck ( ) all items and click OK

The dialup connection properties screen reappears.

Click OK

Click

スタート, プログラム, アクセサリ

通信

and

ネットワークとダイヤルアッ

プ接続

The

ネットワークとダイヤルアップ接続

appears.

screen

Click the

Check the setting of each item

･ Set PPP: Windows 95/98/NT4/2000, Internet as

･ Select only

ネットワーク

呼び出すダイヤルアップサーバーの種類

of dialup server to call).

インターネットプロトコル

IP) (Internet protocol (TCP/IP)) in

の項目を使用します

connection). Since QoS (QoS packet scheduler) settings can not be changed, leave it as it is.

(Network) tab z

この接続は次

(Use these items for this

パケットスケジューラ

(Type

(TCP/

Double-click the

new connection)

The

所在地情報

appears.

･This screen appears for the first time you

double-click the the second time, go to Step 5.

Enter the number in

z Click OK

The

電話とモデムのオプション

modem options) screen appears.

Click OK

The

ネットワークの接続ウィザード

connection wizard) screen appears.

Click

A screen for selecting the type of network connection appears.

Select

インターネットにダイヤルアップ

接続する

Internet) z Click

The start screen of

ド

(Internet connection wizard) appears.

新しい接続の作成



icon

(Location information) screen

新しい接続の作成

市外局番

(Phone and

(Use dialup connection to

インターネット接続ウィザー

(Create

icon. From

(Area code)

(Network

Select

インターネット接続を手動で設定するか、またはローカルエリアネットワーク

(LAN)

を使って接続します

the Internet connection manually or connect using local area network (LAN)) z Click

The Internet connection setting selection screen appears.

Select

電話回線とモデムを使ってインターネットに接続します

Internet using phone line and modem) z Click

The modem selection screen appears.

･ This screen is not displayed if multiple modems

are not installed. Go to Step 10.

Check that

インターネットへの接続に使

うモデムを選択する

for connection to Internet) is set to FOMA D902iS and click

The Internet account connection information screen appears.

･ If FOMA D902iS is not set, set FOMA D902iS.

Enter the number of dialup connection (one-byte) in (Detailed settings)

･ Uncheck ( )

(Use area code and dial information).

■ For packet communication:

Enter “＊99＊＊＊<cid>#”.

･For <cid>, enter the cid number registered in

“Setting the dialup connection (APN) for packet communication” ☛P15. “＊99 ＊＊＊ 3#” for mopera U and “＊99 ＊＊＊1#” for mopera.

■ For 64K data communication:

Enter the dialup connection phone number.

･“＊8701” for mopera U and “＊ 9601” for

mopera.

電話番号

市外局番とダイヤル情報を使う

(Connect to

(Select modem to use

z Click

詳細設定

(Set

Set each item in the 接続 tab as shown

below

Click the

each item as shown below

Click OK

The Internet account connection information screen reappears.

Click

The Internet account logon information screen appears.

Enter the user name in

password in

･When the dialup connection is mopera U /

アドレス

(Address) tab z Set

ユーザー名

パスワード

mopera, the entry for is not required. When a confirmation screen for no entry appears, click

z Click

ユーザー名

はい

and the

パスワード

Enter any connection name in

Click

Select

いいえ

Click

Setting TCP/IP protocol

完了

The

ネットワークとダイヤルアップ接続

reappears.

Select the created dialup connection icon

z Click

ファイル

and

接続名

プロパティ

screen

Check the setting of each item in the

tab

･If multiple modems are installed in the PC,

モデム

ー

select

の方法

When the modem is changed, all items in

is initialized. Re-enter the dialup

番号

connection phone number in that case.

･Check that only

(COMx)* *1 “x” of COMx varies by PC to be used.

･Uncheck ( )

Click the

setting of each item

･Set PPP: Windows 95/98/NT4/2000, Internet as

呼び出すダイヤルアップサーバーの種類

･Select only

IP) for component.

FOMA D902iS (COMx)*1 in

(Connection procedure).

モデム−

is selected.

ネットワーク

インターネットプロトコル

FOMA D902iS

ダイヤル情報を使う

tab z Check the

全般

接続

電話

(TCP/

Click

設定

Uncheck all items ( ) and click OK

The dialup connection properties screen reappears.

Click OK

Setting for Windows Me

Setting the dialup connection

The setting procedures are the same as for

･

Windows 98.

Click

3 4

スタート, プログラム, アクセサリ

通信

and

ダイヤルアップネットワーク

The

ダイヤルアップネットワークへようこそ

(Welcome to dialup network) screen appears.

･ This screen appears when

ネットワーク

the second time, go to Step 3.

Click

The

ダイヤルアップネットワーク

appears.

Double-click the connection) icon

Enter any connection name in Click

･ Check that FOMA D902iS is set for

. If it is not set, set FOMA D902iS.

択

is selected for the first time. From

ダイヤルアップ

新しい接続

screen

(New

接続名

モデムの選

■ For 64K data communication:

Enter the dialup connection phone number.

･ “＊8701” for mopera U and “＊ 9601” for

mopera.

･

市外局番

Check the name of the dialup connection

z Click

Setting TCP/IP protocol

Select the created dialup connection icon

z Click

Check the setting of each item in the 全般

tab

･Uncheck ( )

ティを使う

･Check that FOMA D902iS is set for

is not set, set FOMA D902iS.

does not need to be entered.

完了

ファイル

and

プロパティ

市外局番とダイヤルのプロパ

(Use area code and dial properties).

接続方法

. If it

Enter the dialup connection number (one-

byte) z Click

■ For packet communication:

Enter “＊99＊＊＊<cid>#”.

･For <cid>, enter the cid number registered in

“Setting the dialup connection (APN) for packet communication” ☛P15. “＊99 ＊＊＊ 3#” for mopera U and “＊99 ＊＊＊1#” for mopera.

Click the

setting of each item

･ Set

･ Uncheck ( ) all

･ Select only TCP/IP for

ネットワーク

ダイヤルアップサーバーの種類

server type) to PPP: 2000/NT、 Windows Me (PPP: Internet, Windows

2000/NT, Windows Me).

options).

クプロトコル

(Available protocol).

tab z Check the

インターネット

詳細オプション

使用できるネットワー

(Dialup 、 Windows

(Detailed

Setting for Windows 98

Setting the dialup connection

The setting procedures are the same as for Windows Me. ☛P22

Setting TCP/IP protocol

Perform steps 1 to 2 of “Setting TCP/IP

protocol” of “Setting for Windows Me” ☛P22

Click the

Enter the user name in password in

･ When the dialup connection is mopera U /

セキュリティ

パスワード

mopera, the entry for is not required.

(Security) tab z

ユーザー名

and click OK

ユーザー名

パスワード

, the

Click the

tab z Check the setting of each item

･

･Uncheck ( ) all ･Select only TCP/IP for

Click OK

Connecting through dial-up

The method of dialup connection for packet communication/64K data communication is explaine d.

サーバーの種類

Set

ダイヤルアップサーバーの種類

インターネット

(PPP: Internet, Windows NT Server, Windows 98).

プロトコル

、

Windows NT Server、

詳細オプション

(Server type)

使用できるネットワーク

PPP:

Windows 98

Example

1 2

For Windows XP

Connect FOMA terminal to a PC ☛P3 Click

スタート, すべてのプログラム, ア

クセサリ

The

･Under the Windows 2000, Me or 98, click

, 通信 and

ネットワーク接続

タート

プログラム, アクセサリ, 通信トワークとダイヤルアップ接続プネットワーク

screen appears.

for Windows Me/98).

ネットワーク接続

ス

and

(

ダイヤルアッ

ネッ

Double-click the dialup connection icon

Check each item and click

･ Under the Windows Me and 98, check each

item and click

･ The number of dialup connection set for the

dialup network is shown in

号

･ When the dialup connection is mopera U /

mopera, the entry for is not required.

接続

ユーザー名

ダイヤル

電話番

パスワード

Disconnecting communication

Just exiting the browser may not disconnect the connection. To ensure disconnection, perform the following operation:

Click in the task tray

･Double-click for Windows Me and 98.

Click

切断

AT command

AT commands are commands for setting FOMA terminal functions using a P C . FOMA terminals comply with AT commands and support some extended commands and proprietary AT commands.

About the AT command

■ AT command input format

“AT” must be entered before each AT command. Commands must be entered in one-byte alphanumeric characters. An input example is as follows:

ATD ＊ 99 ＊＊＊ 3#

Command AT commands and their parameters (numbers or

symbols) must be entered on a single line. Enter all the characters from the first character to the character just before in a single line. Up to 160 characters (including “AT”) can be entered in each line.

■ AT command input mode

To operate FOMA terminal using AT commands, the PC must be in the terminal mode. Terminal mode is a mode that lets the PC operate as a single communication terminal. Characters entered from the keyboard are sent to the device or line connected to the communication port.

Parameter

･ Offline mode

FOMA terminal in standby status. Usually, FOMA terminal must be in this status to use AT commands to control it.

･ Onlin e data mode

FOMA terminal is in the communication mode. If you enter AT commands when FOMA terminal is performing communication, the received characters are sent directly to the communication receiver and may cause the receiver’s modem to malfunction. Do not enter AT commands while FOMA terminal is performing communication.

･ Online command mode

AT commands allow you to operate FOMA terminal even when FOMA terminal is in the communication mode. These opera tions make it possible to execute AT commands without interfering with the connection to the communication receiver, and normal communication can be continued after the commands have finished executing.

Press Enter key.

Switching between the online data mode and online command mode

To switch FOMA terminal from the online data mode to online command mode, you can use either of the following procedures:

･ Enter th e “ +++” command or the code set in the

“S2” register.

･ Turn the RS-232C*

“AT&D1”. To switch from the online command mode to online data mode, enter “ATO ”.

*1 The USB interface emulates an RS-232C signal line,

so RS-232C signal control using communication applications is possible.

ER signal off when set in

AT command list

･ When AT commands are input, entering “

￥

” may cause “\” to appear depending on the font settings

for the PC or communication software in use.

･ If the battery pack is removed from FOMA terminal before the terminal power is turned off, the setting

values may not be recorded.

･ AT commands that can be used via the FOMA D902iS Modem Port are described in this list.

*1 :Returns the setting to default with the AT & F command. *2 :Stores the command setting into FOMA terminal with the AT&W command and restores it with the ATZ command. None : Indicates the AT command does not include any display command or test command. [ ] :Indicates the parameter can be omitted.

Command Description & Parameter

AT%V Shows the version of your FOMA terminal in the format of “Verx.xx”.

AT&C [n] Selects the operational conditions of the circuit CD signal outgoing to DTE.

*1, *2 ex. Enter AT&C1 Display None Test None AT&D [n] Determines an action to be taken when t he circ u it ER si gn al comi ng fr om D TE changes from on to off

*1, *2 ex. Enter AT&D1 Display None Test None AT&E [n] Selects type of speed display used when connection is made.

*1, *2 ex. Enter AT&E1 Display None Test None

AT&F [0] Resets all FOMA terminal state to the default. When executed while receiving a call, it resets FOMA

AT&S [n] Determines the control of the DR signal FOMA terminal outputs.

*1, *2 ex. Enter AT&S0 Display None Test None

AT&W [0] Writes the current settings in to FOM A ter mina l .

AT ＊ DANTE Shows the signal strength (reception level) in the format of “＊DANTE:m”.

AT ＊ DGANSM=n Specifies whether to reject or accept an incoming packet call.

AT ＊ DGAPL=n [,cid] Specifies dialup connections (APNs) to accept incoming packet calls from them. For an APN, use the

AT ＊ DGARL=n [,cid] Specifies dialup connections (APNs) to reject incoming packet calls from them. For an APN, use the

ex. Enter AT%V Display None Test None

n=0: The circuit CD signal is always on. (when parameter omitted) n=1: The circuit CD signal varies depending on the other modem. (default)

in the online data mode. n=0: Ignores the ER signal condition (always on). (when parameter omitted) n=1: Switches the mode to the online command mode when the ER signal changes from on to off. n=2: Disconnects the circuit and switches the mode to the offline mode when the ER signal changes from on to off. (default)

This command is effective only when the ATX command is other than “n=0”. n=0: Displays communication speed of wireless zone. n=1: Displays communication speed between PC and FOMA terminal. (default)

terminal state to the default without affecting the call. When executed during communication, the terminal state returns to default after it disconnects (display “NO CARRIER”) the communication.

ex. Enter AT&F0 Display None Test None

n=0: Always on. (default and when parameter omitted) n=1: The DR signal turns on when the circuit is connected.

ex. Enter AT&W0 Display None Test None

m=0: Outside the service area m=1 to 3: Number of antennas displayed on FOMA term inal (m =1 : 0 or 1)

ex. Enter AT ＊ DANTE Display AT ＊ DANTE? Test AT ＊ DANTE=?

n=0: Sets both the incoming call rejection and the incoming call acceptance off. (default) n=1: Sets the incoming call rejection on. n=2: Sets the incoming call acceptance on.

ex. Enter AT ＊ DGANSM=0 Display AT ＊ DGANSM? Test AT ＊ DGANSM=?

cid parameter defined with “+CGDCONT”. n=0: Adds the APN defined with the cid parameter to the call acceptance list. n=1: Deletes the APN defined with the cid parameter from the call acceptance list. When you omit the cid parameter, all cids will be added or deleted.

ex. Enter AT ＊ DGAPL=0,1 Display AT＊ DGAPL? Test AT ＊DGAPL=?

cid parameter defined with “+CGDCONT”. n=0: Adds the APN defined with the cid parameter to the call rejection list. n=1: Deletes the APN defined with the cid parameter from the call rejection list. When you omit the cid parameter, all cids will be added or deleted.

ex. Enter AT ＊ DGARL=0,1 Display AT ＊ DGARL? Test AT ＊ DGARL=?

Command Description & Parameter

AT ＊ DGPIR=n Specifies whether to notify the caller ID for packet communication. This specification is effective both

AT ＊ DRPW Shows the level of power receptio n in the for mat of “＊DRPW:m”, where the valu e of m ra nges from 0

+++ Changes FOMA terminal mode from the online data to the online command. The duration of escape

AT+CEER Shows a disconnection reason of the previous communication. ☛P30

AT+CGDCONT Specifies the APN for packet communication. ☛P30 AT+CGEQMIN Specifies the criteria for judging whether to approve the QoS (Quality of Service) level provisioned by

AT+CGEQREQ Specifies the QoS level requested to the network when transmission is performed during packet

AT+CGMR Shows the version of your FOMA terminal with a 16-digit numb er.

AT+CGREG= [n] Determines whether to notify the network registration state. Either “inside the service area” or “outside

*1, *2 ex. Enter AT+CGREG=1 Display AT+CGREG? Test AT+CGREG=?

AT+CGSN Shows the manufacturer’s serial number of FOMA terminal.

AT+CLIP= [n] Shows the caller ID of an incoming 64K data communication on the PC’s screen.

*1, *2 ex. Enter AT+CLIP=0 Display AT+CLIP? Test AT+CLIP=?

AT+CLIR= [n] Specifies whether to show your caller ID to the other party when you originate a 64K data

AT+CMEE= [n] Specifies the error report format of FOMA terminal. ☛P30

*1, *2 ex. Enter AT+CMEE=0 Display AT+CMEE? Test AT+CMEE=?

AT+CNUM

AT+CR= [n] Specifies whether to display the communication type (packet communication or 64K data

*1, *2 ex. Enter AT+CR=0 Display AT+CR? Test AT+CR=?

for outgoing and incoming calls. n=0: The APN is used as it is when a packet communication is established. (default) n=1: Adds “184” to the APN when a packet communication is established. n=2: Adds “186” to the APN when a packet communication is established.

ex. Enter AT ＊ DGPIR=0 Display AT ＊ DGPIR? Test AT ＊ DGPIR=?

to 75.

ex. Enter AT ＊ DRPW Display None Test AT ＊DRPW=?

guard is fixed to 1 sec.

ex. Enter +++ Display None Test None

ex. Enter AT+CEER Display None Test AT+CEER=?

the network when the packet communication is established. ☛P30

communication. ☛P31

ex. Enter AT+CGMR Display None Test AT+CGMR=?

the service area” is notified. n=0: Not notified. (default and when parameter omitted) n=1: Notified in the format of “+CGREG:n,stat”.

stat=0: Outside the service area stat=1: Inside the service area (home) stat=4: Unk nown stat=5: Inside the service area. (visit or)

ex. Enter AT+CGSN Display None Test AT+CGSN=?

n=0: Does not show the information. (default and when parameter omitted) n=1: Shows the information. If you enter “AT+CLIP?”, it shows “+CLIP:n,m”.

m=0: The network setting that does not show caller ID to the other party when originating a call. m=1: The network setting that shows caller ID to the other party when originating a call. m=2: Unknown

communication. n=0: In accordance with the service agreement. (when parameter omitted) n=1: Not notified. n=2: Notifies the caller ID. (default) If you enter “AT+CLIR?”, it shows “+CLIR:n,m”.

m=0: CLIR is not activated. (caller ID always notified) m=1: CLIR is activated. (caller ID always not

notified) m=2: Unknown m=3: CLIR temporary mode (default for “not notified”) m=4: CLIR temporary mode. (default for “notified”)

ex. Enter AT+CLIR=0 Display AT+CLIR? Test AT+CLIR=?

n=0: Shows “ERROR”. (default and when parameter omitted) n=1: Shows in the format of “+CME ERROR:xxxx”. (xxxx=numbers) n=2: Shows in the format of “+CME ERROR:xxxx”. (xxxx=characters)

Shows the Own Number data of FOMA terminal in the format of “+CNUM:, “number”,type”. number: Phone number

type=129: Does not show “+81”. type=145: Shows “+81”.

ex. Enter AT+CNUM Display None Test AT+CNUM=?

communication) before CONNECT is displayed, during line connection. n=0: Does not show the information. (default and when parameter omitted) n=1: Shows the information in the format of “+CR:serv”.

serv=SYNC: 64K data communication serv=GPRS: Packet communication

Command Description & Parameter

AT+CRC= [n] Specifies whether to use result codes of “+CRING:type” for incoming calls.

*1, *2 ex. Enter AT+CRC=0 Display AT+CRC? Test AT+CRC=? AT+CREG= [n] Specifies whether to show the “inside/outside the service area” information.

*1, *2 ex. Enter AT+CREG=0 Display AT+CREG? Test AT+CREG=?

AT+GMI Shows the manufacturer’s name of FOMA terminal.

AT+GMM Shows FOMA terminal name.

AT+GMR Shows the version of FOMA terminal.

AT+IFC= [n,[m]] Specifies the local flow control between the PC and FOMA terminal.

*1, *2 ex. Enter AT+IFC=2,2 Display AT+IFC? Test AT+IFC=? AT+WS46= [22] Specifies the radio network FOMA terminal uses to originate a call. *1, *2 ex. Enter AT+WS46=22 Display AT+WS46? Test AT+WS46=?

ATA Specifies how to handle incoming packet or 64K data communications. For incoming packet

A/ Reexecutes the previous command.

ATD Originates a packet or 64K data communication.

ATE [n] Echoes back the characters sent from the PC.

*1, *2 ex. Enter ATE0 Display None Test None

ATH Disconnects communication.

ATI [n] Shows the identification code.

ATO Switched the mode from the online command to the online data.

ATQ [n] Specifies whether to show the result code on the PC.

*1, *2 ex. Enter ATQ0 Display None Test None

n=0: Does not use the result code of “+CRING:type”. (default and when parameter omitted) n=1: Uses the result code of “CRING:type”. The example of codes are as follows:

Packet communication … +CRING:GPRS “PPP”… “mopera.net” 64K data communication… +CRING:SYNC

n=0: Does not show the information. (default and when parameter omitted) n=1: Shows the information. If you enter “AT+CREG?”, it shows the information in the format of “+CREG:n,stat”.

stat=0: Outside the service area stat=1: Inside the service area (home) stat=4: Unknown stat=5: Inside the service area (visitor)

ex. Enter AT+GMI Display None Test AT+GMI=?

ex. Enter AT+GMM Display None Test AT+GMM=?

ex. Enter AT+GMR Display None Test AT+GMR=?

n is for setting the DCE-by-DTE control.

n=0: Does not use the flow control. n=1: Uses XON/XOFF flow control. n=2: Uses RS/CS (RTS/CTS) flow control. (default)

m is for setting the DTE-by-DCE control. If you omit this parameter, the same value as DCE-by-DTE is assumed.

m=0: Does not use the flow control. m=1: Uses XON/XOFF flow control. m=2: Uses RS/CS (RTS/CTS) flow control. (default)

If you omit both parameters, “AT+IFC=2, 2” is assumed.

communications, you can specify the following: ATA184: Receives an incoming call without the caller ID displayed ATA186: Receives an incoming call with the caller ID displayed

ex. Enter ATA Display None Test None

ex. Enter A/ Display None Test None

・Packet communication: Enter in the format of “ATD＊99 ＊＊＊ cid#”. If you omit cid parameter,

“cid=1” is assumed. When you enter it in the format starting with “A TD184＊99”, 184 (hide caller ID) is attached t o the call outgoing to the APN specified wit h cid pa ramete r (186 (show call er ID) i s treate d in the same man ner).

・64K data communication: Enter it in the format of “ATD phone-number”. ・Redialing: Enter in the format of “ATDL” or “ATDN”.

ex. Enter ATD phone-number Display None Test None

n=0: Gives no echo back. (when parameter omitted) n=1: Gives echo back. (default)

ex. Enter ATH Display None Test None

n=0:Shows “NTT DoCoMo”. (when parameter omitted) n=1:Shows model name of FOMA terminal. n=2:Shows the version of FOMA terminal.

ex. Enter ATI0 Display None Test None

ex. Enter ATO Display None Test None

n=0: Shows the result code. (default and when parameter omitted) n=1: Does not show the result code.

Command Description & Parameter

ATV [n] Specifies the displaying procedure.

*1, *2 ex. Enter ATV1 Display None Test None ATX [n] Specifies whether to detect busy tone and d ial ton e, and whethe r t o display th e com municat ion s pee d.

*1, *2 ex. Enter ATX1 Display None Test None

ATZ Resets FOMA terminal settings to those stored in the non-volatile memory with the AT&W command.

ATS0= [n] Specifies the number of ringing signals (RING) which triggers automatic call acceptance on FOMA

*1, *2 ex. Enter ATS0=0 Display ATS0? Test None ATS2= [n] Specifies an escape character.

*1 ex. Enter ATS2=43 Display ATS2? Test None ATS3= [13] Specifies a carriage return (CR) character that indicates the end of AT command’s character string

*1 ex. Enter ATS3=13 Display ATS3? Test None ATS4= [10] Specifies the Line Feed (LF) character (the setting is not changeable). It follows the CR character

*1 ex. Enter ATS4=10 Display ATS4? Test None ATS5= [8] Specifies a backspace (BS) character that deletes the last character in the input buffer while you are

*1 ex. Enter ATS5=8 Display ATS5? Test None ATS6= [n] Specifies the pause period before dialing. This command sets the register but no action will occur.

*1 ex. Enter ATS6=5 Display ATS6? Test None ATS8= [n] Specifies the comma dialing function (pause time). This command sets the register but the pause time

*1 ex. Enter ATS8=3 Display ATS8? Test None ATS10= [n] Specifies the permissible delay time before automatic disconnection. This command sets the register

*1, *2 ex. Enter ATS10=1 Display ATS10? Test None ATS30= [n] Specifies the time elapsed after the last data transmission to activate automatic disconnection. This

*1 ex. Enter ATS30=0 Display ATS30? Test None ATS103= [n] Specifies a mark to be used to delimit a destination sub-address if attached. This command is

*1 ex. Enter ATS103=0 Display ATS103? Test None ATS104= [n] Specifies a mark to be used to delimit a caller sub-address if attached. This command is effective for

*1 ex. Enter ATS104=0 Display ATS104? Test None

AT￥S Shows th e contents of command settings and the S register.

AT￥V [n] Selects whether to use the extended result code for connection.

*1, *2 ex. Enter AT￥V0 Display None Test None

n=0: Shows the result with numeric codes. (when parameter omitted) n=1: Shows the result with text messages. (default)

n=0: Busy tone not detected, dial tone not detected, communication speed not displayed. (when

parameter omitted) n=1: Busy tone not detected, dial tone not detected, communication speed displayed. n=2: Busy tone not detected, dial tone detected, communication speed displayed. n=3: Busy tone detected, dial tone not detected, communication speed displayed. n=4: Busy tone detected, dial tone detected, communication speed displayed. (default)

If you enter this command during receiving a packet or 64K data communication, the settings are reset without affecting the call reception. If you enter it during communication, it disconnects the communication first and resets the settings.

ex. Enter ATZ Display None Test None

terminal. n=0: Does not accept calls automatically. (default and when parameter omitted) n=1 to 255

n=0 to 127 (43: Default 0: When parameter omitted 127: To disable the escape processing)

(the setting is not changeable). It is attached to the end of the echoed back command string and the result code.

when the result code is displayed with text.

entering an AT command (the setting is not changeable).

n=2 to 10: 2 to 10 seconds. (5: Default and when parameter omitted)

is fixed to 3 seconds. n=0 to 255: 0 to 255 seconds. (3: default 0: When parameter is omitted)

but no action will occur. n=1 to 255: in 1/10 seconds. (1: default and when parameter omitted)

command is effective for 64K data communication. n=1 to 255: 1 to 255 minutes. n=0: Does not disconnect. (default and when parameter omitted)

effective for 64K data communication. n=0: ＊ ( when parameter omitted) n=1: / (default) n=2:

64K data communication. n=0: # (when parameter omitted) n=1: % (default) n=2: &

ex. Enter AT￥S Display None Test None

This command takes effect when the ATX command parameter is “n=1 to 4”. n=0: Does not use the extended result code. (default and when parameter omitted) n=1: Uses the extended result code.

￥

Disconnection reason list

■ Packet communication

Value Reason

27 APN is not present or is incorrect. 30 Disconnected by network. 33 Terminal does not subscribe to packet

communication.

36 Normal disconnection.

■ 64K data communication

Value Reason

1 Specified number does not exist. 16 Normal disconnection. 17 Communication is impossible because remote

device is busy.

18 You made a call but did not receive a response

within the specified time.

19 A call was made to the other party, but no

response. 21 The remote device rejected incoming calls. 63 The service and option of the network are not valid. 65 Unavailable processing speed was specified. 88 You made a call to a terminal or received a call

from a terminal with different terminal properties.

Error messages list

No. Text display Reason

10 SIM not

inserted 15 SIM

wrong 16 incorrect

password

100 unknown Unknown error

No UIM (FOMA card) is set.

Other than UIM (IC card equivalent to UIM) is inserted.

Incorrect password

Supplement to AT command

■ Command name: AT+CGDCONT= [parameter]

Sets the dialup connection (APN) for packet communication.

Format

AT+CGDCONT=[<cid>[, “PPP” [, “<APN>”]]]

Parameter description

<cid>: 1 to 10

“mopera.ne.jp” (APN) is registered in cid 1, and “mopera.net” in cid 3.

<APN>: Optional

Example of execution

The command used to register an APN named “abc” (when <cid>=2). AT+CGDCONT=2, “PPP”, “abc”

Operation performed when parameter is omitted

AT+CGDCONT

= Clears all <cid> settings. However, entry for “<cid>=1” and “<cid>=3” is restored to the default setting.

AT+CGDCONT=<cid>

Clears the specified <cid> settings. However, entry for “<cid>=1” and “<cid>=3” is restored to the default setting.

AT+CGDCONT=？

Displays a list of assignable values.

AT+CGDCONT？

Displays the current setting values.

■ Command name: AT+CGEQMIN= [parameter]

Registers the criteria for judging whether to approve QoS provisioned by the network when PPP packet communication is established.

Format

AT+CGEQMIN= [<cid>[,,<Maximum bitrate UL>[,<Maximum bitrate DL>]]]

Parameter description

<cid>：1 to 10

“mopera.ne.jp” (APN) is registered in cid 1 and

“mopera.net” in cid 3. <Maximum bitrate UL>: None or 64 <Maximum bitrate DL>: None or 384

For “Maximum bitrate UL” and “Maximum bitrat e

DL”, the minimum communication speed (in

kbps) is set for both upload and download traffic

between FOMA terminal and the base station. If

the parameter is set to “None (default)”, all

speeds are permissible. However, if “64” and

“384” are set, any connection at a speed less

than the above limit is not permitted, and

chances are that packet communication will not

be connected.

Example of execution

(1) Command used to permit all speeds both

upload and download (when <cid>=2) AT+CGEQMIN=2

(2) Command used to permit only 64kbps upload

and 384 kbps download (when <cid>=4) AT+CGEQMIN=4,,64,384

(3) Command used to permit 64 kbps upload and

all speeds download (when <cid>=5) AT+CGEQMIN=5,,64

(4) Command used to permit all speeds upload

and only 384 kbps download (when <cid>=6) AT+CGEQMIN=6,,,384

Operation performed when parameter is omitted

AT+CGEQMIN

Clears all <cid> settings.

AT+CGEQMIN=<cid>

Returns the specified <cid> to the default setting.

AT+CGEQMIN=？

Displays a list of assignable values.

AT+CGEQMIN？

Displays the current settings.

■ Command name: AT+CGEQREQ=[parameter]

Sets QoS requested to the network when transmission is performed during PPP packet communication.

Format

AT+CGEQREQ=[<cid>]

Parameter description

Only commands that require connection at 64 kbps upload/384 kbps down l o ad ca n b e se t. The contents are set by default for each cid. <cid>: 1 to 10

By default, “mopera.ne.jp” is registered in cid 1, and “mopera.net” in cid 3.

Example of execution

(when <cid>=2) AT+CGEQREQ=2

Operation performed when parameter is omitted

AT+CGEQREQ

Returns all <cid> to the default setting.

AT+CGEQREQ=<cid>

Returns the specified <cid> to the default setting.

AT+CGEQREQ=？

Displays a list of assignable values.

AT+CGEQREQ？

Displays the current settings.

Result codes

･

When the ATV [n] command (☛P29) is set to “n=1”, the result code is displayed in the text display (default). When the command is set to “n=0”, the result code is displayed in the numeric display.

■ Result codes

No. Text display Meaning

0 OK Operation performed normally 1 CONNECT Terminal connected to remote

2 RING Incoming call 3 NO CARRIER Line disconnected 4 ERROR Unable to accept command 6 NO DIALTONE Unable to detect dial tone 7 BUSY Detecting the busy tone 8 NO ANSWER Completion of connection timed

100 RESTRICTION The communication network is

101 DELAYED Redialing restricted

■ Extended result code

No. Text display

5 CONNECT 1200 1,200 bps 10 CONNECT 2400 2,400 bps 11 CONNECT 4800 4,800 bps 13 CONNECT 7200 7,200 bps 12 CONNECT 9600 9,600 bps 15 CONNECT 14400 14,400 bps 16 CONNECT 19200 19,200 bps 17 CONNECT 38400 38,400 bps 18 CONNECT 57600 57,600 bps 19 CONNECT 115200 115,200 bps 20 CONNECT 230400 230,400 bps 21 CONNECT 460800 460,800 bps

device

out

busy. Please wait for a while and retry.

Connection speed between

FOMA terminal - PC

INFORMATION

● To retain compatibility with a modem connected via conventional RS-232C on PC, communication speed is displayed, but it differs from the actual connection speed because FOMA terminal is connected to the PC with a FOMA USB cable (optional).

■ Comm unication protocol result code

No. Text display Meaning

1 PPPoverUD Connected via 64K data

2 AV32K AV (videophone) connected via

3 AV64K AV (videophone) connected via

5 PACKET Connected with packet

communication

[32K]

[64K]

communication

■ Display example of result codes

When “ATX 0” is set

￥

Regardless of the settings of the AT

V command (☛P29), only CONNECT is displayed upon completion of connection.

Text display example:

ATD ＊ 99 ＊＊＊ 3# CONNECT (“1” in numeric display)

When “ATX 1” is set

･ When “ATX1”, “AT

￥

V0” is set (default) Upon completion of connection, the result code is displayed in the following format: CONNECT <speed between FOMA terminal - PC> Text display example:

ATD ＊ 99 ＊＊＊ 3# CONNECT 460800 (“1 21” in numeric display)

･ When “ATX1”, “AT

￥

V1” is set*

The code is displayed upon completion of connection as follows:

Text display example:

ATD ＊ 99 ＊＊＊ 3# CONNECT 460800 PACKET mopera.net/

64/384 (“1 21 5” in numeric display) Indicates that speed between FOMA terminal and PC is 460,800 bps and the terminal is connected to mopera.net providing a maximum upload speed of 64 kbps and a maximum download speed of 384 kbps.

￥

*1 When “ATX1” and “AT

V1” are set at the same time, it is likely that dialup connection will fail. It is recommended that this function be

￥

usually set to “ATX1” or “AT

V0”.

Foma D902iS User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Data communication

Flow of setup for data communication

Connecting PC to FOMA terminal

Installation of the communication configuration file (driver)

Communicating using the FOMA PC configuration software

Communicating without using the FOMA PC configuration software

AT command